Search Documents

By Juhani Pulkkinen, Pekka Lappalainen

Preplaced cable bolts - fully grouted old hoisting cables or stress relieved steel strands - have been used succesfully to pre- reinforce ore contact zones and pillars in sublevel stoping at Outo- kumpu Oy mines for ten years. The purpose is to make open stoping methods possible even in "poor'' conditions and to decrease waste rock dilution. Since 1971 more than 120 km cable bolting has been done, and plans for this year in five mines amount to 33 km. In order to understand the function of cable bolt, pull-out tests have been done both in the laboratory and in situ. Bond strength between cable and cement is highly dependent on cable structure and cable surface dirtiness. Steel cables with steel core and rough surface structure have highest bond strength ( 6 MP~). A cable bolt is a friction bolt. After losing its peak bond strength - after starting to move - a cable bolt still has a high loading capacity due to the friction caused by the uneven surface of the cable. Cable bolting is done before actual stoping from existing drifts, sublevel drifts, e.g. or from special bolting drifts. In general stress relieved steel strands are used; 2 x 15.2 mm dia per hole. FEM or BEM calculation is utilized in cable bolting design. Bolts 2 are in fan shape, 10 m ... 50 m long and are spaced 1/20 m ... 1/50 m2 at stope walls. Pretensioning of cable is not needed, when bolting is done before rock deformations. Bolting costs vary between 0.3 USD ... 1.0 USD/ore ton. In the beginning only manual cable installing technique bras used. Now bolting can be done as fully mechanized with the developed cable bolting machine; i.e. drilling of the hole, installing and cutting of cables and grouting of hole.

Jan 1, 1983

By K. Tanaka, J. D. Mote, J. E. Dorn

It) an attempt to ulLcoce.lP the operative strain-rate-contl-olliy: dislocation nieclzanistns, specially oviented sizgle clystals of the intel-nzediate 1zexagonal phase containing Ag plus 33 at. pct A1 were tested in tension over a wide range of temperatures. Slip was observed to take place by the {0001} <1120> {l100} mechani fracture took place across the(i100) plane and winning occurred by the (i01Z) ?lechanisn. Basal slip exhibited a strong yield point over the -alzge from 77 to 450°K, the upper ,esolved shear st]-ess having the exceptionally high value of 10,500 psi over this entire ?-a?zge of tenzpei,atuves. The critical 9-esolved shear stress for prismatic slip decreased f7-om 48,000 psi at 4.3"K to 23,000 psi at 170°K (Region 1) follozcirg zt:lzich it decl>eased sloz&ly to 21,500 psi at 475°K (Res&apos;on II); from 475" to 575°K (Regioz III), the c7-itical esolced shear stress dec&apos;-eased precipitously to 2000 psi; and from 575" to 750°K (Region IV) it decreased less afi&apos;dly to a low value of about 500 psi. Pvistintic slip in Region I was pobably controlled by the tliel-nally activated riecharzisui of nucleation and g,-ozcth of kinks in dislocations lying in Peierls potential troughs. In Region II for prismatic slip the critical 1-esolved shear stress was slzocn to be deteemined by sh0l.t-range 01-dering, Overall the forgiorz fo basal slip, 7.c.lre1-e a Strong yield-point phenorlienu ia7as observed, the critical vesolved slzea?-stress was shoztn to be determined by n conibirzation 0-f Szizuki locking and short-range-order Izavderzizg, The precipitous decrease in the critical resolved shear stress with increase in ter,/pe7-atrir-e over Region HI was tentatively ascribed to a decrease in the degree of slort-)ange 07-del;iqq (0)- clusteing) and also the effect of fluctuations the degree of o?der, It is at pgreser2t zrtzce)taitz as to 1t1hethe1- these or other possi1)le effects are also ,esponsible. fo- the data obsel-ved 172 Region IV. 1NTEREST in inter metallic compounds stems not only from their role in dispersion hardening of polyphase alloy ystems but equally from their potentialities for high strength, hardness, and stability not only at atmospheric temperatures but especially at elevated temperatures. As summarized in a re- cent symposium of the Electrochemical Society on "Mechanical Properties of Inter metallic Compound", most of the experimental evidence regarding the mechanical behavior of intermetallic compounds centers about the effect of temperature on the hardness and ductility of polycrystalline specimens. The available data reveal that the plastic behavior of intermetallic compounds might be rationalized in terms of the usual dislocation mechanisms appropriate to a solid solutions providing the additional complexities arising from crystal structure, long-range ordering, short-range ordering, and defect lattices are taken into consideration. It is apparent, however, in terms of the history on a solid solutions, that a complete detailed mechanistic rationalization of dislocation processes may not be possible until the deformation processes are studied in single crystals of intermetallic compounds. The present paper contains a preliminary report on the plastic behavior of single crystals of the hexagonal Ag-A1 intermetallic phase over a wide range of temperatures. The results confirm the thesis that single crystal data provide a most effective method of identifying operative dislocation mechanisms in intermetallic compounds. EXPERIMENTAL TECHNIQUES Several factors prompted the selection of the hexagonal Ag-A1 intermetallic phase for this preliminar investigation on the plastic properties of single crystals of intermetallic compounds: 1) This phase has a wide solubility range5 which would permit future investigations on the effect of composition and axial ratios on slip mechanisms. 2) Although it undoubtedly exhibits short-range ordering (or clustering) this intermetallic phase is free from complexities arising from long-range ordering.6 3) Since the atomic radii of aluminum and silver are practically identical, the possible complications due to Cottrell locking are minimized. 4)Whereas the dislocations on the basal planes are expected to dissociate into Shockley partials and are thus susceptible to Suzuki locking, those on the prismatic planes probably remain complete. 5) The axial ratio, being 1.61, is almost ideal, suggesting that short-range ordering may be almost spherically symmetrical. The present investigation was conducted exclusively with the hexagonal Ag-A1 alloy containing 33 at. pct Al. Preliminary investigations revealed that this alloy undergoes basal slip by the (0001)

Jan 1, 1962

By L. O. Howard

TWO or three years ago there were submitted to me some reports of tests that had been made on a semi-oxidized ore of silver looking to its treat-ment by combined flotation and cyanidation, together with a sample of the ore, with a request that I check the tests and confirm them, if possible. These tests had been made by a machinery-supply house and with them was a flow-sheet for a proposed mill, with full details of equipment to be used in the mill. The limited data on which this was based at once attracted my attention and have caused me from time to time to put various groups of students at work to develop simpler methods of obtaining data, which it appeared should be at hand and could be obtained by simple tests before attempting to treat these ores commercially. A brief discussion of the working out of such methods may be of interest and may contribute somewhat to the de-velopment of better testing methods for the small operator who has not at his command a staff of metallurgists. Of several tests on samples of varying assay and mineralogical composition, by cyanidation alone, by flotation alone, and, by combinations of the two, the following report was perhaps the most complete and may well serve as a typical example: METALLURGICAL TEST REPORT Silver Mines Co. Semi-oxidized Ore Procedure: Ore ground to 65 mesh, given flotation treat-ment using pine oil and potassium xanthate. Flotation tailing was thickened and given cyaniding agitation in solution strength of 5 lb. cyanide per ton and 2 lb. lime per ton.

Jan 12, 1927

INTRODUCTION Great emphasis has been given throughout this text to the necessity of maintaining the integrity of mineralogical populations when operating upon sample data drawn from mixed populations. Mineral deposits rarely are completely homogeneous and often consist of many subsets separated by geological and mineralogical boundaries. Sometimes different mineral populations are difficult to distinguish, and may be inadvertently lumped together-often without serious consequences, but more often with detrimental effects upon analytical results. The geologist must accept the responsibility for recognizing and recording mineral boundaries that may include: changes in mineral suites, lithological horizons, host rock types, faulted and offset segments, zones of enrichment or depletion, and several other geological and mineralogical changes that effect mineralogical structuring and distribution within a deposit. When employing conventional methods for assigning estimated values to irregularly shaped mineral inventory blocks, it was only necessary for the geologist or engineer to con- fine the block limits to the known geologic boundaries. Thus if a fault interrupted the mineral zone, the trace of the fault could be used as a block boundary. Intelligent decisions could always be made as to which blocks to include in each mineral population. However, with the advent of the computer, which per- mits the computation of mineral inventory blocks using better mathematical estimation techniques, there now enters the "boundary problem." Unless the computer can be programmed to recognize population differences and geologic boundaries, greater estimation errors will be found in computer-generated mineral reserves rather than in less sophisticated conventional inventories. Much disillusionment has been expressed over the years by experienced mineral appraisers as a result of their study of computer-generated inventories that failed to account adequately for geologic vagaries. Many, thus disillusioned, have concluded that computer techniques are not satisfactory, or have only limited applications to simple deposits. As with all problems in the mineral industry,

Jan 1, 1980

By C. F. Weinaug, P. M. Blair

Many difference equations used to approximate reservoir flow problems treat the phase pressures implicitly but not the mobility-density coefficients. Such difference equations are neither wholly explicit nor implicit, but might be described as mixed. Mixed equations are relatively easy to apply. But the associated time truncation error is relatively large, and when used to solve problems characterized by high flow rates, these equations may be unstable for practical size time steps. This paper outlines the development of a completely implicit difference analogue for reservoir simulation, along with a Newtonian iterative method for solving the resulting nonlinear set of algebraic equations that arise at each time step. While this implicit equation requires two to three times more work than does the mixed equation, it is shown to markedly decrease the time truncation error and to yield a stable solution for much larger time steps than does the mixed equation. INTRODUCTION Calculation of multiphase, multidimensional flow in porous media is generally accomplished by numerical methods that involve approximating systems of partial differential equations by systems of partial difference equations. The early development of difference equation techniques was directed toward the solution of linear differential systems. However, the equations of multiphase fluid flow through porous media are highly nonlinear in that mobility and density often are strong functions of pressure and saturation. Thus, solution of the flow problems by difference equations involves solving sets of algebraic equations whose coefficients change from step to step of the calculations. Current practice is to evaluate most coefficients at the beginning of a time step and then to apply difference methods well suited for solving linear problems. At least two major difficulties arise from the use of this practice. First, evaluation of coefficients at the old time level and evaluation of pressures at the new time level results in larger time truncation errors near displacement fronts than if all quantities in the distance derivative were evaluated at the same time level. Second, evaluation of mobility coefficients at old time levels results in an unstable difference equation in regions of high flow rate. The first of these difficulties often results in optimistic recovery behind the displacement front, and the second requires the use of small time steps or special techniques in solving coning problems1 or problems of gas percolation.2 Evaluation of all quantities in the distance differences at the new time level results in a completely implicit difference system. Such a difference system has a lower time truncation error than equations in which mobilities are evaluated at the old level and pressures evaluated at the new level. The algebraic equations resulting from the fully implicit difference equation are, in this case, nonlinear and require some iterative method for their solution. This paper develops fully implicit difference equations for two-phase flow in porous media, describes their solution by Newtonian iteration, and gives examples of problems more easily solved by the new method than by previous methods. EVOLUTION OF DIFFERENCE EQUATIONS FOR NONLINEAR PROCESSES The completely implicit difference equation used in these calculations results from evolution beginning with explicit difference equations, proceeding through what we will call "mixed" equations, and arriving now at a completely implicit equation. Let us illustrate the evolution by considering different analogs of the nonlinear equation

Jan 1, 1970

By Clark Millison

The core recorder, a mechanical instr-ent for determining the exact depth at which core is recovered, drilled up or lost, is described. Examples of charts from the recorder are explained and interpreted. The uses of the core recorder are discussed. INTRODUCTION In the experience of geologists and engineers during coring operations on drilling wells, many will recall the times when a full core was not recovered and particularly when the requirement was urgent that they know exactly what part of the core was lost. To make this determination, the core recorder was designed. Its uses are many, and only the most obvious will be presented here. Although this discussion will be limited to drilling wells for petroleum, the core recorder can be used in any type of coring operation. The principle of the core recorder is the proportional reduction of the motion of core entering or dropping out of the core barrel to a stylus moving in such a manner as to record the reduced motion on a chart. The time element is registered on the same chart by the revolution of a clock which turns the chart drum. Thus the exact amount of core entering or dropping out of the core barrel is charted and the time of such entry or exit from the core barrel is precisely correlated to the depth at which the core is recovered or lost. Lack of movement of the stylus which is revealed by the continued revolution of the chart drum indicates that no core is entering the barrel. The principles are accomplished by an instrument placed inside of the core barrel. A cylinder which contains the clock and mechanical apparatus has a diameter smaller than that of the core barrel. Near the top of the cylinder is an eighteen hour clock which turns the drum that contains the chart. Near the bottom of the instrument is a serrated wheel which by friction against the inside of the core barrel is turned as core enters or drops out of the barrel.

Jan 1, 1949

By Clark Millison

The core recorder, a mechanical instr-ent for determining the exact depth at which core is recovered, drilled up or lost, is described. Examples of charts from the recorder are explained and interpreted. The uses of the core recorder are discussed. INTRODUCTION In the experience of geologists and engineers during coring operations on drilling wells, many will recall the times when a full core was not recovered and particularly when the requirement was urgent that they know exactly what part of the core was lost. To make this determination, the core recorder was designed. Its uses are many, and only the most obvious will be presented here. Although this discussion will be limited to drilling wells for petroleum, the core recorder can be used in any type of coring operation. The principle of the core recorder is the proportional reduction of the motion of core entering or dropping out of the core barrel to a stylus moving in such a manner as to record the reduced motion on a chart. The time element is registered on the same chart by the revolution of a clock which turns the chart drum. Thus the exact amount of core entering or dropping out of the core barrel is charted and the time of such entry or exit from the core barrel is precisely correlated to the depth at which the core is recovered or lost. Lack of movement of the stylus which is revealed by the continued revolution of the chart drum indicates that no core is entering the barrel. The principles are accomplished by an instrument placed inside of the core barrel. A cylinder which contains the clock and mechanical apparatus has a diameter smaller than that of the core barrel. Near the top of the cylinder is an eighteen hour clock which turns the drum that contains the chart. Near the bottom of the instrument is a serrated wheel which by friction against the inside of the core barrel is turned as core enters or drops out of the barrel.

Jan 1, 1949

By B. C. Allen

The solubility of chromium in liquid silver and that of molybdenum and tungsten in liquid tin have been determined by equilibrating Ike Liquid in a crucible of the solule metal. Generally the weight of solute in solulion was delermined both chemically and from crucible weight losses. The resulting weight percent solubilily of chromium in silver as a function of absolule temperature T is given by log w = -6660/T + 4.02 in the range 960° to 1445°C, and that of molybdenlttrl in tin by log w = —5050/T + 1. 79 in the range 1200° to 2200°C. The values appear unaffected by minor changes in solute composition. Calculations aye made of the parlial molar heal and excess entropy of mixing. The estimated solubility of tungsten in tin is 0.001 pct at 2000°C. Evidence is presented that molybdenwm dissolves in tin without compound for mation and that tungsten and tin form W10Sn. RECENT developments in coatings, heat transfer, and brazing require a knowledge of equilibrium solubilities in a variety of systems at elevated temperatures. Of particular interest are solid-liquid interactions in metal systems involving dilute solutions. This investigation was undertaken since little is known about the phase relations or solubility of chromium in liquid silver or of molybdenum and tungsten in liquid tin.1,2 EXPERIMENTAL WORK As indicated in Table I, high-purity metals or those of known impurity levels were used. Crucibles were machined from chromium, molybdenum, and tungsten bar stock 1.3 cm diam and 2.2 cm long. Chromium rod was prepared by arc melting and extruding iodide process crystals.3 The five chromium impurity alloys were in the form of 0.6-cm-diam swaged rod. A Cr-0.06N* alloy was prepared by exposure to NH3 at 1150°C in a closed quartz capsule for 24 hr. Because significant nitrogen was lost during annealing in argon at 1600°C,4 the estimated level was 0.01 pct N. Chromium and Mo,W crucibles were outgassed at 1200" and 1600°C, respectively, at 3 X 10-5 mm. The solvent was placed In crucibles of the solute metal- 6 g Ag in chromium, 0.4 g Ag in the five chromium impurity alloys, and 4 g Sn in Mo,W crucibles. The silver and tin series were outgassed at 900" and 110O°C, respectively, and held at the desired solution temperature in a tantalum resistance furnace under 1.05 atm 99.995 pct Ar. An equilibration time of 0.5 to 1 hr was chosen since 0.3-, I-, and 4-hr anneals at 1235°C for Cr-Ag yielded similar results. Temperatures were measured optically to +10°C under essentially black body conditions which were checked against the melting point of silver. The Cr-Ag and Mo-Sn,W-Sn series were respectively equilibrated at 990° to 1400°C and 1200" to 2000°C. Vaporization losses were generally held to <1 pct by the argon. In the 1800" and 2000°C anneals for 0.5 hr, the crucibles were placed in tightly sealed tantalum cans which kept tin losses to <5 pct. After the anneals, the specimens were furnace-cooled. One anneal was made on small Mo-0.02 C, Mo-0.5Ti-0.lZr, and tungsten crucibles containing tin at 2200°C. The metals were sealed in an electron-beam-welded tantalum can of minimum volume. After the anneal, tin was still present in each crucible, none of which was severely attacked. After equilibration, the saturated solvent metal was selectively removed from the crucible by acid leaching. Weight losses sustained by the crucibles were determined from the initial weight minus the final blank-corrected weight after acid leaching. Chemical analyses were performed on some of the samples. Hot 1:l HNO3-H2O removed silver from chromium with the blank running <0.1 mg or <0.002 pct on measured solubility. Tin was removed from molybdenum and tungsten by hot concentrated HC1 with the respective blanks amounting to -0.004 and -0.0004 pct in the presence of tin. The insoluble residues were weighed and checked for composition. The leaching solutions contained traces of the solute metals which were analyzed by colorimetric methods, Diphenyl Carbazide for chromium, Thiocyanate for molybdenum, and Dithiol for tungsten. The total of the two percentages found from the residue and leaching solution minus the blank gave the desired solubility values. On the basis of annealing empty molybdenum and tungsten crucibles, weight losses due to MoO3 or WO3 volatilization were found to be generally 10.4 mg and affect measured solubilities by <0.01pct. RESULTS AND DISCUSSION Chromium-Silver . Since no intermediate compounds are reported to form in the Cr-An system,&apos; crucible weight losses and chemical analysis of the entire melt should provide reliable measures of the chromium in solution. Values obtained by the two methods are in agreement as shown by the results for unalloyed chromium in Table II and plotted in Fig. 1. Furthermore, the results are consistent with those previously determined by melting equilibrated silver out of the crucible and analyzing calorimetrically for chromium.&apos; On the basis of limited thermal analysis data, the solubility of chromium in silver has been quoted as 8 pct at the monotectic temperature of -1445°C.1 This investigation indicates an extrapolated solubility of 1.38 pct which is believed to be more reliable. At the eu-

Jan 1, 1968

Arizona ROBERT W. THOMAS, Chairman &apos;ROBERT W. HUGHES, Vice-Chairman HUBERT O. WOODS, Secretary-Treasurer American Smelting & Refining Co., Hayden, Ariz. FRANK A, WARDLAW, JR., National Director THOMAS C. CHAPMAN P. D. I. HONEYMAN CARL H. COLE JOHN E. LANNING. JOHN H. DAVIS JOHN C. LOVING EDW. G. DENTZER ALBERT MENDELSOHN MORRIS G. FOWLER BRENT N. RICKARD H. C. HENRIECHARLES F. WILLIS Black Hills BANCROFT GORE, Chairman N. P. GOODRICH, First Vice-Chairman C. N. KRAVIG, Second Vice-Chairman C E. SCHMIDT,

Jan 1, 1941

By L. S. Birks

The bainite transformation in a 3.5 pct Ni-1.25 pct Cr steel was studied under various conditions of cooling and stress. Several characteristics may be specified: 1) transformation in the bainite region (925° to 575°F) is very little affected by the manner of cooling from the austenitizing temperature at 1600°F to 575°F)tothe upper limit of bainite transformation at 925°F; 2) starting time for the bainite transformation is the same order of magnitude for either isothermal transformation or continuous cooling, but the rate of transformation is somewhat greater for isothermal transformation; 3) tensile stress accelerates both isothermal and continuous cooling transformation, and 32,000 psi stress changes the form of the isothermal transformation diagram to correspond in appearance to the continuous cooling diagram; 4) transformation for nonlinear, continuous cooling may not be determined directly from the linear, continuous cooling transformation diagram, but may be predicted by assuming first that the fractional amount of austenite transformed in a given small temperature interval depends on the approximate linear cooling rate during that temperature interval and then by summing stepwise over the whole temperature range. IN a previous publication&apos; an X-ray spectrometer was described with which the X-ray diffraction from a specimen could be observed continuously under controlled temperature and tensile stress. This instrument has now been applied to a study of the austenite-bainite transformation in a Ni-Cr steel for both isothermal and continuous cooling conditions, with and without stress. Certain characteristics of the transformation lead to a method of predicting the amount of transformation to be expected at a given temperature for any type of cooling curve. Material and Specimen Preparation The steel chosen for the investigation was a Ni-Cr steel having the composition in the following percentages: 0.30 C, 0.27 Mn, 0.019 P and S, 3.50 Ni, and 1.25 Cr. In order to fabricate specimens suitable for the X-ray spectrometer, a 1/4 in. plate was ground down to 0.060 in. and then cold rolled to about 0.035 in. Next it was heat treated by quenching in oil from 1650°F and tempering at 1200°F for 1 hr. Then it was etched in dilute nitric acid to reduce its thickness to 0.014 in. and cut into blanks in the shape of flat tensile specimens 3 1/4 Vi in. long, 7/16 in. wide, with a notch % in. long and 7/32 in. wide; see Fig. 1. X-Ray Technique Since the X-ray spectrometer has been described in detail elsewhere,&apos; only a brief outline of the principles will be repeated here. A focusing, pow- der-diffraction arrangement&apos; was used, as shown schematically in Fig. 1, and the specimen was mounted vertically in a vacuum furnace (not shown in the figure). The X-rays, moving in a horizontal plane, enter and leave the furnace through beryllium windows. As shown in the figure, X-rays diverging from the line source A are diffracted by the specimen B and converge at the detector slit C. The detector D and the slit C may be set at the proper angle in the horizontal plane to receive X-rays diffracted by either the face-centered phase (austenite) or the body-centered form (ferrite, bainite, martensite). The specimen is heated by electrical conduction between connectors E, and E,, and a Pt—Pt-10 pct Rh thermocouple spot-welded to the center of the notched region on the side away from the X-ray beam indicates the temperature continuously on a Brown recorder. Temperature control is exercised manually with a variable transformer on the input to E,-E,. Any desired time-temperature relationship is easily obtained by first drawing the desired curve on the temperature recorder chart and then adjusting the variable transformer during the run so that the thermocouple

Jan 1, 1957

By C. L. Dake

Discussion of the paper of. C. L. DAKE, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 103, July, 1915, pp. 1429 to 1436. A. C. LAWSON, Berkeley, Cal.-It appears that our bog-iron ores are due in a large measure to the activity of certain iron bacteria, and a paper dealing with this subject that makes no reference to that particular agency strikes me as rather curious. C. L. DANE, Rolla, Mo.-Mr. Lawson&apos;s criticism that this paper makes no reference to the activity, of iron bacteria is scarcely true. On p. 1430 I stated: "Certain bacteria precipitate iron by building the hydrated oxide into their body cells," and again, "There are many other means by which, under special conditions, iron may be precipitated in nature. Oxidation, evaporation of CO2, and iron bacteria have been held to be the most important." Thus the activity of bacteria receives as extended mention as the action of any other agency in precipitation of iron. The paper makes no pretense of covering exhaustively the origin of bog ores, but, as its original title suggested, refers to Some Principles Controlling the Formation and Distribution of Bog Iron Ores. Mr. Lawson seems to have entirely missed the main thesis of the paper, which attempts to establish some relation between glaciation and abundance of bog ores now forming. Unfortunately, I have no immediate access to the literature of the subject, but my best recollection is that the data regarding iron bacteria throw no light whatever on the cause of bog ores being so much in ore abundant within the limits of the glaciated regions, and being reported much less frequently from the tropics. This lack of data is suggested in the following (p. 1434): "It has already been shown that bacteria aid in the precipitation of iron. Whether tropical conditions increase or decrease the activity of such bacteria is unknown."

Jan 12, 1915

By Earl E. Hunner

At the end of the year 1914, the main North Star incline shaft had reached the 6300-ft. level, and encountered a vein dipping southwest, or exactly opposite to the North Star. Subsequent development failed to find the North Star vein continuing beyond this intersection, so the 6300-ft. level proved to be the bottom level of the North Star vein, and very little ore was found below the 5300-ft. level. The new vein was called No. 1 vein. Development work carried on for the next 10 years discovered a third vein, called No. 2, branching off about 1200-ft. to the east, with a north-south strike and a west dip. No. 1 vein had about 900 ft. of backs above the 6300-ft. level before reaching the boundary line of the property, and No. 2 vein died out about 800 ft. above. During these 10 years, the money spent on development was increased from $54,000 in 1914 to $184,000 in 1924; the ore reserves steadily diminished until it was evident that the mine must close down unless by some means a large tonnage of ore could be developed quickly. Problems and Plans In order to understand what follows, the general layout and equipment of the mine as it was at this time must be briefly described. Fig. 6 indicates the relative positions of the shafts. The North Star (incline) shaft extends from the surface to the 6300-ft. level following the vein, with an average pitch of 26", between limits of 11" to 38. There is at present no hoisting equipment in this shaft between the 2700 and 4000-ft. levels. The Central (vertical) shaft connects with the North Star shaft at the 4000-ft. level, at a vertical depth of 1600 ft. In two compartments of this shaft 4-ton skips made a vertical turn of 15 ft. radius at the 4000-ft. level and ran down the incline to the 6300-ft. level. A cage operated in the third compartment to the 4000-ft. level. Men and supplies were transferred to a truck running on a third track down the incline shaft to the 6300, operated by an electric hoist on the 4000-ft. station. When the shifts changed double-deck cages were substituted for the skips in the vertical shaft, but they stopped at the 4000-ft. station. The truck to 6300 carried 22 men, and it required 8 min. to make a trip down and back. This arrangement was satisfactory as long as a fairly large proportion of the work was

Jan 1, 1930

By Henry J. Miller, Marcella Lindeman

DURING some experiments made by Henry J. Miller, partly in Germany and partly in the United States, in which it was found necessary to melt metals in quantities up to 60 kg. in a vacuum or under low pressures of hydrogen, molybdenum was tried as the resistor in the electric melting furnaces. Molybdenum ribbons 16 by 0.55 mm. and 18 by 0.45 mm. were used as resistors. The furnaces were of the type shown in Fig. 1. [ ] About the heating tube, Y, are wound parallel resistors of molybdenum ribbon from the water-cooled electrodes, E1, E2. The whole is within a copper container having outlets for the removal or introduction of gases and a window, W, for observation, the space about the heating tube and electrodes being filled with insulating material. The life of the molybdenum used as the resistor was found to depend very much on the manner of using it, its failure being due in some cases to thinning by evaporation or chemical reaction and in others to hardening, which prevented it from following the expansions and shrink¬ing of the heating tubing without cracking. As such failures are often rather expensive in commercial work, it was thought worth while to determine the causes. The factors influencing the behavior of molybdenum resistors used in this manner may be briefly stated as follows:

Jan 1, 1928

By H. J. Struth

The benefits of proration of oil production were perhaps more concretely realized in 1932 than at any time since the oil industry adopted nation-wide production control. Reduced output of crude petroleum, which brought the daily average of the United States down to approximately 2,000,000 bbl. from a peak in 1931 of more than 2,600,000, had a telling effect on the trend of oil prices. Mid-Continent crude was advanced in price from 776, for 36-gravity oil, to $1.04 a barrel. California crude, of 26-gravity at Signal Hill, moved forward from 736 to 976 a barrel. Pennsylvania crude, the only exception to the upward trend, rose in price from $1.82 per barrel to $2.02, only to react to $1.72. This was due to local conditions which necessitated an adjustment to overcome competition from other areas of the United States. East Texas continued to exert a far-reaching influence on the crude and gasoline market during 1932. Despite the fact that oil prices were advanced in most fields, large quantities of oil were produced in East Texas in violation of state proration orders, and sold in the market at prices considerably below official postings. This created competitive conditions in the gasoline market that were felt by all refining centers of the United States. The quantity of gasoline produced from cheap East Texas crude was not large, but the volume was sufficient to influence prices in practically all sections of the country. Thus, while the industry&apos;s&apos; economic situation showed visible improvement statistically, the unreported and unseen statistics originating in East Texas proved to be an insurmountable obstacle to the economic betterment that was otherwise apparently justified. Somewhat surprising to many was the fact that gasoline consumption was maintained within 10 per cent of the preceding year. Domestic consumption showed only a net decline under 1931 of about 8.5 per cent; exports dropped in volume to the extent of about 23 per cent. As a matter of fact, domestic gasoline consumption was only about 1.4 per cent less than it was in the predepression year of 1929. Exports, however,

Jan 1, 1933

By Benjamin C. Allen

The surface tensions of liquid chromium and manganese were determined by a modification of the dynamic drop-weight method and found to be, respectively, 1700 * 50 and 1100 * 50 dynes per cm at their melting points. Molten drops were formed LITTLE is known about the surface tension of liquid chromium and manganese, even though they are technologically important metals and widely used in steelmaking. In the past, direct determinations have been hampered by their high reactivity on the lower end of a vertically held rod inductively heated under argon. The technique essentially reproduced surface tensions reported for liquid nickel and zirconium using static drop-shape methods. and vapor pressure. In this work, surface tensions were measured by the drop-weight method, using induction heating under argon. EXPERIMENTAL WORK Chemical analyses of rods used are given in Table I. Chromium rods were prepared from iodide-process crystals which had been are-melted, hot-extruded, warm-swaged, and centerless-ground.&apos;

Jan 1, 1964

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By A. Singh, W. M. Fleming, J. J. Santana, A. E. Torma

The present study investigated the extraction of uranium from a low-grade ore by sulfuric acid and the removal of radium from the leach residues by brine solutions. The optimum leaching conditions were found to be 1.5 mole [£]-1 H2SO4, 6.Og[9]-1NaClO3, 75°C,50% pulp density and 750 rpm with respect to the rate of uranium extraction. The maximum theoretical attainable rate of uranium extraction was determined to be V = 1.09 x 10 -2 mole [¢]-1h-1 with respect to pulp density. The order of reaction was found to be zero regarding the effect of sodium chlorate concentrations. The apparent activation energy of uranium extraction was calculated from the Arrhenius plot to be [A]E a - 2.36 kcal mole-1 (9.87 kJ mole-1). Based on a statistical design, an empirical equation has been developed describing the rate of uranium extraction with the leaching parameters. This equation can be used to generate data which may be useful for scaling up the process to pilot plant level. The most efficient brine solution for the extraction of radium - 226 from the leach residue was found to contain one mole[f] -1 CaCl2 and 0.01 mole [2] -1 HC1. The two step leaching with this solution resulted 87% removal of radium from the leach residue. On the basis of this study, a flow-sheet has been proposed for the extraction of uranium and radionuclides from the ore and leach residue to yield almost innocuous tailings.

Jan 1, 1982

By George W. Riter

OUR mineral-land laws need revising so as to provide definite title at the outset to the mineral deposits within any definite piece of land. The laws as they now stand, especially those applicable to lodes, breed uncertainty as to rights of possession prior to patent; and to my mind this is the worst feature of all, worse even than the apex bugbear. It is now almost impossible for anybody to tell-with certainty what mineral rights exist within any area that is not covered by patent, or whether any valid rights exist at all. Our system is unique in permitting individuals to appropriate and exploit mineral lands of the public domain without notice of any kind to the Federal government, and to relinquish them without any ceremony at all. The result is a clouded record that cannot be cleared up until each claimant is put to some sort of final proof. In order to accomplish this, new Federal legislation will be required. The requirements for a mineral survey and the proceedings for patent have always been cumbersome and expensive; and perhaps out of regard for the poor claim owner, who can ill afford the outlay for that sort of thing, the law does not require him to go. through it unless he chooses to do so. Consequently, every active mining district has become encumbered with tangled groups of doubtful or conflicting locations, whose rights and boundaries, when any valuable ore is found, must usually be determined by lawsuits that are as expensive and as distressing as the stakes are high. So deeply has litigation entered into our mining system that a claim whose rights have never been disputed would probably be set down offhand, by $miner of the old school, as of no value. Think of the litigation over rights of possession on the Com-stock lode—12 leading companies involved &apos;in an aggregate of 245 suits within a period of less than eight years! Ambiguous local records; the chance of erroneously placed or obliterated monuments; doubt as to the sufficient performance of the statutory annual labor; uncertainty as to prior conflicting or overlapping locations; anxiety as to the changing attitude of the Department of the Interior and the Forest Service—such considerations as these make an unpatented mining claim an unclean thing in the eyes of possible investors. Is it any wonder that they keep themselvesand their money at a safe distance,

Jan 1, 1915

By W. I. Duvall, L. D. Sadwin

Three explosives with different detonation characteristics were tested by studying their cratering ability in a granite-gneiss. The strain wave generating characteristics of these explosives were also studied in the same rock medium. Correlations between the relative performance of three explosives as evaluated by crater studies and other methods of evaluation are indicated. Numerous test methods have been employed to evaluate the output performance of explosives; for example, the underwater explosion method, the airblast method and the ballistic pendulum method.&apos;*&apos; For blasting applications, the study of explosion produced craters and explosion generated strain waves are the most meaningful. This laboratory has employed these techniques extensively for many years and has shown that the detonation properties of explosives and their ability to generate strain waves in rock are related and that the amplitude and shape of the strain wave is related to some of the crater parameters such as slab thickness and fly rock velocity.3&apos;11 However, a good comparison between the relative performance of explosives as determined by the crater and strain wave methods had not been made. The purpose of this investigation was to determine if the relative performance of three explosives as determined by the crater method shows a correlation with the relative performance as determined by the strain wave method. If a good correlation exists between these two sets of relative performance, it should then be possible to relate the detonation properties of an explosive to its ability to break rock in a crater test. In most commercial blasting operations, the diameter of the blast hole remains constant even though the type of explosive may change. In general, it is the explosive volume rather than the weight which remains constant when two or more explosives of different density are compared. Therefore all tests in this investigation were conducted on a constant volume basis rather than on a constant weight basis. TEST SITE AND ROCK PROPERTIES The tests described in this paper were conducted at a granite quarry owned and operated by the Consolidated Quarries Div. of the Georgia Marble Co. at Lithonia, Ga. The tests were performed in an area where the exposed rock surface was nearly horizontal and where the general rock mass had few joints or faults. The rock has an apparent sp gr of 2.6 and a longitudinal propagation velocity of 18,000 fps. The characteristic impedance of Lithonia granite gneiss is 53(lb - sec/in3). EXPERIMENTAL PROCEDURE There are many parameters which must be considered in the study of explosion-produced craters. The role played by each variable in the explosive-rock-crater system can be determined by experimental techniques in which one parameter is varied while others are maintained constant. In this investigation, the crater geometry was studied as the depth was varied for each of three explosives. The explosive volume and rock-type were held constant for all crater tests. The experimental arrangement used in performing the crater tests is illustrated schematically in Fig. 1.

Jan 1, 1965