Search Documents

By N. A. Gokcen

THE data of Chaudron,1 Tonosaki,2 and Collins³ on the thermodynamic properties of MOO, disagree widely. These authors, by using essentially similar methods, studied the following reaction: 1/2MoO2(s) + H2(g) == i/2Mo(s) + Ph,o H2O(g),K = —----- [1] Ph2 Tonosaki used a vacuum system consisting of a furnace containing MOO, and a water saturator whose temperature was kept at 25 °C with a thermostat. After repeated evacuation, hydrogen was admitted slowly into the system. The experiments were based upon the fact that at a constant furnace temperature and constant partial pressure of water, the total pressure of gas mixture over MOO? + Mo is constant. Any attempt to vary the pressure by external forces would vary only the amounts of MoO2, and Mo, after which the pressure should return to the equilibrium value in accordance with the equilibrium constant of reaction 1. The actual value of K was determined from the total equilibrium pressure (sum of Ph2o + Ph2) at each temperature. The total pressure of gas was varied within the range of 80.2 to 125.4 mm Hg, within a temperature range of 645" to 823 °C. The results were summarized as log K = 0.9413 — 1444.6/T for reaction 1. The ratio of H2O/H2 was considered to be uniform in spite of the presence of a thermal gradient across the static gas phase. It was shown by Rosenqvist and Cox,' however, that in somewhat similar circumstances the error resulting from thermal diffusion may be large. Collins³ improved Tonosaki's method by attempting to avoid thermal diffusion errors. His equilibrium data were obtained at 700°, 800°, and 900° C, and the result for reaction 1 was expressed as log K = 1.258 — 1822/T. The purpose of this investigation was to study reaction 1, avoiding the thermal diffusion errors, and to obtain equilibrium data in a considerably wide temperature range for the reliable extrapolation of the resulting thermodynamic functions. Experimental Procedure The diagram of the apparatus is shown in Fig. 1. Tank hydrogen was passed through a tube containing platinized asbestos at 425 °C in order to convert a trace of oxygen into water vapor. The flow rate was carefully controlled with a capillary-type flow-meter B and a bubbling column D. The gas was then presaturated sufficiently at P and led into a condenser system immersed in a thermostat, controlled to within ±0.002C. The temperature of the thermostat was measured with a thermometer calibrated against a certified standard. The temperature of P was adjusted to avoid the condensation of unduly large amounts of water as judged from the rate of flow out of the capillary tube M. Argon was purified by passing it through magnesium chips kept at 630°C. After passing through the flowmeter B', it was mixed with moist hydrogen emerging from the thermostat. The resulting gas mixture was then led into the hot zone of the furnace through the heated glass tubing and the silica tube S, thus insuring the same ratio of PII2o/Ph2 from the condenser to the reaction chamber, thus avoiding thermal diffusion. The entire gas system was of all-glass construction, except at the magnesium train. The furnace comprised a glazed alumina tube over which a 15-in. platinum coil was wound. The lower end of the alumina tube was tightly closed with a brass bottom and a silicone rubber gasket, and the upper end with two glass disks, each with a hole of 1/16 in. in diameter, through which the gas mixture escaped into the atmosphere. A back-up coil of kanthal wire facilitated the temperature control of the furnace. A coil of annealed molybdenum strip of 99.99 pct purity, 0.005 in. thick and 0.050 in. wide, and weighing 17 g was hung in the furnace with a 0.010-in. platinum wire attached to one end of a sensitive analytical balance. The temperature of the furnace was measured with a Pt-Pt-10 pct Rh thermocouple checked against a standard. The experimental procedure consisted of heating the gas purification trains, adjusting the gas flow rates, attaining a constant thermostatic temperature, flushing the entire system for 2 hr while heating the furnace to well above the expected equilibrium temperature and then cooling it at a rate of 0.3°C per min during which time the change in the weight of molybdenum was observed on the balance. For a given thermostatic temperature, i.e., a constant Prr,o/Px,, molybdenum oxidized upon cooling slightly below the equilibrium temperature. The procedure was then repeated by heating the furnace and thus reaching a temperature slightly above the equilibrium value. The average of the two temperatures, differing by 2" to 3"C, was considered to be the true equilibrium temperature. In order to determine the stoichiometric composition of the oxide phase present in this investigation,

Jan 1, 1954

By B. E. Eakin, A. L. Lee, M. H. Gonzalez

Expeximental viscosity and density data of lour natural gases are presented for temperatures from WO to 340F and pressures from 100 to 8.000 psia. A correlation is also discussed and results reported. INTRODUCTION This investigation is one of several efforts by the authors to provide viscosity data for pure hydrocarbons and mixtures. Results of some pure hydrocarbons and their mix tures have been presented." Several predictive methods and correlations have also been reported.'," This paper presents the experimental viscosity and density data of four natural gases and confirms a correlation in a previous study. APPARATUS The viscometer was described previously. 2,6 A bank of stainless steel pycnometers was included to determine density in conjunction with the viscosity measurements (Fig. I). DATA AND MATERIALS The natural gases were furnished by the Atlantic Richfield Co. (Samples 1 and 21, the Continental Oil Co. (Sample 3) and the Pan American Petroleum Corp. (Sample 4). Table 1 shows the composition of these gases obtained by mass spectrometer analysis. The pure component viscosity data used in the correlation have been published."".'"', '" Experimental and calculated viscosity data for the natural gases are presented in Tables 2 through 5. CORRELATION Starling and Ellington"' have reported several semi-empirical expressions based to a certain extent on the theory of viscosity advanced by Born and Green.' The final expression presented by Starling and Ellingto'n is: i'. (micropoise) -- /t,, exp rX(7') p ..... (I) Eq. 1 was modified by Lee et 01." to represent mixture and pure component data simultaneously. This equation has the form: F = K exp [XpY] :.........(2) where K=- (7.77 i 0.0063M)Ti 122.4 + 12.9M +T .................(3) ' ' ' X= 2.57 + ---1914.5+ 0.0095M .... (4) Y = 1.11 -r 0.04 X ........(5) Over the pressure and temperature range studied in this investigation, this equation represents the data on methane, ethane, propane, n-butane and four methane-n-butane mixtures with a standard deviation* of ? 1.89 per cent. Density data by Sage and Lacey" were used to fit the equations. Eq. 2 gives reliable values of the viscosity of light hydrocarbons without prior knowledge of experimental viscosity values, but accurate density data must be available. Eq. 2 was used to predict viscosity values for the natural gases studied in this paper. The particular set of parameters contained in Eqs. 3 through 5 gave values that reproduced experimental data within 25 per cent. Needless to say, in using Eq. 2 better density values will give better viscosity results. However, those engineers who do not have accurate density values at hand or the time, or such facilities as a library, computer, etc. readily available, may feel uneasy in using Eq. 2. Therefore, the authors sought the easiest but by no means best density prediction method, which was reported by Kaf 30 years ago. A set of density values, which were calculated based on Kay's method, and a generalized compressibility factor chart were used to fit Eq. 2. The results are:

Jan 1, 1967

By Wilford Stork

CERTAIN influences of oxygen on iron have been known for many years and it has always been considered one of the worst enemies of the iron and steel founders. Nobody had a good word for it, hence little was done to make use of this oxygen. In all the fields of foundry practice, the desideratum was "melt without oxidation of the metal." In the consideration of the influence of oxygen on cast iron, we must not confuse this condition with oxidized iron caused by poor melting conditions, due to a high bed, heavy charges, low coke ratio, excessive melting rate, high blast, or poor charging. It is admitted that oxygen absorbed by iron melted under these conditions has a deleterious effect on the properties of the iron. The writer has had experience both in the melting under such poor conditions and in remedying these bad conditions and considers the product far inferior to iron melted under normal conditions. As stated by Dr. Richard Moldenke,1 such iron has a higher melting point and high combined carbon, is sluggish, and contains slags and oxides in solution in the liquid, causing slag inclusions and gas occlusions, thus producing defective castings. This oxidized condition cannot be counteracted or removed by any of the known deoxidizers; it can be remedied only by proper melting conditions. Such iron is really burned, whereas the iron considered in this paper was melted under normal conditions with moderate blast, correct bed height, light charges of iron, and low coke consumption and is not in this category at all. In 1914, the late J. E. Johnson, Jr., startled the metallurgists of the world when he published his results on the advantages of oxygen on cast iron.2 His work is so convincing and so logical, in spite of the common and well-established notions on the subject, that nobody has been able to refute a single argument. Such an eminent authority on iron and steel metallurgy as Prof. H. M. Howe has accepted the work in all its details in his latest book3 The work of J. E. Johnson, Jr., has revolutionized

Jan 6, 1919

By J. E. Fox Jr., J. L. Lummus, J. P. Gallus

Fresh water or brine drilling fluids may be kept free of suspended drilled solids by the addition of a water soluble acrylamide-carboxylic acid copolymer at the flowline. Addition of from .01 to 0.2 lblbbl of the polymer solution to drilling fluids containing less than 5 per cent clay solids by weight causes the solids to flocculate and settle rapidly to the bottom of the pits. Solutions of the polymer injected at the pump suction reduce the loss of water to permeable formations without impairing the permeability to oil. The use of drill-itlg fluids clarified with the polymer has resulted in increased drilling rates, extended bit life, and lower drilling fluid costs. INTRODUCTION Field experience and the results of a number of investigations have established that the accumulation of solids in drilling fluid reduces drilling rate.'-' Drilling with water makes possible higher drilling rates than can be achieved with mud but in many areas drilling with water may not be feasible because of the possibility of encountering high formation pressures or by-dratable formations. To combat these conditions, the drilling fluid must possess certain physical properties such as viscosity, density, fluid loss, etc., which require the presence of solids. The current trend in drilling fluid treatment is to maintain as low a percentage of solids as is possible without harmfully affecting the mud properties needed for drilling. Mechanical separating devices such as wet cyclones and decanting-type centrifuges are proving to be an economical means of controlling the percentage of solids and thereby maintaining low solids muds. Also: special muds have been developed for the purpose of retarding the hydration of drilled solids so that they may be more easily removed by shale shakers or settling pits. In some areas, such as West Texas, the characteristics of some formations will permit drilling with water. However, because of the dispersion of drilled solids, it is usually not possible to maintain clear water even with the aid of mechanical separators, or by utilizing large settling pits. For this reason the commonly used term "water drilling" is a misnomer since the water usually contains some solids. Because of the improved drilling rates and other benefits which might be effected, a laboratory and field study was made of the use of flocculating agents for maintaining clear water for drilling. PROCEDURE Laboratory—Solids Settling Two techniques were employed to determine the effectiveness of flocculating agents in settling solids from drilling mud. First, the rate of fall of solids was measured in graduated beakers containing mud treated with various flocculating agents. Natural gum, oil-in-water emulsions prepared with ethoxylated nonyl phenols and diesel oil. and a powdered synthetic acrylamide-carboxylic acid copolymer* (hereinafter referred to as "polymer") were tested as flocculating agents in both fresh water and salt saturated muds containing 4 per cent solids. The polymer was not added in the powder form directly to the muds but was first dissolved in water in a concentration of 3.5 lb/bbl. The polymer solution was then added directly to the mud. The concentration of the flocculating agents, including the polymer, was varied. High rates of fall of the solids indicated high flocculating efficiency. A second technique consisted of measuring the time in minutes required to obtain clear water at the pump suction after addition of the various flocculating agents at the flowline. These tests were made using a model mud circulating system having a total volume of approximately 10 gal. The natural fresh water and brine muds used contained 4 per cent solids. A sketch of the circulating system appears in Fig. 1. The circulating rate

By H. C. Schultz, F. K. Middleton Hunter

Certain local conditions were known to govern in large measure the successful adaptation of liquid-oxygen explosives to the large-scale blasting at Chuquicamata. The wide variation in hardness of the rock at this mine makes necessary the use of several types of explosives. A locally manufactured, relatively cheap black powder is used in blasting the softer waste and capping material, where a thorough displacement breaks the ground sufficiently. Before the introduction of L. 0. X., an ammonia dynamite of about 65 per cent. strength was being used exclusively in the harder underlying orebody, where a strong disruptive as well as a displacement effect is required for breaking the ore. The L. 0. X., as developed for quarry work in the United States, has a practically pure carbon cartridge material, and the explosive has an extremely high rate of detonation, which should therefore cause it to develop usefully its full disruptive effect in hard ground. The individual blasts at Chuquicamata arc large, black-powder shots which dislodge masses of rock averaging 250,000 tons each, and dynamite shots which dislodge masses averaging 80,000 tons each. It was desirable, therefore, to attempt to displace with L. 0. X. the faster, higher-cost ammonia dynamite used in the smaller blasts. It was not considered practical to attempt to displace the low-cost black powder with 1,. 0. X., as estimated costs showed no probable saving if this were accomplished. Since it was desirable to continue shooting relatively large blasts for effective operation, it was recognized that larger storage facilities than had been in use would be needed for the liquid oxygen. Because of the difficulty of transporting and discharging large storage containers of efficient design, the better plan appeared to be storage and discharge of the liquid at the place of manufacture, and transportation of the filled soaking boxes to the blast. Present Liquid-oxygen Plant An experimental unit with a rated capacity of 75 liters per hour was erected during the latter part of the year 1926 to prove the effectiveness of L. 0. X. at this mine, its cost, and possible efficiency of large-scale storage of the liquid. With this experimental unit 200,000 tons of ore

Jan 1, 1928

By A. D. Taylor

In recent years there has been an increasing effort to attract students into engineering. Obviously, the effort is necessary because young people find the image of the engineer unattractive. Some of the things they find unattractive are real, some are not, and part of the problem is too little knowledge of the field. First, I would like to comment on some of the ideas which appear to be justified. Engineering is a difficult course of study. True, and nothing can or should be done to change this. The education is continually being improved, but it is unlikely to be made easier.

Jan 1, 1970

By J. F. Emig

The Burns Harbor Plant was designed to produce and process large ingots into plate, hot rolled sheet, cold rolled sheet and tin plate. Rimmed ingots, in particular, are poured 96" to 106" high and weigh up to 85,000 lbs. During the latter part of 1970, a quality problem was encountered involving white line "sliver" defects on the surface of cold rolled, low carbon, rimmed steel sheet. Sheets containing these defects are not desirable for exposed automotive items because of the possibility of opening during forming or becoming more apparent after forming. Metallographic work located and identified two basic types of inclusions within the white line defects: (1) complex oxides consisting largely of iron and manganese oxides and (2) scale-type iron oxide. The presence of these oxides strongly suggested that the-white line defects were resulting from an unsound, unclean rim zone.

Jan 1, 1972

Jan 1, 1937

By Michael Tenenbaum, T. L. Joseph

Recent researches on the reduction of iron ores have stimulated interest in the effect of increased pressures within the iron blast furnace. From a physicochemical viewpoint, it seems logical to suppose that the increased pressure would increase the rate of reduction of the iron ore within the furnace. This increased reaction velocity would in turn be reflected in an increase in the output of the blast furnace. Any substantial effect of elevated blast-furnace pressures should accordingly be of both technical and economic interest to the operator. It is doubtful whether it is possible to increase the pressure in the stack of the blast furnace beyond two or three atmospheres without incurring severe mechanical difficulties. The benefits to be procured by elevations in pressure must therefore be restricted to pressures below two, or at the most, three atmospheres. Within this range it would seem both economically and mechanically feasible to modify the present design of the upper portion of the blast furnace to accommodate these more stringent operating conditions. This investigation was undertaken to study the effect of moderate pressures on the rate of reduction of iron ore with hydrogen. The use of carbon monoxide is contemplated for later work. Although any results that are obtained in the laboratory cannot be interpreted directly in terms of large-scale commercial operations, it is possible, through such an investigation, to ascertain the order of magnitude of the effects of higher pressure. A more quantitative conception of the effects that would result from the use of increased pressures in the modern blast furnace is needed. In some recent work, Diepschlagl found that, all other factors remaining constant, the degree of reduction of iron ores was much greater when carried out under pressure. Pressures as high as seven atmospheres were used. The degree of reduction was determined from the ferrous and ferric iron in the sponge iron. Results were obtained using both carbon monoxide and hydrogen at temperatures of 400°, 600° and

Jan 1, 1939

By Michael Tenenbaum, T. L. Joseph

Recent researches on the reduction of iron ores have stimulated interest in the effect of increased pressures within the iron blast furnace. From a physicochemical viewpoint, it seems logical to suppose that the increased pressure would increase the rate of reduction of the iron ore within the furnace. This increased reaction velocity would in turn be reflected in an increase in the output of the blast furnace. Any substantial effect of elevated blast-furnace pressures should accordingly be of both technical and economic interest to the operator. It is doubtful whether it is possible to increase the pressure in the stack of the blast furnace beyond two or three atmospheres without incurring severe mechanical difficulties. The benefits to be procured by elevations in pressure must therefore be restricted to pressures below two, or at the most, three atmospheres. Within this range it would seem both economically and mechanically feasible to modify the present design of the upper portion of the blast furnace to accommodate these more stringent operating conditions. This investigation was undertaken to study the effect of moderate pressures on the rate of reduction of iron ore with hydrogen. The use of carbon monoxide is contemplated for later work. Although any results that are obtained in the laboratory cannot be interpreted directly in terms of large-scale commercial operations, it is possible, through such an investigation, to ascertain the order of magnitude of the effects of higher pressure. A more quantitative conception of the effects that would result from the use of increased pressures in the modern blast furnace is needed. In some recent work, Diepschlagl found that, all other factors remaining constant, the degree of reduction of iron ores was much greater when carried out under pressure. Pressures as high as seven atmospheres were used. The degree of reduction was determined from the ferrous and ferric iron in the sponge iron. Results were obtained using both carbon monoxide and hydrogen at temperatures of 400°, 600° and

Jan 1, 1939

By R. E. Reed-Hill, J. L. Martin

Kinking is an important deformation phenomenon in poly crystalline a zirconium. The crjlstallo-gvaphic features of the most important form of kinking have been determined with the aid of twins formed at 77°K in grains previously kinked at high temperatures. It has been .found that the kink-band boundaries correspond to walls of edge dislocations with (1150) Burgers vectors and dislocation lines parallel to (1070). The present observations imply that basal slip is an important secondary-slip mode in polycrystalline zirconium. Previous single-crystal studies13 did not veveal this mode Other evidelzc.e for (0002)(1120) slip is also presented. ThE first studies of kinking in hexagonal metals were made by orowan,1 using single-crystal cadmium wires. He suggested that this was a new de- formation mode in metals, different from ordinary glide or twinning. Next, Hess and Barrett2 studied zinc-crystal rods in compression, and were able to offer an explanation of the phenomenon described by Orowan. They concluded that kinks required no new deformation mechanism and were a special form of deformation band that developed gradually and solely from basal glide. Similar kink bands were then observed by Washburn and parker3 on zinc crystals deformed in tension at low stresses and high temperatures. In titaniun,4 kink bands associated with {1010}<1120> prism slip have been observed in coarse-grained specimens. Magnesium5 and rhenium6 have also been observed to kink in conjunction with their basal- and {1010} prism-slip systems, respectively. Yttrium has (1010) as a predominant slip plane, but no observations of kink bands were reported.7 Since no previous investigations of kink bands in zirconium have apparently been made, this study was proposed. Its aim was to determine the crys-tallographic features of a type of kink band frequently observed in polycrystalline zirconium. EXPERIMENTAL APPARATUS All tests were performed on a type TTC Instron machine. The cross-head speed usually chosen in tension or compression was 0.02 in. per min. Ten-

Jan 1, 1964

Jan 1, 1940

By W.M. Peirce

The present work has been done in an endeavor to correlate and complete the data on the constitution of alloys of zinc with other common metals, dealing exclusively, however, with the zinc-rich alloys in which the zinc content is between 90 and 100 per cent. This investigation has included the systems lead-zinc, cadmium-zinc, iron-zinc, copper-zinc, aluminum-zinc, nickel-zinc, manganese-zinc, cobalt-zinc, tin-zinc, and magnesium-zinc. The important ternary system zinc-lead-cadmium and the zinc corners of other ternary systems have been investigated in connection with this work but will not be dealt with here. Zinc does not form a single homogenous zinc-rich solid solution over any considerable range of concentration with any of the metals mentioned. A limited range of solid solubility is said, by previous investigators, to occur in several cases and certain effects on the properties of zinc are attributed (with varying degrees of consistency among different writers) to the presence of certain other metals dissolved in zinc. The increasing use of rolled zinc and the possibilities offered by zinc as a casting alloy in certain fields have made it essential to determine precisely these equilibrium relationships. In carrying out this investigation reliance was placed chiefly on two methods, conductivity measurements and microscopic analysis. The first method proved valuable in determining the existence and extent of solid solubility. The second method stands alone as a means of determining structural characteristics and supplements the first method in the measurement of solid solubility. The scleroscopic hardness of all conductivity specimens was measured partly for its value from the point of view of mechanical properties and partly as a check on the conductivity curves in indicating the limits of solid solubility. No hardness curves are included in this paper, for in no case were they important in arriving at the constitution of any system. Conductivity measurements were in all cases made on cold-rolled strips 0.020 in. thick and 0.5 in. wide, both as cold rolled and after an

Jan 1, 1923

By W. M. Peirce

The present work has been done in an endeavor to correlate and complete the data on the constitution of alloys of zinc with other common metals, dealing exclusively, however, with the zinc-rich alloys in which the zinc content is between 90 and 100 per cent. This investigation has included the systems lead-zinc, cadmium-zinc, iron-zinc, copper-zinc, aluminum-zinc, nickel-zinc, manganese-zinc, cobalt-zinc, tin-zinc, and magnesium-zinc. The important ternary system zinc-lead-cadmium and the zinc corners of other ternary systems have been investigated in connection with this work but will not be dealt with here. Zinc does not form a single homogenous zinc-rich solid solution over any considerable range of concentration with any of the metals mentioned. A limited range of solid solubility is said, by previous investigators, to occur in several cases and certain effects on the properties of zinc are attributed (with varying degrees of consistency among different writers) to the presence of certain other metals dissolved in zinc. The increasing use of rolled zinc and the possibilities offered by zinc as a casting alloy in certain fields have made it essential to determine precisely these equilibrium relationships. In carrying out this investigation reliance was placed chiefly on two methods, conductivity measurements and microscopic analysis. The first method proved valuable in determining the existence and extent of solid solubility. The second method stands alone as a means of determining structural characteristics and supplements the first method in the measurement of solid solubility. The scleroscopic hardness of all conductivity specimens was measured partly for its value from the point of view of mechanical properties and partly as a check on the conductivity curves in indicating the limits of solid solubility. No hardness curves are included in this paper, for in no case were they important in arriving at the constitution of any system. Conductivity measurements were in all cases made on cold-rolled strips 0.020 in. thick and 0.5 in. wide, both as cold rolled and after an

Jan 1, 1923

Jan 1, 1924

By D. J. Carney, C. W. Boquist, E. C. Rudolphy

Effect of variations in sinter feed composition on sinter strength, bulk density, re-ducibility, chemical composition, and microstructure were determined by sintering experimental samples on a production sintering machine. Increasing amounts of roll scale, ore fines, return fines, and blast furnace slag were most beneficial to feed permeability, sinter bulk density, and strength. Burnt lime additions improved feed permeability but were not beneficial to sinter strength or bulk density. Sinter reducibility was adversely affected by all additives. DEVELOPMENT of methods for evaluating sinter quality, which would in some way predict the behavior of the sinter during charging and smelting in the blast furnace, has been given considerable attention in recent years. In a previous investigation at South Works of the United States Steel Corp., standard sinter sampling and testing procedures were developed.1,2 By modifying the sinter sampling device, a method of sintering experimental mix sinter samples upon a production Dwight-Lloyd sintering machine was also developed. This technique afforded a rapid and controlled method of investigating the effects of the various raw materials and additives on sinter quality and was used in this present investigation. Since the beginning of the present study in 1953, the results of numerous sinter investigations have been published, most of which were concerned with production tests of iron ore sinter, both here and abroad. Three groups of investigators reported results of experimental sinter studies that were related to this investigation. Voice et al.3 studied the effects of controlled variables on sinter quality by producing and testing experimental Northants iron ore sinter using an experimental sintering unit. Mor-rissey and Powers&apos; determined the relationship between iron ore sinter quality and the moisture and coke content using a small laboratory sintering system. Burlingame et al.5 studied the effects of "additives" upon iron ore sinter using a laboratory sintering apparatus and laboratory grade raw materials. At South Works, it was considered desirable to study the effects of sinter mix composition and additives upon the quality of a flue dust-base sinter produced on a production sintering unit. Extrapolation of controlled laboratory test data to sintering plant operation lacking such precise control is not altogether satisfactory. Therefore, the present study was conducted in a manner which approximated production conditions as closely as possible. The raw materials used were those commonly encoun- tered in the production of flue dust and flue dust ore-type sinters and these were varied within extremes encountered in this type of sinter production. Experimental Procedure The experimental sinters were produced from 100 lb mixtures of sinter feed. The principal raw materials and additives used, their particle size, and approximate chemical composition are listed in Table I. The mixing of the raw materials was accomplished by means of a miniature single shaft pug mill shown in Fig, 1. The use of the pug mill as a mixer was decidea upon after encountering difficulty in reproducing the mixing and chopping effect of the sinter plant pug mill with other types of available small mixers. The miniature pug mill was constructed, consisting of 31/2x2x1/4 in, blades spaced 3 in. apart along a 3 ft shaft. Preliminary tests were run with this small mixer to establish the proper rotation speed and the required number of passes through the pug mill to thoroughly mix and distribute all the raw materials in a manner approximating the production Pug mill- Although the effects of varying the mosture content were determined in one particular series of tests, the amount of moisture added was changed as the composition of the experimental mix was varied. The aim in making water additions was to achieve a permeability as high as possible for each particular

Jan 1, 1956

By Charles Barrett

THE orientation of metal crystals and grains, both large and small,. can be determined conveniently and accurately without the use of X-ray apparatus. This seems to be appreciated by so few metallurgists that it may be useful to explain in detail the method we have found most satis-factory in the laboratory the reflection of light from crystallographic etch pits. This note includes a description of a suitable inexpensive instrument and instructions for etching various metals and for plotting the data. As the stereographic projection is used to facilitate handling the data, this note may be considered as an appendix to an earlier review of the metallurgical uses of the stereographic projection.1 Various methods involving etch pits have been used by other investi-gators, Bridgman&apos;s method2 consists of attaching the specimen to a sphere (a transparent sphere is convenient4), holding it at arm&apos;s length, and marking a spot on it when it has been turned so that the etch pits reflect light into the eye of the observer from a lamp standing behind him. It has an accuracy of about 2° and is extremely rapid. A greater accuracy can be obtained by having the reflected light fall on a screen, as has been done by Czoehralski, 5 Chalmers,6 and Schubnikov.7 All of these methods have been intended for undeformed single crystals. Tammann and his coworkers"&apos; developed a method for estimating the number of grains in a polycrystalline aggregate having orientations in a given region of the stereographic triangle and thus obtained statistical information about deformation and recrystallization textures. While the method has had some use in recent years,9 it is not applicable to the majority of problems in physical metallurgy. Smith and Mehl10 determined orientations by plotting the directions of the sides of individual etch pits on a stereo-

Jan 1, 1940

By W. E. Ruder

IT has been pointed out by Stead 1 that grains of considerable coarseness may be developed in steels containing from 3 to 5 per cent. of silicon, and in a previous paper 2 the present author has shown that under the proper conditions of annealing single grains having an area of 50 sq. cm. may be obtained. It is the purpose of this paper to discuss in more detail the conditions, promoting the growth of these grains, in the hope that the experiments described may throw some additional light upon the general problem of grain growth in metals. These silicon steels lend themselves particularly well to such experiments because of the ease with which the change in structure may be followed and because of the fact that the effect of the carbon present is largely obliterated by the high percentage of silicon. This forms a solid solution with the iron, which acts very much like a pure metal. This alloy has been found to have but one critical point, viz., Are. This point, determined by Roberts-Austen for Hadfield&apos;s 4 per cent. Si alloy, was found to lie at 703° C. Vigouroux3, in working with pure Fe-Si alloys, finds this point to rise from 750° C. for 0.5 per cent. Si to 860° for 6 per cent alloy, with a flat region in the curve from 3 to 4 per cent. Si. No accurate determination of this point has been undertaken by the present author, but it has been roughly determined to lie between 730° and 750°.

Jan 12, 1913

By Howard N. Eavenson

FROM the Pittsburgh coal bed in the four states of Pennsylvania, Ohio, Maryland and West Virginia has been produced an output that, at mine prices, represents a greater value than any other single mineral deposit in the world has yielded.12 While this distinction may in a few years pass to the gold reef of the Witwatersrand, it is possible that eventually, owing to the tremendous reserves still remaining, the ultimate yield of the Pittsburgh bed will be greater than that of any other known single deposit. Considering its importance, not a great deal has been written of its early history and development as a whole; most of the accounts have been of limited localities, or, at the most, of the area within a single state. In "Coal through the Ages" the writer mentioned some references to its early history, but this study will deal not only with its history but with the character of the bed, where and why it was first developed, and its effect upon the states in which it is found. It has not been the intention to write a detailed history of the development of the seam in each locality, as neither time nor inclination were available for doing such work, but only to show the influences that tended to hasten or retard such development. In general the historical matter ends about 1830, when geological surveys began to be made. Some of the maps show data available only since that time, and the sections about coal preparation and coking have been extended to the present time to show the changing conditions. It is believed that the early history includes all published records, and many more sources than those shown in the bibliography were consulted. It is quite likely that some references to coal in this area may be found in the unpublished papers of some of our early soldiers and colonizers, which exist in several libraries, and it is hoped that some future

Jan 1, 1938

By B. D. Cullity

A distribution of residual stress after plastic elongation is proposed, in which the bulk of the material is strained in compression and a very small portion in tension, This distribution is shown to account both for the X-ray observations and for the effect of plastic straining on magnetic losses in silicon steel. The regions left in compression are tentatively identified with the interiors of the sub-grains revealed by the electron microscope. THIS paper is concerned with the general problem of the nature of the residual stress which is produced in metals by plastic elongation. A particular stress distribution will be suggested which accounts for the main X-ray diffraction observations which have been made. It will also be shown that certain magnetic measurements made on silicon steel can be understood in terms of this stress distribution. X-RAY OBSERVATIONS Uniform straining of a crystal lattice (macro-strain) causes a diffracted X-ray beam to shift its position, and nonuniform straining (microstrain) causes line broadening. If a bar of metal is plastically elongated in the longitudinal x direction and then unloaded, diffracted X-ray lines are observed to be both shifted and broadened.&apos;-= Although the observed line shift indicates the presence of macro-strain, experiments have shown that no macrostrain, in the usual engineering sense of the term, exists.5"7 For example, removal of a layer from one surface of a stretched and unloaded bar does not produce curvature in the remainder of the bar 5&apos;7 Fig. 1 shows the variation of lattice strain in the x direction, as determined from X-ray line shifts, with the applied stress in the same direction. The curve ABC is the normal stress-strain curve of the material, AB being the elastic portion and BC the plastic. In the elastic region AB, the strain measured by X-rays, called the lattice strain, and the strain measured mechanically are both proportional to the applied stress, and both return to zero when the applied stress is removed. Above the elastic limit the lattice strain would be expected to continue to increase along the line BD. Actually, it increases less rapidly with respect to stress, or even decreases, as shown by BE. If the applied stress is then decreased, the lattice strain decreases along EF, which is parallel to AB. As a result, there is a compressive residual lattice strain FA after unloading. STRESS DISTRIBUTION. Since a stretched and unloaded bar does not contain macrostress, it follows that the observed line shift must be due to a special distribution of mi-crostress. Such a distribution is shown in Fig. 2, which shows the variation of the stress u, across a stretched and unloaded bar. The material is assumed to consist of two kinds of regions: regions C, stressed more or less uniformly in compression, comprising the bulk of the volume of the material and responsible for the observed diffrac-

Jan 1, 1963