Search Documents

By E. T. Turkdogan, M. T. Hepworth, R. P. Smith

The permeability of oxygen in 0 iron in the tempera-ture range 700" to 900 C and in 6 iron at 1450°C was determined by the rate of internal oxidation of iron, containing -0.1 pct Al. The solubility of oxygen in zone-refined iron was determined by equilibration with hydrogen-water vapor gas mixtures at 1450" and 1510°C; oxygen solubilities , for iron in equi1ibriu.rn with molten oxide, are found to be 66 and 83 ppm for these two temperatures, respectively. The diffusivity of oxygen in iron at 14500C3 as calculated from the permeability and solubility data, is (4.1 * 0.6) x 10 "B sq cm per sec. OXYGEN is one of the most common impurities present in iron or steel, mainly in the form of oxide inclusions. In the study of many metallurgical problems concerning solid iron, it is often desirable to know with a reasonable accuracy the solubility and diffusivity of oxygen over a wide temperature range. The solubility of oxygen in solid iron has been the subject of numerous studies yielding highly discordant results as seen for example from the literature surveys made by Meijering &apos; and Schenck et a1.&apos; As shown by Kitchener et aL3 and by Sifferlen, the high oxygen solubilities reported by many investigators are the result of oxidizable impurities which are often present in iron. In addition, there have been experimental problems associated with icaccuracy of oxygen analysis of iron containing less than 100 ppm 0. A number of studies have been made on the permeability of oxygen in a and y iron using Fe-Si, Fe-Mn, and Fe-A1 alloys in the internal-oxidation experiments.1&apos;2&apos;5&apos;6 However, no direct measurements have been made of the diffusivity of oxygen in iron. In the present work two sets of experimental measurements were made: permeability and solubility studies at 1450" and 1510°C and permeability studies only in the range 700 to 900°C. In both sets of permeability measurements slab-shaped specimens containing small predetermined amounts of aluminum in solution were exposed at constant temperature to gas mixtures of hydrogen, water vapor, and argon for varying times. These specimens were quenched, sectioned, and examined for oxygen penetration by metallographic observation of aluminum oxide particles which formed. From these data, it is possible to calculate the ratio of the diffusivity of oxygen in iron, D, to the equilibrium constant K for the reaction Hz(g) * O (dissolved in iron) = H,O(g). EXPERIMENTAL Permeability Measurements at 1450°C. An ingot of vacuum-carbon deoxidized iron containing 0.086 pct A1 was prepared, using commercial "Type lO4A Plas-tiron"; after hot rolling, specimens were machined into slabs a by 2 by 2 in. The impurity contents were: S, P < 0.002 pct; C, Mn < 0.01 pct; each of all other Usual impurities < 0.004 pet. The amount of oxide inclusions in this material, determined by a bromine-methyl acetate extraction, corresponded to about 20 ppm 0 in the iron which agreed well with the results of vacuum-fusion analysis. Each specimen was annealed at 1450°C for 1 hr in purified hydrogen, polished to a smooth surface, and then introduced into a controlled oxidizing atmosphere in a recrystallized alumina tube at 1450°C. The constant temperature zone (*3"C) was about 3 in. in length. The gas composition was controlled by mixing argon with hydrogen (using calibrated constant-head flow meters) and passing the mixture through a column of a mixture of oxalic acid dihydrate and 10 pct anhydrous oxalic acid, to establish a required water-vapor content in the gas mixture. The temperature of the oxalic acid dihydrate column was controlled by a thermostat. The total gas flow was in the range 800 to 1000 cu cm per min. The exit gas from the reaction tube was passed through a weighing bottle containing a desiccant, to cross-check the degree of water-vapor saturation, which for all experiments was about 97 pct of those derived from the data of Baxter and Lansing.1 For a typical experiment, a specimen was introduced into the furnace in a stream of dry argon and hydrogen. The specimen was then rapidly raised by a Pt-Rh alloy wire into the hot zone and allowed to reach the reaction temperature, at which time the oxidizing gas mixture was introduced. The oxygen potentials employed were sufficient to oxidize aluminum but not to cause liquid iron oxide to form. After a specified time, the experiment was ended by dropping the specimen onto a water-cooled copper block at the bottom of the reaction tube. The depth of the internally oxidized zone, hereafter called the "case", was determined by sectioning the specimen at right angles to the long direction. The section was then examined under a microscope equipped with a micrometer stage. In general, the oxide particles were fairly uniform in size and distribution, forming a reasonably well-defined interface between the oxidized and unoxidized region. A typical cross section as observed at X30 is shown in Fig. 1. A thermal macroetch was used in one selected specimen to delineate the case. A cross section of a previously oxidized slab was polished and reheated at 1450°C in a hydrogen atmosphere for about 10 min. Upon quenching, the surface relief shown in Fig. 2 was produced; causes of this effect are unknown. Permeability Measurements Below 900°C. A slightly

Jan 1, 1967

By R. W. Smith, Z. Sadowski

The stabilities of finely divided mineral suspensions were determined as functions of pH and concentrations of polyethylene oxide, sodium ligninsulfonate, sodium dodecybulfate, and sodium oleate. In addition, the electrokinetic potentials of the minerals were determined under identical pH and additive concentration conditions. Flocculation or dispersion of the suspensions is discussed in terms of both the amount and manner of adsorption at the appropriate solid-liquid interface as it is influenced by additive concentration and pH.

Jan 1, 1986

By J. E. Warren, J. H. Hartsock

In the receipt of J. E. Warren and J. H. Hartsock&apos;s comments on our paper, "Aspects of Gas Deliverability", We wish to point out that all the physical characteristics we conceived as constant were absorbed in the gas deliverability constant of the individual well&apos;s performance, listed

THE paper on "Specific Efficiency of the Blast Furnace" by Richard Franchot, which was pub-lished in the September issue of MINING AND METALLURGY, was presented for discussion at the Pitts-burgh meeting. The session opened with a discussion among S. P. Kinney, Mr. Franchot, and J. N. Reese as to the methods and results in sampling for cyanides in the blast furnace. This is covered in detail in writ-ten discussion below. T. T. Read objected to the use of the term specific efficiency as likely to be confusing. The blast furnace has to perform the function of reducing Fe, 03 to Fe as well as that of fusing the metal and, since the reduc-tion of Fe, 0? involves a CO equilibrium, it seems mis-leading to calculate efficiency on the basis of burning the , all carbon to CO? since it is not possible. Mr. Franchot replied that he used the term in the sense defined by Richards in his "Metallurgical Calculations;" but a subsequent search failed to reveal the term in Richards, who says (page 245, 1st edition): The practical conclusion is that a blast furnace generates in itself not much over 40 per cent of the calorific power of the fuel used, and rejects nearly 60 per cent; by using part of the waste gases to heat the blast, however, some of this rejected heat, to an amount representing net 5 to 10 per cent of the calorific power of the fuel used, is returned to and injected bodily into the furnace, thus rendering available for the purpose of running the furnace about 50 per cent of the calorific power of the fuel as a maximum. The efficiency with which the furnace applies this 50 per cent usefully to the objects of the reducing and smelting is another question for investigation.

Jan 2, 1927

By T. S. West

Completion and production data presented for three wells in the Oakville area of Live Oak County, Texas, which were completed near the gas-oil or water-oil contact, indicate that coning may not be as prevalent a cause of failure in such cases as is commonly assumed. Failure in the cases discussed is indicated to be due instead to: (I) erosion of the formation, (2) flowing out of mud filter cake, or (3) failure of the cement. An open-hole gravel-pack type of completion procedure is proposed for preventing failures of this kind by preventing movement of all solid material in the space in which completion is made. Various combinations of layers of gravel, sand, and cement are utilized for this purpose. Experimental results and theoretical discussion as to the applicability of gravel pack completion are included. Introduction This paper is primarily a study of the reasons for failure of oil-well completions near the gas-oil or oil-water contact, and suggests a procedure for increasing the efficiency of this type of completion. The value of improvement in completion effectiveness near the gas or water zone is not confined, however, to wells of relatively thin oil columns. Thick oil columns become thin as depletion progresses. It would seem to follow that the minimum distance from the gas or water zone at which completion can be made in a new well indicates the limit to which depletion may be carried in a well having an oil column of any initial magnitude. Only four ways can be postulated in which high gas-oil or water-oil ratio can initially occur if the zone exposed for production is within the oil column: 1. Failure of the cementing material. 2. Vertical coning. 3. Failure along the boundary between the cement and the wall of the well. 4. Failure of the formation comprising the wall of the well. Cementing materials such as portland cement and plastics have reached a high stage of development. Failures of this type are probably due almost always to extraneous causes such as mud contamination rather than to faulty cementing material. Vertical coning can and obviously does occur. However, the usual occurrence of thin impermeable streaks in sand sections and the success with which open-hole drill-stem tests can be made near the gas-oil contact suggest that over-all effective vertical permeability, and in turn vertical coning, is less prevalent than frequently is assumed. Much has been written on failure by flowing out of the mud filter cake between cementing material and the formation. A filter cake is always present if, prior to cementing, mud has come in contact with a permeable formation at pressures exceeding the pressure head of the fluid it contains. Mechanical methods are in use for removing filter cake during the cementing operation? which undoubtedly are of

Jan 1, 1947

By T. S. West

Completion and production data presented for three wells in the Oakville area of Live Oak County, Texas, which were completed near the gas-oil or water-oil contact, indicate that coning may not be as prevalent a cause of failure in such cases as is commonly assumed. Failure in the cases discussed is indicated to be due instead to: (I) erosion of the formation, (2) flowing out of mud filter cake, or (3) failure of the cement. An open-hole gravel-pack type of completion procedure is proposed for preventing failures of this kind by preventing movement of all solid material in the space in which completion is made. Various combinations of layers of gravel, sand, and cement are utilized for this purpose. Experimental results and theoretical discussion as to the applicability of gravel pack completion are included. Introduction This paper is primarily a study of the reasons for failure of oil-well completions near the gas-oil or oil-water contact, and suggests a procedure for increasing the efficiency of this type of completion. The value of improvement in completion effectiveness near the gas or water zone is not confined, however, to wells of relatively thin oil columns. Thick oil columns become thin as depletion progresses. It would seem to follow that the minimum distance from the gas or water zone at which completion can be made in a new well indicates the limit to which depletion may be carried in a well having an oil column of any initial magnitude. Only four ways can be postulated in which high gas-oil or water-oil ratio can initially occur if the zone exposed for production is within the oil column: 1. Failure of the cementing material. 2. Vertical coning. 3. Failure along the boundary between the cement and the wall of the well. 4. Failure of the formation comprising the wall of the well. Cementing materials such as portland cement and plastics have reached a high stage of development. Failures of this type are probably due almost always to extraneous causes such as mud contamination rather than to faulty cementing material. Vertical coning can and obviously does occur. However, the usual occurrence of thin impermeable streaks in sand sections and the success with which open-hole drill-stem tests can be made near the gas-oil contact suggest that over-all effective vertical permeability, and in turn vertical coning, is less prevalent than frequently is assumed. Much has been written on failure by flowing out of the mud filter cake between cementing material and the formation. A filter cake is always present if, prior to cementing, mud has come in contact with a permeable formation at pressures exceeding the pressure head of the fluid it contains. Mechanical methods are in use for removing filter cake during the cementing operation? which undoubtedly are of

Jan 1, 1947

By F. E. Jaumot, R. L. Smith

Self-diffusion in zinc has been used as an instrument for comparison of the absorption and sectioning techniques as a means of studying diffusion. Single crystal as well as poly-crystal samples were used asanda the temperature range of diffusion extended from 200° to 415°C. For temperatures above 200°C, the data indicate that the results obtained from the absorption technique agree with those obtained from the sectioning technique. The effect on the values of the diffusion coefficient of electroplating vs evaporation as a means of applying the tracer was investigated and no significant difference observed. It was found that an excess or deficiency of tracer did not materially affect the results obtained from the sectioning technique, but invariably caused errors with the absorption technique. NEARLY all self-diffusion experiments and many alloy diffusion experiments have employed radioisotopes as the instrument for following the diffusion. Of the various techniques in which radioisotopes are applicable, the two most widely used are the sectioning and absorption techniques. In the former, the diffusion coefficient is obtained from a curve of log concentration vs the square of the mean penetration depth. In the latter, the diffusion coefficient is calculated from a knowledge of the decrease in activity at the surface after diffusion. In spite of the importance of knowing the reliability of the diffusion data and the widespread use of these two techniques, they had not been directly compared experimentally on the same samples. Thus, such a comparison was worthwhile. The specific system chosen for this comparison was the self-diffusion of zinc, since the metal was readily obtainable in high purity, single crystals were easily grown, and the anisotropic features of the diffusion added an additional factor of interest to the comparison. Self-diffusion in both single and polycrystals was investigated, since the possibility existed that grain boundaries and grain boundary diffusion might produce different effects for the different techniques. Also, the effects of electroplating vs evaporation as a means of applying the radioactive tracer, and the effects of applying an excess or deficiency of tracer material were studied. The general experimental procedures and the mathematical analyses of both techniques have been described previously in some detail, and only those points essential to an understanding of the present work will be discussed here. The mathematical analysis of the sectioning data requires only a knowledge of the solution of Fick&apos;s equation. where C,, is the initial concentration, C is the concentration at depth x, D is the diffusion coefficient, and p is the absorption coefficient of the solvent metal for the radiation from the solute. Having obtained F from the experiment, the value of z can be read from a plot of F vs In z, and D can then be calculated if is known. The necessity of knowing the absorption coefficient causes most of the criticism of the absorption technique. It is very difficult to measure accurately under the conditions existing in the diffusion experiment, but it is absolutely necessary, as will be indicated briefly later. Portions of this problem have been discussed in detail elsewhere." The difficulties involved in the measurement of the absorption coefficient arise from three principle factors: the physical characteristics of the absorber, the geometry, and complex radiation spectra. The first two are heavily dependent upon the third. If

Jan 1, 1957

By S. M. Wu, R. L. Stone, T. D. Tiemann

The dissolution of silica from quartz in sodium hydroxide solutions was investigated by statistical methods. A second-order predicting equation was developed with 28 experiments expressing the dissolution of silica as a function of the variables quartz size, time, temperature and sodium hydroxide concentration. With this equation a comprehensive picture of the dissolution reaction was gained which included the effect on extraction of each variable and their interactions, fractional extractions, reaction rates and activation energies. A previous investigation of the extraction of silica from low grade siliceous iron ore by digestion in sodium hydroxide solutions presented the extraction as a function of time, temperature and sodium hydroxide concentration.&apos; The present paper is an outgrowth of the previous work and develops by a mathematical analysis the functional relationship between the extraction of silica and time, temperature, sodium hydroxide concentration and particle size. Relatively pure quartz was used in this study in order that the basic quartz-sodium hydroxide reaction could be studied without the influence of other constituents that are commonly found in iron ores. The functional relationship between the dissolution

Jan 1, 1965

By Henry M. Howe

The object of the present paper is to suggest injecting into the hearths of iron blast furnaces, whose temperature has become unduly lowered, some form of fuel whose calorific intensity, under the peculiar conditions existing there, is considerably higher than than of liquid petroleum, the rose of this substance for melting out chills having grievonsly disappointed the high hopes which were at first entertained of it. A chill being a fall of the temperature below that needed for the complete liquefaction of the slag, which requires, according to Plattner, about 1800&apos; C., one would suppose that the chief thing to be accomplished in curing it would be to raise the temperature in the crucible of the furnace. The most obvious ways of doing this seem to be to raise the temperature of the blast, and to increase the amount of fuel in the crucible itself. Simply increasing the rate at which the blast enters the furnace, if carried beyond a certain point, should lower the temperature in the crucible. The existence of a chill shows that the fuel is arriving too slowly at the tuyeres. If air be introduced so rapidly as to he in excess of that required for the combustion of the fuel, all that excess will simply lower the temperature around the tuyeres, carrying the region of intense heat upwards, and weakening its intensity by increasing its size. Up to a certain point, increasing the rate of introducing the blast will increase practically pari passu the rate at which the fuel reaches the tuyeres. But when mechanical obstructions, which so often accompany chills, retard the descent of the fuel, there must be a point beyond which this does not hold good, and beyond which farther

Jan 1, 1883

By Frank F. Aplan

In looking into the crystal-ball scene of minerals beneficiation for 1970 and beyond, an impartial observer becomes con- fused as to what has been done and what is possible in the way of improvements. The mining official must balance the burden which is being shouldered by the mineral industry for maintaining our environment in its pristine state on one hand, with the solid advancements made in technology and cost savings on the other hand. Then the official wonders if this is really the criterion for judging overall performance today. As a prospective engineer, Dave Bolles sees it this way: "Specialization has caused many engineers to subordinate everything to doing their job the cheapest and fastest way. In the future this won&apos;t be enough. The engineer in the mineral industry will be responsible not only for mining, concentrating and smelting, but also for the resultant wastes- the mine dumps, the tailing dams and the slag piles." (See Drift on page 63).

Jan 1, 1971

By R. J. Wagner, F. F. Craig, H. G. Riley, J. D. Griffith

Peripheral water injection has been underway in the Sholem Alechem Fault Block "A" Unit, Stephens County, Okla., since 1955. In the engineering planning of the flood, it was recognized that maintenance of pressure in the large, dry gas caps was vitally necessary to prevent the loss of an estimated 27 million bbl of oil through saturation of the gas caps by the oil banks moving updip on the peripheral flood pattern. The development of an abundant, low-cost water supply and the rising cost of makeup-gas purchases indicated that gas-cap control by water injection was desirable from an economic standpoint, provided an eflective water barrier could be placed without premature water breakthrough into downdip oil producers. A laboratory model scaled to the existing reservoir conditions was comtructed to evaluate the feasibility of gas-cap water injection. Model studies indicated that (I) water injected at the edge of the gar-oil contact would form a continuous barrier between the oil and gas zones, and (2) water would advance uniformly downdip without segregation due to gravity effects provided a specified, minimum water-injection rate was maintained. The model test results also indicated that it was not necessary to fill the gas cap completely with water. Water injection at the edge of one of the gas caps was initiated in March, 1958, to field test gas-cap water injection. Water breakthrough occurred at a downstruc-ture producing well in April, 1959, after approximately 2.5 million bbl of water had been injected into the gas cap. This was the volume calculated to be required to form the barrier between the oil zone and gas cap. This performance indicates that prevention of oil encroachment into dry gas caps in a peripheral water flood by water injection at the gas-oil contact appears practical and that the model studies provided a valid prediction of field performance. INTRODUCTION The Sholem Alechem Fault Block "A" Sims Sand Unit was one of the fist major waterflood projects in Oklahoma to utilize a peripheral injection pattern. Design of control measures to minimize oil encroachment into the large crestal gas caps was one of the greatest single problems during engineering planning of this flood. Engineering studies indicated that saturation of the gas caps with oil displaced by the peripheral water flood could result in a loss of about 27 million bbl of oil, or over one-half the estimated waterflood recovery. This estimate was based on a residual oil saturation after water flooding of 35 per cent pore volume, compared to the negligible oil saturation initially in the gas caps. The Sholem Alechem Springer field, located in Stephens County, Okla., is an elongated anticline with structural dips varying from 400 to 1,000 ft/mile. The structure contains numerous faults, some of which are sealing. The portion of the field considered in this paper is Fault Block "A", which is the largest of the five major fault segments in the field. A map of the unit is shown on Fig. 1. The unit is bounded on the east and west by major sealing faults, on the north by a water-oil contact and to the south by a deterioration of sand development. Two domes, each having gas caps, exist in the unit and are separated by a north-south fault as shown in Fig. 1. The sands being flooded are the Sims sand members of the Springer series of early Pennsylvanian age. The Sims sands average over 100 ft in thickness in Fault Block "A" and have a porosity of approximately 19 per cent. Core permeabilities average 160 md, with interstitial water saturation of about 23 per cent pore volume. Three different zones can be correlated over most of the area. However, they are commingled in most of the producing wells. The two upper zones, designated as First and Second Sims, are the most important. Both the First and Second Sims have gas caps in the east dome, while only the First Sims has a gas cap in the west dome. These gas caps, whose limits are also shown on Fig. 1, initially occupied nearly 11 per cent of the total reservoir volume. The major concern of this paper is the control of the two gas caps in the First Sims sand. Fig. 2 is a cross section, to scale, across the east dome of this formation. Notable features are the relatively shallow dip, the deterioration of the First Sims sand on the south side of the gas cap and the water-oil contact on the northern edge. The formation dip at the gas-oil contact in this cross section is approximately 5".

By A. E. J. Engel

INDUSTRIAL talcs and ground soapstones both include earth materials of different chemical and mineral compositions. In general, the industrial talcs are composed of silicates that contain appreciable amounts of magnesia. Generally talc, the mineral, is a predominant or at least common constituent. Talc, the mineral, is a hydrous magnesium silicate, with a suggested theoretical formula H2Mg3 (SiO3)4 or H2O.3MgO.4SiO2, which postulates 63.5 pct SiO2, 31.7 pct MgO, and 4.8 pct H20.11 Actually different single grains or leaves of pure talc have variations in water content ranging from 3.5 pct to more than 7 pct, as well as slight differences in the proportions of MgO and Si02.16 Only a very small percentage of the ground industrial talcs produced in the United States approaches the composition given above (see Table 1). The purer talcs invariably occur as alteration products of magnesium carbonate rocks. Some of these relatively pure talcs include compact, massive types largely mined in California, which are designated as steatite.38,58 In general, steatites cannot contain in excess of 1.5 pct CaO, 1.5 pct combined FeO and Fe203, and 4 pct A1203. The less pure varieties of massive talc and mixtures of magnesian silicates are commonly called soapstones, or merely talc. Many industrial earth products classified as talc or as soapstone contain a variety of minerals, especially serpentine (H4Mg,Si2O9), chlorites (hydrous magnesium, iron, aluminum silicates), tremolite (Ca2Mg5H2[SiO3]8), anthophyllite ([MgCa]SiO3), diopside (CaMg[SiO3]2), and quartz (SiO2). The carbonates calcite (CaC03), dolomite (CaMg[CO3]2), and magnesite (MgCO3) are also present in some industrial talcs and soapstones. Some of these minerals, as well as sulphides, sulphates, and iron and manganese oxides, if present at all or in excess of minute amounts, may alter the composition of the industrial talc sufficiently to restrict materially its use or to lower or destroy its value. These factors are discussed in a subsequent section of this chapter.

Jan 1, 1949

By W. A. Doble

Opinions differ as to whether the water-wheel almost universally known as the Pelton type belongs to the impulse, the tangential, the reactive, the jet or the percussion class, or to a cross between two or more of these classes. The fact is, that for an almost infinitesimal part of a second the axis of the jet of water strikes the bucket of this wheel at a true tangent to its base-line. The percussion of the water, striking the bucket, imparts an impulse to the wheel, causing rotation; and generally the bucket is so shaped that the direction of the jet is

Jan 1, 1900

By J. M. McDowell

A study has been made to deter~r~irre how the behavior of a water drivee reservoir changes as a function of the permeability of the formation and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rote of nat11rn1 water influx is also studied, (IS well as the influence on the influx of the position of water injection we1ls with reference to the oil-water contact. The results are determined by the use of an electrical reservoir analyzer and are plotted as families of curves of pressure, natural water influx, and water injection vs time or cumulalive production. Two size aquifers are studided. One is limited with a 36-inile radius, and the, other approximates an infinite reservoir. The field remains the same in all respects for the completed. study except that the permeability is changed to agree with that assumed for the aquifer. 1 N TR ODUCTI ON this study was undertaken in -dcr to determine how the pres- sure decline and water influx of a water drive field would change as a function of the rate of fluid withdrawals, as a function of the permeability of the formation, and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rate of natural water influx was also studied as was the position of water injection wells with reference to the oil-water contact. The information has been determined by the use of an electrical reservoir analyzer1, sometimes referred to as a Carter type analyzer. This instrument is an analog type computer which can be set up to represent a water-drive oil field. It can reproduce the past performance of the field in terms of analogous electrical quantities when the proper circuit analog of resistors and condensers has been determined, also, it can determine the future behavior for any method of production which may be selected, or permit the comparison among several different methods. Although most applications of the reservoir analyzer"" have been to thc study of specific field performance, it is intended to use the analyzer here to help understand how various reservoir characteristics effect the final performance of the field and to sec under what conditions water injection will be of benefit and to what extent. Within the oil industry the performance of water-drive reservoirs was first described analytically by LV. Hurst&apos; and M. Muskat2 for certain types of boundary conditions. The solutions of the equations developed involved products of exponential functions and Bessel functions. Later publications by Hurst4 and van Ever-clingen" and the hooks of Muskat6 gave further information on reservoirs with other boundary conditions. They also presented rather extensive curves and tables to help evaluate the analytical expressions involved. A rccent series of publications by Chatas. bascd on the work of Hurst and van Everdingen, gives quite complete charts and tables of data to evaluate the pressure decline or water influx in infinite or limited radial reservoirs. and in linear reservoirs. The curves in all of these publications are given in dimensionless form

Jan 1, 1956

By Alfred F. Beasley

The slags derived from the smelting of lead and copper ores are composed essentially of silicates. The problems arising from the smelting of these ores consequently involve the study of silicate fusions. In the absence of specific knowledge concerning the compounds occurring in slags, it has been the practice of metallurgists to treat them in terms of their total chemical composition. Slags have been classified as monosilicates, bisilicates, sesquisilicates, and subsilicates according to the relative amounts of oxygen in the acid and basic radicles of the hypothetical salt produced. While this has been a useful guide to metallurgists in computing the furnace charges, it falls far short of a basis for the scientific investigation of slags. In order to understand the nature of a slag as a whole it is necessary to learn the physical and chemical properties of the mineral compounds which go to make up that slag. The efficiency with which an ore is smelted in a furnace depends primarily on the physical properties of the compounds formed during the operation. When the melting points and fields of stability of each of the mineral compounds in slags have been established, it will be possible to determine the properties of any given slag by examining the nature and amounts of its mineral constituents. Earlier Investigations In 1884 and succeeding years an extensive survey of lead and copper furnace slags was made in Europe by Vogt, and a large part of the present knowledge of the subject is due to his publications.&apos; Vogt&apos;s interest in artificial fusions was directed primarily towards the explanation of problems in igneous and economic geology and his subsequent works have been confined wholly to that subject.

Jan 1, 1930

By N. S. Stoloff, M. Gensamer

The effects of temperature, grain size, and magnesium content on the strength and ductility of cadmium were studied in the range -269° to 23 °C. A sharp drop in ductility between -140° and -190°C marked a transition in fracture mode from ductile shear to inter gvanular fracture. The addition of up to 15.35 wt pct Mg in solid solution raised the transition temperature, and for two compositions produced basal cleavages. The relatively high ductility of unalloyed cadmium at cryogenic temperatures is attributed to temperature independence of the yield stress and the absence of dislocation locking. ALTHOUGH numerous studies have been made of the mechanical properties of cadmium single crystals,1-5 no comprehensive investigation of deformation and fracture in polycrystalline cadmium has been carried out. This investigation was initiated to determine the mechanisms of deformation and fracture in polycrystalline cadmium, and to attempt to correlate these mechanisms with the behavior of other metals of hexagonal close-packed structure. A second objective of this work was to determine whether the slip systems and mode of fracture of polycrystalline cadmium could be altered by reduction of the axial ratio, which is 1.886, through alloying. Dorn and co-workers&apos; have been able to induce prismatic slip in magnesium through alloying to reduce the axial ratio. Single crystals of cadmium are so highly ductile that glide strains of 400 pct are observed at room temperature, and 80 pct at -269°c.l Failure in every reported case is by necking down and shearing off of the crystal. Cleavage in cadmium single crystals has never been observed. Magnusson and aldwin reported a ductile to brittle transition for polycrystalline cadmium at about —160 C for specimens tested at a strain rate of 0.05 in. per in. per min in tension. However, even at -196° substantial ductility was retained. The transition temperature was strain rate dependent, impact loading at 19,000 in. per in. per min raising the transition temperature to about -85°C while leaving the low temperature ductility unchanged. No information was given on microstructures or fracture mode, nor were stress-strain characteristics reported. In the present investigation, tensile tests were carried out on polycrystalline cadmium and solid solution Cd-Mg alloys to determine flow stresses, work-hardening behavior, fracture strength, and fracture ductility. Variables employed included temperature, alloy content (and c/a ratio), and grain size.Some compression data also have been obtained for comparison purposes. I) EXPERIMENTAL PROCEDURES A) Polycrystalline Cadmium. Two purities of cadmium were employed in this investigation. Cadmium of 99.95 pct purity was supplied by Belmont Smelting and Refining Co. Cadmium of 99.99+ pct purity was supplied by American Smelting and Refining Co. Threaded cylindrical tensile specimens were machined to give approximately a 1/2 in. long straight gage section with a reduced diameter of about 0.110 in. Specimens were heat treated in evacuated pyrex capsules in the range 140" to 290°C to produce desired grain sizes. All specimens were polished in a solution containing 320 g Cr03 and 20 g NaS04 in 1000 cc of H20. Occasionally this solution caused staining of the specimen, in which case a further polish with a solution of one part HN03 and two parts H202 in two parts ethyl alcohol was employed.&apos; Tensile testing was carried out on a screw-driven Instron machine, at a constant rate of crosshead movement, which for most tests was 0.01 in. per in. per min. Load vs time, and therefore load vs total strain, were recorded. Temperatures from -196" to -40°C were obtained by passing nitrogen gas through a copper coil immersed in liquid nitrogen, and then feeding the gas into a jacket around the specimen. Tests at -269°C were carried out in a helium cryostat, at a crosshead rate of 0.1 in. per in. per min, with specimens of 1 in. gage length. Compression specimens were tested in a jig similar to one designed by ilman. The jig was mounted on the under side of the Instron crosshead. Load was transmitted by means of a rod connected to a movable part of the jig at one end, and the load cell at the other end. A downward movement of the crosshead applied a compressive load to the specimen.

Jan 1, 1963

The term "timbered stope" is here meant to denote stopes in which timbering is the predominant feature of the mining method. Stopes with stull sets, as in the Hecla mine, are types of timbered stopes; these types are probably the best-known. Timbering stopes by means of square sets is not as common as formerly, as the system is not often necessary, yet there are good examples and large tonnages are being mined by the method. The square set may be utilized in ordinary overhand stopes if the orebody is suitable. At some mines, square sets have been abandoned in favor of top-slicing; and at others, the square set has superseded horizontal cut and backfilling. A drift, either in the wall or orebody, is necessary before opening the sill floor. In wide deposits, there may be a grillage of drifts and crosscuts, and at least one raise to the level above is needed in each stope for ventilation and handling timbers and filling. The square sets are filled with waste rock from the hanging wall, sorted from the ore, from development work, or from the level above. As a rule, little timber is recovered. The examples include the Butte district, Mother Lode of California, Bunker Hill & Sullivan, Hecla, and Morning mines.

Jan 1, 1925

By J. R. Long, R. S. Dean, F. S. Wartman, E. T. Hayes

The production of titanium in I5-lb. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,&apos; has provided adequate material for a study of the physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited&apos; and all efforts were centered on fabrication methods for those powders and the proper- ties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. Consolidation of the PowdeR The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at 50 tons per

Jan 1, 1946

By J. R. Long, E. T. Hayes, R. S. Dean, F. S. Wartman

The production of titanium in I5-lb. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,&apos; has provided adequate material for a study of the physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited&apos; and all efforts were centered on fabrication methods for those powders and the proper- ties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. Consolidation of the PowdeR The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at 50 tons per

Jan 1, 1946

By H. F. Korman, M. C. C. Mow, P. K. Dai

INTRODUCTION Detonations of high explosives in soil and rock have been used frequently in civil engineering applications. Of particular interest in recent years has been the development of test methods to simulate the desired blast and shock environments for the testing of protective structures. The United States Air Force, in particular, the Air Force Weapons Laboratory, in conjunction with the Defense Atomic Support Agency, has in recent years, developed special technology for simulation testing of protective structures in soil and rock media. Such a technology, although initially developed for military applications, is rapidly finding its way into civil applications. One of the major problems in the design of the simulation test is the correct prediction of ground motion induced by the detonation of high explosives. This paper presents a useful prediction method which is developed specifically for ground motion in rock that is induced by the detonation of a buried planar array of explosive columns (See Figure 1). The technique of simulating shock environment using such an array is called the Direct Induced High Explosive Simulation Tech- nique (DIHEST). Normally, each shot hole may contain canisters of ammonium nitrate positioned at various depths, or a slurry explosive with detonators positioned along its length (See Figure 1). The depth and width of the array, the spacing of shot holes, the spacing of detonators, the degree of containment, and the charge weight are the variables which govern the induced ground motion

Jan 1, 1971