Search Documents

By A. J. Ardell, O. D. Sherby

The elevated-temperature steady-state creep behavior of polycrystalline a Zr was studied in vacuo under constant tensile stress. The experiments were conducted from 660° to 845°C over the stress range 870 to 5400 psi. The steady-state creep rate, is, of a Zr was found to be related to the applied stress, a, and temperature, T, by the equation where C is a constant. Two interpretations of the data are considered, each requiring different values of the parameters ß, Q, and . It is shown that this formula can be derived using Gilman's phenomeno logical equation relating dislocation velocity to the shear stress for the case where dislocation mobility is limited by the nucleation of kink motion. From the fundamental dependence of strain rate on dislocation velocity and the density of mobile dislocations, the factor exp(ßo) can be related to the stress dependence of the dislocation density, and Q to the energy of kink formation. The two interpretations considered are as follows: Case I—the parameters are adjusted so that the equation above describes the data over the entire range of stress and temperature, implying that creep is controlled exclusively by dislocation glide; Case IIthe parameters are adjusted to allow for the possibility that creep is diffusion-controlled at high stresses but glide-controlled at low stresses. For both cases the values of the parameters are within the spread permitted by the data. Factors favorable to the observation of the unusual stress -dependence of i, for a Zr are discussed and it is shown that the anomalously rapid rates of self-diffusion and the low modulus on the principal glide system are primarily responsible for the anomalous creep behavior. Metal-lograflhic observations are presented and discussed with reference to the overall creep behavior. PREVIOUS investigations of the creep behavior of a Zr have been conducted from room temperature to about 500C The results of these investigations are primarily of engineering significance because of the variety of conditions under which they were carried out, and the low testing temperatures employed. Little information is available concerning the fundamental nature of the elevated-temperature creep behavior of a Zr. This investigation of the creep behavior of a Zr above half the melting temperature (the melting temperature, T,, of a Zr is estimated to be about 1860"K was initiated because there are two significant anomalies of the physical properties of a Zr: a) the rate of self-diffusion in polycrystalline a Zr is anomalously rapid: b) both Young's modulus for polycrystalline a Zr and the shear modylus as-sociated with the prismatic slip system { 1010)( 1120) (the principal slip system in a Zr 7) have anomalously large temperature variations The importance of these quantities to the understanding of creep behavior has been demonstrated, and it was hoped that this investigation would provide a critical test of the predictions based upon the analysis of creep data for other pure metals. However, as the investigation progressed it became increasingly clear that the unusual creep behavior of a Zr could not be analyzed in a conventional manner. 1) EXPERIMENTAL EQUIPMENT AND PROCEDURES Two grades of zirconium, designated A and B, were used in this investigation. The analyses, as supplied by the vendors, are presented in Table I. Material A, with a nominal purity of 99.84 pct, was supplied by the Wah Chang Corp. in the form of cold-rolled sheet from which specimens were machined without further fabrication. Material B, with a nominal purity of 99.95 pct, was purchased from the Nuclear Materials and Equipment Corp. in the form of iodide crystal bar.

Jan 1, 1968

By Wiley C. Buford

Gary Works No. 1 BOP Shop is a three furnace shop which went into operation December, 1965. The heat size is over 200 tons, with a substantial percentage of the production used to feed a Continuous Slab Caster. Vessels are driven by a shaft mounted bull gear and main housing utilizing eight 35 HP flange mounted motors and primary gear reducers. Torque absorption is controlled by two spring actuated torque arms. At 1:00 p.m. on Thursday, August 6, 1970, as "E" furnace was being turned down for a preliminary test, the drive side trunnion bearing failed. The furnace dropped slightly and shifted several inches north in the direction of the drive unit. The decision was made to tap the heat which was done without incident and the vessel uprighted. No attempt was made to completely drain the slag from the vessel, so as to avoid any further damage to the trunnion shaft bearing surface. The bearing failure occurred approximately four years and eight months after start up of the shop. Unfortunately ?M? furnace had gone down for a normal reline two days prior to the bearing failure, leaving the shop with only one operating furnace.

Jan 1, 1972

By Benjamin L. Miller

THE essential differences expressed by the different speakers participating in this symposium concern merely the relative emphasis placed on the subjects that are commonly included under the term "geophysics" and the branches of science that form the basis for investigations in this field. In order to appreciate the present situation it may be profitable to briefly refer to a few historical matters. One can find almost countless descriptions of geological phenomena long antedating the introduction of the title of "geology," which has been credited to Richard de Bury in the fourteenth century. Interpretations, when they were offered, were generally pure speculation. Only toward the close of the eighteenth century do we find theories developed as the result of observations and tested by additional observations. It is difficult to select and give proper credit to the individual who was particularly responsible for turning geology into a distinctly observational science. William Smith, who has been called the "Father of English Geology," certainly represents the period when observation was the only method used. As he traveled through the British Isles, "sometimes 10,000 miles in a year," he was continually making notes of his observations. Geikie says: "His plain, solid, matter of fact intellect never branched into theory or speculation, but occupied itself wholly in the observation of facts." William Smith, with others of his time, definitely laid firmly the foundations on which modern geology has been built. Field and laboratory observations can no longer be said to constitute the sole basis for geologic contributions but we have not laid aside the methods of Smith and his followers. It is folly to underestimate the fundamental value of the observational part of geology in the present. The objection to purely observational geology is that it is mainly qualitative and not quantitative, general and not specific. No one can deny this charge and probably there are few who do not welcome every method or process whereby we can put aside generalities for definite established values. Physics is the science that has particularly come to the aid of the geologist in this respect. CONTRIBUTIONS OF PHYSICS It is not the intent of the writer to enumerate or to evaluate all of the contributions to geologic advance in the field of physics. A few only are used for the purpose of illustration. When Clarence King, Director of the United States Geological Exploration of the Fortieth Parallel, invited Ferdinand Zirkel to study 2500 thin sections of rocks collected from the western United States, the use of the microscope came into general use. Zirkel's report was published in 1876. He was not the first to use transmitted light for microscopic rock determination, some work having been done by Henry Clifton Sorby and others some years earlier, but he was the first to put into general use this method. We may well claim that this

Jan 1, 1941

By A. B. Kinzel

Precise knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly .ell known. General Method The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By A. B. Kinzel

Precise knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly .ell known. General Method The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By Walter L. Maxson, Fred C. Bond

THIS paper is a continuation of two earlier papers, l, 2 and presents new data on the grindability of various ores and other materials-the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRINDABILITY OF VARIOUS ORES This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at x6-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1 ½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1938

By C. S. Barrett, O. R. Trautz

Previous investigations have shown that lithium is body-centered cubic from near its melting point to the temperature of liquid air.1,2,3 Nevertheless there was an incentive to search again for a transformation at low temperatures: C. Zener4.5 has remarked that the low value of the elastic modulus (C11 — Cl2)/z of body-centered cubic metals and alloys implies a rapid increase in free energy with decreasing temperature, which would favor the occurrence of a transformation; also the shear movement to which this modulus applies is one that can transform a body-centered cubic structure into a slightly distorted face-centered cubic structure. It was confirmed that lithium does not transform spontaneously at liquid nitrogen temperature, but it was found that a transformation can be induced at this temperature by cold working the metal,6 and at slightly lower temperatures a different transformation occurs spontaneously. Transformations were also found in solid solutions of magnesium in lithium. The Nature of the Transformations Before presenting a detailed treatment of the technique used and the specific data obtained, it would be well to give a brief survey of the general characteristics of the transformations. A new crystal structure begins to form spontaneously in a specimen when it is cooled below a critical temperature. In lithium the structure appears to be close-packed hexagonal; in theLi-Mg alloys most of the diffraction lines (but not all) are near those for hexagonal lithium. The transformation proceeds as the temperature is lowered and soon stops if the temperature is held constant or raised. The course of the transformation on cooling is indicated by the curve at the lower left of Fig -I. This curve is drawn in stepped fashion because the transformation goes by discrete steps with audible clicks. Because of the similarity to the decomposition of austenite into martensite in steels, it seems appropriate to designate the beginning of the spontaneous transformation on cooling as the Ms point. On heating to room temperature after the low temperature treatment only the usual BCC structure is found. On heating, the low temperature modification begins to disappear at a temperature which will be designated as Ac. The transformation on heating is halted when the rise in temperature is halted. The temperature must be raised 40 to 50°C above Ac before the reversion is complete—an interval which is sensitive to the rate of heating and to the time of holding at temperatures above Ac. This behavior on heating thus has similarities also to the formation of martensite in the cooling of steels.

Jan 1, 1949

By Quentin Singewald

SOME of the broader relations between structure and ore deposition along the London fault, deduced from a thorough study of the geology of the eastern part of the Mosquito Range, should be of general interest to economic geologists. The first part of this paper is a generalized state-ment of the geology of the region in which the London fault is located; it may be supplemented by reference to several earlier publications by the writers and to the U. S. Geological Survey's Professional Paper 148, on the Leadville district. The second part deals with the structure of both the fault and the disturbed zone adjoining the fault. The third part dis-cusses the salient features of the ore deposits, particularly emphasizing structural control. The two generalized maps are complementary to one another but contain too many data to show on a single small map. The London fault is between Leadville and Alma, and the ore deposits along it are said to lie in the Alma district. Field work in this district, during six summers since 1927, has been a part of the cooperative work of the U. S. Geological Survey, the State of Colorado, and the Colorado Metal Mining Board. The writers have made use of work by R. D. Butler, J. W. Vanderwilt and R. E. Landon. G. F. Loughlin and C. H. Behre, Jr., who have worked on the west side of the range, have con-tributed valuable suggestions. Mining men of the district have aided in many ways.

Jan 1, 1936

By Hans Lundberg

By electrical prospecting, orebodies that do not otherwise manifest themselves at the surface may be located. Conditions favorable to success with the methods are: Favorable geological conditions, such a proportion of minerals of good electrical conductivity in the orebody as will render the latter materially a better conductor than the enclosing rock, situation of the orebody within the range of influence of the electrical currents used and in proportion to this range a sufficient area of horizontal cross section of the orebody. The result is to permit of spotting drill holes accurately and to save the expense of drilling barren ground. THE art of prospecting, like other branches of mining, has developed rapidly during the last ten years, mainly because of the advancement of mining geology, but also because of the development of "geophysical methods," which are based on the different physical characters of minerals and rocks, e. g., specific gravity, elasticity, and magnetic and electric properties. These methods have proved of great value, especially in countries where the rock is covered by soil and direct geologic investigation is out of the question. In prospecting for orebodies, the methods based on studying differences in electrical conductivity have proved most successful; for which reason, the methods of electrical prospecting have been subject to the most energetic and systematic work, especially in Sweden. This paper gives a brief description of the methods of electrical prospecting now in use, especially the new electromagnetic methods, which have not been described before. The great differences in the electrical properties, especially in conductivity, between ore minerals and rock minerals are fundamental to all methods of electrical prospecting, for which reason, the electrical conductivity of ore minerals and rock minerals has been carefully studied in connection with and previous to the development of the various methods of prospecting with electricity. Ore minerals with a metallic luster, such as chalcopyrite, iron pyrite, galena, specular iron, magnetite, etc., also graphite and a number of cows, have considerably higher conductivity than the surrounding rock and soil (see Table 1). The figures of the table denote the specific resistance W, expressed in ohms for a cube with an edge of 1 centimeter.

Jan 7, 1925

By F. N. Rhines, A. H. Grobe

At elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing. When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible1 and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver. Norbury2 and Leroux and Raub3 have reported internal oxidation (subscaleiormation) in alloys of silver with 2, 7.5, and 30 per cent of copper. The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver.4 Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation. Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detai1.5,6 The present research confirms this anticipation. The oxidation of a series of 20 dilute alloys of silver has been studied metallographically; some types of subscale not encountered among the copper alloys have been found. Instances of internal oxidation in alloys of most of the metals of the 1-6 and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking. A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation; i.e., they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them. In a study of 40 alloys of these white metals only a few cases of internal oxidation have been found. The probable reasons for this difference in behavior will be discussed presently. Experimental Procedure Silver.—The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99.993 per cent Ag)* and the purest avail-

Jan 1, 1942

By A. H. Grobe, F. N. Rhines

At elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing. When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible1 and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver. Norbury2 and Leroux and Raub3 have reported internal oxidation (subscaleiormation) in alloys of silver with 2, 7.5, and 30 per cent of copper. The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver.4 Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation. Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detai1.5,6 The present research confirms this anticipation. The oxidation of a series of 20 dilute alloys of silver has been studied metallographically; some types of subscale not encountered among the copper alloys have been found. Instances of internal oxidation in alloys of most of the metals of the 1-6 and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking. A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation; i.e., they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them. In a study of 40 alloys of these white metals only a few cases of internal oxidation have been found. The probable reasons for this difference in behavior will be discussed presently. Experimental Procedure Silver.—The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99.993 per cent Ag)* and the purest avail-

Jan 1, 1942

By K. N. Weaver

In the early 1950's the cement industry began putting a new emphasis on geology. This article points up some of the industry's raw materials problems that geologists are uniquely qualified to handle. Portland cement can be made from relatively abundant industrial minerals and rocks, and this may explain why cement producers placed little emphasis on geology during the early days of the industry. After World War 11, however, the industry began to recognize the need for geological exploration and some of the larger companies began to build a permanent geological staff. This development has its roots in: 1) The rapid expansion of the industry. After World War II and continuing into the early 1950's the demand for cement far exceeded the production capacity. This placed a great deal of pressure on the producers to enlarge capacity at their plants and to develop new sites. 2) The closing of many cement plants due to inadequate raw materials. Producers feared lack of raw materials due to inadequate exploration and evaluation. 3) An ever increasing pressure for upgrading of the quality of portland cement, necessitated upgrading the quality of raw materials. 4) The increasingly large capital investment needed to build new cement plants required a higher degree of accuracy in reserve calculation. These reasons are more or less self explanatory and will not be elaborated on. They are outlined to illustrate the probable evolution of thought among cement management to justify the development of a geological staff. In the author's personal experience the geologist must continually readjust to changing conditions within the industry. For example, cement production capacity grew so rapidly that today production is only about 70% to 75% of rated capacity (73.8% in 1963). Therefore, whereas the geologist's function during the active expansion of capacity was primarily one of exploration, one of his major functions today is the development of existing reserves. This assumes of course that reserves at existing plants have been proven to be adequate in terms of the company's reserve policy. Through the proper development of raw materials, the geologist can markedly influence quality control, production and long range planning. Examples of several of the operations of Medusa Portland Cement Co. will illustrate how proper attention to geologic detail pays off in the above areas. Because limestone is the major raw material of port-land cement, the examples will be concerned with it. DEVELOPMENT OF GEOLOGIC DETAIL One of the prime objectives of an exploration or development project should be the establishment of the stratigraphy and structure of the deposit. The basic tool for exploration and development is still the core drill, and the geologist must gain a maximum amount of information from a minimum amount of drilling. In order to obtain this objective the following is essential: 1) Adequate detailed geologic logging of cores. The core is first logged and separated into lithologically distinct units. In order to make the lithologic breaks as meaningful as possible, representative pieces of core (not all) are etched in dilute HCI. This removes the "drill polish", brings out the structure of the rock and indicates the proportion of dolomite and argillaceous material because dolomite and argillaceous material etch in relief. In this way the lithologic breaks become clearer and one gains a general idea of the chemical makeup before analysis. This method of logging lessens the probability of including two types of stone, e.g. limestone and dolomite into the same sample for chemical analysis. 2) Representative sampling for chemical analysis. After logging, the lithologic units are sampled for chemical analysis. A representative analysis can be obtained by extracting a 1-in. sample for every foot of core. For example, a lithologic interval of 10 ft to 20 ft would yield ten 1-in. samples taken at 11 ft, 12 ft, 13 ft... and 20 ft. These samples are then crushed, pulverized and split into a sample for chemical analysis. This sampling method represents a significant saving of time over splitting the entire core. 3) Preparing the core as a record. Because of the expense of storage and the difficulty of handling large amounts of core, only representative samples of each lithologic unit are saved for reference. An

Jan 1, 1965

By F. E. Buch

THE Smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The Smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter ,aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pct moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pct oxide copper. The predominating minerals are chalcocite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating k bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. GENERAL DESCRIPTION Flotation concentrate, containing to pct moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1947

ALABAMA Anniston.-Bretz, J. A. Carrington, F. G. Gerber, A. B. Klugh, B. G. Semple, R. A. Ashland.-Barton, .J. Bessemer.-Abbott, C. E'. Ball, T. L. Beaver, J. J. Ferguson, V. Salmon, H. S. Sehaber, C. F. Whatley, W. J.

Jan 1, 1923

By Myron K. Rodgers

In rock- or ore-crushing tests all data, in order to be valuable for study and comparison, should be obtained and tabulated under conditions as uniform as possible. The results of many such tests have no value for comparison, because of incomplete data and the lack of uniform conditiops, screens and scale of sizing, etc. The purpose of this paper is to suggest a form of standard specifications which may be developed by the Milling Committee and approved by the A. I. M. E. for rock-crushing tests. It is not intended to discuss any theories of rock crushing. Reports of rock-crushing tests should include the following details: 1. Description of the machine employed (jaw or gyratory crushers, rolls, stamps,tube mills, Chilean mills, etc.), 2. Method and material (timber, concrete, etc.) of foundation. Much power is dissipated in the vibration of poor foundations. 3. Locality from which the rock or ore was obtaincd, and geological, mineralogical, and physical characters of the material. 4. The power consumption of the machine running with no load and with full load, the unit of power being 1 hp. per 24 hr, 5. The capacity of the machine in tons (of 2000 Ib.) per 24 hr. 6. The duty in tons per horsepower-day. 7. The screen analysis of feed and product by the proposed A. I. M. E. standard screen scale. On the foregoing statement, the following remarlrs are offered. Toughness of Rock Table P shows the relative crushing duty of the same machine on three different characters of rock, all other crushing conditions being the same. This table indicates that the specific resistance of the rock to crushing, may affect the crushing duty of a unit of power as much as 300 per cent. Perhaps this quality may be called toughness. It is not a function of hardness only. For comparison of tests, rocks should be divided into

Jan 1, 1916

By R. J. Piros, Brusenback, D. A. Dahlstrom

DEWATERING fine coal has been a serious problem to many operators who desired to wet-wash finer sizes and maintain high recovery. Centrifugal driers have become popular for this purpose for sizes between 3/8 in. and 14 mesh. Below 14 mesh the perforated screen centrifuges lose a large per- cent in the effluent solid bowl types that do retain -14 mesh coal, produce excessive degradation, tend to retain the highest ash fraction in any size fraction, and are subject to abrasion, which results in higher maintenance. In 1949 Truax-Traer Coal Co. planned a cyclone installation at their Ceredo preparation plant to recover coal down to 150 mesh with approximately a 14-mesh top size. Since available centrifugal equipment was not considered satisfactory, an investigation of rotary vacuum filters was begun in cooperation with the Peterson Filters and Engineering Co. to determine the suitability of the Peterson Top Feed Reservoir (TFR) filter. This investigation, which is described below, has resulted in a highly satisfactory installation of two 6x10-in. Peterson TFR filters that have been in operation over a year. After some preliminary laboratory batch vacuum filter tests, a pilot plant double-drum Peterson TFR filter was installed at Ceredo to prove the feasibility of vacuum filtration and determine optimum conditions. The full scale units were then installed on the basis of the pilot plant results. This was followed by an extensive research program on vacuum filtration in the laboratory at Northwestern University to investigate basic design and operating variables and their influence on final moisture con- tent of the filter cake. A method of scale-up from laboratory batch tests to the full-size unit was also proposed and proved. Because of the importance of dewatering fine coal today, it was felt that the results of the three steps should be made available for the use of others facing this problem. The work at Northwestern is given in a theoretical section following the discussion of the pilot plant and full- scale operation. Fig. 1 is a flow diagram of the cyclone and filter installation. The feed is drawn from below the

Jan 1, 1952

By A. H. Grobe, F. N. Rhines

AT elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible' and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver Norbury2 and Leroux and Raub3 have reported internal oxidation (subscale formation) in alloys of silver with 2, 7 5, and 30 per cent of copper The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver' Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detail 5,6 The present research confirms this anticipation The oxidation of a series of 20 dilute alloys of silver has been studied metallographically, some types of subscale not encountered among the copper alloys have been found Instances of internal oxidation in alloys of most of the metals of the I-b and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation, i e , they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them In a study of 4o alloys of these white metals only a few cases of internal oxidation have been found The probable reasons for this difference in behavior will be discussed presently EXPERIMENTAL PROCEDURE Silver -The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99 993 per cent Ag)* and the purest avail-

Jan 1, 1942

Teamwork: The famous first sentence of an essay en- titled Aphorisms, by Hippocrates, is as follows: "Life is short, the Art long, opportunity fleeting, experience treacherous, judgment difficult." The future of science does not depend so much on the number of scientists or the number of colleges, but rather on the individual qualities and the degree of perfection of a limited group of leading scientists and colleges. These are individual factors which require inherent talent which in turn is a condition evolved after generations of culture. Thus, very elaborate higher education for indiscriminate masses of humanity or students may not necessarily show the expected results. In other words, it is possible that higher specialized education should be given only to the few talented individuals, and their capacity and worth should be judged by as highly qualified and talented teachers. Quality is the greatest of all competitive aids. An essential qualification that must be possessed by a quality mineral industries college is a high caliber teaching staff, for the mineral sciences will advance in the coming years only if the leading minds of today are made avail- able as the mental springboards for our scientists of tomorrow. Mineral industries schools are finding it increasingly difficult to maintain a high caliber staff of instructors and administrators in competition with private business and governmental demands for similar

Jan 1, 1950

By H. A. Guess

Introduction. History and Production Statements. Southeast Missouri is the oldest of the large producing districts of the United States. The first recorded production from disseminated ores was in 1869, although for many years prior to that time lead had been milled from shallow pockets, and steady growth in production has been shown ever since, the greatest increases being during the past five years. The production by years for each of the operating companies from 1869 to 1907, inclusive, is given in Table I. In Table 11. is given the production by years from 1908 to 1912, inclusive, for the district as a whole, showing the tonnage of crude ore mined, yield in concentrates, average assay of concentrates; yield in metallic lead both per ton of crude ore and in total; also approximate value of the yearly production. It is interesting to note that the production for the 5-yr. period 1908 to 1912, inclusive, is practically equal to the total previous production, viz., the 39-yr. period 1869 to 1907, the summary being as follows:

Jan 1, 1915

By J. S. Mitchell

Cobalt recovery from arsenical concentrates by pressure leaching and reduction involves special methods and operating problems. Principal steps in the process are auto-oxidation acid leaching under pressure, filtration of the tailings, purification of the solution, hydrogen reduction of the ammoniacal solution, and electrical furnacing for sulfur removal and granulating the metal. Extracting cobalt metal from arsenical ores has presented a major metallurgical problem for many years. In acquiring the Blackbird mine near Salmon City, Idaho in 1943 Calera Mining Co. accepted the challenge to solve this problem.

Nov 1, 1956