Search Documents

By C. Dirksen

This study investigates whether oxygen consumption during segregated forward combustion may be affected by natural convection. Linear theory indicates that thermal instability occurs in a horizontal porous medium when the modified Rayleigh number N 'Ra exceeds a critical value of about 40. Most experimental results, including those described here, indicate this value to be about an order of magnitude smaller. N ', is derived from "differential similarity" and the proper time scale factor is also obtained. The critical value of N'ra for a horizontal, water-saturated porous medium at atmospheric pressure subjected to a uertical temperature gradient was found to be about 3.0. The ambiguity in the value of N'R, arising when fluid properties cannot be assumed constant is indicated. Natural convection was observed for oblique systems below N 'Ra , while simultaneous horizontal flow did not affect N Racrit. The expected range of values for the various parameters pertaining to segregated forward combustion is indicated and the corresponding values of N 'Ra calculated. Only under very favorable conditions, such as high permeability, high pressure and low top temperature, can the critical value of N 'R, be exceeded. Thickness of the convection layer should not become too large, since the time required to obtain significant mixing is proportional to the square of the thickness. For an oblique combustion frant the conditions for significant mixing may be less strenuous. LNTRODUCTION Laboratory1,2 and field314 experiments have shown that a markedly upgraded oil can be produced by in situ forward combustion. Under certain conditions injected air may move through a high permeability, gas-saturated channel over the oil-saturated layer, while combustion takes place, exclusively, at the horizontal interface (Fig. 1). Such a channel may be a natural gas cap, or it may result from a forward combustion process in which injected air and combustion gases fingered through the top of the formation, causing a premature breakthrough at the production well. In this particular case of segregated forward combustion, the air stream moves parallel to the combustion front. Molecular diffusion and transverse mechanical dispersion will be insufficient to cause all the oxygen in the air stream to reach the combustion front. When the oxygen in the air stream is not completely consumed in the combustion process, it will reach the production well and create a serious fire hazard. In addition, the reduced efficiency may make the process economically unprofitable while also serious corrosion problems may be experienced in the production we11.3 This undesirable situation should, therefore, be prevented. However, in a situation as depicted in Fig. 1, an unstable temperature gradient exists in the gas phase. The combustion is taking place at the lower boundary at a nearly constant temperature that may be anywhere from 600 to 1,200F, depending on the conditions. The upper boundary of the gas phase is overlying, impermeable rock; its temperature might be around 100F, but may increase to 300F or higher due to conduction and convection as the combustion process continues. This represents a steep temperature gradient and it is conceivable that under those conditions free or natural convection will take place in the gas

Jan 1, 1967

By Edward F. Fitzhugh

Quantitative appraisal of the chances of finding various tonnages and grades of ore clarifies any exploratory development proposal. Ways are discussed of appraising chances in conformance with probability principles, and graphs are suggested to show tonnages, grades and the corresponding judged expectancies. Introduction When exploratory development of a mineral deposit is contemplated, three interrelated questions normally must be answered before a sound decision can be reached. How much will the program cost? How much will the anticipated ore add to the immediate value of the mine? And what is the chance of developing this ore? To justify development, the deposit should present a favorable disparity between the three factors, cost, chance and return. If, for example, there is a 50-50 chance of success, the ore that is sought should have an immediate worth (after deducting all subsequent charges that it must bear) of more than twice the cost of the development. Likewise, if the chance of finding the ore is but one in five, that ore should enhance the immediate value of the mine by more than five times the cost of developing it- With sound economic and operating assumptions, the cost of exploratory development and a present value of anticipated ore may be estimated within reasonable limits. Less general attention has been given to appraising ore chances in comparable terms. The exploratory experience of the mining industry is broad enough that knowledge, vision and judgment may be combined to yield more tangible evaluations of Ore expectancy than are now customary' A way of making such appraisals is suggested herein. The mathematics of probabilities cannot be applied directly to the search for ore. By coupling applicable principles of probability, however, with pertinent experience gained in mineral exploration, an estimate often can be made of the chance of finding a certain tonnage and grade of Ore in a specific location. Such estimated, or judged, expectancies for the several blocks of ground in a deposit may be combined in a simple chart to show the relationship of the various exploratory possibilities and the potential magnitude of the deposit' An engineer or geologist may find that the quantitative thinking required for an appraisal of this type is an aid in clarifying and coordinating his views and recommendations. For a person wishing to understand these views, an ore-expectancy

Jan 1, 1949

By Edward F. Fitzhugh

Quantitative appraisal of the chances of finding various tonnages and grades of ore clarifies any exploratory development proposal. Ways are discussed of appraising chances in conformance with probability principles, and graphs are suggested to show tonnages, grades and the corresponding judged expectancies. Introduction When exploratory development of a mineral deposit is contemplated, three interrelated questions normally must be answered before a sound decision can be reached. How much will the program cost? How much will the anticipated ore add to the immediate value of the mine? And what is the chance of developing this ore? To justify development, the deposit should present a favorable disparity between the three factors, cost, chance and return. If, for example, there is a 50-50 chance of success, the ore that is sought should have an immediate worth (after deducting all subsequent charges that it must bear) of more than twice the cost of the development. Likewise, if the chance of finding the ore is but one in five, that ore should enhance the immediate value of the mine by more than five times the cost of developing it- With sound economic and operating assumptions, the cost of exploratory development and a present value of anticipated ore may be estimated within reasonable limits. Less general attention has been given to appraising ore chances in comparable terms. The exploratory experience of the mining industry is broad enough that knowledge, vision and judgment may be combined to yield more tangible evaluations of Ore expectancy than are now customary' A way of making such appraisals is suggested herein. The mathematics of probabilities cannot be applied directly to the search for ore. By coupling applicable principles of probability, however, with pertinent experience gained in mineral exploration, an estimate often can be made of the chance of finding a certain tonnage and grade of Ore in a specific location. Such estimated, or judged, expectancies for the several blocks of ground in a deposit may be combined in a simple chart to show the relationship of the various exploratory possibilities and the potential magnitude of the deposit' An engineer or geologist may find that the quantitative thinking required for an appraisal of this type is an aid in clarifying and coordinating his views and recommendations. For a person wishing to understand these views, an ore-expectancy

Jan 1, 1949

By AIME AIME

TWO weeks ago the writer was lunching in the Engineers` Club in New York with a man who has perhaps the widest acquaintance among engineers of anyone in the country a member of another of the Founder engineering societies. "By the way," lie asked. "who have they nominated for your next president."' "Doctor Becket," I told him- "Oh. that's line," he replied, in a heartfelt tone that rang with sincerity. "I have come in contact with him occasionally and he is just the right type.' And that is the way Dr. Frederick M. Becket impresses everybody. The right type. Most Institute members of the western group of hard-rock minors do not know him, but then they meet him in his swing around the circle next year they will not require a long acquaintance to sense his kindly and outstanding personality, to realize that he is a gentleman in the bet meaning o1 that word, a man of wide sympathies and interests.

Jan 1, 1932

By J. L. Bray

LEAD has often been suggested as a protective coating for iron and steel. Such a protective coating should possess: (1) good adhesion, (2) durability, (3) ease of application, (4) freedom from pinholes, (5) good appearance and (6) low cost, but, unfortunately, lead coatings so far produced do not have all of these characteristics. Because of the necessity of carrying out the coating process cheaply, and because lead solutions have poor plating characteristics, most of the efforts have been directed toward the hot-dipping process rather than electroplating. The hot-clipping processes using lead have not been successful chiefly because of the lack of adherence between iron and lead. In any coating process involving iron a bond can be obtained only by the formation of an intermetallic compound, the formation of a solid solution, or mechanical means. Lead forms with iron two immiscible liquid solu-tions, and in the solid state no intermetallic compounds or solutions. It is necessary, therefore, to employ some other element or elements as a binding agent. Tin may be used as in terneplate, or copper in the form of a thin film of electrolytically deposited metal to which the lead will adhere. Because of its physical and chemical properties, lead as a coating medium would undoubtedly be limited in its use to sheet and wire and then only when the article is not subject to abrasion or wear. A very large tonnage of these products are being used under such conditions and a successful lead-coating process should be a valuable contribution to the science. Two other difficulties stand in the way of successful lead coating-that of poor appearance of the weathered surface and the tendency of the lead to form pinholes during solidification. Since lead is commonly accepted as cathodic to iron, these exposed areas are ones of accelerated corrosion.

Jan 1, 1937

By A. T. Beckwith

This paper concerns measurements of low-velocity air currents and investigations on mine ventilation by means of chemical smoke. The chemical smoke used is produced without flame and at ordinary mine temperatures, and therefore presents no ignition hazard in gaseous mines. Mining men who have worked in open-light mines are familiar with the use of tobacco smoke in determining the direction of air travel and approximately measuring low-velocity air currents. The use of chemical smoke is merely a refinement on the use of tobacco smoke and the flameless low-temperature source of chemical smoke has the additional advantage that it can be used in gaseous mines. Ventilation smoke apparatus, Fig I, is a simple device for producing dense white smoke. The apparatus as shown consists of a rubber aspirator bulb which is used to force air through a glass "smoke tube" containing a chemical substance that produces a dense white smoke on contact with air. The apparatus was developed by engineers of the U. S. Bureau of Mines.' It is inexpensive, weighs less than 3 oz, is easily carried in a pocket, and requires no skill to operate. Smoke apparatus is invaluable in practical mine ventilation work for: (I) measuring low-velocity air currents, (2) detecting air leakage, (3) observing airflow characteristics. This paper is written to show the merits of the apparatus, and is based upon findings through its extensive use, during the past six years, in mines operated by the Lehigh Navigation Coal Co. Inc. The Apparatus Certain chemicals, such as stannic chloride (SnCl4) and pyrosulphuric acid (H2S2O7) produce "white smoke" when exposed to air. Stannic chloride gives off vapors which on contact with moist air cause the formation of solid hydrates, of which SnCl4.5H20 is the most important. Pyrosulphuric acid decomposes when exposed to air with the evolution of sulphur trioxide (SO3) fumes, which become white upon contacting moisture in the air. A chemical, such as one of the above, is the active substance in a smoke tube. The glass tubes are hermetically sealed during manufacture, and are made ready for use by merely breaking off the tips at the conveniently located file cuts. When the smoke tube is connected to the aspirator, depressing the aspirator bulb forces air into contact with the chemical, and smoke discharges from the open end of the tube. A white solid (a hydrate if stannic chloride is used, or sulphur trioxide if pyrosulphuric acid is used) may occasionally form a cake in the outlet opening of a smoke tube. A small wire such as an ordinary paper clip can be conveniently employed to dislodge the cake should it seal the tube. When the assembled apparatus is not

Jan 1, 1949

By T. T. Read

In discussing the taxation of mining enterprises, it is desirable to place limits of both time and space on the field of discussion. For our present purposes it seems best to limit consideration to taxation of mining enterprises in the United States, and to further limit the subject to taxation under approximately current conditions. Even with such limitations the field is large enough, since in this country we have, in most regions, a number of taxing powers; so that state, county and village tax systems must ordinarily be considered, in addition to our national or federal taxes. Nor is it possible, in discussing United States mineral taxes of today, altogether to pass by similar taxation in earlier periods, or related systems in other countries. It is perhaps hardly necessary to remind you, at the outset, that each age in the history of the world displays its own system of public revenues, and that the taxation systems of today are everywhere different from those of older times. Theories as to taxation have varied according to the economic basis of the society in which they were formulated, and our ideas as to justice in taxation fluctuate with changes in social conditions. The word taxation is used in a fairly definite sense today, but you have only to glance into the history of taxation to find that the paragenesis of ore deposits is a fairly simple subject as compared to the paragenesis of taxation systems.

Jan 1, 1932

By H. C. Chang, N. J. Grant

Creep of very coarse grained, high purity aluminum was studied at 400° to 1100°F with an initial stress range of 50 to 1200 psi. The process of boundary sliding and migration was studied. The driving force of boundary migration under creep conditions is shown to be a combination of strain energy migrationand surface energy. A theory is presented regarding the strainenergyrole the grain boundaries play under creep conditions. From this thetheory intercrystalline failure of commercial alloys can be explained. Also from this theory an optimum grain size should exist for good high temperature properties of high purity materials. IN the investigation of the creep of very coarse grained, high purity aluminum previously reported,' the cyclic nature of the process of grain boundary sliding and migration has been established by microscopic observation of the actual creep process as well as metallographically. It was also substantiated by measuring localized strains across the grain boundaries. In addition, it was shown how extensive subgrain and fold formation may result from boundary sliding and how the slid grain boundary may become sharply wavy as a result of subgrain formation. Since the publication of those results, additional information on the process of grain boundary sliding and migration has been obtained. It is the purpose of this paper to report on the direction and driving force of boundary sliding and migration, the effect of grain size, and the effect of temperature. Finally the effect of decreasing purity (alloys 2s and 3s) on the process of boundary sliding and migration is noted. From these results, an explanation is presented for the intercrystalline failure of alloys under creep conditions. The effects of grain size on the creep properties of impure and high purity materials are discussed in the same light. The experimental procedures and technique have been presented elsewhere.' It is only necessary to state how the 2s and 3s aluminum specimens are prepared. Machined specimens were first annealed at 600°F for about 12 hr. In order to produce a large grain size the specimens were then stretched 3 to 8 pct. The specimens were marked with reference marks, electropolished, annealed at 900°F for 24 hr and at 1150°F for 12 hr, and repolished. The grain size of 2s aluminum produced by this treatment is comparable to that of high purity aluminum in the direction of its width of the specimen, i.e., there are 2 to 4 grains across the width of the specimen. However, the grains of 2s aluminum are 3 to 10 times longer in the direction of the specimen axis. On the other hand, the grain size of coarse grained 3s aluminum ranges from 10 to 20 grains across the width of the specimen due to the treatment just outlined and therefore is much smaller than that of both high purity and 2s aluminum. As in 2s aluminum, the grains are about 3 to 10 times longer in the direction of the specimen axis than in the direction of the width of the specimen. The arrangements of the grains in 2s and 3s aluminum were generally irregular; therefore it was difficult to follow the course of the grain boundaries. Results Method of Presentation: In order to show the arrangement of the grains, especially the direction and positions of the grain boundaries, traces of the grain boundaries on the four surfaces of the specimens were unfolded and mapped out after macroetching. Figs. 1 and 2 show the structural development drawings of specimens P-3 and P-8 respectively. The two flat surfaces (of which the front one faces the microscope) and the round-edged surfaces will be called the "front surface" and "back surface" and

Jan 1, 1954

By Holbrook G. Botset

It is possible by means of the electrolytic model to simulate water-flooding or gas recycling systems involving input and output wells, and also the encroachment of a natural water drive. The results are obtained pic-torially, and by simple measurements and calculations the percentage of recovery is obtained qualitatively as a function of the total input. Introduction The increased demand for petroleum products, together with the decline in discovery rate and the higher cost of recovery as deeper formations are brought into production, has stimulated interest in methods for studying and predicting efficiencies of various production programs. Among methods Of recovery that have become of increased significance recently are gas recycling in condensate fields and secondary recovery by water-flooding. The electrolytic model is a useful device for studying such methods in the laboratory, at least in a qualitative way. The original experiments with electrolytic models and the development of their application to the study of secondary reCoverY problems were published in 1933. 1,2,3 Subsequently other investigators continued the development and modification of the bait method, with resultant improvements and extension of its applications.4-7 The method and equipment to be described here are thought to represent still further improvement in the results obtainable, with increased validity in their application to field problems. Sand OF Principles of Operation The underlying theory of the operation of the model is given in references I, 2 and 3. However, a brief statement of principles involved is given herewith. The applicability of the model is based on the fact that Ohm's law and d'Arcy's law are exactly analogous; whence, electrical flow through a conducting medium may be used to simulate homogeneous fluid flow through a permeable medium. If two electrodes are placed in a conducting (ionized) solution and connected to the positive and negative terminals of a source of direct current, the positive ions of the solution will move toward the negative terminal, Since the velocity of an ion in an electrolytic medium is proportional to the electrical gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the motion of the ions in the potential field will be the same as the motion of fluid particles in a porous medium if the positive and negative terminals (input and output wells) and boundary conditions are made equivalent in shape and distribution. In order for the analogy to hold exactly, the sand must be assumed to have uniform porosity and permeability and the input

Jan 1, 1946

By Holbrook G. Botset

It is possible by means of the electrolytic model to simulate water-flooding or gas recycling systems involving input and output wells, and also the encroachment of a natural water drive. The results are obtained pic-torially, and by simple measurements and calculations the percentage of recovery is obtained qualitatively as a function of the total input. Introduction The increased demand for petroleum products, together with the decline in discovery rate and the higher cost of recovery as deeper formations are brought into production, has stimulated interest in methods for studying and predicting efficiencies of various production programs. Among methods Of recovery that have become of increased significance recently are gas recycling in condensate fields and secondary recovery by water-flooding. The electrolytic model is a useful device for studying such methods in the laboratory, at least in a qualitative way. The original experiments with electrolytic models and the development of their application to the study of secondary reCoverY problems were published in 1933. 1,2,3 Subsequently other investigators continued the development and modification of the bait method, with resultant improvements and extension of its applications.4-7 The method and equipment to be described here are thought to represent still further improvement in the results obtainable, with increased validity in their application to field problems. Sand OF Principles of Operation The underlying theory of the operation of the model is given in references I, 2 and 3. However, a brief statement of principles involved is given herewith. The applicability of the model is based on the fact that Ohm's law and d'Arcy's law are exactly analogous; whence, electrical flow through a conducting medium may be used to simulate homogeneous fluid flow through a permeable medium. If two electrodes are placed in a conducting (ionized) solution and connected to the positive and negative terminals of a source of direct current, the positive ions of the solution will move toward the negative terminal, Since the velocity of an ion in an electrolytic medium is proportional to the electrical gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the motion of the ions in the potential field will be the same as the motion of fluid particles in a porous medium if the positive and negative terminals (input and output wells) and boundary conditions are made equivalent in shape and distribution. In order for the analogy to hold exactly, the sand must be assumed to have uniform porosity and permeability and the input

Jan 1, 1946

By R. R. Harvey

Recent evidence has indicated that the films forming at crude oil-water interfaces are the result of naturally occurring su,rface-active components in the crude oil rather than oxidation products resulting from exposure of the oil to air. Since the presence of such films may strongly affect the displacement of oil from porous media, a knowledge of their composition and formatiorz is of fundamental importance. In this study, without the assumption of a specific mechanism, film formation is considered to involve the transfer of a weakly surface-active species in solution in the oil to the oil-water interface. The film gas law and the Gibbs adsorption equation may thus he applied to the system. The rigid films which form upon decrease of the oil-water interfacial area are considered a result of the very slow rate of re-solution of the film material into the oil. When the shrinkage of the interface is very rapid, the amount of film material leaving the interface is negligible, and the system may then be treated in the same manner as an insoluble film. The combination of these treatments leads to a new concept of the film factor in which it may he quantitatively related to the concentration of film-forming material at the interface. Suitable experiments can then yield the following information. 1. Original concentration of surface-active species in the oil. 2. The change of concentration with time. 3. Concentration of surface active species at the interface. 4. The change of this concentration with time. 5. Interfacial tension of the system at any time and its variation with time. 6. Equilibriunz concentrations for a given set of conditions. 7. Concentration requirements for solid film formation. 8. Molecular diameter of the adrorbed species. These calculations may be made solely from data taken from measurements on the original oil. While using the pendant drop method of interfacial tension measurement of crude oil-water systems, Bartell and Niederhauser' remarked on the thin, transparent, pliable, solid films or membranes which were often formed at the interface between crude oil and water. As a result of their observations of these films, Bar-tell and Niederhauser concluded: 1. The films are formed by material from the oil adsorbed at the interface rather than by a reaction at the interface. 2. The adsorption of the film-forming material is a rather slow process. 3. There are good indications that the process is reversible; i.e., the film constituents may re-dissolve into the oil. 4. The film will spontaneously spread over any new surface formed. 5. The process of adsorption at the interface is accompanied by a decrease in the interfacial tension of the system. Although they had proved that film formation was not due to a reaction at the interface, Bartell and Niederhauser were unable to demonstrate conclusively whether these film-forming constituents were present in the original reservoir oil or whether they were formed as oxidation products after exposure of the oil to air. Recent evidence seems to point to their presence in the original oil. Although the true nature of the film-forming constituents is still uncertain, these conditions would be fulfilled by the assumption of the presence of a slightly soluble surface-active component in the original oil. This component would migrate to a freshly formed interface because it would thereby lower the free energy of the system. The component at the surface constitutes an expanded monolayer which would become compressed, upon retraction of drop, due to the slow rate of re-solution of the film components into the bulk of the oil. It is possible, by involved extraction processes, to separate or at least concentrate this film-forming fraction. However, using the assumptions made above, the technique of monolayer film study may be applied to reveal much of the nature of the adsorbing material without resorting to an actual separation of the film-forming constituents.

By W. D. Robertson

THE effect of a tensile stress in accelerating the corrosion-cracking of certain alloys of aluminum, magnesium and iron is widely recognized. The literature is extensive and it is only necessary to cite the recent ASTM-AIME Symposium.1 There are, however, no experimental data conclusively showing the effect of an applied compressive stress. It has been inferred, from the generally accepted mechanism postulated for the acceleration of corrosion by an applied tensile stress, that a compressive stress would inhibit corrosion. Furthermore, it is observed that corrosion cracks invariably start on the tension side of a specimen bent as a simple beam. This observation has led to the suggestion that shot-peening of the surface would inhibit or eliminate stress-corrosion cracking in magnesium alloys, and aluminum alloys.3 However, the degree of inhibition produced by shot-peening does not appear in the literature except for the above qualitative references which are unsupported by experimental data. Moreover, while peening undoubtedly imposes a surface compressive stress, the alteration of the surface by the severe cold-working involved complicates the interpretation of the results with respect to the effect of a compressive stress alone. If corrosion proceeds along preferential paths produced by precipitation from solid solution, it is easily understood how a component of tensile stress normal to these paths will accelerate the corrosion and lead to ultimate failure. On the other hand, if the metallurgical conditions are such as to create preferential corrosion paths, then it is difficult to understand how a compressive stress, produced by shot-peening or any other method, can inhibit corrosion except in the sense that the accelerating factor is removed. Thus, if the basic corrosion mechanism remains unaltered, there should be little or no inhibition resulting from the application of a compressive stress if in¬hibition is defined as the reduction of the degree of corrosion below that experienced in the unstressed state. The experiment described below was performed to isolate and evaluate the effect of a compressive stress on the corrosion and stress-corrosion cracking of a high strength aluminum alloy (24-S); and, by a comparison of the corrosion rate of specimens subjected to an applied tensile stress, compressive stress and in the unstressed state, to clarify the role of stress in intergranular corrosion. EXPERIMENTAL PROCEDURE The experiment was conducted with the aluminum-copper-magnesium alloy known as Duralumin 24-S.* Specimens, 0.064 in. thick, in the form of I in. wide strips sheared parallel to the rolling direction,

Jan 1, 1947

By B. M. Larsen, L. S. Darken

Some years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2) by a high concentration of active (or "free") lime and of manganese oxide dissolved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. Distribution 02 Manganese between Slag and Metal at Equilibrium On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction FeO + Mn -& MnO + Fe [A] slag metal slag metal the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as K,, _ aMnO' afe aFeO ' aMn where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term afe may be combined with K" to give a new constant K'. Making these changes, 7

Jan 1, 1942

By B. M. Larsen, L. S. Darken

Some years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2) by a high concentration of active (or "free") lime and of manganese oxide dissolved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. Distribution 02 Manganese between Slag and Metal at Equilibrium On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction FeO + Mn -& MnO + Fe [A] slag metal slag metal the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as K,, _ aMnO' afe aFeO ' aMn where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term afe may be combined with K" to give a new constant K'. Making these changes, 7

Jan 1, 1942

By C. E. Mills

Studies of ground movement and subsidence resulting from mining operations cover a broad field. It is also a very important consideration and one that eventually affects nearly every mining operation of any extent. The damage to surface buildings, removal of mine surface plants and replacements of main hoisting shafts must reach an astounding expenditure were these cost figures available over a period of years. Were the subject one of mathematical formula and dependent only on the angle of draw of the walls or country rocks, the problem would be relatively simple. Consideration must be given to depth and extent of workings; structural conditions of the orebodies and enclosing country rock; physical properties of these same rocks, including schistosity, bedding, jointing, slips, dikes, faults, and other structural weaknesses. The method of mining, extent of openings, supporting pillars, and amount of moisture or water underground are other pertinent factors. With such a large number of variable factors, it is apparent that the subject of subsidence is one that must be based largely on experience and results at other mines where conditions are somewhat comparable. In presenting this paper, it is the intent to describe the progressive results of past ground movements at the United Verde, to bring out physical conditions largely responsible for this movement, but to refrain from theorizing on the ultimate extent of subsidence resulting from future mining operations. Geology and Structure1 The ore deposits of the United Verde are of the massive sulfide, schist-replacement type. A structural anticline formed by the intrusion of diorite between bedding planes of steeply dipping and severely folded greenstones and porphyry localized the deposit of sulfide. The mineralized zone is of great horizontal extent varying from 200,000 to 400,-000 sq. ft., and extends from the surface to the lowest levels at a steep dip of from 50° to 75. The irregular interfingering of the sulfide with

Jan 1, 1934

By Morris Muskat, James M. McDowell

A report is given of electrical analog experiments on the effect of casing perforation completions on well productivity for ideal uniform reservoirs under steady state homogeneous fluid flow conditions. Graphical results are presented for the effect of perforations of different densities and various degrees of penetration into the formation surrounding the casing or cement sheath. The latter range from perforations which terminate flush with the casing to those which extend into the formation a distance equal to the casing diameter. For the special case where the perforations terminate immediately beyond the casing with semi-spherical protrusions the electrical analog results correct and supersede previously reported theoretical calculations. It is found that the penetration of the perforations into the surrounding productive section may so increase the resultant productivity as to approach or even exceed that for open hole completions. INTRODUCTION A theoretical analysis of the effect of casing perforation on well completion, without additional penetration of the formation, was reported several years ago.' In this treatment the perforations were represented by mathematical sinks and no explicit account was taken of the imperviousness to flow of the casing in which the perforations were made. This procedure was justified by consideration of the mutual interference between the sinks, which seemed to indicate that the analytical method automatically eliminated flow across the casing radius between the perforations. However, both further theoretical investigation and the electrical analog measurements described below showed that this assumption in the previously developed theory was not valid and that the calculated well capacities would considerably exceed the correct values. § Even if this simplifying assumption were retained the generalization of the theory to situations where the perforations extend into the producing formation would be extremely difficult. On the other hand, the electrolytic model analog of this type of steady-state homogenous fluid system is, in principle, so simple that it has not been worthwhile to attempt to develop the exact analysis even for the more limited case of strict casing perforation. The whole problem has therefore been studied anew by electrical models to cover the range from holes in the casing which terminate flush with the casing surface to such as extend into the surrounding rock to a depth equal to the casing diameter. It is to be expected that the productivity of a well completed with casing radius* rw, perforated with holes of radius Tp, and extending to depths d into the surrounding rock, would depend primarily on the dimensionless geometrical parameters Te Tw TP d of the system, such as —, —, — , and —, where re is the Tw, a a rw external boundary radius and a is the mean vertical separation between the perforations. It will also depend, of course, on the number of perforation lines or total perforation density. While such parameters automatically control analytical treatments, it would require a very extensive series of model experiments to fully disclose their functional effect on the well productivity. For practical purposes, however, a rather limited range of the variables suffices to give the effects of interest. Accordingly, in the experimental study reported here the casing diameter has been kept fixed? at six in., the perforation diameter has been taken as either one-fourth in. or one-half in., their density has been varied from one to eight per ft, and their penetration into the formation has ranged from zero to six in., with a primary scaling factor of one to six. EXPERIMENTAL METHOD AND RESEARCH Although electrolytic model experiments have been made for years, there still seems to be some question as to what set of conditions will give the best results. For this reason a number of electrode materials and electrolytes were tried. Those chosen for the final experiments were copper electrodes and a weak copper sulphate solution as the electrolyte. This 'Assuming that the casing has been cemented with a uniform and impermeable cement sheath, the effective casing radius is to be interpreted as the external radius of the cement annulus. It is also assumed here that the casing is set through the complete producing section that it is perforated throughout with a uniform density and that tie formation has a a and isotropic permeability. As noted later, however, a uniform scale change permits reinterpreting the primary measurements to correspond to a casing diameter of 12 in.

Jan 1, 1950

By P. D. Gorsuch, D. L. Newhouse, Irvin R. Kramer

ALTHOUGH many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical, properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application and tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + ? ? ? , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann,2 in his work on the hardenability of quenched steels, and Walters,3 in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield and tensile strength .4 This is not true, however, for normalized

Jan 1, 1946

By L. W. Legerwood

During the past three decades, the oil industry has expended increasing eflorts seeking improved drilling tools or systems to reduce drilling costs. The total cost of these efforts is unknown, but it certainly amounts 10 tens of millions of dollars. Most of the "new" system that past and present investigators have sought to develop actually are old public information. In seeking to implement new-systern concepts, investigators have tested the following: impact at frequencies ranging from 6 to 300 cycles per second; electrical, mechanical and hydraulic meam of actuating percussors; bit rotary speeds up to 2,000 rpm; electric and hydraulic bottom-hole means of rotating bits; bottom-hole machines with power outputs up to 400 hp; shock waves; explosives; high-velocity pellets; flame; arc; grinding wheels; abrasive jets; erosion by high-velocity gases; chemical attack; electric current; magnetic waves; retractable rock bits; reelable drill pipe; continuous coring with reverse circulation; and automation of drilling rigs. Table I shows how these investigations are grouped for discussion purposes in this paper. In spite of these efforts to discover new and improved systems, rotary drilling main;aim its economic leadership. Undoubtedly, rotary drilling costs will continue to be reduced by rigid application of the best available technology and by development of new rotary technology. In view of the extensive past development programs, however, significant long-range improvement appears to be a research, not a development problem. Research must postulate and prove theories and principles governing variour subsurface rock-failure processes pertinent to both rotary and new systems. Ah, research must produce physical and engineering data relative to these processes. When such information is available, earth boring will graduate from an art to a science. Major improvements in rotary drilling can then be expected, and the systematic evolution of an improved drilling method can be initiated—with a strong probability for success. Development of drilling methods other than rotary drilling has been one approach investigated by the industry as a means for reducing drilling costs. Major cost-reduction efforts, however, have been centered on engineering development work aimed at incremental improvements in rotary drilling. A relatively minor effort has been expended to establish basic physical principles and engineering data pertaining to the earth-boring process which can serve as a foundation for the development of cost-cutting drilling hardware. Current oil-industry economic trends have added impetus to the need for effective programs to reduce drilling costs. However, areas for expanded future efforts should be selected only after careful study of past investigations. It is the purpose of this paper to review past and Dresent industry efforts to develop new drilling tools or systems and to suggest areas where additional science is needed. Past reviews of drilling methods have been limited to a few processes prominent at the time the reviews were made. This paper seeks to present a concise, well organized review of all methods that have received actual development or test work. The preparation of a paper seeking to review all past developments is fraught with many difficulties, not the least of which are errors in or obsolesence of printed matter used as source material and the lack of data on industry developments which have not been published. Since de-

With a mine output as high as 5000 tpd and mill capacity of 7000 tpd, the uranium mining and milling complex owned and operated by Kerr-McGee Nuclear Corp. in the Ambrosia Lake area is the largest in the U.S. and is likely to remain so for some time. Next year, Kerr- McGee expects to have in production another mine in Section 19 of the Ambrosia area-and will begin ore production in 1976 at its new $15-million mine at Church Rock, located northeast of Gallup, N. M., where the company has already completed the shaft work and is in the early stages of project development. Ore from Church Rock will be transported to the company's facilities at Ambrosia Lake for processing. Kerr-McGee's existing eight mines in Ambrosia Lake go to depths of about 800 to 1500 ft to tap the various horizons of uranium-bearing sands in the Westwater Canyon of the Morrison formation.

Jan 8, 1974