Search Documents

By M. S. Burton, G. V. Smith, A. Rosen

The kinetics of re crystallization and the effect of recovery on recrystallization of pure iron were investigated within the temperature range of 517" to 632 OC. Grain growth and activation energies were also studied. Two stages can be distinguished during recrystallization; the first is gvowth-controlled and the second is nucleation-controlled. The extent to which the first stage succeeds before the second stage begins depends on both temperature of recrystallization and temperature of recovery. The softening of cold-worked metals and alloys due to transformation of the deformed crystals to strain-free equiaxed grains during annealing is well-known, and early inestiators established that recrystallization kinetics is strongly influenced by minute quantities of impurities. Generally, it is believed that impurities decrease the rate of recrystallization and the rate of grain growth. To understand the basic phenomena of recrystallization, investigations should be on pure materials. Most of the research on high-purity materials has been on metals having the fee Bcc materials, and especially high-purity iron, have been studied only in recent years. It is known that recovery may influence recrystalliation;" however, no general description of the influence, applicable to all materials, has been presented. This paper presents results of a study of the recrystallization kinetics of high-purity iron, after 60 pct cold deformation by drawing, with particular reference to the influence of recovery on the rates of recrystallization and grain growth. From observations of these rates, conclusions are drawn concerning nucleation. MATERIAL AND EXPERIMENTAL PROCEDURE Preparation of Material. High-purity iron, prepared by zone refining of vacuum-melted electroiytic iron at Battelle Memorial Institute under sponsorship of the American Iron and Steel Institute, was used in this study. Table I gives the reported chemical analysis of the material, taken at a point near the last molten zone and thereby rep- resenting the maximum impurity level for the entire bar. Prismatic specimens, approximately 10 x 10 X 50 mm, were sawed from the 50-mm-diam bar, perpendicular to the zone-refining direction, and turned to cylindrical shape. These specimens were sealed in quartz capsules under vacuum, approximately 10"e mm Hg, austenitized at 930° C for 15 min, slowly cooled, removed from the capsules, and cold-worked in air by swaging to approximately 20-pct reduction of area. The encapsulating, austenitizing, and swaging operations were repeated two additional times, after which the samples were encapsulated, austenitized, and cold-drawn to 60-pct reduction of area. A further vacuum anneal at 630°C for 120 min and cold drawing to 60-pct reduction of area produced wire 2.8 mm in diameter. The drawn wire was electropolished to remove deformed material on the surface, after which it was sawed into 4-mm-long specimens for the recrystallization study. Microscopical examination before the final cold reduction revealed equiaxed grain structure with very fine grains in a thin layer near the surfaces of the specimen and nearly uniform ASTM 3-4 grain size in the center. Recrystallization Heat Treatment. a) Direct Recrystallization of Cold-Worked The 60 pct cold drawn iron specimens were recrystallized at five temperatures, 517, 556, 590°, 612, and 632C, in a lead bath covered with graphite (the temperature was controlled to 1°C). Specimens were treated for twelve different times at each temperature, and all were water-quenched after heat &eatment. b) Recrystallization Following Preliminary Recovery Heat Treatment. After cold working, specimens were sealed into quartz capsules under vacuum, 105 mm Hg, and recovery-annealed at 362", 400", and 440°C for 20 hr prior to recrystallization. No evidence of recrystallization was found

Jan 1, 1964

By A. J. Bartlett

ISLAND Creek conditions are generally referred to as ideal; yet, as at all other properties, there are all known hazards of coal mining. The hardest of these hazards to combat is the human element. The basic thought in the minds of the management of these properties is to produce coal with the utmost safety, and it has impressed upon its supervisory force that it does not want a ton of coal unless it can be produced safely. This company has instituted a mine inspection department, which reports direct to the general manager, and all matters pertaining to safety come under the direction of this department. Through the medium of the inspection department, the management is kept in touch with the actual conditions existing in general at all mines. Inspections are made regularly and continuously; that is, at all times while the mines are in operation some sections of some mines are being examined. These inspections cover all active and inactive workings. Miners are con-tacted in their working places and other employees at their respective work. A thorough check is made to see that the state mining laws are complied with and that company safety rules are being observed. Night shifts receive the same attention as day shifts. All violations and dangerous practices are brought to the attention of the plant supervisory force with suggestions and recommendations; major hazards of emer-gency nature are taken up immediately with the management. Peri-odical inspections are also made of all tipples, preparation plants, dumping and hoisting equipment, to see that all machinery is properly guarded, and walkways and platforms properly fenced; conditions of equipment and mechanical defects are also reported. Reports of inspection are written in letter form and in such a manner as to give the management a picture-of the existing conditions at the time of inspection. Copies of inspection reports are forwarded; to the superintendents with the general manager's comments.

Jan 1, 1937

By V. V. Strishkov, Zane E. Murphy, George Markon

Soviet industrial expansion depends on coal as a source of power and raw materials for the USSR's metallurgical and chemical industries. Knowledge of the Soviet Union's coal resources and production outlook is essential for a critical evaluation of the Soviet industrial potential. Although there is considerable literature on the Soviet coal industry, no single source provides an authoritative study of how the coal industry functions and how well it per- formed its job. Soviet reports are singularly lacking in the precise data in terms that are comprehensible to a westerner. It is essential, therefore, to clarify the terms in Soviet parlance. These terms are not comparable to those in common use in the West and are the cause of most inaccurate results. Official Soviet data on labor productivity refer to a limited group of "production workers" while in the West all wage earners are counted. Statistics are based on unprepared or run-of-mine coal, whereas it is customary elsewhere to measure productivity in terms of marketable coal. Thus, many western publications, while diligently and accurately reporting published Soviet data, overstate the case, presenting an exaggerated picture of Soviet progress in coal production and technology. (In terms of Western criteria, there is a three-fold exaggeration of labor productivity.)

Jan 5, 1973

By T. S. Jr. Sligh

OF all the qualities that are essential in a good cigar tobacco none is quite so important as the burn. This term is general and includes many points, the most important of which are evenness of burn, color of ash, firmness and coherence of ash, and fire-holding capacity. The fire-holding capacity refers to the length of time the leaf or cigar will continue to, glow after ignition. Chlorides tend to prevent complete combustion and products are formed thereby that are injurious to the flavor and aroma. On the other hand, the carbonates of the alkalies, particularly of potassium, aid the combustion and increase the fire-holding capacity. Barth1 thought that the harmful effect of the chlorides was due to their fusing and coating the tobacco, thereby preventing complete combustion. Schlosing,2 Nessler,3 and Garner,4 suggested widely different theories to account for the favorable action of potassium salts. In order to study carefully the action of the various salts upon the course of combustion of the cigar a knowledge of the temperature of the burning cigar is necessary. Lehmann5 who seems to be the only investigator who has made any attempt to determine the temperature of a burning cigar gives 480° C. as the maximum temperature which he recorded. It is evident, however, that his measurements were in error, probably on account of the method and apparatus used, since the lowest visible red corresponds to a temperature of about 575° C.

Jan 9, 1919

By Dermot M. Ross-Brown

Introduction Slope angles are one of the major factors affecting the shape of the final pit and the location of the walls Due to differences in geology, the optimum slope angles vary from pit to pit and within different parts of the same pit. Indeed, it is not unusual to have different slope angles for the top and bottom portions of the same cross section. The optimization of these slope angles is a major study in itself and this chapter is intended as a general introduction to the subject. It is not intended to be a comprehensive text for the absolute beginner The objective is to put the various aspects of slope stability analysis into relative perspective by describing the vari¬ous analytical techniques available and indicating when each may be most appropriately used References are made to the many excellent texts and papers on slope stability for the reader who does not have a formal training in soil or rock mechanics. In writing this chapter, an assumption has been made that a tentative mining plan has been drawn up, includ¬ing a preliminary estimate of the slope angles. It has also been assumed that all the necessary field and laboratory data has been collected and reduced to a form suitable for input into the stability analyses.

Jan 1, 1979

By Wilbur H. Grant

THE property of the United Comstock Mines Co. lies in the eastern foot-hills of the Sierra Nevada Mountains, in the Washoe mining district of Storey County, Nev. Commencing at the boundary line between Virginia City and Gold Hill, covering all the town of Gold Hill, it extends south to American Flat; the main camp, or the new town of Comstock, the mills, shops, residences of employees, and the main haulage-tunnel portal are located on American Flat. The property extends for about 10,300 ft. along the lode; this covers the southern end of the main Comstock lode, the Knickerbocker branch, and the junction of the Silver City branch with the Comstock lode. Within the property, 5000 ft. of the main Comstock lode is known to have been productive, 1000 ft. of the lode at the northern end of the property is thoroughly developed, and 1000 ft. south of this is partly developed; this leaves about 3000 ft. of the known productive portion that has not been opened up by this company. The northern end of the property, or the Imperial mine, has been intricately developed by five main levels and numerous sublevels. The Yellow Jacket ground to the south has been partly developed by the reopening of three old levels. In addition, the main haulage level is driven from the portal at Comstock for 9250 ft., to the north end of the property; about 5500 ft. of this `is in the foot wall of the lode and parallel to it.

Jan 11, 1922

By J. R. Low, M. Gensamer

During the course of an investigation into the drawability of automobile-body sheet steel, it became apparent that certain advantages would be possessed by a deep-drawing steel with a very low yield strength, but almost normal tensile strength, provided a reduction in yield strength could be accomplished without sacrifice of ductility and fine grain size. It would also be desirable to have this steel free from strainaging; that is, free from the tendency for the yield point to return after it had been eliminated by straining. It was known that wet hydrogen treatment acted to eliminate aging, but as carried out by other investigators, at relatively high temperatures, this treatment resulted in grain coarsening. It has been established by some of the experiments reported in this paper that all of these objectives can be accomplished by treatment in wet hydrogen at a low temperature, in the neighborhood of 720°C. The time of treatment is relatively short (about 3 hr. to completion with 20-gauge sheet) if the water content of the hydrogen atmosphere is made fairly high, say almost 30 per cent by volume. At this temperature, the grain size remains fine in the time required. After this treatment sheet reduced the usual amount by cold-rolling has a grain size of about A.S.T.M. No. 7. The yield point is completely eliminated, and the yield strength is reduced to a very low value, in the neighborhood of 15,000 lb. per sq. in. The stress-strain curve departs gradually from the straight-line elastic part after the fashion of nonferrous deep-drawing alloys. This elimination of the yield point is accompanied by a very low indentation hardness; for example, 32 Rockwell B or even lower. There is no aging as measured by increase in the yield strength upon aging at room temperature or for 3 hr. at 200°C., after stretching about 10 per cent in tension. Tensile strength is only slightly less than the box-annealed sheet, seldom dropping much below 40,000 lb. per sq. in. Elongation is practically unchanged, or increased slightly. The term yield point, as here used, refers to the phenomenon of heterogeneous deformation occurring at a substantially constant load, observed principally in annealed low-carbon steels. If such a steel is loaded in tension, the load increases steadily with elastic strain, suddenly falls, fluctuates slightly about some constant value for a time and then begins to rise again as deformation proceeds. The maximum initial load before the sudden drop is generally called the "upper yield point"; the value of the load where deformation proceeds at a

Jan 1, 1943

I SHALL proceed in this chapter to tell you about lead. Because this metal is overabundant in wateriness, and also because it has its other substances in poor elemental mixture, it is highly impure. It is called an imperfect, leprous, and little-fixed metal, which it clearly shows itself to be because of the ease of liquefying it and because it is easily converted largely into a dross that is almost earthy and also because of the stain that it leaves when it rubs against anything. Nevertheless, when we consider its effects, we judge it to be a metal that we are greatly indebted to. Even though Nature in creating us has put into our souls such a thirst and desire

Jan 1, 1942

By H. G. Moulton

THE INCREASING scale of mining operations over the past decade, particularly in connection with the exploitation of large bodies of comparatively low-grade copper ores, has made necessary the study of the behavior of rock under failure. When extractions of as high as 40,000 tons a day are reached in steam-shovel operations and as high as 20,000 tons per day in underground mining operations, it is evident that excavations soon become of such size that the behavior of the rock will often be dependent on fundamental principles applicable to more or less homogeneous materials under stress, rather than on weathering or local planes of weakness. In the ordinary rock excavations encountered in civil-engineering practice, such as excavations for subways, highways, railroads, etc., rock faces are not carried to depths sufficient to develop any pressures, or consequently any failures, except those due to loose masses resulting from local planes of weakness. When, however, orebodies whose tonnage is measured by hundreds of thousands are to be extracted by steam-shovel operations in open pits, it is necessary to determine if possible in advance the slopes that the sides of the pits will assume, for these slopes influence the shape of the excavations and thereby the amount of ore that may be extracted by the open-pit method. When large orebodies are mined underground at depths of 300 to 500 ft. (91 to 152 m.) by caving methods, the surface subsiding as the ore is withdrawn, it is necessary to determine in advance the outermost limits of fracture in the subsiding surface, for on the delineation of these limits depends the location of surface improvements, mills, smelters, etc. and also the location of development work, such as hoisting shafts, main haulage levels, and all other underground openings that must remain undisturbed during the period of ore extraction. Heretofore, in civil-engineering practice, it has been assumed that earth and rock behave differently in failure. For the calculation of earth

Jan 2, 1920

By George Sears

UNTIL a comparatively few years ago, interest in tantalum was limited almost wholly to its scientific investigation, but its extreme resistance to the action of even the strong mineral acids, its great avidity for the common gases, hydrogen, oxygen and nitrogen, and its capacity for transforming alternating to direct current are winning for it a place in our industrial life. Tantalum is not attacked by any single acid except hydrofluoric, nor is it affected by solutions of alkalies. Aqua regia, which readily dissolves both platinum and gold, has no action on it. This resistance to the common corrosive agents is an outstanding property of tantalum and accounts for many of the applications to which it has been put. When heated, tantalum reacts readily with oxygen and nitrogen and absorbs large volumes of hydrogen, 740 volumes being taken up at a dull red heat. This capacity for absorbing gases is being utilized to an increasing extent in the manufacture of vacuum tubes, in which tantalum is used for the metal parts, especially for grid wire. It is said to be a superior metal for this purpose, particularly in power and sending tubes, because of its low secondary emission. The use of tantalum in the manufacture of electrodes, dishes, spatulas and other laboratory apparatus appears to be fairly steady. There has been some development in its use for dental instruments, surgical tools, pen points, hypodermic needles and acidproof pumps. Recently it has been used in the manufacture of spinnerets for the rayon industry, of nozzles for the manufacture of artificial casings for sausages and of lining for plant equipment.

Jan 1, 1930

By C. L. Dake

RESIDUAL deposits occur both as products of weathering and as products of hydrothermal decay. PRODUCTS OF WEATHERING That climatic conditions affect greatly both the rate and the results of weathering, is shown. in temperate, polar, arid, and tropical regions, each of which will be considered separately. Weathering under Temperate Climates The decomposition of any rock is accomplished by the removal of the more soluble bases, and a concentration of the relatively insoluble oxides of iron, aluminum, and silicon. By reason of its some-what greater solubility, silica is much more subject to removal than iron and alumina. The two important residual end products of weathering are sands and clays, the former consisting essentially of quartz, and the latter of kaolin and limonite.1

Jan 5, 1915

By R. H. Hiltz, R. W. Douglass

Large-grain specimens of iodide titanium prepared metal-lographically were stain etched using the technique of New York University as modified by Watertown Arsenal Laboratories. Orientations of grains showing an abnormal response to stain etching were determined by back-reflection X-ray techniques. X-ray results showed that a-titanium grains, oriented such that their basal planes were parallel to the polished surface, have a slower reactivity to stain etching than any other orientation. Grains oriented such that their basal planes made small angles with the polished surface exhibited reaction rates between that of the true basal orientation and the normal rate. As the angle with the surface increases the reactivity increases up to a maximum angle of 14 deg. Basal planes making an angle with the surface of greater than 14 deg show normal reactivity to stain etching. These data, plus work on polycrystalline specimens, indicate that the oxidation rate of titanium might be reduced by correct alignment of crystal planes. ThE earliest observed phenomenon in the micrography of titanium was the occurrence of a grains which exhibited no birefringency. Even though a titanium possesses a hexagonal-close-packed structure and should be optically anisotropic, it can appear optically isotropic, when the crystal is so oriented that its intersection with the polished surface is perpendicular to the axis of symmetry. During the develoment of color staining techniques for titanium: it was noted that the a phase did not stain uniformly. Staining of specimens of commercially pure titanium resulted in a micro-structure of blue-colored grains, among which were randomly oriented a few grains exhibiting colors between the initial yellow and the final blue color. Under polarized light, these off-colored grains appeared to be optically isotropic. More intense study with polarized light, however, showed only the yellow grains to be isotropic. The intermediate colored grains exhibited weak birefringency, which at first glance is not detectable due to the strong birefringency of the surrounding structure. Aminoff2 and Straumanis3 have previously shown that in zinc the basal orientation is less reactive than other orientations. Leidheiser4 showed the same thing to be true for the hexagonal-close -packed configuration of cobalt. Thus, it would appear that the basal-plane orientation is responsible for the abnormality in stained titanium. Later work by Leidheiser5 on cobalt has shown that other planes besides the basal plane exhibited reaction rates slower than the normal rate. Reported planes were the (100), the (1011) and several planes making small angles with the basal plane. The last observance appears not to be due to the reactivity of the reported plane but due to the reactivity of the basal plane which is very close to being parallel to the surface. There are, then, two possible explanations for the range of colors observed in stain-etched a titanium. Since extensive research on the effect of orientation on surface reaction has failed to provide any definite trend, these two explanations are not adequate in themselves. Planes showing the retarded reactivity differ not only for different crystal structures but for metals of the same crystal structure and even for different reactions of the same metal. Tragert,6 Leidheiser,7 Tammann,6 and wagner9 have shown copper to exhibit retarded reactivity on the (111) plane. However, Leidheiser10 has shown that under other conditions the retarded reactivity of copper is associated with the (100)

Jan 1, 1960

By Larry Kaufman, Joan B. Berkowitz-Mattuck, Edward V. Claugherty

The oxidation characteristics of hafnium and zirconiunr diboride were measured between 1200 and 2200'K by a thermal- conductivity method which continuously ttzeasures the rate of reaction of oxygen with the diboride and by a metallographic air oridation method zuhich provides a measure of the total arr7ount of bovide conuerted to oxide for a given time interval. The oxidized specimens obtained from the tl~eritaal-coi~ductitrity method were also examined by quantitatire metal-lographic procedares. The significant results obtained in this investigation reveal that metal-rich compositions of lzafi~iutil diboride proride the most oxidation-resistatzt material up to 2000°K; hafnium diboride is tmre oxidation- resistant titan zirconium diboride at all tempevatures examined; the morphology of the oxide formed on H/B2 and Llie temperature coefficient qi. the oxidation rate constants change at the temperature of ttze monoclinic to tetragonal phase transition] in HfO2; the oxidation of neither HfB2 nor ZrB2, results iN catastrophic Jazlure at lorc. oxygen pressures; and pvefevetztial gvaLti boundary oxidation was not obsevued for either HfBi or ZYB, A comprehensive study of the high-temperature characteristics of refractory transition-metal di-borides is currently in progress. This program has included investigation of the physical, thermal, and thermodynamic properties of TiB2, ZrB2, HfB2, NbB2, and TaB2. In addition, aspects of the synthesis and fabrication of such materials have been studied. In view of the diverse nature of this research, a number of other laboratories have actively participated and contributed specific capabilities for analysis and characterization of these materials. As a consequence, an extensive description of the relevant properties of these compounds has emerged which is central in evaluating their high-temperature (1200" to 2500°K) performance. To date, information on thermodynamic stability, specific heat, and vaporization characteristics,1 hot hardness and electrical resistivity,1, 3 therma1 expansion:'4 and thermal conductivity 1, 5 has been presented. This information has been generated on materials of the highest purity (98.5 to 99.9 wt pct Me + B) and density currently available. Samples fabricated by zone melting6 and high-pressure hot pressing"3'7 techniques have been used to generate suitable specimens for all of the aforementioned studies. dation characteristics of the most oxidation-resistant of these materials, hafnium and zirconium diboride, is presented and a description of the synthesis and the experimental procedures used to prepare and characterize specimens is given. The high-temperature range under consideration (1200" to 2200°K) and the known dependence of oxidation characteristics on sample chemistry, density, and oxidation conditions required a close coupling of the synthesis, fabrication, and evaluation procedures.8 This was accomplished by continual surveillance of chemical composition of starting materials before and after specimen fabrication and by evaluation of density, phase constitution, and microstructural features prior to and after oxidation exposure. I) PROCUREMENT AND CHARACTERIZATION OF STARTING MATERIALS In view of the current state of the art in fabricating refractory boride materials, the methods used in preparing samples for the present study are given in detail as follows: starting materials were purchased in high-purity powder form and fabricated by high-pressure hot pressing into 0.40 by 1.00 in. bars from which oxidation specimens were obtained. The hafnium diboride used in this study was purchased from Wah Chang Corp.; the zirconium diboride from U.S. Borax and Chemical Co. These powders were routinely characterized by quantitative chemical analyses for metal, boron, carbon, oxygen, nitrogen, and iron, by qualitative emission-spectrographic analysis for trace impurities, by X-ray procedures for extraneous phase identification, and by powder densitometry for comparison with X-ray (theoretical) density. Hafnium and zirconium metal and elemental boron were also purchased as high-purity powders and characterized for impurities by emission-spectrographic analyses. The hafnium diboride was procured in three shipments which were designated as HfBl.g7(1), HfB1.88(2A), and HfB2.12(2). The indicated stoichiometry is based on the atomic ratio of total boron to total hafnium; the number in parentheses identifies the shipment number. Shipment 1 was 5 1b, shipment 2A, 1 1b, and shipment 2, 8 1b. The zirconium diboride was procured as a 20-1b shipment and designated as ZrB1.89(1). A small quantity of purified zirconium diboride was also supplied and designated ZrB1, 9(P). The averaged results for chemical analyses which were generally performed according to the procedures set forth in the compilation by KrieGe9 are presented in Table I. Qualitative spectrographic analyses indicated that Ca, Cr, Ti, Si, Zr (in H~B~), and A1 were present at levels between 0.01 and 0.10 wt pct. Other metallic elements were found to be less than 0.01 wt pct. Since it is virtually impossible to purchase these materials in the desired quantities (5 to 20 lb) as single-phase compounds it is necessary to obtain

Jan 1, 1968

By J. E. McDonald, J. G. Eberhart

A model is discussed from which the work of adhcslon .tor liquid transition metals on aluminum oxide surfaces can he calculated, A close-packed (00011 oxygen surface on A12O3 is assumed with two different types of surface sites: one type involving metal-oxygen bonds and the other man der Waals into actions. The work of adhesion is thus expressed as the sum of these two bonsding free energies. Calculated works of adhesion for nickel, titanium, chromium, and zirconium on sapphire agree well with the experimentally determined quantities. The model is extentled to the calculation of the work of adhesion and shear stress required to remove a thin metal film from a sapphire substrate and is in good agreement with experimental values. The obsewed dependence of the work of adhesion on the free energy of oxide formation of the metal is shown to also provide an interpretation of the tittle dependence of thin-film adhesion. THIS paper presents a model for the type of bonding which occurs across a metal-A12O3 interface. The model is used to explain the results of two types of experiments in which such an interface exists: 1) the adhesion of thin metal films on Al2O3 substrates and 2) the wetting of A12O3 by liquid metal drops. The adhesion of thin films to various substrates has been the subject of a variety of investigations.'-' Benjamin and weaver3 and Bowie,6 using the scratch test developed by Heavens,10 studied the adhesion of metallic films to glass substrates. Their observations for noble-metal film adhesion agree well with an adhesion model involving a van der Waals type of bonding between the film and the substrate. For films of metals whose free energy of oxide formation. ?F°f, has a negative value. Benjamin and weaver3 and Bowie6 found a time-dependent adhesion with an initial value that can be interpreted in terms of van der Waals interactions but a larger terminal value which was related to ?F°f, Karnow-sky and Estill7 deposited films on sapphire at elevated temperatures and noticed no time dependence of film adhesion but a similar correlation with ?F°f. Because of the kinetic problems associated with thin-film adhesion it is desirable to examine adhesion in an equilibrium system. The wetting behavior of liquid-metal drops on Al2O3 provides such a system. Systems of this metal-ceramic type have been studied extensively.11 Humenik and Kingeryl2 have measured the wetting of A12O3 (and other substrates) by several metals and have pointed out that the wetting ability of these metals increases with increasing values of -?F°f. It is thus seen that thin-film adhesion and metal wetting on A12O3 are both related to the tendency of the metal to react with the surface oxide ions of the Al2O3 substrate and, because of this, both phenomena should be explainable by an appropriate model for the metal-Al2O3 interfacial bonding. In the sections that follow, wetting and adhesion data on A2O3 are reviewed and a model is presented by which these phenomena can be interpreted. ANALYSIS OF WETTING EXPERIMENTS In an equilibrium system involving a liquid-metal drop on a solid Al2O3 substrate, the work of adhesion, WAD, is defined by the Dupre, equation as WAD = ?s + ?L -?sL [1] where ?s and ?L are the surface free energies of the solid substrate and the liquid drop, respectively, and ?sL is the interfacial free energy. The work of adhesion is the work required to separate a unit area of the solid-liquid interface into two surfaces. The work of adhesion is usually determined from a sessile-drop experiment in which yL and the contact angle, ?, are measured. The Young-Dupr6 equation is then used to calculate WAD Wad = ?L (1+ cos ?) [2] The literature of this subject has been examined and Table I shows work of adhesion data for various liquid metals as measured on A12O3 substrates. The standard free energy of oxide formation of the metal at the temperature of the wetting experiment, ?F°f . is also tabulated in kcal per g-atom of oxygen. The data is grouped according to the gaseous atmos-

Jan 1, 1965

By C. G. Rhodes, D. Kramer

The kinetics of precipitation of transient a phase during the transformation in U-16 wt pct Mo between 400° and 550°C were studied using quantitative metallography and electrica1 resistiuity measurements. The volume percent of a phase goes through a maximum in time, corresponding to a critical degree of progress of y' formation. prior to its re-solution after prolonged annealing. The fastest rate of a precipitation oc-cuvs at 500°C with a concomittant lowest peak of 9.5 vol pct a. At 450°C, 14 vol pct a, greatest fov any temperature, was observed after 24 hr witlz an associated slowest rate of formation. a precipitation at 400°C ceases after approximately 160 hr and the amount of a present remains unchanged after long times at temperature; no y' was observed metallographically at this temperature. IN the U-Mo system at 16 wt pct Mo, an ordering reaction takes place below 600°C, see Fig. 1, whereupon the random bcc solid solution, y, transforms to the ordered bct phase, y'."2 The new unit cell is constructed of three old unit cells somewhat distorted. While attempting to study the kinetics of this transformation it was observed that an unexpected phase was precipitating out early during the transformation anneal reaching appreciable amounts before disappearing after long times. The y' appeared in the presence of this new phase and after long times constituted the whole sample. Owing to the high optical activity of this unexpected phase under polarized light, it was suspected to be the a phase. Subsequent X-ray powder pictures confirmed this belief. The kinetics of a phase formation and disappearance is the subject of this paper. EXPERIMENTAL PROCEDURE A) Alloy Preparation. Alloys for this study were prepared by vacuum induction melting normal reactor grade uranium and 99.5 wt pct Mo pellets in thoria crucibles. Two ingots were prepared, and sections of the top and bottom of each ingot were chemically analyzed for uranium and molybdenum content. The results of the analyses appear in Table I. B) Metallography. Samples of 16M were wrapped in tantalum foil, sealed in evacuated (5 X 10"6 mm of Hg) quartz capisules, and annealed at 1110"C prior to being transferred directly to the transformation temperature. They were examined metallographically after increasing times to determine the progress of the transformation at 400°, 450°, 500°, and 550°C. The samples were prepared for metallographic examination by mechanical polishing with diamond paste and electrolytic polishing with a solution of glacial acetic acid and chromic acid. Since the y' phase is tetragonal, its presence can be detected by viewing the sample in polarized light. To increase the contrast between y' plates, the samples were electro-etched in a 10 pct oxalic acid solution. To reveal a phase in bright field (it can be seen in polarized light in the "as-polished" state), the samples were electro-etched in a solution of citric acid and nitric acid. To determine the vol pct a phase, a variation of the one dimensional systematic point count method as described by Hilliard and cahn3 was used. The

Jan 1, 1962

By J. D. Wright

INTRODUCTION The Endako deposit was first explored in 1926, but development waited until the early nineteen sixties. It first came under the control of Placer Development in 1963, and early in 1964 a decision to bring it into production was reached. The deposit is located near the geographic center of British Columbia, and is served by an east-west communication system including a paved highway, mainline railway and good telephone, teletype, and computer facilities. The plant area is shown in Figure 1. The operation is known as the Endako Mines Division of Canex Placer Limited of Vancouver. First production was achieved in June, 1965, at a nominal rate of 10,000 tons per day, but it soon was closer to 15,000 tons per day. In 1967, two new grinding and flotation, sections brought capacity to the present rate of approximately 27,000 tons per day. With mill heads of around 0.15 percent MoS2, production is about 14,000,000 pounds of molybdenum per year. A flowsheet of the operation is given in Figure 2. A legend for this flowsheet is given in Table 1. Published ore reserves are estimated at 214,500,000 tons at an average grade of 0.143 percent MoS2. PRIMARY CRUSHING The 85 or 100-ton haulage trucks dump over a grizzly into a 42 inch x 65 inch C.A.C. (Canadian Allis Chalmers) gyratory crusher. The

Jan 1, 1976

By Craig E. Saporito

INTRODUCTION Freeport-McMoRan Inc. has been very active recently with two major discoveries and its restructuring activities. This paper describes Freeport-McMoRan's businesses, the two major mineral discoveries, and exciting opportunities within the oil and gas operations. BUSINESS ACTIVITIES Freeport-McMoRan is the largest and one of the lowest cost fully integrated U.S. phosphate fertilizer producers. It is the second largest domestic Frasch sulphur producer. Freeport- McMoRan will become the largest domestic producer of Frasch sulphur when its Main Pass Block 299 sulphur deposit reaches full production in 1993. Furthermore, it is the largest transporter of sulphur produced by others. Its oil and gas activities rank among the largest U.S. independents in terms of production and proved reserves. The copper/gold operations in Indonesia are among the world's lowest cost. When expansion operations reach full capacity levels in 1992, the Indonesian copper/gold complex will be the fifth largest copper operation in the world. Operations are divided into three business segments that include: 1. Agricultural minerals, incorporating sulphur, phosphate rock and phosphate fertilizer activities; 2. Energy, including oil and gas activities; and 3. Metals, incorporating copper, gold and silver operations in Indonesia. In early 1989, Freeport-McMoRan announced the discovery of two world-class ore bodies; a sulphur deposit off the coast of Louisiana on Main Pass Block 299, and a copper/gold deposit -- the Grasberg in Indonesia -- approximately two miles away from the existing Ertsberg East operations. As a result of these major discoveries, Freeport- McMoRan decided to carry out a restructuring program. Its purpose was to sell $1.2 to $1.5 billion of non-strategic assets. Debt levels and associated interest expenses will be significantly reduced, and general and administrative expenses will be reduced, which will place Freeport- McMoRan in an excellent position to fund the development of the Main Pass Block 299 sulphur discovery, the Grasberg discovery, and oil and gas discoveries. This restructuring program also will allow Freeport-McMoRan to achieve the greatest future value for shareholders by focusing on its principal businesses (Figure 1). Strategic Restructuring • Sell $1.2 - $1.5 Billion Of Non-Strategic Assets • Significantly Reduce Debt • Significantly Reduce G&A • Fund Development Of Main Pass & Grasberg • Stronger Company; Positioned For Future Growth • Focus Is On Principal Businesses: - Sulphur/Phosphate Fertilizers - Indonesian Copper/Gold - Oil And Natural Gas Figure 1 - Strategic Restructuring AGRICULTURAL MINERALS Main Pass Block 299 Discovery The Main Pass Block 299 discovery has a proven reserve of 67 million long tons of recoverable sulphur. This is the largest known Frasch sulphur deposit in North America. The discovery increased Freeport-McMoRan's sulphur reserves more than five-fold, and is synergistic with the company's phosphate fertilizer assets. The

Jan 1, 1990

By R. R. Estill

THE rank of the Ruhr coal ranges from a high volatile bituminous coal to an anthracite, depending to some extent on the original depth of the seam. The average Ruhr coal corresponds to a soft bituminous American coal of a coking quality. The average thicknesses of individual coal seams being mined are also comparable (59 in. against 65 in. in the United States). However, consideration of seam conditions and mining conditions other than those just mentioned emphasizes differences rather than similarities with United States soft coal. In general, the Ruhr seams now being mined are much more folded and inclined than American seams. Dips of 20" and 30" are common in seams now being worked, and 30 pct of the coal reserves in the district are in seams dipping more than 35". Only on the tops and bottoms of folds do we find rather flat coal seams. In addition to the folding there is extensive displacement by cross faulting plus a certain amount of strike faulting of an overthrust nature, which results locally in doubling or omission of seams. Because of the long history of mining in the Ruhr, nearly all coal lying near the surface has long since been mined out, and we find that the average depth of mining is at present about 2300 ft below the surface. Deep mining, folding, and faulting result in seam conditions requiring a great deal more roof support than one finds in American soft coal mines. In fact only in the anthracite district and the Rocky Mountain and Pacific coal fields do we find somewhat similar conditions. It is easy to say, therefore, that the problem of mechanization of coal cutting and loading in the German mines is quite different from that which we have so effectively met in America with our mobile cutters and loaders, duck bill loaders, and a room and pillar system of mining our drift and slope mines.

Jan 12, 1950

By Laurence W. Casteel

Indian Creek Mine, newest of the St. Joseph Lead Co. properties, is located in southeast Missouri on the flanks of a buried porphyry ridge. Here the orebodies are very irregular in size and shape and have a regional pitch of about 15°, which may vary locally from 0 to 90°. To maintain an economical grade of ore, selective mining is imperative. The room and casual pillar method is employed with 20-ft diam pillars 35 ft apart where possible. Stopes vary in height from 10 to 55 ft. All are too small to supply a loading unit continuously.

Dec 1, 1956

By Erhard Hornbogen

Twins were propagated into large, well-annealed crystals of a, iron-phosphorous and a, iron-molybdenum solid solutions. Strain fields caused by interaction of these twins were made visible by precipitation. These strain fields can be explained by assuming that transmitted and reflected plastic waves are created when a twin strikes an obstacle with high velocity. The twin front itself can be regarded as a shear wave that may be able to develop a one-dimensional shock front. The occurrence of {WO} fracture by the reflected stress is also discussed. The described effects were not found when twins propagated at lout velocity into disturbed crystals, for example, into crystals previously deformed by slip. DEFORMATION twinning leads to shearing of a crystal lattice under external load. The shear appears to be homogeneous over a large number of crystal layers. In a iron, shear occurs on the (112) planes and in the <1ll> directions. The formation of a twin proceeds by the movement of partial dislocations that change the stacking at the twinning plane.l, In the bcc lattice, this partial dislocation can be created by dissociation of a sessile a/2[111] dislocation that lies in the (112) plane: Cottrell and Bilby&apos;s spiral mechanism can explain the homogeneous shear, but has not been proven experimentally. Nevertheless, this mechanism can explain the possible high velocity of formation of a twin. In Cottrell and Bilby&apos;s model, as in other models of twinning or phase transformation, a much higher energy is required to spread the first stacking fault than to add new layers by further movement of the partial dislocations. The dislocations will therefore become accelerated proportional to the difference between the stress, tN, to nucleate and tp to propagate the twin. It has been assumed3,4 that tn is the stress required to make two partial dislocations of apposite sign pass for the first time. After the first layer of new stacking has been formed, the maximum stress is TN=Gb/4pd where G is the shear modulus, b is the Burgers vector of the partial dislocation, and d is their perpendicular spacing so that the amount of shear is S = b/d. From this formula, a value of 25 kg per mm2 has been estimated for twinning in Zn3. The measured values are smaller, but local internal stresses may help to provide the necessary stress. For a iron, a higher value can be expected, mainly due to the higher value of G. That agrees with the observation that "burst" twinning occurs if the yield strength is in-

Jan 1, 1962