Search Documents

By C. D. Woodward

THE subject of electric signals for the despatching off mining cages through shafts has received cousiderable attention recently from various mining companies. The Anaconda Copper Mining Co. has found it necessary to develop a system that is reliable, safe and simple in operation, and easy to repair. The movement of all mine cages or skips is under the direction of a station tender, who rides on the cages when men or supplies are being lowered or raised. When ore is hoisted, he is stationed at a skip pocket for loading and despatching the skips. For the station tender's use, two signal systems are installed in each hoisting compartment, and he is the only employee authorized to use them. One system is known as the "AC" or Station bells, as it is operated from the 110-volt, 60-cycle, power service; the other system, called the "DC" or shafts bells, takes its energy from closed-circuit primary batteries. As a supplement to the two main signals, a buzzer system is installed. The general arrangement is similar to "the main signal, except that there is a mine buzzer at each station. When a signal switch connected into the buzzer system is pulled down, all buzzers are operated, thus notifying the station tender that he is wanted at some particular level. Placed on the station posts, and within easy reach of the men on the cages, are the signal pull switches for the main signals. The station, or "AC," pull switches are furnished with a short rope as shown in Fig. 1, while the shaft, or "DC," pull switches are equipped with ropes that extend down the shaft past the next station. To avoid all confusion in the use of the three signal systems, a standard arrangement has been adopted in all mines for the location of the pull switches. Fig. 2 illustrates the position of the pull switch at the various mine stations for the main signal systems, but it does not show the buzzer pull switch; this is fixed to the roof timbers about 25 ft. back from the shaft. If the skip pockets are a considerable distance below the station, a pull switch for each main shaft compartment is connected to the "AC" system and placed at this point. However, if the distance is short, a light cord is attached to the station pull switches and dropped down to the skip pocket.

Jan 2, 1922

By W. D. Robertson

The effect of a tensile stress in accelerating the corrosion-cracking of certain alloys of aluminum, magnesium and iron is widely recognized. The literature is extensive and it is only necessary to cite the recent ASTM—AIME Symposium,l There are, however, no experimental data conclusively showing the effect of an applied compres-sive stress. It has been inferred, from the generally accepted mechanism postulated for the acceleration of corrosion by an applied tensile stress, that a compressive stress would inhibit corrosion. Furthermore, it is observed that corrosion cracks invariably start on the tension side of a specimen bent as a simple beam. This observation has led to the suggestion that shot-peening of the surface would inhibit or eliminate stress-corrosion cracking in magnesium alloys and aluminum alloys. However, the degree of inhibition produced by shot-peening does not appear in the literature except for the above qualitative references which are unsupported by experimental data. Moreover, while peening undoubtedly imposes a surface compressive stress, the alteration of the surface by the severe cold-working involved complicates the interpretation of the results with respect to the effect of a compressive stress alone. If corrosion proceeds along preferential paths produced by precipitation from solid solution, it is easily understood how a component of tensile stress normal to these paths will accelerate the corrosion and lead to ultimate failure. On the other hand, if the metallurgical conditions are such as to create preferential corrosion paths, then it is difficult to understand how a compressive Stress, produced by shot-~eening Or any other method, can inhibit corrosion except in the sense that the accelerating factor is removed. Thus, if the basic corrosion mechanism remains unaltered, there should be little or no inhibition resulting from the application of a compressive stress if inhibition is defined as the reduction of the degree of corrosion below that experienced in the unstressed state. The experiment described below was performed to isolate and evaluate the effect of a compressive stress on the corrosion and stress-corrosion cracking of a high strength aluminum alloy (24-S); and, by a Comparison of the corrosion rate of 'pecimens subjected to an applied tensile stress, compressive stress and in the unstressed state, to clarify the role of stress in intergranular corrosion. Experimental Procedure The experiment was conducted with the aluminum-copper-magnesium alloy known as Duralumin 24-S.* Specimens, 0.064-in. thick, in the form of I-in. wide strips sheared parallel to the rolling direction,

Jan 1, 1949

By E. S. Machlin

The wzodel of Blandin and Diplunt;, generalized to include a phase factor, is applied to the carbon-carbon interaction in iron. Darken&apos;s "energetic" model is generalized to include not only first neighbor interactions but further neighbor interactions as well. On the bases of these generalized models relations are derived for the activity of carbon in both austenite and ferrite in terms of the carbon-carbon Pair interaction energies. A single function then yields the pair interaction energies consistent with the experimental activities of carbon in both ferrite and austenite. Thus, a simple explanation is given for the observation that the nearest-neighbor interaction between carbon is repulsive in austenite and attractive in ferrite. Certain consequences of this approach are explored. OnE object of the present paper is to attempt to take into account the consequences of electrostatic contributions to the carbon-carbon pair interaction energy for carbon as a solute in iron. Friedel&apos; has shown that oscillations in electrostatic potential are to be expected about a solute atom in a metallic solution. Blandin and 6lant6&apos; have shown that such oscillations yield an interaction energy between pairs of solute atoms that obeys the relation: W{ = A cos(2ftFri + 4>)/(kFri)3 [l] where kF = Fermi wave vector, ri = distance between solute atoms comprising the pair7 <p = phase factor dependent only on electronic nature of solute and solvent, A = coefficient dependent only on electronic nature of solute and solvent. Machlin3 found that Eq. [I] accurately described the pair interaction energy derived from short-range order measurements based on field ion microscope observations of dilute alloys of platinum. He also found that the value of the phase factor $ derived from residual resistivity measurements agreed well with that obtained from the analysis of the short-range order data. Harrison and paskin4 were able to predict the long-range ordering energy of 0 brass using Relation [I] and residual resistivity values to predict the value of the phase factor $. Machlin5 has repeated their analysis and applied it to the prediction of the long-range ordering energy in AgZn and AgCd with excellent agreement between prediction and experiment. Both A and $ are independent of the crystal structure. The Fermi wave vector depends uniquely upon the conduction electron concentration per unit volume in the spherical approximation of the Fermi surface. Thus, Eq. [I] is expected to apply to both fer- rite and austenite with only one set of values of A and $. Mossbauer studies6 yield the result that iron has one 4s electron. We shall make an assumption found to hold previously for platinum3&apos;7 and nikel, which is that only the s electrons are involved in shielding the perturbing potential of carbon. With this assumption, kF = 1.35 A-l. Although A and $ may be obtained from certain mdels&apos;&apos;&apos; we shall take A and $ to be empirical constants in the spirit of Kohn and osko.&apos; Thus, Eq. [I] involves two adjustible parameters. Consequently, two independent relations in A and $I are required in order to evaluate them for carbon as a solute in iron. We may use a recent analysis of Aaronson, Domain, and poundg who showed that Darken&apos;s energetic model,1° as well as others, can be used to describe the activity-temperature data for carbon in iron in both the aus-tenitic and ferritic phases. Darken&apos;s model takes into account only first neighbor pair interactions. For our needs, all neighbor pairs need to be taken into account. It is convenient to generalize Darken&apos;s model. The result for the partition function for austenite is: over the temperature range 800" to 1200°C and where the uncertainty corresponds to one standard deviation. Eq. [4] effectively yields only one relation. Another relation is required to obtain unique values for A and $. One property of Eq. [4] is that it is independent of crystal structure. Hence, data for a iron can be used to obtain another relation. To arrive at this relation we must generalize Eqs. [2] and [3] so that they may be applied to the bcc a iron. The result is that:

Jan 1, 1969

By J. S. Bryner

In the study of metallographic specimens in the electron microscope, there is need for a method of locating the same field in both the light microscope and the electron microscope. This need arises chiefly from the fact that in the electron microscope the magnification and degree of resolution are so much higher, and the field so much smaller than in the light rnicroscope that it is often difficult, if not impossible, to identify positively what is being observed. The difficulty is increased by the fact that, because a transparent film replica of the metal surface must be used in the electron microscope, micro-constituents can be identified not by their color but only by their texture and contours. For these reasons it is desirable to obtain a series of photographs showing the same field in both microscopes in order that the appearance of common microstructures and micro-constituents in the electron microscope may be identified and catalogued for future reference. The need for a method of locating the same field in both microscopes arises also when it becomes desirable to enlarge in the electron microscope for more detailed study a particular interesting structure observed in the light microscope. Using the standard polystyrene-silicalJ replica technique, in which the silica film replica is fished from the ethyl bromide on a 1/8 in. diam zoo-mesh specimen screen, the possibilities of locating a particular area on the film in the electron microscope are rather remote. The desired structure may be obscured by the wires of the specimen screen or unrecognizable at the high magnification. A solution to the problem would be provided if a specially designed specimen screen, containing an opening which could be absolutely identified and quickly located in the electron microscope, could be fastened to the silica film replica in such a position that the desired field on the specimen would be located at the identifiable opening in the specimen screen. The design for such a specimen screen, a method for producing it, and a technique for fastening it to the silica film replica are described below. Description OF Method The Specimen Screen A simple design for a specimen screen containing an opening easy to identify and locate in the electron microscope is one with two lines of openings at right angles in the form of a cross. Such a screen is shown in Fig I. The opening at the center of the cross is identified easily and can be located quickly in the light microscope and in the objective image of the electron microscope. The specially designed specimen screens for this work were produced in quantity by electroforming. On both sides of a polished strip of copper I X 3 X 1/8 in., twenty patterns of the cross of openings were punched with a diamond point micro-hardness tester, using a load of magnitude

Jan 1, 1949

By B. M. Larsen, K. Heindlhofer

THIS paper describes a relatively simple electrical apparatus that, through the close analogy between the flow of heat and of electricity, enables one to solve quickly and with satisfactory accuracy many complex problems in heat flow. This device, developed in 1935, has proved especially useful in the solution of certain practical problems relating to the design and efficiency of regenerators for an open-hearth furnace or coke oven, yielding within a few hours information that would take weeks or even months to acquire by mathematical1.2 or experimental3 methods of comparable accuracy. Its description now is prompted by growing interest in such analogues, as shown by several recent papers.4.5 The analogy between flow of heat and of electricity appears to have been recognized first by Maxwell who, in his famous Treatise on Electricity and Magnetism (1881) says: The analogy between the theory of the conduction of electricity and that of the conduction of heat is at first sight almost complete. If we can take two systems geometrically similar, and such that the conductivity. for heat at any part of the first is proportional to the conductivity for electricity at-the corresponding part of the second, and if we also make the temperature of any part of the first proportional to the electric potential at the corresponding point of the second, then the flow of heat across any area of the first will be proportional to the flow of electricity across the corresponding area of the second. .. Thus, in the illustration we have given, in which flow of electricity corresponds to flow of heat, the electric potential to temperature, electricity tends to flow from places of high to places of low potential, exactly as heat tends to flow from places of high to places of low. temperature He noted, however, that this analogy is restricted: ... there is, however, one remarkable difference between the phenomena of electricity and those of heat. Suspend a conducting body within a closed conducting vessel by a silk thread, and charge the vessel with electricity. The potential of the vessel and of all within it will be instantly raised, but however long and however powerfully the vessel be electrified, and whether the body within be allowed to come in contact with the vessel, or not, no signs of electrification will appear within the vessel, nor will the body within show any electrical effect when taken out. But if the vessel is raised to a high temperature, the body within will rise to the same temperature, but only after a considerable time, and if it is then taken out it will be found hot, and will remain so till it has continued to emit heat for some time. The difference between the phenomena consists in the fact that bodies are capable of absorbing and emitting heat, whereas they have no corresponding property with respect to electricity. According to this statement the application of the analogy would be limited to problems of steady flow that do not involve heat-capacity effects. In spite of this

Jan 1, 1945

By A. C. Heath, E. H. Dix

The importance of aluminum-silicon alloys in thc light alloy field is now generally recognized. Where silicon was once considered detrimental to the properties of aluminum, useful alloys now contain as much as 13 per cent. Furthermore, silicon is present as an impurity in aluminum of even the purest grades. Iron is another important impurity in aluminum and likc silicon is found in small quantities in the purest aluminum available today. The manner of occurrence of iron and silicon in commercially pure aluminum and many of its alloys exerts a very pronounced influence upon their properties. The effect of large quantities of iron in aluminum-silicon alloys is so detrimental that it has been found necessary to limit the allowable maximum percentage to as low a figure as is consistent with quantity production and satisfactory physical properties. The intimate relation existing between iron and silicon in aluminurn and alurninum alloys makes necessary a more complete knowledge of this ternary system. This paper is divided into two principal parts, dealing respectively with aluminum-silicon solubility equilibria and the constitution of aluminum-iron-silicon alloys. Part I.—Aluminum-silicon Alloys The early work on this system was largely confined to determining the general form of thc diagram and in this respect the results are in good agreement. Briefly, alulninunl and silicon form a simple eutectifcrous series without compounds. Until recently the solid solubility of silicon in aluminum had not been accurately determined. Ipraenkell (1908) stated that aluminum will retain 0.5 per cent. silicon in solid solu-t&apos;ion. Rosenhain, Archbutt and Hanson2 gave the maximum solubility as about 1.50 per cent. and added that "this solubility docs not appear

By D. L. McElroy

It is too broad a statement to say that the mine car is the most important unit in a haulage system, but almost every mining man will admit that it is one of the most important. The mine car is to the mine haulage system what the railroad car is to the railroads; the main purpose in each instance is to move the greatest number of ton-miles of material at the least cost. The data presented in this paper are taken from a study of mine haulage conducted by the School of Mines of West Virginia University at 42 mines in 8 coal fields of Wrest Virginia. The study was made possible by a graduate fellowship of the School of Mines and the cooperation of the mining companies of the state. Three important factors in the use of mine cars in West Virginia are: (I) the number of mine cars in use per loader; (2) the capacity of mine cars; (3) the distribution of mine cars. ("Loaders" in this paper refers to all men loading coal, whether manually or mechanically.) During the World War many mine managers were annoyed by the reduction of efficiency and production caused by railroad-car shortages. Today relatively little complaint is heard about a shortage of mine cars, yet possibly 50 to 75 per cent. of the mines in West Virginia are suffering from this cause of reduced production and increased costs. The railroads have solved their car shortage by placing in service more cars of larger capacity and better design. Many coal mines in West Virginia should solve a part of their cost problems by the same simple procedure. Such a procedure requires an initial outlay of capital, but there is little doubt that this will be repaid, with a good return on the investment. Determining Number of Cars Needed There can be no mathematical rule to determine the number of cars which should be in use per loader in a coal mine, because numerous factors such as concentration of mining, system of haulage, car capacity, speed of haulage, distance of working places from tipple, and so forth, affect materially the number of cars in use. These factors in turn are more or less determined by height of bed, character of roof and coal,

Jan 1, 1931

By E. A. Nesbitt

The important permanent-magnet alloys 15 years ago contained carbon and depended upon it for their permanent-magnet properties. In recent years great advances have been made in a number of new alloys substantially free of carbon. These include Remalloy,&apos; an alloy of iron, cobalt, and molybdenum, the various iron-nickel-aluminum alloys of the Mishima2 type, and the more recent Alnico V3 in which the best properties are developed by heat-treating in a magnetic field. The Mishima and the Alnico types of alloys are very brittle and after casting must be ground to size. This article describes a permanent-magnet material4 that can be machined as cast, and when handled with some care can be rolled to thin sheet and drawn to fine wire. Optimum magnetic properties are developed by a simple heat-treatment, and at this time the ductility of the alloy disappears. If the cast alloy is heat-treated without cold-working the mag netic energy product is about 1.0 X 106. This material is called Vicalloy I (pronounced vicalloy, V for vanadium, I for iron, and C for cobalt). When the alloy is first hot-worked and then considerably reduced in area by cold-swaging, drawing or grooved rolling, it is found that after heat-treatment the magnetic energy product measured in the direction of previous extension can be increased to 2.0 to 3.5 X 106. These higher values have been obtained only after reductions in area of 75 to 95 per cent, and since the material hardens considerably during working, the reduction ordinarily can be accomplished only in fine wires, although larger sizes can be reduced by the use of powerful machinery. When the material has been cold-worked in such a manner as to improve its energy product substantially, it is called Vicalloy 11. Commercial use of Vicalloy has been made in the recording of speech. Tape 0.002 by 0.050 in. has been found superior in quality to all others tried, and is now used in the Western Electric Mirrorphone 5 In a variety of forms Vicalloy I or I1 is useful in many laboratory instruments, and in experiments in which the sizes and shapes required cannot be obtained with the other more brittle permanent-magnet materials. In 1936, during a study of other age-hardening magnetic systems, it occurred to the author that some of the iron-cobalt-vanadium alloys might be suitable for permanent magnets. The proportions of iron, cobalt, and vanadium were varied and a range of alloys of particular interest was found, as shown by the indicated area in Fig. I. The limits of this range of composition are 30 to 52 per cent iron, 36 to 62 per cent cobalt, and 4 to 16 per cent vanadium. The compositions indicated by points outside this area were also tested. Preparation and Properties OF Vicalloy I The alloys were usually cast in graphite molds into bars 3/4 in. in diameter and

Jan 1, 1946

By E. A. Nesbitt

The important permanent-magnet alloys 15 years ago contained carbon and depended upon it for their permanent-magnet properties. In recent years great advances have been made in a number of new alloys substantially free of carbon. These include Remalloy,&apos; an alloy of iron, cobalt, and molybdenum, the various iron-nickel-aluminum alloys of the Mishima2 type, and the more recent Alnico V3 in which the best properties are developed by heat-treating in a magnetic field. The Mishima and the Alnico types of alloys are very brittle and after casting must be ground to size. This article describes a permanent-magnet material4 that can be machined as cast, and when handled with some care can be rolled to thin sheet and drawn to fine wire. Optimum magnetic properties are developed by a simple heat-treatment, and at this time the ductility of the alloy disappears. If the cast alloy is heat-treated without cold-working the mag netic energy product is about 1.0 X 106. This material is called Vicalloy I (pronounced vicalloy, V for vanadium, I for iron, and C for cobalt). When the alloy is first hot-worked and then considerably reduced in area by cold-swaging, drawing or grooved rolling, it is found that after heat-treatment the magnetic energy product measured in the direction of previous extension can be increased to 2.0 to 3.5 X 106. These higher values have been obtained only after reductions in area of 75 to 95 per cent, and since the material hardens considerably during working, the reduction ordinarily can be accomplished only in fine wires, although larger sizes can be reduced by the use of powerful machinery. When the material has been cold-worked in such a manner as to improve its energy product substantially, it is called Vicalloy 11. Commercial use of Vicalloy has been made in the recording of speech. Tape 0.002 by 0.050 in. has been found superior in quality to all others tried, and is now used in the Western Electric Mirrorphone 5 In a variety of forms Vicalloy I or I1 is useful in many laboratory instruments, and in experiments in which the sizes and shapes required cannot be obtained with the other more brittle permanent-magnet materials. In 1936, during a study of other age-hardening magnetic systems, it occurred to the author that some of the iron-cobalt-vanadium alloys might be suitable for permanent magnets. The proportions of iron, cobalt, and vanadium were varied and a range of alloys of particular interest was found, as shown by the indicated area in Fig. I. The limits of this range of composition are 30 to 52 per cent iron, 36 to 62 per cent cobalt, and 4 to 16 per cent vanadium. The compositions indicated by points outside this area were also tested. Preparation and Properties OF Vicalloy I The alloys were usually cast in graphite molds into bars 3/4 in. in diameter and

Jan 1, 1946

By Waldemar Lindgren

No one would maintain that all ore deposits or all deposits of useful minerals have been formed by the same processes. Generally they have originated by special processes of concentration but these may be of many different kinds. Some deposits have their origin in chemical or biochemical processes of concentration in rivers, lakes or seas, others developed on land by means of chemical reactions of surface waters on various forms of rocks. Certain insoluble substances remained behind; others were dissolved and precipitated in favorable places. This action proceeded in the realm of the oxidizing surface waters or in the deeper zones to which the waters from the surface could find their way. Examples of the latter kind may be found in the extensive copper and vanadium deposits of some sedimentary beds or in the lead and zinc deposits of certain broad limestone strata. In these instances the evidence for any other mode of origin would seem to be very weak indeed.&apos; Nor does it seem possible to deny that circulating waters may form deposits of the more common metals along fissures after having dissolved many constituents from paths traversed. Another very large class has been formed by magnetic processes of concentration. The last 40 years have been a period of intense activity in the investigation and description of a vast number of deposits; all modern methods have been employed and the result is an accumulation of data, difficult or impossible to master. It has been a period similar to that in petrography. The generalizations, the able deductions, have lagged behind. Evidently several geologists have become weary of this "infinite detail" and a mistrust of the microscope seems to have arisen. Although this feeling of being swamped in microscopic detail is a painful experience, nevertheless only through the detail in combination with the large features, and only by utilizing all the related sciences shall we

Jan 1, 1927

By Harry K. Ihrig

THE hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1/8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was, necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes Co. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.11 The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 DESCRIPTION OF TEST METHOD The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1945

By R. F. Mehl, C. S. Barrett, A. H. Geisler

THE mechanism by which the super-saturated solid solution of 20 per cent silver in aluminum decomposes has been reported in two previous publications. 1,2 The analysis of streaks in Laue photograms showed that thin platelike particles (the so-called Guinier-Preston aggregates) form upon {111} matrix planes in the early state of decomposition.1 The size of these particles is larger, the higher the temperature at which they form in accordance with nucleation theory;3 at all temperatures they increase in size with aging.2 When they have grown thick enough to afford three-dimensional diffraction, powder X-ray photograms show that the structure is not that of the equilibrium precipitate y but that of a transition lattice ?&apos;. Since this is also platelike in shape and also lies upon the {111} matrix planes with the {110} direction in the matrix parallel to the {11.0} direction in ?&apos;, it seems likely that the original platelet particles are merely ?&apos; in an early stage of formation, and thus finely dispersed. The atomic spacing and pattern on the {00.0} plane in ?&apos; are identical with those on the {111} matrix plane to which it lies parallel, and since comparable directions in the two planes are parallel, the lattices are thus coherent at the interface; an analogous coherence has been found in aluminum-copper alloys.3 The structures ?&apos; and y are both close-packed hexagonal and are oriented alike; they differ only in interatomic distances. Consequently, ? &apos; is regarded as y strained from its ordinary dimensions by the lattice coherency between it and the matrix.2 The lattice movements that transform the matrix to the equilibrium precipitate appear to be very simple.2 The mechanism of precipitation in this system is simpler and is more precisely known than that in any other system,2,4 hence the system should be a profitable one for the difficult task of correlating property changes with structural alterations. The present report provides additional studies on powder X-ray diffraction from alloys of 10 per cent, 20 per cent and 30 per cent Ag, and presents the correlation of crystallographic changes with changes in microstructure, Brinell hardness and electrical resistivity of the three alloys. PREPARATION OF SAMPLES AND EXPERIMENTAL PROCEDURE The preparation of the 20.2 per cent Ag alloy has been described.2 Alloys containing 9.9 and 29.7 per cent Ag were prepared from 99.97 per cent Al and 99.99+ per cent Ag using a similar procedure. Rolled

Jan 1, 1943

By Hugh H. Waesche

High quality quartz crystals weighing more than 50 grams are required in several important industrial applications.30,31 Primarily, they are the basic raw material for precision, electronic, frequency control components; this includes oscillators and filters in both radio and telephone services. Quartz crystals are also necessary for optical lenses and prisms in special applications requiring high ultraviolet light-transmission as in spectrographs. Quartz wedges are regular components for petrographic microscopes. The application of crystalline quartz as a transducer* in ultrasonic devices has increased in recent years despite strong competition from barium titanate and magnetostrictive [f] devices. Some quartz is fabricated into delay lines for radar. Man has valued quartz for fabrication of art objects since the dawn of history. The art forms were and are painstakingly carved and polished to form intricate figurines, bowls, statuettes, and the well-known crystal balls. The largest known ball, made of perfect quartz from Burma, is now in the National Museum in Washington. It is 12 7/8 in. in diameter and weighs 106 lb 12 oz. Clear, pure quartz chips and small crystals not meeting the electronic-grade dimensional requirements are known by the Brazilian term lasca. They are used to produce fused quartz having wide application in laboratory equipment, as special glasses, for torsion suspension in scientific instruments, and as a source material for growing large artificial quartz crystals 18,35 Electronic applications far exceed all other uses in importance so any discussion of high-quality quartz crystals must be concerned almost exclusively with those functions. Historical Background Because of their ubiquitous character and natural beauty, quartz crystals have long been of interest and known to man. They have been found among early Egyptian and Chinese art forms and the Sumerians are believed to have fashioned seals, beads, and other jewelry from quartz crystals, perhaps 5,000 years ago. Also, American Indians made arrow heads and fashioned some simple objects of different kinds. The origin of the name quartz, although of Greek derivation, is uncertain. The Greeks appropriately applied their word for frozen water or ice, krustallos, to quartz. The present-day, large-scale practical applications of quartz crystals began in 1880-1881 when Pierre and Jacques Curie reported discovery of the "piezoelectric" effect. They found this effect first in Rochelle salt, a common product of grape-wine refineries, while studying crystal symmetry. Piezoelectricity is that property found in certain crystals, including quartz, whereby electrical charges of equal and opposite sign appear on opposite parts of the crystals when they are stressed. If equal and opposite forces are applied to two opposing prism edges of a single untwinned quartz crystal a positive electrical charge will appear on one edge and a negative charge on the other. The amount of the charges will be directly proportional to the force applied. This property seems to be intimately related to pyroelectricity

Jan 1, 1960

By Ernest R. Darby

If the correct balance between fuel and air is maintained in an open-flame furnace,&apos; little chemical action may be expected between the products of combustion and the metal being melted. Physical&apos; changes in the metal are the object of the melting operation, and indirectly, under certain conditions, may be the cause of subsequent chemical actions. If sufficient heat has been introduced into the metal to bring about the change from the solid phase to the liquid phase, and still further from the liquid to the vapor phase, the metal vapor in all probability will be carried from the furnace by the exhaust and rapidly combined with the oxygen of the outside air. The charge being melted in the furnace may contain elements which are chemically inactive at normal temperatures but which will form compounds at the elevated temperatures of the metal bath, or even at a lower degree. Such indirect chemical actions are very confusing and often lead to incorrect conclusions regarding furnace atmospheres. In the open-flame furnaces used in the melting of bronze, the furnace atmosphere is spoken of as being either neutral, oxidizing or reducing in its effect upon the metal. A neutral atmosphere, as mentioned, is generally considered as the atmosphere of the furnace that will produce melted bronze, neither oxidized nor gassed. It is in effect an atmosphere which is not directly the cause of any chemical action. In such an atmosphere absolutely pure metals may be melted and poured without the absorption of gases or the formation of metallic oxide. The metal has undergone a simple, physical change. An oxidizing atmosphere is one in which the air introduced to the furnace is in excess of that required to complete combustion of the fuel used. The oxygen of the excess air may combine with the metal being melted to form metallic oxide, which may or may not be dissolved by the metal. If an absolutely pure metal is melted in a furnace operating with such an atmosphere, a portion of the metal charged may be converted into metallic oxide, the amount depending upon the duration of the

Jan 1, 1930

By W. A. Krivsky, R. Schuhmann

PREVIOUS papers in this series on the thermo-•t dynamics of copper-smelting systems have presented a survey of the field and an outline of the overall program: thermodynamic studies of iron silicate slags, 2-4 and thermodynamic data for simple mattes in the Cu-S system.5 Since this program was started, an excellent summary of the whole field of physical chemistry of copper smelting was published by Ruddle. The present paper represents a further step in the study of liquid mattes, and deals specifically with the Cu-Fe-S system. The importance of the Cu-Fe-S system to copper smelting is evident from the fact that these three elements constitute 90 to 99 pct of the totalweight of most commercial mattes. In copper mattes oxygen is an important fourth component. Oxygen was rigorously excluded in the work to be described in this paper. However, the behavior of oxygen in mattes was the subject of a companion research by Lander&apos; which will be described in a subsequent publication. Several studies have been made previously of phase equilibria in the Cu-Fe-S system,8-10 so that the ternary phase diagram is fairly well established in most regions. Also, separate studies have been made of the phase diagrams and thermodynamic properties for the three binary systems: CU-S,5,12-15 CU-Fe,11,14,17 and FeS.11,14,16,17 However, no work has

Jan 1, 1958

By J. G. Koenigsberger

The electrical specific resistance of rocks in the field is measured by sending a current through a medium of great volume, compared to the electrodes, whose resistivity should be measured. The whole resistance can be determined by the Wheatstone bridge and the specific resistance calculated by a well-known formula. The resistivity of some rocks in place in Germany and in Switzerland is given; first, of a rock near the surface, and especially near electrodes. Practical applications are made in the determination: (1) of the continuity of a conducting orebody; (2) of the surface ares of an orebody; (3) in the detection of a water-bearing fault in a salt mine. Preliminary &apos;observations are described: (1) on the influence of the depth of ground-water table; (2) on the detection of gas under high pressure in coal seams. The observations in this paper of the electrical resistivity of rocks and soil in place are along the lines of the very interesting method and results of the Messrs. Gish, Rooney, Hotchkiss and Fisher. 1,2 All the work described has been done since 1920. Method Used The very simple method consists in the application to the rock of two plane circular electrodes of iron or brass of a suitable diameter, with the aid of a contact substance, and in measuring the resistivity in a Wheatstone bridge with alternating current of 100 to 400 Hertz frequency per sec.). The general formula is known to be R= R0 +d/4(1/a+1/b-1.7/l+0.8(a+b)/l2) (1)

Jan 1, 1929

By Henry A. Stiff

The classification and correlation of water analysis data presents many problems which can be solved by graphic methocis. The pattern system, a new type of graphic procedure described in this communication, is believed to have several advantages over older methods. Examples of the application, of the pattern system to the solution of problems encountered in petroleum production are given. INTRODUCTION Several graphic methods for presenting analytical water data have been developed and are now in use.1,2,3,4 It is believed, however, that a recently developed type of graph called the "pattern" offers several advantages over other methods. This system presents a better picture of the total salt concentration than is usual in such graphs. The effect of dilution or concentration has been reduced to a minimum, and at the same time distinction between various types of water has been improved. The system is extremely versatile, yet so simple it can be plotted on ordinary graph paper and adapted to almost any type of filing system. DISCUSSION The essential feature of the pattern system is the graph shown in Fig. 1. Horizontal lines extending right and left from a vertical line at zero form the graph. Positive ions are plotted to the left while negative ions are plotted to the right. The figure immediately beneath each ion gives the scale. Most oil field waters can be plotted on a scale where 100 milli-equivalents of sodium and chloride and 10 milliequivalents of each of the other ions are represented by one scale unit. For highly concentrated brines, 1,000 milliequivalents of sodium and chloride and 100 milliequivalents of each of the

Jan 1, 1951

By Henry A. Stiff

The classification and correlation of water analysis data presents many problems which can be solved by graphic methocis. The pattern system, a new type of graphic procedure described in this communication, is believed to have several advantages over older methods. Examples of the application, of the pattern system to the solution of problems encountered in petroleum production are given. INTRODUCTION Several graphic methods for presenting analytical water data have been developed and are now in use.1,2,3,4 It is believed, however, that a recently developed type of graph called the "pattern" offers several advantages over other methods. This system presents a better picture of the total salt concentration than is usual in such graphs. The effect of dilution or concentration has been reduced to a minimum, and at the same time distinction between various types of water has been improved. The system is extremely versatile, yet so simple it can be plotted on ordinary graph paper and adapted to almost any type of filing system. DISCUSSION The essential feature of the pattern system is the graph shown in Fig. 1. Horizontal lines extending right and left from a vertical line at zero form the graph. Positive ions are plotted to the left while negative ions are plotted to the right. The figure immediately beneath each ion gives the scale. Most oil field waters can be plotted on a scale where 100 milli-equivalents of sodium and chloride and 10 milliequivalents of each of the other ions are represented by one scale unit. For highly concentrated brines, 1,000 milliequivalents of sodium and chloride and 100 milliequivalents of each of the

Jan 1, 1951

By J. W. JESSUH

TO certain people the name of Northern Rhodesia brings only a vague recollection of a distant country somewhere in Africa; to others, it means a big game territory and the opportunity for excellent shooting; to some, a land of sunshine and peace; but to mining men the name signifies the land where the latest discoveries of copper ore are astonishing the mining world and bid fair, in a few years, to make Northern Rhodesia one of the largest copper- producing countries. There is a fascination about this part of the globe that is somewhat similar to southern California, and at the same time there is that feeling of mystery peculiar to a tropical climate. Perhaps it is the isolation, the fear of wild animals, or the influence of an undefinable something which cannot be expressed.

Jan 1, 1931

By T. E. Kihlgren

SYSTEMATIC data are presented on the relation of composition of nickel silvers to color, tarnish resistance, hardness and liquidus temperatures, for alloys containing up to 30 per cent nickel and 50 per cent zinc, further modified at certain nickel and zinc contents by 0 to 8 per cent of tin and 0 to 10 per cent of lead. Attention has also been directed, using a still more limited range of alloys, toward a study of tensile properties and such casting properties and characteristics as fluidity, shrinkage and pressure tightness. In some of these, rather broad ranges of composition are dealt with; in others, it has been expedient to focus attention on the Federal Specification 20 per cent nickel silver casting alloy, WWP-541. INTRODUCTION The demand for an alloy essentially white in color, which could be cast and worked by simple methods and which possessed strength and corrosion-resisting properties superior to the usual brasses, led to the discovery and early use of cupronickel alloys containing zinc, and some-times tin, lead and other metals. This type of alloy was generally known as German silver until the war, when the term "Nickel Silver" became generally accepted. The element principally responsible for the white color of the alloy and for its strength and corrosion resistance is nickel, which may constitute from 8 to 30 per cent of the alloy. The functions of the other elements will be described later. The manifold uses of nickel silver are largely due to its color, corrosion resistance, ease of casting, fabrication, joining and rather moderate cost. In many instances the alloy is finished by grinding and polishing while in others it may be finished with a silver or nickel plus chromium plate. Electroplates

Jan 1, 1935