Search Documents

By W. A. McCurdy, Joseph W. Leonard, William F. Lawrence

INTRODUCTION Utilization from the Point of View of the Preparation Engineer The primary interest of the coal preparation engineer is in process design, operation, and maintenance to produce an acceptable product that can be sold at the greatest possible profit. Because of emphasis upon these interests, attention to other potential values of coal is sometimes neglected. The intent of this chapter is to alert the preparation engineer to the utilization possibilities of the product as well as the tributary coal flow moving through a modern coal preparation plant. The basis for any unrealized potential derives directly from the coal seam itself. Most coal seams consist of coal bands and benches sandwiched together in layers that differ visually from each other in physical structure and luster. Randomly selected physical and chemical ranges determined from layers of coal in a single seam can easily differ by as much as 30 Hardgrove grindability indices, 0.30 of a specific gravity point, 20 percentage points of ash, 6 percentage points of dry volatile matter, and 10 percentage points of total su1fur.l Similar wide variations exist for calorific value, seam moisture content, and, undoubtedly, for any other conceivable coal test parameter that might be used for comparative purposes. These observations all point to the long-established fact that coal is not homogeneous, as conventional analytical methods might tend to indicate, but is instead a highly heterogeneous substance.

Jan 1, 1979

By F. F. Aplan

Pollution control will be of utmost importance in the 1970's. In this area, the mineral process engineer has a special competence to understand and remedy many pollution situations. There is an old adage that goes, "Build a better mouse- trap and the world will beat a path to your door." Would that it were so, but the reality of the situation is such that, just as a supplier must sell his machine, a professional man must sell his competence. It is a sad but true fact that mineral processing engineers have not done a very good job in selling their extensive competence in the control of a broad range of pollution problems. Recently one of our students visited a paper pulp mill where he was shown a foam fractionator used to remove paper pulp fibers from plant discharge waters. "Foam fractionator hell, that's a flotation cell!'' was his comment. Ah so, it would appear that large numbers of technical people consider themselves experts on "foam fractionation" Or is it that we have been very remiss in demonstrating the usefulness of our equipment and processes and our professional competence to solve, these pollution problems?

Jan 1, 1970

By R. F. Mehl, G. V. Smith

THE decomposition of austenite in steels, because of its immense practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1-3 Although much information has been acquired a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings-pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. PEARLITE Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix.2-5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth 2 3 Mehl and Smiths have attempted to determine the lattice relationships existing between the ferrite in pearlite and the parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible,[ ]decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrongly, as Mehl and Smith' have pointed out, that the lamellae delineate the {210} planes of ferrite.* MARTENSITE It is known that martensite is a transitional constituent of body-centered tetrag-

Jan 1, 1942

By William Plank

IN PAST YEARS, engineering educators and others have been able to study the problems relating to en-gineering education in the United States with only inadequate and, frequently, inaccurate data at their command. For the first time there is now available fairly full and accurate information on this subject, gathered and compiled by the Board of Investigation and Coordination of the Society for the Promotion of Engineering Education. This board, of which W. E. Wickenden is the director, has for the past four years been carrying out fact-finding investigations into "the objects of engineering education and the fitness of the present day curriculum," under a grant of funds from the Carnegie Corporation of New York. Twelve bulle-tins have already been published by the board and others are in the process of preparation. The studies made, thus far, have been of the various phases of engineering education in general as well as of the major branches of engineering. Within the past year. the board has completed a study of mining engi-neering education by means of a questionnaire sent to members of the Institute. A special committee, con-sisting of Charles E. Locke, Allen H. Rogers and the writer, cooperated with the board in drafting certain parts of the questionnaire and in selecting the mailing list. Similar studies have been made through the mem-bers of the four other national societies. The results of these studies have been published only in mimeo-graphed form, therefore, in order to place the data before the members of the Institute an incomplete sum-mary of the replies to the A. I. M. E. questionnaire is here given. The full report will be available for distri-bution at the annual meeting in February. The questionnaire was sent to 306 members of the Institute, a proportion about equal to the proportion of the membership of the other national societies can-vassed; 152 members replied to the questionnaire, 55 per cent of whom had received college degrees in some branch of engineering connected with the mineral in-dustry. Forty-seven educational institutions were rep-resented in the replies. Seventeen different positions were held by the members who replied, with 24 con-sulting engineers at the head of the list, 20 managers, 16 superintendents, 11 presidents, 10 professors, 6 deans, and others.

Jan 1, 1928

By Cecil Desch

THIS annual lecture, under the auspices of the Institute of Metals Division, and which was illus- trated by lantern slides, has been printed in full and a limited number are available for distribution on request. Some excerpts from the lecture are given below: Ever since the simple geometrical relations of crystals were discovered, it has been recognized that their proper-ties are best explained by assuming that their ultimate particles are arranged on a space lattice, and that the char-acteristics of that lattice determine the shape of the crystal and its physical and mechanical properties. Modern ex-amination by means of X-rays has widened that concep-tion and given it greater; definiteness, and the atoms are now regarded as the particles forming the space lattice. The splendid achievements of investigators in this field have made it possible to state, for a large number of sub-stances, the form and dimensions of the lattice. The char-acteristic of a lattice is that a unit of simple geometrical form is repeated at regular intervals in three dimensions so as to fill the entire crystal. It follows that there must be certain planes in which the atoms are more closely packed than in planes drawn at any angle to them, and it is these planes of closest packing which play the greatest part in determining the growth and other properties of the crystal. There are actually two stages in crystallization, what-ever be the medium in which it occurs. The first is the ap-pearance of crystal nuclei; the second the growth of those nuclei to form crystals of appreciable .size. The first is clearly a kinetic phenomenon. In the molten mass, solu-tion, or vapor, the molecules are in a state of rapid motion and frequent collision. When the temperature has fallen so far. that it is possible for a crystal to exist, a few col-liding molecules may fail to rebound, and so become at-tached to one another, the balance between the attracting and repelling forces-between them causing them to arrange themselves on a space lattice, to which other molecules sub-sequently attach themselves. It was once maintained that the X-ray evidence demanded that the molecule should dis-appear in the solid crystal, but this was a wrong inference, and in many crystals, but not in all, the chemical molecule retains its identity in the solid state. In pure metals the atom and the molecule are identical, so that the conditions are unusually simple. How many. nuclei will be formed in a given mass is evi-dently a problem in probability. Experiments to deter-mine the relation between the temperature and the number of nuclei formed in a given time have been made with some success by using viscous organic substances, but metals offer much greater difficulties, and the few determinations which have been published are vitiated by serious errors. However, the examination of sections of ingots of the same composition and cast at 'the same temperature in similar molds will show, that the number of crystals does not vary widely.

Jan 3, 1927

Continued Discussion of the papers of Van Hise, Emmons, Weed and Lindgren, Bans., xxx., 27, 177, 424, 578. See also the papers of Vogt, Kemp, Rickard, Blake and Lindgren, at pp. 125, 169, 198, 220, 226, and also the final contribution of Prof. Van Hise, p. 284 of the present volume. All the foregoing, together with the discussion here following, are included in the special volume, "The Genesis of Ore-Deposits," issued this year by the Institute. H. Foster Bain, Des Moines, Iowa (communication to the Secretary):* The zinc- and lead-deposits of the Mississippi valley, which it has been my fortune to study, give particularly good examples of many of the principles of ore-deposition formulated by Prof. Van Hise. Perhaps there is nowhere clearer evidence supporting his fundamental tenet., that ore-bodies are to be regarded as a result, and as merely one of the phases, of the work of underground waters. The facts regarding the mines of the upper Mississippi valley have been given in some detail for Wisconsin by Prof. Chamberlint and, more recently, for the mines west. of the Mississippi by the Iowa Geological Survey.‡ Fortunately, also, the processes of underground water-circulation have been studied in some detail in connection with the investigation of artesian waters throughout the region.$ In Missouri and Arkansas the mines and ore-bodies have been much studied ; but the general problems of the circulation of underground waters have been neglected. During the season just closed the writer has been engaged in a re-study for the United States Geological Survey of the zinc- and lead-deposits of the Ozark region, with special reference to those of the . Joplin area; and his full report is now in preparation. It has been interesting to note how fully the statement that the orebodies result from the general action of underground waters is

Jan 1, 1902

By J. E. Lamar

THAT Illinois is an important mineral producing state is well known. A value of over $237,000,000 for the mineral products in 1926 indicates the magnitude of the industries. Coal mining is the largest mineral industry, and the value of its product was about 63 per cent of the total mineral production of the state. Oil and gas constituted about 8 per cent and the non-metallic minerals about 29 per cent. This 29 per cent represents the production of a varied group of mineral industries of wide geographic distribution through the state.

Jan 1, 1929

By C. W. Gennet

Announcement was made in the spring of 1926 that the Boston & Maine R. R. Co. had contracted with the well-known German steelmakers, Messrs. Fried Krupp, for the manufacture of 15,000 tons of basic open-hearth steel rails at the Rheinhausen Works, for delivery to Boston, Mass. The manufacture of rails in the United States has for many years been almost a national pride, and as this feeling is chiefly the result of a long-time liberal and consistent patronage of American rails by American railroads, it is not strange that this somewhat unusual announcement should arouse more than ordinary interest. Since the end of the World War, the importation of foreign rail has been fairly large, principally because the newly created economic conditions have rendered some American competition more difficult, but the tonnage imported, for the most part, has been made up of small orders for miscellaneous use; and the contract referred to constitutes the largest single importation of foreign rail in over ten years. In 1915, the Algoma Steel Co. of Sault Ste. Marie, Canada, supplied the Illinois Central R. R. with 30,000 tons of rails,' and various other American roads with smaller amounts. In 1902, 1903 and 1904, large tonnages of rail from abroad were purchased, the Louisville & Nashville R. R. alone obtaining 30,000 tons from German mills. It is the object of this paper to present, in what is believed to be a new and concise form, figures showing the production and consumption of rails in the United States, and to record some of the testing and inspection results of the recent Krupp rails; also, to direct attention to two quite unique departures from American practice that were regular features of the Krupp process and which are worthy, it is thought, of careful study. Production and Consumption of Rails in the United States Table 1 shows the tonnage of rail produced in the United States and the amount imported, exported, and consumed by years since 1849. That, evidently, was the first year of record, for the statistics of the American Iron and Steel Institute and its predecessor, the American Iron and

By J. P. Doan, G. Ansel

The important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holubl-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British Patent 5111375 relates to the parent discoveries of Sauerwald, Eisenreich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature5. has been found to the particular characteristics of wrought blg-Zn-Zr alloys, with which the present paper is concerned. The work to be discussed represents essentially an extrusion study of the blg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metallography, and toughness of these alloys. Compositional variations are limited to the ranges 0 to 7 per cent Zn and 0 to I per cent Zr. Experimental Procedure Alloying and Casting Alloying ingredients were cell magnesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl² and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manufacturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zirconium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux-inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1947

By G. Ansel, J. P. Doan

The important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holubl-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British Patent 5111375 relates to the parent discoveries of Sauerwald, Eisenreich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature5. has been found to the particular characteristics of wrought blg-Zn-Zr alloys, with which the present paper is concerned. The work to be discussed represents essentially an extrusion study of the blg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metallography, and toughness of these alloys. Compositional variations are limited to the ranges 0 to 7 per cent Zn and 0 to I per cent Zr. Experimental Procedure Alloying and Casting Alloying ingredients were cell magnesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl² and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manufacturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zirconium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux-inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1947

By N. V. Hansell

l. INTRODUCTION. THE last few years have shown an increasing interest in the subject of beneficiating iron-ores -in all iron-producing countries. In the United States, this movement has been slower than in certain parts of Europe, for the obvious reason that the abundance and relative cheapness of the Lake Superior iron ores has hindered the development of enterprises for the preparation of low-grade ores. Gradually, however, conditions have changed. The world's consumption of iron is increasing enormously. Being in 1900 about 40,000,000 tons, in 1910 ii was already 60,000000; and there is no reason to doubt that for the near future the increase in iron-consumption will continue at the same rapid rate, especially with, the development of China, certain parts of Africa, and other regions which have hardly been touched as yet by modern industrialism. It is. therefore, not surprising that apprehension is felt that the known available iron-ore resources of the world are gradually being depleted. Signs of this feeling are the recent investigation, under the direction of the U. S. Geological Survey, of the iron-ore resources of the United States, and the estimate presented to the last International Geological Congress, at Stockholm, Sweden, of the iron-ore resources of the world. These investigations have emphasized the fact that the known high-grade ore-deposits are limited in extent, and will, at a not distant future, be exhausted, compelling the iron industry to depend for raw material on the enormous deposits of low-grade ores which are distributed over almost all the world. The discovery of new deposits of high-grade ore, in countries not yet thoroughly explored, will not materially change this prospect. Of course, the part which such new deposits will play in the future cannot be forecast. The difficulty and cost of transportation will probably exclude many of them from use at the present centers of the iron industry.

May 1, 1912

By Lloyd R. Jackson

IN the past 15 years there has been a great deal of interest in the fundamentals of plastic flow and rupture in metals and a number of papers have presented substantial advances toward a fundamental insight into the mechanism of these two processes. This paper is an appraisal of the present position with respect to the following: I. The relative importance of shear and hydrostatic stresses in controlling the plastic flow of metals. 2. The relative importance of shear and hydrostatic stresses in determining the amount of flow before rupture in metals. 3. The use of generalid strains in determining the effect of plastic flow on the work-hardening of metals. FUNDAMENTALS INVOLVED IN PLASTIC FLOW In attempting to devise a quantitative description of plastic flow in metals, it has been customary to assume that metals are homogeneous and isotropic. The fact that neither of these assumptions is correct complicates the experimental appraisal of relations developed. Never- the less, as will be shown, metals are close enough to being isotropic and homogeneous so that considerable insight into the mechanism of plastic flow can be obtained. The assumptions of .isotropy and homogeneity allow both the elastic and plastic behavior of metals to be described in terms of 12 variables-six being stress variables, and six being strain variables. ) From this viewpoint, it should be possible to represent the stress-strain relations in the plastic range for metals by a surface in 12 dimensions. One boundary of this surface would be the surface of transition from elastic to plastic behavior; the other would be the surface of rupture. These two surfaces would be joined by the surface of plastic flow. The shape of this composite surface would depend on the test temperature and speed of straining. This paper is concerned only with results obtained at constant temperature and constant speed of straining. While such a representation is conceivable, the demonstration of such a surface would present almost insurmountable obstacles. The most fruitful simplification of this concept has been the recognition that the behavior of metals in the plastic region is primarily a result of shear stresses and strains. Based on this viewpoint, it is possible to utilize stress and strain invariants that are independent of hydrostatic components to define an effective stress and strain. In effect, this amounts to reducing the task of representing stresses and strains in 12 dimensions to one of representation in two dimensions. The two invariants (one for stresses . and one for strains) that have received most attention are the following: [ ]

Jan 1, 1946

By E. A. Holbrook

Research, primarily, is finding out the truth. Research applied to enigeering opens the door to new principies and processes, the application of which benefits mankind in a material way. The engineer believes that investigation instituted with the primary view of making the results directly applicable to the industries is the highest type of research. Coal is essentially the basis of modern industrial civilization; therefore, any considerable research pertaining to coal must link itself to the industry by practical application of the results of the research. In other words, all investigational work connected in any way with coal leads to conclusions that permit a better understanding of the origin, nature of occurrence, composition, better and safer mining, more careful preparation, or greater efficiency in utilization of coal. Modern engineering research has been fostered essentially by universities and in the laboratories of institutions of learning. Coal problems that lend themselves to solution in the laboratories have been first attacked and are perhaps the farthest toward solution. For example, a great amount of research work has been carried out with the various phases of chemistry connected with coal. On the other hand, the equally important problems connected with methods of mining have received but little attention, primarily because their solution involves the continued use of a great and expensive laboratory, which is none other than the mine itself. As many of the problems already solved have had chemistry as their background, so many of the problems unsolved have physics as their background; there are also unsolved problems that deal in coal economics. Even psychology must be called upon in future coal-mining research as a basis for solving those great problems that deal with human relationships. 'In general, considerable advance has been made in coal research dealing with chemistry, not so much progress has been made with problems having physics and engineering as a background, while there is a tremendous range of untouched problems that deal essentially with business and psychology. Research in coal mining is not a new development. In the chronicles of the northern coal trade as published in the Transactions of the North

Jan 1, 1920

THIS chapter and the one following deal with the heat quantities involved in open-hearth steelmaking, including the thermal efficiency of the furnace as a generator of high-temperature heat, the heat storage in the steel and slag produced and in the furnace walls, and the heats of the various chemical reactions involved in combustion, in the formation of slag, and the refining of steel. The fundamental laws to be considered are the simplification of the first two ' laws of thermodynamics as applied to problems involving sensible and potential (or latent) heat only 1. Heat input equals heat outflow plus storage. 2. Heat may be transferred only from a hotter body to a colder one. The first of these laws relates to the various heat quantities or the "heat balance" of the process. No one has as yet made an open-hearth heat balance that came out almost exactly balanced, and we assume that the cause lies in the difficulties of accurate temperature and flow-rate measurements at the high temperatures involved and the inherent complexities of flow distribution, air leakage, etc., present in any real, open-hearth furnace system. Some idea of the magnitude of the heat quantities involved can be obtained- by a brief, crude outline of the heat balance of a 90-ton heat of steel. We will assume a 60 to 70 per cent hot-metal charge in a fairly fast working and only moderately efficient furnace, burning fuel oil, with a fuel consumption of around 4 million B.t.u. per net ton. of ingots produced. The time from start of charge to tap is 9 hr. During this period, the oil burned represents 360 million B.t.u., and the sensible heat in the preheated air at the port ends is 117 million B.t.u. so that the total heat input at the ports is 477 million B.t.u. Heat stored in the steel and slag at the end of the heat, plus the various amounts absorbed by certain bath reactions, amounts to a total of 195 million B.t.u., but 120 million of this is supplied by the heat in the hot metal and by various heat--evolving reactions in the bath, so that only 75 million B.t.u. need be supplied to the bath by the flame.

Jan 1, 1944

Jan 1, 1913

By S. B. Casey

[ ] IN 1880, an electric arc was struck over metal for the first time to experiment with controllable melting. The glare of this arc has reflected on the stacks of the steel industry and continued to light the path of steelmakers in their never ending quest -for faster, more economical, and better ways of producing steel. William Siemens is credited with first employing the electric arc to melt metal in a closed hearth and produce basic metallurgical reactions. By the turn of the century, an Italian, named Stassano, was experimenting with ore reduction by the electric arc. In 1899, Dr. Paul Heroult, in France, used the direct arc principle for producing ferro-chromium. His experiments quickly led him to develop a dosed-top arc furnace for the production of steel, and his first commercial shipment was recorded in December, 1900. American steelmakers, quick to sense the possibilities of this method of melting, invited Heroult to our shores, where, in 1905, he was responsible for installing the first arc furnace on the North American continent. This furnace, at Sault Ste. Marie, was built for ore reduction. But Charles Holcomb, founder of Holcomb Steel. Co. of Syracuse, N. Y. contacted Heroult in 1905 and contracted for the first American direct-arc electric furnace for steelmaking. On April 5, 1906, the first heat was tapped from this 3-ton unit. The furnace was basic lined and powered by a single-phase, 500 kw generator, -producing high amperage at low voltage. It is interesting to note that, although the first few heats were made with cold charges, subsequent heats were duplexed. R. H. Bully, first superintendent of Holcomb Steel, persuaded the directors to purchase the unit to effect a more economical and efficient means of making tool steel by duplexing prime melting in a combustion fired furnace, and transfer of hot metal to the arc furnace for temperature adjusting, refining, and adding carbon and alloying elements. Today, duplexing is foreseen by some as the steelmaking process of the future. The promise shown by America's first arc furnace for ingot production quickly led to the purchase of a similar unit by The Firth Sterling Steel Co., in 1909, and to the purchase of the first arc furnace for production of steel castings, by the Treadwell Engineering Co., in 1911. From its humble start in 1906, production of arc furnace steel has never ceased to increase its yearly percentage of total steel production in the U. S., although certain other methods have declined or almost disappeared. By its ability to be used intermittently, the arc furnace gained favor and enhanced its reputation during depression days. When the attack on Pearl Harbor plunged us headlong into the long days of World War II, the arc furnace stood ready, flexible enough to be overburdened hearth wise 30 pct and power wise 25 pct, pouring its endless flood of alloy for the guns, tanks, ships, and planes which ultimately brought victory. During the post war boom, the now, proven virtues of low initial cost, faster installation, better yield, improved availability, and lower operating cost, enabled industry-particularly the small, new, independent producers-to locate strategically and profitably to meet the demand of an America that had been starved for new homes, appliances, cars, and highways. In the Korean police action, the arc furnace again proved itself by providing the latest alloys metallurgists could develop to meet the demands that the jet age and the innovations of guided missiles required. In today's peacetime prosperity, the arc furnace is continuing to provide the economic flexibility required to meet an ever increasing demand for better steel in the face of mounting costs, scrap shortages, and pressure toward decentralized location of industry.

Jan 1, 1961

By Lloyd Pollish, Robert N. Breckenridge

SUCCESS in any underground mining operation is determined by accessibility of the orebody, which in turn is dependent upon maintenance of passage- ways to the mining zones and temporary support of the voids caused by extraction of ore. This is accomplished by one or a combination of the following methods: timbering, back-filling, pillaring, or, more recently, rock bolting. Timbering has usually been the principal means of maintaining these underground openings necessary for mining operations. Timber, however, does not prevent ground movement beyond the scope of localized sloughing, which is indicated by the gradual failing of the timber itself. Besides this, timbering has always been a costly process, and with the decline of available supplies of timber close to the mining areas, mining men have constantly sought other methods of controlling ground.

Jan 7, 1954

By Evan Evans

WITH the expiration on April 30, 1941, of the agreement between the anthracite operators and the United Mine Workers of America, a new agreement was entered into, providing for a general wage increase of 7 1/2 per cent effective May 1, to be brought to a total of 10 per cent on Oct. 1. Contract rates were increased from the rates established under the agreement of September 1923, and hourly rates were raised above the agreement of May 1936 as modified from the eight-to seven-hour day in May 1937. The new rates are to be in force for the duration of the agreement, ending April 30, 1943.

Jan 1, 1942

By B. M. Larsen

A discussion based on three commercial furnace tests and electrical analogue calculations is presented. It shows that while regenerator efficiency is mainly dependent on loading or relative amount of heat exchange surface plus the heat transfer coefficients as effected by flow velocity, the actual air preheat temperature can be high or low, largely independent of regenerator efficiency, mainly due to the diluting or unbalancing effects of cold air leakage into various parts of the furnace system. THERE are many signs of a renewal of interest in the heat regeneration aspect of the open hearth process, among them being the recent paper by Marsh,' the introduction of auxiliary checkers in the stacks of the Isley furnace design, and a number of recent installations of two-pass checkers in new and old furnaces. However, there are also signs of yielding to the usual temptation of oversimplifying a problem. Faced with the job of obtaining better draft on a furnace, for example, a good designer always recognizes that focusing attention on some one factor, such as height of the stack or capacity of the exhaust fan, does not make his problem any easier; rather he must look at the whole system, including such items as valve resistances, bends in the flues, and flow resistance in the waste heat boiler; then he must make his design in relation to the available draft so as to avoid any serious bottleneck in the system. Yet this example is really much simpler than the problem of air preheating, and again, the latter problem is not really made easier by concentrating on air temperature in uptakes and on the more obvious methods for making this air as hot as possible. Also to be considered are such things as the total amount of air needed theoretically for complete combustion at any selected fuel rate, together with that needed for oxygen absorbed into the bath and for burning the combustible gases given out from the bath, plus some excess air. Furthermore, how does this total air requirement relate to the regenerator efficiency at various loadings? How much of the total air equivalent in stack gases will come from preheated air passed through the whole length of the incoming regenerator and how much from air leakage into various zones of the whole furnace system? Does the effect of leakage air differ depending on whether it leaks into the ingoing regenerator, the furnace above floor level, the outgoing regenerator, or the stack zone? Over a number of years we have in this Laboratory experimented with methods for measuring hot gas temperatures; we have measured, approximately, the efficiency of a few regenerators on commercial furnaces and we have developed an electrical analogue' for calculations of regenerator efficiency. The whole problem is too complex to cover in one paper even with a more complete background of data than we possess, but we can attempt here to clarify certain aspects in a general way, hoping to assist specific plant studies on individual furnaces. Some of our earlier experience has been incorporated into chaps. 4, 19, 20, and 21 in the book "Basic Open Hearth Steelmaking,"" and on the assumption that this text is available to most readers, this discussion has been shortened by references to that book. The most recent design of a flowing-gas thermocouple which we are now using for measurement

Jan 1, 1955

By Edward B. Durham

The refinery at the San Francisco Mint takes the bullion purchased by the receiving department, and carrying Illore than 200 parts of precious metals in 1,000, or, in mint parlance, over 200 fine, and separates and refines the various metals contained therein, using electrolytic processes exclusively. Bullion containing silver is treated in cells charged with a nitric electrolyte. These cells produce fine silver and leave a residue rich in gold. The residue from the silver-cells, together with crude gold-bullion, is treated in cells having a chloride electrolyte. These produce fine gold and leave a residue containing silver chloride. The latter is reduced to the metallic state with zinc and is then treated in the silver-cells. The various waste solutions and the wash-waters, after being freed from the bulk of their precious metals, still contain copper and other metals. These are removed by scrap-iron, and are then treated in the copper-cells, having a sulphate electrolyte. These cells produce pure copper, and collect a residue containing lead, some gold and silver, and all the metals of the platinum gronp that were in the bullion. This residue is relatively small, and is melted into bars and stored until suEcient accumulates to warrant treating it for platinum, etc. The refinery occupies three large and three small rooms. The large ones are, a melting-room, 30 by 34 ft.; a cell-room, 39 by 46 ft.; and a wash-room, 30 by 33 ft. The small rooms are used as foreman's osce, laboratory, and , re- spectively. The methods here described are those in use in December, 1909, when notes for the present paper were taken.

Jan 1, 1912