Search Documents

By C. E. Abbott

The Birmingham district, Alabama, is distinctive in the proximity to one another of its deposits of iron ore, coal and flux. These three basic requisites for the making of iron and steel are found within a radius of 10 miles. Both dolomite and limestone are produced, the former for blast-furnace flux and the latter for basic open-hearth operations. The Tennessee Coal, Iron and Railroad Co., a subsidiary of the United States Steel Corporation, operates a limestone mine at Muscoda, near Bessemer, 12 miles southwest of Birmingham, served by its own railroad transportation system. The mine has a capacity of 130 tons per hour. Average analyses of a recent month's production arc as follows: Fe²zO³ SiO² Al²O³ CaCO³ MgCO³ Lump, percent............................. 0.51 0.22 98.63 0.14 Crushed and washed, per cent,................ 0.70 0.26 98.36 0.18 Lump stone, 2 1/2 to 755 in., is used in open-hearth operations at Fairfield Steel Works. Fine crushed and washed stone, 1% to 0.063 in., is calcined at the lime-burning plant and used for lime charges at the Ensley open hearths. Geology The district's deposits of hematite ore occur in the Clinton formation, and the limestone beds mined are stratigraphically 330 ft. above the ore beds worked. A cross section on the center line of the mine is shown in Fig. 1. This limestone formation, 130 ft. thick, is in the Warsaw horizon of the Lower Mississippian. It lies above 100 ft. of Fort Payne chert, which is immediately above the Clinton formation, and is composcd of layers of chert and cherty limestone, approximately 50 per cent of the material being pure chert. The chert is extremely hard, and the cost of driving raises through it is very high. Both iron ore and limestone deposits lie on the southwest limb of the Jones Valley anticline, the formations dipping from 15' to 32' to the southeast. The iron-ore seam outcrops along the crest of Red Mountain, a ridge with northeast-southwest trend rising 200 to 300 ft. above Jones and Shades valleys at the

Jan 1, 1938

By C. E. Abbott

The Birmingham district, Alabama, is distinctive in the proximity to one another of its deposits of iron ore, coal and flux. These three basic requisites for the making of iron and steel are found within a radius of 10 miles. Both dolomite and limestone are produced, the former for blast-furnace flux and the latter for basic open-hearth operations. The Tennessee Coal, Iron and Railroad Co., a subsidiary of the United States Steel Corporation, operates a limestone mine at Muscoda, near Bessemer, 12 miles southwest of Birmingham, served by its own railroad transportation system. The mine has a capacity of 130 tons per hour. Average analyses of a recent month's production arc as follows: Fe²zO³ SiO² Al²O³ CaCO³ MgCO³ Lump, percent............................. 0.51 0.22 98.63 0.14 Crushed and washed, per cent,................ 0.70 0.26 98.36 0.18 Lump stone, 2 1/2 to 755 in., is used in open-hearth operations at Fairfield Steel Works. Fine crushed and washed stone, 1% to 0.063 in., is calcined at the lime-burning plant and used for lime charges at the Ensley open hearths. Geology The district's deposits of hematite ore occur in the Clinton formation, and the limestone beds mined are stratigraphically 330 ft. above the ore beds worked. A cross section on the center line of the mine is shown in Fig. 1. This limestone formation, 130 ft. thick, is in the Warsaw horizon of the Lower Mississippian. It lies above 100 ft. of Fort Payne chert, which is immediately above the Clinton formation, and is composcd of layers of chert and cherty limestone, approximately 50 per cent of the material being pure chert. The chert is extremely hard, and the cost of driving raises through it is very high. Both iron ore and limestone deposits lie on the southwest limb of the Jones Valley anticline, the formations dipping from 15' to 32' to the southeast. The iron-ore seam outcrops along the crest of Red Mountain, a ridge with northeast-southwest trend rising 200 to 300 ft. above Jones and Shades valleys at the

Jan 1, 1938

By Arthur Knapp

The economics of fuel oil must be considered in two aspects; viz., fuel oil as one of a number of competitive fuels and fuel oil as a refined product of petroleum. "Fuel oil" is usually defined as that product of petroleum which is used in furnaces for the generation of heat by simple combustion. It is true that any product of petroleum used in an internal combustion engine is essentially a fuel oil, but such oils are not included in the class known as "fuel oil." Fuel Oil as One of Several Fuels For a number of years, the petroleum industry has believed that the petroleum reserves were very limited and that petroleum products would begin to become scarce within a few years. The industry has believed that there would be a gradual but continual rise in prices as a result of this impending scarcity. The industry, therefore, has informed the users of fuel oil thai., once they were eliminated by price, they were eliminated for all time. The petroleum industry believed and made the consumer believe that there would never be any appreciable recession in price which would make it

Jan 1, 1928

By AIME AIME

The 102d meeting of the Institute was held at the Institute headquarters in the Engineering Societies Building, New York, N. Y., on Feb. 19, 20 and 21, 1912. A Bureau of Information, in charge. of Mr. George Buckman, was maintained during the meeting. The proceedings opened with an informal social meeting on Monday evening, Feb. 19, in Assembly-Room No. 1, on the

Mar 1, 1912

"Butte originated as a placer mining camp. The first gold discovery was made in the year 1864, near what is now Main Street. Placer mining was vigorously prosecuted along Silver Bow Creek and in Missoula, Buffalo, Town and Parrot gulches for a period of five years, at the end of which time, in 1870, the camp was practically deserted. In the meantime, the quartz veins so prominently traceable over the hillsides were located, the first location being made by W. L. Farlin and called the Black Chief claim, and later restaked as the Travona. Reasoning from the presence of the gold placers, free-milling gold ores were eagerly looked for by the early prospectors. Claims covering the great Rainbow and other silver lodes were located in the sixties. The presence of valuable silver ores in these veins caused the staking out of many claims, believed to be valuable only for silver, but which later proved to be enormous copper producers.Treatment of these early discovered rich ores was first attempted in arrastres. Later, stamp mills were built. The Centennial dropping 10 stamps, was the first, and in 1875 Mr. Farlin built the Dexter 10-stamp mill, intro¬ducing chloridizing-roasting. More successful processes were soon introduced and several large mills built, among which were the Alice, Lexington, Silver Bow, Moulton and Bluebird, in all representing a total of 290 stamps. The silver mining industry reached its zenith in 1887 and declined rapidly in the early nineties, following the sudden drop in the price of silver in 1892.During this period of silver mining activity the business of copper mining was making rapid strides. Development of the veins, located as silver veins, had uncovered copper ore in many instances. There was great activity in ""claim staking'' in the years from 1871 to 1879, during which period most of the claims covering the present productive copper area were located."

Jan 1, 1913

NORTH AMERICA ALASKA Anchorage.-Neitzert, G. H. Strandberg, H. Candle.-Robbins, J. S. College.-Barber, R. J. Burns, W. T. Coats, R. R. Fox. E. F. Joesting, H. R. McAnerney, J. M. Colorado Station.-Beyer, A. Stanford, J. V. Douglas.-Cahill, W. E. Carlson, L. Fairbanks.-Crawford, J. D. Earling, R. B. Fowler, D. A. Greves, J. H. Henton, H. M. Herbert, C. F. Hopkins, J. E. Kreitlow, E. J. MacDonald, D., III Mathews, T. C. McCarty, W. J. McNair, W. H. Metcalfe, J. B. Mikami, H. M. Mize, R. J. CANADA ALBERTA Calgary.-Johnson, R. V. Link, T. A. Marple, L. E. Slipper, S. E. Thorne, B. L. Thorne, H. L. Vissac. G. A. Edmonton.-Ball, -M. W. Lilge, E. O. Pitcher, N. C. Nordegg.-Shanks, J. BRITISH COLUMBIA Allenby.-Lindsay, W. R. Bralorne.-Almstrom, A. A. Bosustow, R. Currie, J. M. Gibson, S. Schmitt, D. E. G. Wilson, G. H. Bridge River.¬Botterill, T. C. Crane, G. A.

Jan 1, 1939

By J. E. Chappelear

We are concerned with the problem of calculating the forces produced by passing waves on a submerged object (in particular a drilling barge) located on the ocean floor. We employ the linearized theory of waves (the Airy1 theory), since solutions are generally more easily obtained in such a theory. It will be indicated how an approximate solution to the problem can be obtained for waves of finite height by use of a linear combination of Airy waves. We shall assume the submerged object has an infinite length, thus neglecting diffraction and making the problem two-dimensional. We find that there is not a considerable difference between our solution and the usual engineering solution. The force, as a function of time, is plotted in Figs. 4 and 5, together with the usual solution for easy comparison. So far, no experiments have been found to compare with the results. As will be shown, the calculations can be extended to waves of finite height (Stokes2-Struik3 waves) in an approximate fashion. This can be done by calculating the force produced by each Fourier component of the wave, separately, and omitting the coupling between the various harmonics produced by Bernoulli's theorem. The problem and its boundary conditions will be briefly stated. We seek a function, +, the velocity potential, which is harmonic, ?2?=0...........(1) and which satisfies the boundary conditions ??/?n =0 .......(2) (the normal derivative of + is zero) on the ocean floor and the sides of the barge, and s??/?y = ?..........(3) on the ocean surface, where s = g/w2........(4) The physical reasons for these choices and an interpretation of ? are given by Lamb.' As previously stated, we assume also that the problem is two-dimensional. We set up our coordinates such that x = 0 is the center of the barge and y = 0 is the ocean floor. The coordinates are shown in Fig. 1, together with the location of the barge on the bottom. Our solution may be decomposed into a function which is symmetric about x = 0,?e, and one which is antisymmetric, +,, ? = ? + ?o...........(5) Thus directly above the barge we have as boundary conditions that for x = 0, ?o = 0, ...........(6) and ??e/?x = 0........(7) Now, far from the barge, we have that (for x positive and assuming the waves are incident from the left) ?e ? Ae cosh ky cos k (x + a) , . . . (8) and ?e ? Ao cosh ky cos k (x + ß) . . . . (9) where + means ". .. approaches ... for x large." Let us put Ae, Ao, and k equal to one, and remember that, in accordance with the derivation of Eq. 3, a sinusoidal time factor is to be supplied. Then we may rewrite Eq. 8 for ?e, and we find that

Jan 1, 1958

By Thomas H. Sheehan

The purpose of this paper is to present an application of computer technology to assist the mineral company financial executive in assessing exchange risks. The paper is divided into five parts: Background, Translation Approaches, Theory, Empirical Validation, and Conclusion. BACKGROUND Exchange risk results from a change in the rate of exchange between a host and a home country's currencies. Legitimate reasons exist for changes in the currency exchange rates among countries in a world with over a hundred different currencies. These reasons include: different economic growth rates, social factors, cultural heritages, and political motivations. The problem of exchange rate changes are perennial and exist whether the world operates on exchange rates or floating exchange rate practices. The cause of the problem is trade and international payment imbalances. If one accepts the premise that exchange rates fluctuate over time, then the mineral company financial executive faces a continual process of reassessment of the impact of exchange rate changes on the financial worth of his company. (1) The mineral company financial executive prepares balance sheets and income statements that are audited by certified public account- ants annually for shareholders, bankers, and tax authorities. The financial executive translates assets and equities denominated in foreign currencies into domestic dollars, e.g., Japanese firms convert to Yen, French firms convert to Francs, and so on. When figures from foreign subsidiary operations are consolidated into the balance sheets of the parent corporation, estimates of the company's finan-

Jan 1, 1977

By AIME AIME

THE meeting" of the Rare Minerals and Metals Committee was held Monday afternoon, Feb. 17; Donald M. Lidclell, chairman, presiding. The first paper (T. P. 279), "Progress in the Use of Tantalum," by George W. Sears, was read by Mr. Smyth. Dr. Sears' paper contains an interesting summary of the uses, alloys and ores of tantalum and a resume of present method of reduction. The uses of tantalum is based on its extreme rise to the reaction of even the strong mineral acids, its great avidity for the common gases and its capacity for transforming alternating to direct current. Tantalum, as an alloy material, has received considerable study and many alloys have been reported. Among them three types appear to .be most prominent, alloys of high melting point, hard alloys and acid rising alloys. As the estimated quantity of tantalum in the earth's crust is less than that of gold, it must be looked upon as n rare metal. Australia is the greatest producer and the Black Hills of South Dakota produce minor amounts. As the one type of mineral available contains both tantalum and columbium, the extracting and metallurgy of tantalum are difficult chemical processes. Greater simplicity in this and the development of a market for columbium would undoubtedly be of great benefit to the tantalum industry, andl make for a greater use of tantalum produced.

Jan 1, 1930

By Charles Macdonald

WROUGHT-IRON eye-bars for bridges and roofs, designed upon what is known as the pin connection system, have been successfully manufactured in this country for some years. The most approved methods employed have been the hydraulic upsetting process, and by die-forging under a hammer. In upset eyes the fibre of the iron is necessarily much distorted ; and in bars of considerable size, this disturbance seriously impairs the strength of the connection. Mr. Collingwood, in discussing my paper on "Proportions of the Heads of Eye-bars," read before the American Society of Civil Engineers, Jan. 21st, 1874, submitted sketches of certain bars intended for the anchorage of the East River bridge, which had been exposed to the action of sulphuric acid a sufficient length of time to thoroughly cleanse the surfaces, and expose the condition of the fibre. These sketches are here reproduced for the purpose of illustrating the effect of this methpd of manufacture. In Figs. 1, 2, and 3, it will be observed that the fibres at A, and E, have been folded back upon themselves and otherwise twisted and disturbed, in a manner not calculated to inspire confidence in the integrity of the connection. To compensate for this defect, a large excess of metal is thrown into the eye; but a method of manufacture which involves such a necessity, even although it be the one giving the best results thus far, all things being considered, is far from being perfect.

Jan 1, 1879

Iron Ores and Blast Furnace Practice Concentration of Iron Ores in the United States. By T. R. Counselman. (Metals Technolog), December 1943) Selection of Blast-furnace Refractories. By Hobart M. KrANer and E. B. Snyder. (Metals Technology, April 1944) The Washing of Pittsburgh Coking Coals and Results Obtained on Blast Furnaces. By C. 1). King. (Metals Technology, September 1943) Steelmaking The Role of Basic Slags in the Elimination of Phosphorus from Steel. By Richard L. BArrett and William J. McCaughey. (Metals Technology, April 1944) The Relative Deoxidizing Power of Boron In Liquid Steel and the Elimination of Boron in the Open-hearth Process. By B. W. Gurry. (Metals 'Technology, December 1943) Manufacture and Properties of Killed Bessemer Steel. By C. C. Wright. (Metals Technology, June 1944) Hardenability Effect of Sixteen Alloying Elements on Hardenability of Steel. By Irvin R. Kramer, Robert Hafner and Stewart L. Toleman. (Metals Technology, September 1943) Effect of Quenching Temperature on the Results of the End-quench Hardenability Test. By Clarence E. Jackson and Arthur L. Chrjstenson. (Metals Technology, December 1943) Effect of Some Elements on Hardenability. By Walter Crafts and John L. Lamont. (Metals Technology, January 1944) Effect of Several Variables on the Hardenability of High-carbon Steels. By I?. S. Rowland, J. Welchner and R. IS. Marshall. (Metals Technology, January 1944) Mechanical Properties Influence of Hydrogen on Mechanical Properties of Some Low-carbon Manganese-iron Alloys and on Hadfield Manganese Steel. By Herbert H. Uhlig. (Metals Technology, June 1944) Aging and the Yield Point in Steel. By J. R. LOW, Jr., and 14. Gensamer. (Metals Technology, December 1943) Tensile Properties of Medium-carbon Low-alloy Cast Steels. By H. A. Schwartz and W. Kenneth Bock. (Metals Technology, August 1944) Variables Affecting the Results of Notched-bar 1mpct Tests on Steels. By CLarence 15. Jackson, MYRon A. Pugancz and Frank S. McKenna. (Metals Technology, August 1944) The Notched-bar Lmpact Test. By John H. Hollomon. (Meta1s Technology, April 1944) Hardness Measurement as a Rapid Means for Determining Carbon Content of Carhon and Low- alloy Steels. By K. L. Clark and NIcHols Kowall. (Metals Technology, January 1944)

Jan 1, 1944

Iron Ores and Blast Furnace Practice Concentration of Iron Ores in the United States. By T. R. Counselman. (Metals Technolog), December 1943) Selection of Blast-furnace Refractories. By Hobart M. KrANer and E. B. Snyder. (Metals Technology, April 1944) The Washing of Pittsburgh Coking Coals and Results Obtained on Blast Furnaces. By C. 1). King. (Metals Technology, September 1943) Steelmaking The Role of Basic Slags in the Elimination of Phosphorus from Steel. By Richard L. BArrett and William J. McCaughey. (Metals Technology, April 1944) The Relative Deoxidizing Power of Boron In Liquid Steel and the Elimination of Boron in the Open-hearth Process. By B. W. Gurry. (Metals 'Technology, December 1943) Manufacture and Properties of Killed Bessemer Steel. By C. C. Wright. (Metals Technology, June 1944) Hardenability Effect of Sixteen Alloying Elements on Hardenability of Steel. By Irvin R. Kramer, Robert Hafner and Stewart L. Toleman. (Metals Technology, September 1943) Effect of Quenching Temperature on the Results of the End-quench Hardenability Test. By Clarence E. Jackson and Arthur L. Chrjstenson. (Metals Technology, December 1943) Effect of Some Elements on Hardenability. By Walter Crafts and John L. Lamont. (Metals Technology, January 1944) Effect of Several Variables on the Hardenability of High-carbon Steels. By I?. S. Rowland, J. Welchner and R. IS. Marshall. (Metals Technology, January 1944) Mechanical Properties Influence of Hydrogen on Mechanical Properties of Some Low-carbon Manganese-iron Alloys and on Hadfield Manganese Steel. By Herbert H. Uhlig. (Metals Technology, June 1944) Aging and the Yield Point in Steel. By J. R. LOW, Jr., and 14. Gensamer. (Metals Technology, December 1943) Tensile Properties of Medium-carbon Low-alloy Cast Steels. By H. A. Schwartz and W. Kenneth Bock. (Metals Technology, August 1944) Variables Affecting the Results of Notched-bar 1mpct Tests on Steels. By CLarence 15. Jackson, MYRon A. Pugancz and Frank S. McKenna. (Metals Technology, August 1944) The Notched-bar Lmpact Test. By John H. Hollomon. (Meta1s Technology, April 1944) Hardness Measurement as a Rapid Means for Determining Carbon Content of Carhon and Low- alloy Steels. By K. L. Clark and NIcHols Kowall. (Metals Technology, January 1944)

Jan 1, 1944

By Charles Macdonald

Wrought-iron eye-bars for bridges and roofs, designed upon what is known as the pin connection system, have been successfully manufactured in this country for some years. The most approved methods employed have been the hydraulic upsetting process, and by die-forging under a hammer. In upset eyes the fibre of the iron is necessarily much distorted ; and in bars of considerable size, this disturbance seriously impairs the strength of the connection. Mr. Collingwood, in discussing my paper on "Proportions of the Heads of Eye-bars," read before the American Society of Civil Engineers, Jan. 21st, 1874, submitted sketches of certain bars intended for the anchorage of the East River bridge, which had been exposed to the action of sulphuric acid a sufficient length of time to thoroughly cleanse the surfaces, and expose the condition of the fibre. These sketches are here reproduced for the purpose of illustrating the effect of this method of manufacture. In Figs. 1, 2, and 3, it will be observed that the fibres at A, and E, have been folded back upon: themselves and otherwise twisted and disturbed, in a manner not calculated to inspire confidence in the integrity of the connection. To compensate for this defect, a large excess of metal is thrown into the eye; but a method of manufacture which involves such a necessity, even although it be the one giving the best results thus far, all things being considered, is far from being perfect.

Jan 1, 1879

By Chauncey Berrien

THE Hawkesworth detachable drill steel shank and bit were invented by A. L. Hawkesworth; while he was a mechanical foreman for the Anaconda Copper Mining Co., at Butte, Mont. Mr. Hawkesworth died on June 16, 1925, at the time that his invention was practically a proved success. The first application for patents was made by him in November, 1918, and the bit is now being manufactured under patents issued in 1922 and 1923. The credit, for its development in the early stages belongs to A. L. Hawkesworth, Roy S. Alley, Harry A. Gallwey, E. J. Bowman and various officials of the Anaconda Copper Mining Co. Later improvements, manufacturing problems and the direct usage in the mines were originated and perfected by the mechanical department under C. D. Woodward, E. R. Borcherdt, head of the Rock Drill Equipment Department, Robert E. Kelly of the Mechanical Department, and various operating department heads of the Anaconda Copper Mining Co. The author wishes to acknowledge the assistance of these officials in the preparation of this paper.

Jan 1, 1930

United Engineering Trustees, Inc C E Reistle, Jr (to Oct '55), A B Kinzel, '56, Andrew Fletcher, '57, Philip Kraft (from Oct '55 to '59) The Engineering Foundation W M Peirce, '56, A M Gaudin, '58 Engineering Societies Library Board Frank T Sisco, '58, C H Behre, Jr Engineering Societies Personnel Service Board of Directors E J Kennedy, Jr, E H Robie Advisory Committee, Milwaukee F T Agthe Special Survey Committee C M Cooley American Standards Association Mining Standards Board E R Borcherdt, '55, Otto Herres, '55, J K Richardson, '56, E W Bullard, '56, Alternate

Jan 1, 1955

ALABAMA. Aldrich, Aldrich, W. F. Anmston, Noble, A. E Bessemen, Abbott, C E, Fergusson, V Birmingham, Aldrich, T. H, Aldrich, T. H, Jr, Bowron, J, Burbidge, T A, Collord, G L, Crockard, F H, Davis, F H, Dimmick, F. D., Hiller, E., Johnson, G R, Ludwig, C P., McCormack, G B., McCrery, Peters, R , Jr , Phillips, W B, Ramsay, E ,Shook, A. M Car bon Hall, Pill, J R Emsley, Williams, E P Gadsden, Hudson, J B , Helena, Squire, J Holt, Shook, J W. Huntnnlle, Moss Lehigh, Toulmin. Rock Run, Garvin, J. M. Sheffield, Miller, D I Tusscaloosa, McCausland, E J , Woodward, Woodward, A. H

Jan 1, 1910

Discussion of the papers of Benjamin Talbot. E. A. Beck, Emil Gathmann, Sir Robert A. Hadfield, and P. H. Dudley, presented at the New York Meeting, February, 1913, and printed in this Bulletin (No. 76, April, 1913). CHAIRMAN JAMES F. KEMP :-I call upon Prof. Albert Sauveur to open the general discussion on the subject of sound steel ingots. ALBERT SAUVEUR, Cambridge, Mass. :-I believe that I have the privilege, this instant, of opening one of the most important, significant and far-reaching discussions ever held before this Institute. I believe that our talk this morning will be heard far and wide, not only on this side of the water, but also on the other side. Everywhere, in short, where steel is manufactured. I welcome the opportunity of expressing my mind in regard to the production of sound steel ingots, a subject about which I entertain some very decided opinions. I shall not attempt to discuss the relative merits of the various processes that have been described. I shall, on the contrary, confine myself to a general consideration of the important questions before us. So intensely do I feel regarding the production of sound steel ingots that I have put my remarks on paper in my desire to present my Views.

Jan 4, 1913

E. T. Dumble, Houston, Texas (communication to the Sec-retary?):—In addition to the list of publications mentioned by Mr. Schorr and those by Prof. Hofman, I call attention to the following references:— Sludi sulle Lignite, by Capacci. Turin (1890). (An excellent work.) Report of Brown Coal Industry in Germany. J. Cosmo New-berry. Department of Mines, Victoria (1892).

Jan 1, 1905

By Louis A. Panek

Ground movements in the zone adjoining an active cave were measured at four sites in the San Manuel Mine. Measurements were made to detect extension and inclination, basic components of displacement, which can readily be duplicated by mine personnel using relatively simple equipment. The displacements demonstrated the development of a zone of strain relief surrounding the active cave, within which the ground tends to migrate toward the cave, and extension cracks develop tangential to the cave. This expansion of the ground surrounding an active cave can be exploited to promote future caving; it also creates special problems with respect to the design of an effective ground support system for mine openings in the production area.

Jan 1, 1981

By Edward Keller

(New York meeting, February, 1912.) IN a paper, entitled A Uniform Method for the Assay of Copper Material for Gold and Silver,1 A. R. Ledoux invited the assayers of this country to contribute to a symposium, in which the results of their assays of given samples of copper-matte and metallic copper would be made comparable. This symposium 2 appeared about one year thereafter; and through it and its discussion, first became generally known the fact that the ,gold-yield by the all-fire method of assaying is usually higher than by the so-called combination (wet and dry) method, in which nitric acid is employed as a solvent for the copper. In the publication alluded to, the supposed cause of gold-losses in the latter method was declared to be the solvent action of copper nitrate, or of the reduction-products of the nitric acid, upon the gold. Up to a very recent date, gold has been held to be insoluble in pure nitric acid. (The solvent action of any chlorine present in the nitric acid must here properly be disregarded as belonging in the realm of carelessness. Among later allusions to this topic, W. R. Tan Liew 3 ascribes the solution of the gold in the combination-assay entirely to the action of nitrous acid at the high reaction-temperature of copper and nitric acid ; F. B. Flinn 4 a believes the low result in gold to be due exclusively to mechanical losses-finely-divided gold penetrating through the filter-paper-but presents no experimental data confirmative of this belief; and 0. Pufahl 5 attributes the solubility of the gold in some coppers to the presence of selenium-a view which appears to be shared by many as- 1 Trans., xxiv., 575 (1894). 2 Trans., xxv., 250 (1895). 3 Engineering and Mining Journal, vol. lxix., No. 16, p. 469 (Apr. 21, 1900). 4 Engineering and Mining Journal, vol. lxxxvii., No.11, p. 569 (Mar. 13, 1909). 5 Lunge, Chemische Technische Untersuchungs Methoden, vol. ii., p. 229 (1900).

Jul 1, 1912