Search Documents

By Samuel E. Doak

The utilization of rotary kilns, of the well-known cement type, for the preparation of iron ores for the blast furnace, has become of considerable economic importance within the past 10 years in certain localities, notably those where the native ores are lean. Such kilns may be used simply for the agglomeration of ores too fine to be charged into the blast furnace (i.e., ores whose, loss in the dust catchers is excessive, and whose fineness is detrimental to the working of the furnace), or for the desulphurization of lump and fine ores the sulphur content of which does not exceed 6 or 7 per cent. The desulphurizing action can be combined with that of agglomeration provided the kiln is sufficiently large. Other processes have been developed for the same purpose, but while I am not able to draw a comparison between them by reason of lack of sufficient data, it is safe to say that the kiln, if properly dimensioned for the character of ore to be treated, will compare favorably in its results, both as to economy and quality of product, with any other process. It is not, however, as well adapted for the treatment of flue dust as is a sintering operation, on account of the large percentage of fine coke contained therein. Any combustible entering the kiln at its feed end renders the process very much more expensive and unsatisfactory on account of the difficulty of controlling the temperature, also because of the rapidity with which long "rings" form, due to the increased heat at the cooler end of the kiln. The greatest value of the kiln at present is in the treatment of pyrites cinder; that is, the residue from pyrites ore after the extraction of the greater part of the sulphur. This cinder, while high in iron content, has too much sulphur remaining in it to be allowed to form a large part of the blast-furnace burden, without further treatment. It will range in metallic iron from 42 per cent., representing a very low-grade cinder from a domestic pyrites, to 64 per cent. of the residue from the best Spanish ore, and the corresponding silica content will vary from the maximum of about 25 per cent. to 11/2 per cent. The residual sulphur depends largely on the type of burner used in the original desulphurization. In general, the leanest original ores retain the greatest amounts of sulphur. In modern practice the percentage of sulphur in the cinder is rarely as great as six, and seldom lower than one and one-half. Average analyses for iron, silica, and sulphur of the cinders that have come under my personal observation are as follows:

Jan 1, 1916

By C. F. Willis

The problem of the curtailment of forces in large numbers does not often come to employment departments and is, therefore, a problem that many departments are not prepared to handle intelligently. Those companies that are able to measure the individual efficiency of each man would probably lay off men according to their individual ability, irrespective of dependents, citizenship, or other considerations. During the war when labor was scarce, the business of the employment manager in industry was hiring men and carefully placing them where they were best fitted to work. The careful selection of employees had developed to a considerable extent before the war, and was becoming a recognized science. In the last few months, however, the cancelation of copper contracts, the accumulation of large stocks, the necessary curtailment of production because the copper could not be sold, and the lack of any immediate prospects of' the copper market opening, have led to a universal reduction of forces, and the problem that industry now confronts is that of discharging rather than employing. The problem has been aggravated by the cancellation of contracts in many war industries with the consequent turning loose of hundreds of thousands of men, a great amount of unemployment, and the return of the soldiers and sailors. The problem has now become one of reduction of working force with the least hardship and the least injustice, and yet caring for the soldiers, sailors, and marines who have been in the service of the government for nearly 2 years, and are now returning to their pre-war positions. The Copper Queen Branch of the Phelps Dodge Corpn., operating at Bisbee, Arb., found it necessary, like all of the other copper companies of the country, to reduce its force materially. In making this reduction it was, after due consideration, decided to classify employees with respect to dependents, length of service, and citizenship. The question of individual efficiency or workmanship was not considered. Copper produced to sell at 26 c. a lb. has been selling at under 15 c., and very little copper is being sold at all. Practically every copper producer in the country has enormous stocks on hand, and it would be profitable,

Jan 1, 1920

By M. G. Magnuson, H. O. Hofman

When dry chlorine gas is made to act in the cold upon fiuely-divided gold,' it converts the latter with evolution of heat into auro-auric chloride, Au4 Cl4, a hard, dark-red, hygroscopic salt. Moisture splits this salt into aurous and auric chloride, Au²C14 = AuCl + AuCl³; treatment with water converts it into auric chloride and gold, 3 Au²CI4 = 4 AuC1³ + Au². Aurous chloride, when stirred with water, undergoes a similar decomposition, 3 AuCl = AuCI, + Au,. These decompositions of auro-auric chloride and of aurons chloride furnish the explanation for the practice of moistening an ore before it is treated by the Plattner chlorination-process; practical experience having shown that gaseous chlorine gave an unsatisfactory extraction with dry ore. According to Rose12 fine gold is acted upon more slowly by chlorine than gold containing some base metal, e.g., copper. He also says that small quantities of silver increase the rate of solution, but adds that the coating of silver chloride formed, checks, and finally stops, further action, if the percentage of Silver be increased beyond a certain undetermined amount. Bromine3 acts upon finely-divided gold in a manuer similar to chlorine; the auro-auric bromide, Au²,Br4,, however, is not hygroscopic. Upon treatment with water it is decomposed as is the corresponding chlorine salt. It is generally believed that bromine does not act as energetically upon gold as does chlorine. This seems to be borne out by the results in the leach- +1MASSACHUSETTS INSTITUTE OF TECHNOLOGY, BOSTON, MASS.

Jan 1, 1905

By Karl J. Dreher, Charles C. Hennig, Gregg A. Scott

INTRODUCTION Theodore Roosevelt Dam is a cyclopean-masonry, gravity-arch dam located on the Salt River northeast of Phoenix, Arizona. Construction of the dam began in 1903 and was completed in 1911. The dam is about 85 m high with a total reservoir capacity of about 1.7x109 m3. Raising the dam is now being considered to provide additional water storage and flood control. This paper describes preliminary analyses performed to assess foundation stability for increased loading resulting from raising the dam and reservoir water surface about 12 m. The foundation of Theodore Roosevelt Dam consists of variably metamorphosed limes tones, sands tones, mudstones, and shales. Bedding uniformly strikes nearly normal to the river (N 40º W) and dips upstream at 25 to 30º. The rock is cut by four prominent joint sets as indicated by the joint contour diagram shown in figure 1A. The diagram was developed from surf ace observations and vertical drill core oriented relative to the bedding. Sampling biases account for the differences in concentrations of various joint sets. However, field observations indicate that all sets are relatively prominent, planar, and continuous. SEEPAGE ANALYSES Consistent with practice at the time of construction, no foundation drainage was installed at Theodore Roosevelt Dam. Finite element seepage analyses were therefore performed to study the potential for large uplift pressures in the foundation. The dam has steep abutments and is curved in plan as shown in figure 1B. The effects of modeling the seepage two-dimensionally, radially symmetric about the dam's axis center, and three-dimensionally were therefore com-

Jan 1, 1982

By B. Wilshire, W. J. Evans

W. J. Evans and 8. Wilshire SEVERAL recent investigations1-6 have shown that the strain, c, during transient and steady-state creep is well-represented by the expression: € = e0 + et(l - e-mt) + Esl [l] where Eo is the instantaneous strain on loading, ET the total transient strain, C, the steady creep rate! and m a constant relating to the rate of exhaustion of transient creep. However, it has been noted6 that deviations from this equation occur over the first 10 to 15 pct of the transient stage, when the creep rate, (. decreases more rapidly than is predicted by this equation. This rapid decrease has been attributed to a large change in work-hardening coefficient. It 1s widely accepted that steady-state creep results from a balance between the rate of strain hardcning h and the rate of recovery r (=-s(st) as: dE/dt = Es = r/h [2] Comparison of values obtained for h at the end of the initial extension and during steady creep suggests that h increases several fold during the transient stage. which has the effect of reducing the creep rate proportionally.7 To examine the dependence, on r and h, of the deformation behavior during transient and steady-state creep. a series of constant-stress creep tests was carried out at 413°C at 6000 psi using 70-30 a brass. Prelinlinary investigation showed that. with this material. the transient stage constituted a significant portion of the total creep life (-0.4tf. where tf is the time to fracture). The alloy. obtained from Metals Research Limited. was made from high-purity copper, 99.999 pct. and zinc. 99.99 pct. Heat treatment at 675°C for 4 1/2 gave a uniform grain size of 5 mm-1. Details of specimen preparation and creep testing procedures have been given previously.6 Values of h (?s/?E) were determined by measuring the instantaneous strain. ?E. which occurred on increasing the stress during creep by a small amount. ?s. Similarly. v (= -?s/ ?t) was derived from the incubation period. At, after a small decrease in stress.' Several values of v and h were obtained throughout duplicate creep tests. using different stress increments in the range 300 to 800 psi. The accuracy with which Eq. [I] represents the present creep curves was established by determining the best value of the constants Es, Et, m , and 6, using a digital computer program based essentially on the graphical solution for this equation devised by Conway and Mullikan.9 About 40 strain/time readings were taken during transient and steady-state creep. Over most of the creep curve, the average difference between the measured reading and the calculated strain at the appropriate time was less than 0.0001. However.

Jan 1, 1969

By D. J. Carney, E. Richard Randolph, E. Van Meter, J. J. Oravec, Stanley H. Ward, Gerald J. Anderson, Rolland L. 203-000-000-005 Blake

DURING the last 30 years the inductive electromagnetic method has been used chiefly in the search for massive sulphide mineralization. This application has met with varying degrees of success and in recent years has resulted in discovery of several large orebodies. Little has been written concerning its use in exploration for soft iron ores, but one of the present authors has reported on experiments with massive magnetic deposits.' To augment the exploration tools available to geologists in delineating iron orebodies, Cleveland-Cliffs Iron Co. and McPhar Geophysics Ltd. undertook in 1953 to apply the inductive electromagnetic method to Cleveland-Cliffs properties in the Lake Superior region. As a result of this project, equipment has been developed that enables simultaneous transmission of two audio frequency waves, and the field technique and interpretative procedure involved have furthered exploration in the district significantly. Thus far, inductive electromagnetic application in the Lake Superior region has been only a development tool, that is, it is used to locate obscured contacts and faults as a part of property expansion and development. However, its application to primary reconnaissance of unexplored areas may be feasible in the future. The method has assisted in placing drillholes efficiently, and the elimination of excess drilling foot-ages and/or actual elimination of unnecessary holes has amply justified the expense of the geophysical survey. Cost of the field work involved is comparable on a per station basis to the cost of a magnetometer or superdip survey. Since observations require no reduction, i.e., are directly interpretable, overall expenditure is low, and the scope and detail of the survey can be adjusted in the field as geological- geophysical correlation becomes evident. To a great extent, this eliminates the second-guessing so commonly arising after office calculations are completed on data obtained with other types of geophysical surveys. This unique feature of field interpretation and its associated intimate feel of the project area, is, perhaps, one of the most valuable aspects of the inductive electromagnetic method as applied to iron ore exploration. Basis of Method Fundamentally, the method involves transmission of an alternating electromagnetic wave, of a chosen audio frequency, which permeates the ground materials in the vicinity of a transmitting, or primary, coil, see Fig. 1. This wave, or field, induces an electric current in any conductor on which it is incident. The flow of an alternating current in a conductor sets up its own, or secondary, radiating electromagnetic field. These two fields form a resultant whose configuration depends on the following characteristics of the subsurface conductors: 1) size, 2) shape, 3) electrical conductivity, 4) magnetic permeability, and 5) frequency of the transmitted wave. To a lesser extent the resultant is also dependent on material adjacent to the conductor, topography, and surface conductivity. For illustrative purposes, the primary, secondary, and resultant fields may be represented by vectors. In operation, the direction of the resultant vector is measured by a small receiving coil tuned to the frequency of the transmitted wave. Generally speaking, the method can be compared to the transmission and reception of the familiar radio broadcast, with special variations permitting measurement of the effect on reception of intervening materials. Field Technique Mechanics of field operation are simple. The mast is set up in a vertical position and is then guyed in place. The transmitting loop then is raised by means of a sheave at the top of the mast and the coil connected to the motor-generator. A special plane table is clamped into position on the mast and the loop is plumbed. The plane table is oriented according to a grid system established over the project area. By means of this plane table it is possible

Jan 1, 1956

By D. R. Parrish, V. J. Berry

Reverse combustion is one thermal method of recovering hydrocarbons from porous undergrortnd formations containing oil or tar. In applying this method, air is introduced via an injection well and the mixture of air and hydrocarbons is ignited in the production well. A combustion zone then recedes toward the injection well, counter-current to the air flow. If the combustion-zorie temperature is sufficiently high, the oil or tar irz place is distilled arid cracked. The hydrocnrhon flows as a vapor to the production well and subsequently is condensed at the surface. Maximum temperature and velocity of morcment arc the two dependent variubles defining the progress of the combustion zone. A theoretical analysis has been made of heat flow in the reverse-comhustion process as.srtrning linear flow in a homogeneous system. The differentirll equatious, which include the oxygen-hydrocar-hon rctrction rate, have been solved numerically. Rescllts indicate that the maximum temperature reached and he cornbustion-zone relocity both increase with an incrense in air-injection rote. Heat loss to surroundings has little effect on the maximum comhustion-zone ten?perature achieved, but it is reflected in a reduced com-bustion-zorzc, velocity. It is also predicted that an increase in the oxygen-hydrocarbon reaction rate results in a reduction in the maximum temperature reached. The calculated results are in agreement with results from reverse-combustion experinments using samples of a tar sand. INTRODUCTION Reverse combustion is one thermal method of recovering hydrocarbons from porous underground forma-tions containing oil or tar.' In applying this method, air is introduced into the underground formation via an in-jection well. In one or more adjacent production wells, the mixture of air and hydrocarbons is ignited at the sand face. The combustion zone thus formed recedes toward the injection well, counter-current to the air flow (Fig. 1). Under certain conditions, the rate of recession of the combustion zone is sufficiently rapid that only a small fraction of the hydrocarbon at any point in the formation is consumed by combustion. If the combustion-zone temperature is sufficiently high, the uncon-sumed oil or tar in place may be partially distilled or cracked. This material then can flow as a vapor with the gaseous combustion products to the production well and subsequently be condensed at the surface. Under other conditions, the combustion-zone temperature may be so low that little, if any, of the hydrocarbon is vaporized. Nevertheless, the viscosity of the hydrocarbon may be reduced enough so that other recovery methods subsequently can be applied to produce oil at attractive rates. The maximum temperature achieved in the combustion zone and the velocity of movement are the two dependent variables defining the progress of the combustion zone. Presumably. knowledge of these factors will permit estimates to be made of oil recovery efficiency, oil and gas producticn rates and average amount of injection air required per barrel of oil recovered. The maximum temperature and combustion-zone vclocity are, in turn, expected to be dependent upon air flow rate, heat losses to surrounding formations, physical properties of the rock and the hydrocarbon. the extent to which the porous formation is saturated with the hydrocarbon, the rate of oxidation of the hydrocarbon and the amount of heat released. It is desirable that the relative importance of each of these factors be understood so that the results of laboratory tests of oil recovery by reverse combustion can be properly interpreted in terms of expected field performance. It is particularly desirable to assess the importance of heat lcsses because these are difficult to control or eliminate

James W. Neill, Pasadena, Cal. (communication to the Secretary*):—Professor Hofnlan's paper brings the art up to date. As I was one of the pioneers in this business, I beg to give the following incomplete data regarding my efforts in this line. In the year 1883, while I was in charge of the smelting-operations at Mine La Motte, Mo., there mas at the concentrator an unusually large protluction of a middle product, locally called " iron," which carried considerable values in nickel and cobalt, and which it was desirable, for this reason, to treat by itself. The works could not spare a furnace for the purpose; and to handle this product I improvised a " roast-hearth " from an old " lead-hearth." This was a small cast-iron furnace of the uslial construction, about 2 by 4 ft. in dimensions, with a hollon- cast-iron back, through which the wind circulated before entering the tuyeres. I had a cast-iron grate made to fit this hearth, and placed it tlush with the lip, or apron, and above the tuybres. On this grate, which had round holes about 0.25 in. in diameter, and a total surface of about 20 by 40 in., I roasted the nickeliferous pyrite product; starting the fire with kindling, then adding charcoal, and then gradually feeding the sulphides with a shovel, so as to cover the fire, choke down blow-holes, and get an even bed. Blast at a pressure of 3 or 4 oz. was supplied by a Can-blower. When a cake of roasted material had formed, it was removed with a steel bar, or fork, to the lip of the furnace, and thence into a wheel-barrow. The fine material which had renlained unmelted, but very hot, on top of the cake would promptly ignite when the cake was broken up and removed. The fire would then be covered with fresh material and

Jan 1, 1911

BRANCH COUNCILS MINING BRANCH R M Foose, Chairman (Industrial Minerals) Carroll A Garner (Coal) J V Beall, Eastern Secretary A B Cunmins (Industrial Minerals) R E O'Brien, Western Secretary E D Gardner (Mining, Geology, and Geophysics) Carroll F Hardy (Coal) Philip J Shenon (Mining, Geology, and Geophysics) R E Byler (Minerals Beneficiation) A C. Callen (Mineral Industry Education) Grover J Bolt (Minerals Beneficiation) R J Lund (Mineral Economics)

Jan 1, 1951

By H. E. McKinstry

MOVEMENT on a fracture of irregular shape can cause local widening of the fissure and thereby offer freer channelways for circulation of ore-depositing solutions. This influence, coupled with large areas of wall rock available for reacting with ore solutions in brecciated and shattered ground can account for locally active deposition of metals and the resulting ore shoots. Such irregularities in the fracture system may be caused by local variations in the strength of rocks and by pre-existing lines of weakness, especially if these stand at favorable angles to certain components of the fracturing stress. Therefore correct interpretation of the mechanics of fracturing should permit deductions as to structurally favorable places on unexplored portions of the vein system.

Jan 1, 1941

By P. R. Sahm, T. V. Pruss

Mixtures of fine GaSb and Gds as well as preal-loyed GaSbl,As, powders were hot-pressed at 690°C and 25,000 psi. Dense alloys with compositional gradients of less than 5 pct were obtained from mixtures containing about 20 mol pct GaAs. For x < 0.2, there were increasing compositional gradients, and for x > 0.2 a GaAs-rich second phase appeared in the microstructure. Densification as well as alloying wlechanisms were enhanced by dissociation and, possibly, oxidation reactions of the powders. Densification of coarse prealloyed material, however, primarily depended on plastic flow phenomena and required temperatures just below solidus and pressures of 50,000 psi Thermal and electrical properties were measured. Although in no case was the figure of merit of melt growth materials approached closer than to within 25 pct, the better overall thermoelectric properties were found in coarse-grained, prealloyed materzals which had been compacted to near theoretical density and where grain regrowth had been induced. Similar results are believed to hold in other binary 111-V compound systems if processed under similar conditions. The densification of unalloyed GaSb powders during pressure sintering (= hot pressing) was shown to depend strongly on powder particle size.&apos; Fine powders displayed a "liquid skin effect" that enhanced compaction through the presence of liquid gallium, whereas coarse powders compacted predominantly by plastic flow. The liquid skin effect, in particular, appeared attractive for alloying GaSb with other, higher-melting, III-V compounds, and to densify these in a one-step operation. This is of special interest in the case of III-V compound alloys as the conventional techniques of melt growth or long-time annealing of powders2 is very time-consuming, especially in cases where a large separation of liquidus and solidus can be expected, such as in GaSbl alloys.2 It was felt that experimentation with this system, a particularly unfavorable example, would allow us to extrapolate to several other, more favorable, cases. Uses of Ill-V alloys are most evident in thermoelectric energy conversion devices.&apos; For this reason certain thermal and electrical properties were measured and compared to those of melt-grown material and to hot-pressed prealloyed powders. EXPERIMENTAL PROCEDURE The pressure-sintering apparatus has been previously described.&apos; Using this equipment, both powder mixtures of GaSb with GaAs and prealloyed GaSbl-,As, powders were hot-pressed. The mixtures were pre- pared from cast GaSb and melt-grown GaAs. The prealloyed material was obtained from stoichiometric melts, initially heated to 1200°C in an evacuated quartz ampoule, and then annealed in the solidus-liquidus interval. A typical annealing cycle consisted of a heating to 850°C (1 hr), extended successive annealing at 750°C (65 hr), and slow stepwise cooling (25 hr) to below solidus. The GaSb, GaAs, and GaSbl-,As, materials were ground in a vibrational mill to particle sizes below 500 . A jet mill reduced these further where necessary. Fine powders were analyzed by Coulter counting for their size distribution. Average sizes by volume were calculated from the data. Mixing of the powders, where necessary, was carried out through rapid vibrational motion. The hot-pressing operation consisted of a degassing period of 15 hr, in most cases at 690°C, followed by several hours of compression, normally 25,000 psi at 690°C for powder mixtures and 50,000 psi at 710°C for prealloyed powders. The chemical compositions were confirmed by X-ray fluorescence analysis. To estimate the degree of solid solution achieved, lattice parameters were determined and interpreted according to Vegard&apos;s rule. In addition, optical microscopy helped to correlate the relative amounts of the phases present as well as the degree of porosity to the measured density. To reveal grain boundaries, polished surfaces were etched4 with H 2 O:H 2 O:HCl = 2:l:l. In several cases microscopic concentration gradients were monitored by electron-probe analysis-. RESULTS AND DISCUSSION Alloying and Densification of GaSn-GaAs Powder Mixtures. After preliminary experiments showed that no appreciable alloying took place in mixtures of coarse GaSb (22.5 p) and fine GaAs (2.5 p) powders, hot pressing of mixtures was confined to fine powders only (3.1 and 2.4 p, respectively). Alloying and densification apparently occurred simultaneously with a grain regrowth mechanism which depended on the presence of a liquid phase.&apos; The liquid phase was provided by the dissociation of GasbS particles into liquid gallium and antimony above 555°C. This not only enhanced grain regrowth and densification, as in unalloyed GaSb,&apos; but took on additional importance here for the alloying process. Alloying was speeded up by the resulting liquid-solid interaction as compared to the very slow solid-state diffusion process normally expected at these temperatures.&apos; The results obtained with a series of powder mixtures have been compiled in Table I. It is seen that for mixtures with less than 20 mol pct GaAs, x < 0.2, the compositional ranges increased and for x > 0.2 a GaAs-rich phase and free antimony appeared in the microstructure in sizable amounts.

Jan 1, 1968

By P. A. Beck, L. J. Demer

As reported in a previous publication,&apos; isothermal grain growth in high purity aluminum and in an aluminum alloy with 2 pct magnesium can be adequately described by means of the empirical relation: Here, D is the average gain size after an annealing period 1. The annealing period includes the time for complete recrystal-lization R, and the time for gain growth 1,. D, is the pain size as recrystallized, n is a parameter depending on the temperature and on the material. The effect of 2 pet magnesium in solid solution was to decrease D, and to increase R, A and n at a given temperature. The present work was undertaken in order to investigate the above listed-effects of magnesium in solid solution, as functions of the magnesium content. The work also includes the study of certain anomalous effects observed in the recrystal-lization and grain growth of the 2 pct magnesium alloy at 350°C. Experimental Procedure The method of producing the ingots used in this work was described in detail1 and need not be reproduced here. The materials used were high purity aluminum, furnished by the Aluminum Co. of America, of lot analysis shown in Table r and magnesium from a high purity distilled stock of magnesium crystals. Table i—Lot Analysis of High Purity Aluminum Per CeNt Si.................................... 0.00~ Fe.................................... 0.002 Cu................................... 0.002 Mg................................... 0.003 Mn................................... o. oox Ingots were prepared for a series of binary aluminum-magnesium alloys of increasing alloy content. The numbers used to designate these ingots and their magnesium contents by chemical analysis are given in Table 2. Table 2—Ingot Numbers and Magnesium Contents Ingot Number Pct oa Magnesium aI 2.05 22 1.80 24 0.12 26 0 02s The analyses showed no difference in composition between the top and the bottom of the ingots. Spectrographic analysis of the ingots for elements other than magnesium showed, within the limits of accuracy of the method, no increase in impurities over the amounts given in the lot analysis for the high purity aluminum in Table I. Careful microscopic study of ingot 21 in the as-cast condition, at magnifications up to I 500X, revealed a cer-

Jan 1, 1949

AARONS, J. BOYD, Major. AGNEW, FRANK VANS. ALLEN, HERMAN H., Private, D Co., 8th Reserve -Engineers. AMBLER, HARRY A., Second Training Camp, Ft. Sheridan, Ill. BAINS, THOMAS M., JR., Major, Engineer Officers&apos; Reserve Corps. BANKS, H. R., Lieutenant, Canadian Engineers, B. E. F. BARBOUR, PERCY E., Deputy Supt. (Captain), New York State Troopers; Captain, 22c1 Regiment, N. Y. N. G. BARLING, H. B., 1st Lieutenant, Engineer Officers&apos; Reserve Corps. BARRETT, LESLIE P., Lieutenant, A. E. F., France. (Unattached.) BENSEL, J. A., Major, Engineers&apos; Reserve Corps. BIGELOW, BRAXTON, Royal Engineers, B. E. F. BLOOMFIELD, E. C., Lieutenant. BORROW, F. K. BOWLES, MARTIN F., 2d Lieutenant of Infantry, Camp Funston, Kans.

Jan 10, 1917

By T. Wasson

The same limitations&apos; that characterized 1931 existed in the old fields of Indiana and Illinois during 1932. Prices remained low. The average for the year for Illinois and southwestern Indiana was $1.032 as against $0.852 for 1931 and $1.616 for 1930. In September a curtailment of production of about 25 per cent became effective and was continued to the end of the year. There were no new discoveries and very little wildcatting was done. Considering the age of the wells, and the number still producing, there were few abandonments. The most outstanding thing about the old fields in these states is their long continued productivity. Illinois The fields along the southeast end of the LaSalle anticline had their peak of 33,686,000 bbl. in 1908. In 1932, with a 25 per cent restriction for 355 months, these fields produced 4,661,000 bb1.l There were 52 new completions (most of them in old territory) and of these 33 were dry, 8 were gas, and 11 were oil wells. The new oil wells had a total initial of 102 bbl., or an average of 9.3 bbl. per well. Nineteen of the new producers were in Crawford County. There were about 200 wells abandoned in the old southeast fields in 1932 as compared to 210 in 1931. The greatest number, 86, were in Lawrence County. To the end of 1932, the four major counties—Clark, Crawford, Lawrence and Wabash—had produced almost 394,000,000 bbl. from 92,160 acres. Better than one-half of this was produced in Lawrence County from 26,240 acres. The Dupo area of Sinclair County had no additions to production although four wells were drilled. On the Jacksonville structure in Morgan County, six gas wells with an average depth of 300 ft. were drilled to sands in the base of the Pennsylvanian. They produced an open-flow total initial of 2,000,000 cu. ft. This gas will be developed further to supply a local market.

Jan 1, 1933

By AIME AIME

[SECRETARY&apos;S NOTE.-Since the Committee on Publication of United Engineering Society, will issue a memorial volume re¬porting these proceedings in full, an outline only will be here given. The sessions were held in the Main Auditorium.¬R. W. R.] COMMITTEES. EXECUTIVE.-J. W. Lieb, Jr., Chairman; C. W. Rice, Secretary; John Hays Hammond, Chas. Wallace Hunt, F. R. Hutton, Charles Kirchhoff, T. C. Martin, E. E. Olcott, Chas. F. Scott, Samuel Sheldon, Ambrose Swasey. INVITATIONS.-R. W. Raymond, Chairman; Charles Kirchhoff, Secretary; A; C. Humphreys, Robert W. Hunt, L. B. Stillwell. PROGRAM.-A. R. Ledoux, Chairman; C. W. Rice, Secretary; Theodore Dwight, Chas. Wallace Hunt, T. C. Martin, Ralph W. Pope, Joseph Struthers. WAYS AND MEANS.-James Douglas, Chairman A. R. Ledoux, Secretary; H. R. Brown, J.-M. Dodge, C. L. Edgar, John Hays Hammond, W. M. McFarland, E. E. Olcott, Samuel Sheldon, J. G. White. HISTORICAL AND PUBLICATION PRESS.-T. C. Martin, Chairman; Albert Spies, H. H. Suplee.

May 1, 1907

By G. E. Pralle

INTRODUCTION The decade from 1969 to 1979 saw the crest of a wave of investments by companies and investors, primarily from the major industrial nations, in the metals and minerals industries of the so-called lesser developed countries. This was brought about by two major considerations: 1). The higher ore grades and therefore the higher profit potential of the mineral deposits in the third world countries, and 2). The desire, particularly by the European countries and by Japan, to ensure a safe supply of raw materials not available in their own countries. The decade began with the start of the Toquepala mine in Peru and the major investments in the Bougainville mine in Papua New Guinea and the Ertsberg mine in Indonesia. It ended with the start-up of Southern Peru Copper Company (SPCC) Cuajone mine in Peru and Inco&apos;s Soroako mine in Indonesia and the investments in several major alumina or aluminum projects in Australia and Brazil. Concurrent with this huge flow of funds into the mineral resources industry of the developing world was the build-up of a psychological fear in the host countries of exploitation/domination by the foreign investors. This resulted in an increasing trend towards: 1). Nationalization of existing mineral ventures, and 2). Tougher legal/fiscal frameworks for new ones. NATIONALIZATION Nationalization appeared in its earliest form as "Mexicanization" of the petroleum industry in Mexico in the 1930&apos;s, followed later by Mexicanization of the mining industry in general. This was enacted with the Mexican Mining Law of 1961 which required that 51% of the equity be owned by Mexican nationals. Later in the decade the equity share for foreign investors was reduced to 33 1/3% for the developers of the Frasch sulphur operations in the Isthumus of Tehuantepec. However, the law was not fully implemented in the copper industry until late 1970 with the purchase of 51% of the ownership in the Cananea Mining Company. The trend toward nationalization of the copper industry progressed to Chile where in 1967 under the Government of Eduardo Frei the major North American copper companies were induced to sell a one-half interest in their Chilean mines to the State. Likewise, in 1970, "Zambianization" took place, when the two major operating companies Roan Selection Trust (Amax) and Zamanglo (Anglo American) were restructured into Roan Consolidated Mines (RCM) and Nchanga Consolidated Mines (NCCM) providing the government with 51% of the equity ownership. Whilst the earlier forms of nationalization in general constituted a fairly priced buy-out (El Teniente, Chile for US$80 million, RCM for US$117.8 million, NCCM for US$178.7 million), the total nationalization of the Chilean mining companies in 1970 under Salvador Allende did not. Later, "Western" countries joined this trend and on October 29, 1973, Mr. Gough Whitlam proclaimed that "overseas capital must continue... in partnership with Australian capital" and "in some special energy cases we have an objective of 100% Australian ownership". In 1974 Mr. Pierre Trudeau stated: "The Liberal Party of Canada sets as an objective that new resources projects in the natural resource field should have at least 50% and preferably 60% Canadian equity ownership". FOREIGN INVESTMENT The situation for the foreign investor in the worldwide resource industry rapidly deteriorated from then on. New features appeared in mineral exploitation and operating agreements, centering not only on local government/local companies ownership but also on increased taxation. The new tax rate (mineral tax, royalty, and income tax) for the semi-government companies NCCM and RCM in Zambia became an effective 73%. Likewise the much publicized and discussed renegotiated Bougainville agreement brought dramatic increases in the total "take" by the PNG Government. More innovative forms of indirect taxation made their appearance and were added to the normal tax burdens of the mineral industry which already

Jan 1, 1985

By Donald A. Brobst

The minerals barite (BaSO4 barium sulfate) and witherite (BaCO3 barium carbonate) are the chief commercial sources of the element barium and its compounds whose many uses are nearly hidden among the technical complexities of modern industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry which in 1973 consumed at least 80% of the world&apos;s produc¬tion of 4.4 million tons as a major ingredient of the heavy fluid, called mud, that is circulated in rotary drilling of oil and gas wells. The re¬maining 20% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite occurs throughout much of the world and is available from three major geologic types of deposits-vein and cavity fill¬ing, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world&apos;s demand for barite is expected to increase, and geologic circumstances are favor¬able for the discovery of new deposits of com¬mercial value. Witherite is much less common and abun¬dant than barite, although it is more desirable in many ways as a raw material for the pro¬duction of barium chemicals. The United States has not produced witherite since about 1950; England is currently the chief producer of witherite. End Uses Most of the world&apos;s barite production since 1926 has been used as a weighting agent for the muds circulated in rotary drilling of oil and gas wells. The muds fundamentally are mixtures of water, clay, and barite in different proportions that vary according to local reservoir condi¬tions. Muds with a specific gravity as great as 2.5 are used. The mud is pumped down the hollow drill stem, passes through the bit at the bottom of the hole, and rises to the surface in the space between the drill stem and the wall of the hole. In the course of this circulation the drill bit is cooled, cuttings are removed, the drill stem is lubricated, the walls of the hole are sealed, and the hydrostatic head of the column of weighted fluid helps to confine high oil and gas pressures. The latter feature aids in prevention of gushers, thus reducing both environmental pollution and waste of oil and gas resources as well as conserving the natural reservoir pressure for greater production and rate of recovery of the products contained in the rocks. Barite is particularly well suited for drilling mud because it is clean, easy to handle, soft (nonabrasive), heavy, virtually inert chemi¬cally, and relatively inexpensive compared to many other available heavy materials. Barite is used in the manufacture of glass in continuous tanks. The addition of barite ho¬mogenizes the melt and gives greater brilliance and clarity to the finished glass. Ground barite, both unbleached and bleached by sulfuric acid, is a common industrial filler, extender, and weighting agent. The rubber in¬dustry is a major consumer of barite as a filler. Barite also is added to bristolboard, heavy printing paper, playing cards, rope finishes, brake linings, clutch facings, plastics, and li¬noleum, to name but a few uses. Bleached barite has long been an extender in white lead paint because of its weight. The low index of refraction of barite, however, makes its ability to cover marks poorer than some other sub¬stances, but its low capacity for absorption of oil is a good feature. Off-color or unbleached barite can be used as a filler in colored paints. In the construction industry, some lump barite is used in concrete aggregate to weight down pipelines buried in marshy areas and to shield nuclear reactors. Because barite absorbs gamma radiation well, its use reduces the amount of expensive lead shielding otherwise

Jan 1, 1975

Jan 1, 1882

All branches of our profession may look back &apos;with pride upon the patriotic service rendered by engineers during the war. That war has been won. The mortal danger which it threatened has been averted. But the effects of the torture inflicted by it still remain, a fever in the blood of the body politic. Fever begets delirium and, unless its course be checked, has a tendency to produce convulsions. The only safe course is to take immediate steps to allay the fever. The seat of the present trouble is industrialism; as production is at the foundation of civilization, a diseased condition there carries pain and consequent unrest into every member of the organism. Who shall supply the cure? Quack doctors, nostrums in hand, rush forward from all directions promising to perform miracles. But sane men know that no miracles, though invoked by star gazers of purest intention, will prevent or accelerate the orderly operations of the laws of nature and of human life. Delirium must be controlled by the firm, gentle hand of intelligent, sympathetic authority. Fever must be allayed first by removal of all poisons from the system, then by consistent ministration of cooling, quieting restoratives, then by simple, wholesome nourishment. Nature will, under such treatment, supply the permanent cure.

Jan 12, 1919

By G. Sachs, G. Espey

SIMPLE methods can be used for the determination of the residual stresses in thin-walled tubing if the stresses consist of high tensile stresses at the one surface and high compressive stresses at the other surface Such a stress distribution is approximated in sunk tubing and in deep-drawn shells It is possible to cut sections from such articles in such a manner that a major part of the residual stress is relieved by a bending of the part that is separated from the adjacent metal The circumferential stress is evaluated from the change in diameter D, occurring on splitting a length of tubing (Fig Ib),1-5 or from deflection resulting from the cutting out of a circumferential tongue (Fig Ia) G The bending moment M released by such a flexure is [ ] The release of this bending moment corresponds to the release of stresses, which, in a thin section, vary linearly from one surface to the other, and have the following value in a particular fiber a certain distance (zx from the surface [ ] where C is the section modulus and d is the thickness of the section, the ratio AI C being d 2 for a rectangular section* The maximum stress values at the surfaces are [ ] For most purposes the simpler equations [ ] will be satisfactory, where Dm is the average of the mean diameters of the tubing

Jan 1, 1941