Search Documents

Jan 1, 1946

Jan 1, 1920

By Benjamin F. Tillson

The hammer drill rightly receives the credit for having made the one-man drill possible, and so many economies seem possible through the proper application of different types of hammer drills to various mining, quarrying, and excavating operations, that an indication of the 'economies effected by the New Jersey Zinc Co. at its Franklin mines may be of pertinent interest. When this company commenced its trials of hammer drills in 1907, these tools had not been developed to one-fourth the capacity and refinement which they have at present. At that time it was frequently stated that such a small tool, drilling holes of less diameter than the reciprocating rock drill, could not drill enough holes in a shift to permit the placing of sufficient explosive to break a tonnage of ore comparable with that produced by the "rock drills;" that the placing of small holes inclined upward, at angles steeper than 40' above the horizontal, could not be expected to produce results equal to the large flat, wet or dry, holes in the breasted back of an overhand stope, and would only shatter the ground so as to make the back unsafe. In spite of these adverse opinions, the hammer drills first showed their superiority over both heavy and light reciprocating drills in raising and in stoping, and then in drifting and quarry work. As a result, all of the reciprocating drills at the Franklin mines were scrapped three years ago, all of the mining work being accomplished with increased efficiency, as shown in detail in this article. With the advent of the hammer drill in this property, it was considered advisable to make comparative tests of all the tools accessible, and it has since been the policy to investigate the merits of any advance of the drilling art in order to get the maximum amount of work from the tools. The necessity of devising some means of standardizing drill tests, and of measuring the consumption of compressed air as well as the drilling speed, was early realized. The common test was to fill a measured air receiver with compressed air at a certain gauge pressure, run the drill until the pressure had dropped to too low a figure, then compute from the time, drop in pressure, and

Jan 1, 1915

By Nicholas Kowall, K. L. Clark

Maximum furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. Work oF Other Investigators In I938, Burns, Moore and Archer published & curve? that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the rallge found in construc-tional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only o.2o per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E 43xx steels, His procedure consisted of chill-casting a test bar that was large enough to give a a that could be prepared for Brinell indentations. The test piece was quenched immediately after solidi fication was complete and hardness readings were taken, so that the carbon content could he read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. Experimental Work Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By K. L. Clark, Nicholas Kowall

Maximum furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. Work oF Other Investigators In I938, Burns, Moore and Archer published & curve? that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the rallge found in construc-tional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only o.2o per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E 43xx steels, His procedure consisted of chill-casting a test bar that was large enough to give a a that could be prepared for Brinell indentations. The test piece was quenched immediately after solidi fication was complete and hardness readings were taken, so that the carbon content could he read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. Experimental Work Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By William P. Blake

The occurrence of the manganiferous variety of wolframite at a new locality in Arizona was announced in the month of May last." It occurs in the granite hills of the Dragoon mountains, in Cochise county, about 6 miles north of Dragoon Summit station, on the Southern Pacific Railway of Arizona. It is found in veins of white quartz, traversing a coarsely crystalline granitic gneiss, and, so far as yet determined, is without association with other metallic minerals in the same veins, except small quantities of scheelite. It is a very pure form of the mineral, and contains but little iron, the base being manganese oxide. The color is brownish-red; it is nearly the same as the color of the mineral originally described by E. Riotte from Mammoth District, Nevada.† Thin films or plates on the broad cleavage-surfaces, and thin cleavage-flakes, seen by transmitted light, are ruby-red, or rather more like the color of red zinc oxide or the mineral known as clintonite. By long-continued weathering the surface becomes less deeply colored, and assumes a bronze-like luster, like the dull oxidized surface of

Jan 1, 1899

By Norman C. Stines

Russia's mineral potential is a secret that has been effectively kept by the Iron Curtain. There is no conclusive data and because of its extreme importance to the Free World, the subject is greatly discussed. Opinions range from those presented by Paul Tyler in his article "Russia's Mineral Potential," June issue of MINING ENGINEERING to those of Norman C. Stines, presented herewith. Mr. Stines is a consulting mining engineer of Los Gatos, Calif. He was in Russia, China, and Manchuria from 1909 to 1918 as a mining executive. From 1917 to 1919 he served as assistant military attache Intelligence Branch U. S. Army in Petrograd, Russia.

Jan 11, 1951

By F. L. Wolf, G. E. Alderson

The reclaiming of nietallics from slag and sweepings is of vital interest to every brass-foundry man, but the first cost and interest on the investment often make it prohibitive for the small foundry to enjoy the benefits of a complete concentrating unit. However, the cost of such an installation and the cost of operation are often exaggerated to such an extent that foundries dispose of their copper-bearing refuse at a great loss. This paper gives the actual costs and the returns obtained in the reclaiming plant used at the Ohio Brass Co. This plant is divided into two sections—the preliminary treatment and concentrating departments. In the former occur the screening, crushing, and hand-picking operations whereby rnost of the non-valuable and heavy metallic constituents are removed. The concentrating equipment consists of an elevator, bins, jigs, ball-mill, arid table. Preliminary Treatment The preliminary treatment varies, depending on whether the material is slag, foundry-floor sweepings, or brass casting-floor sweepings. Material of the first class is produced from the operation of six Steele-Harvey and six Schwartz furnaces; the second class represents sweepings from an average of thirty-five. molding floors per day: and the last is collected around the sprue cutters and knockout bench. Treatment of Slag The slag, analyzing 30 to 40 per cent. copper, is passed over a 3-mesh yard screen (Tyler standard mesh) stretched on an inclined rectangular frame supported by adjustable legs and equipped with a hopper which directs the undersize into a barrow. The fine product, running about 20 per cent. copper and representing 20 to 25 per cent. of the total slag, goes direct to a storage bin for concentrator frrd. The oversize is charged into a No. 2 Hill cinder crusher, which takes 175 to 200 11,. to a charge and crushes two charges per hour through 'a No. 4 riddle. It

Jan 1, 1921

W. H. BASSETT, * Waterbury, Conn.-Manganese should not be expected to remedy all the defects that are due to poor melting practice. It is undoubtedly valuable in helping to eliminate porosity in many of the alloys. In the copper-nickel alloys, its use is becoming almost universal, for, beside helping to make sound castings, it tends to hold the carbon in solution in the solidified alloy. GWILLIAM H. CLAMER,? Philadelphia, Pa.-I have found that manganese copper is satisfactory for eliminating sulfur and that it works very well in the crucible and when you have reducing conditions; but in a large reverberatory charge, where the conditions are oxidizing, we were not able to eliminate the sulfur.

Jan 1, 1919

The papers that appear on pages 326 through 367 were presented at two joint meetings of the Mineral Industry Education Division, Geophysics Committee, the American Geophysical Union and the Committee on College Curricula of the American Association of Petroleum Geologists, at the A.I.M.E. meeting in New York on Feb. 17 and 18, 1941. At the first meeting, the Mining Geology Committee, the Society of Economic Geologists and the Committee on Applications of Geology of the ilmerican Association of Petroleum Geologists also took part.

Jan 1, 1946

The papers that appear on pages 326 through 367 were presented at two joint meetings of the Mineral Industry Education Division, Geophysics Committee, the American Geophysical Union and the Committee on College Curricula of the American Association of Petroleum Geologists, at the A.I.M.E. meeting in New York on Feb. 17 and 18, 1941. At the first meeting, the Mining Geology Committee, the Society of Economic Geologists and the Committee on Applications of Geology of the ilmerican Association of Petroleum Geologists also took part.

Jan 1, 1946

By S. Isserow

RECENTLY, a description of the wartime work in this laboratory on the U-Si phase diagram was published. This diagram was available earlier in the open literature; as were Zachariasen's crystal structure identifications for the compounds in the system. The uranium end of the phase diagram is shown in Fig. 1. The most recent work on this system has emphasized the peritectoid E phase, of particular interest for a number of reasons. The early work provided evidence of this phase's resistance to corrosion in water and of its slight ductility. Further information on these properties has been obtained here. Work elsewhere4 has provided evidence of stability under irradiation. This body-centered-tetragonal phase is relatively isotropic compared to the more usually applied a or ? uranium phases. Unlike the other compounds in this system, it contains no Si-Si covalent bonds.3 In addition, consideration on the basis of Pauling's concepts leads to the conclusion that in the E phase, uranium has a higher valence than in any of the other phases. Definition of the composition of the ? phase has been of prime concern in the study of this alloy. Evidence is presented below that its silicon content is slightly higher than that of stoichiometric U8Si, the composition frequently assigned this phase on the basis of Zachariasen's identification. This work on the composition required careful attention to the method of dissolving the alloy for analysis, since apparently low silicon contents could be found under certain conditions, see Appendix. Preparation: Melting, Casting, and Heat Treatment—Almost all the samples were from castings with a diameter of 13/4 or 2 in. and about 1 ft long, weighing 10 to 15 lb. The U-Si charge was melted by heating to about 1650°C in an induction heated vacuum furnace. Beryllia crucibles were used at first, but were replaced by zirconia-washed graphite as the technique of keeping the carbon content low enough (about 500 ppm) was mastered. The alloy was bottom-poured at about 1650°C into graphite molds. A few small buttons, weighing no more than 50 g, were prepared in a small arc melting unit.' Since cast material has a preponderance of uranium and U8Si2, heat treatment is necessary to ob-tain the ? phase by the solid-solid peritectoid reaetion. Once obtained, the ? phase is stable to room temperature, obviating the need for speeial attention to the method of cooling after epsilonization, see Fig. 1. It was found desirable to epsilonize at 800°C for a week. For some purposes, in which residual uranium and/or U8Si2 are tolerable, shorter periods may be adequate. The temperature of 800°C is not critical, since essentially the same results were obtained from 785° to 825°C. Further departure from this epsilonization range is inadvisable.

Jan 1, 1958

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

Binary alloys of titanium with silver, lead, tin, nickel, copper, beryllium, boron, silicon, chromium, molybdenum, manganese, vanadium, iron, and cobalt were studied. One-half-pound ingots of the alloys were prepared in an arc furnace, employing a water-cooled copper crucible, an argon atmosphere, and a water-cooled tungsten electrode. The half-pound ingots were fabricated by forging at 1700°F in air to 1/4-in. slab, followed by hot rolling at 1450°F to 0.060-in. sheet. Tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships were determined for these alloys. EARLY in 1947, as one phase of the evaluation of materials for Air Force Project RAND, Battelle successfully arc melted Bureau of Mines titanium and obtained a few basic properties of unalloyed titanium and several titanium-base alloys. The low density, excellent resistance to corrosion, and high tensile properties of these materials stimulated a great deal of interest among metallurgists and designers seeking better materials of construction. As a result of this early work, Battelle, under contract with the Air Materiel Command, Wright-Patterson Air Force Base, has continued extensive studies of titanium alloys. The result of the first year's work is described in three papers. The present one deals with binary alloys, the second with ternary alloys, and the third paper with quaternary alloys. Melting Method The arc furnace for melting titanium and other refractory metals was developed at Battelle Institute under Air Force Project RAND. During the present work, considerable improvement has been made in the design and operation of this furnace for making small ingots of titanium and titanium alloys. The improved furnace design is illustrated by fig. 1, which shows a cross-sectional view with the dimensions of various parts and their relationship to one another. The essential features of the furnace are the inert argon atmosphere, the water-cooled copper crucible, and the water-cooled tungsten elec- trode. The melting crucible is formed by spinning 0.064-in. annealed copper sheet. A groove for an O-ring seal is spun into the flange of the crucible. A fiber gasket between the crucible flange and the water-cooled brass cover provides electrical insulation. The brass cover is fitted with a sight glass, an opening for the water-cooled electrode, and a tube through which the material is charged. Direct current is used for melting, with the positive electrical terminal connected to the water jacket and the negative terminal to the electrode. A typical heat is made in the new furnace as follows: Approximately, 0.20 lb of titanium under 2 mesh per in. and the alloy addition, if any is to be used, are placed in the bottom of the crucible. The cover is clamped on the crucible so that the O-rings make a tight seal. The remainder of the charge is placed in a glass bottle, and this is connected by a rubber hose to the charging tube of the furnace. The crucible and the charge are evacuated with a mechanical pump to a pressure below 50 mm of mercury, or less if desired, and held at this reduced pressure for 5 min. Hot water is circulated through the jacket during the evacuation period to assist in outgassing the crucible. Following the evacuation, tank argon of 99.92+ pct purity is flushed through the crucible for 5 min and then adjusted to give a positive pressure of 1 to 2 psi. During subsequent operation, an argon pressure regulator introduces only enough argon to compensate for the small leakage which occurs through a mercury trap. Re-evacuation and reflushing the melting chamber with argon produced a negligible reduction in contamination. Two 550-amp generators, connected in parallel, constitute the power source. Normally, about 800 amp are used for melting alloys which are not extremely refractory. The generators are set for 90 v open circuit and 200 amp. The arc is struck and the electrode is withdrawn to produce an arc of 23 to 26 v. This voltage is maintained while the electrode tip is moved slowly around a circle 1 in. smaller than the diameter of the ingot. The current

Jan 1, 1951

By E. Cortese

Phosphate occurs in many places in Egypt, in two main zones: one in Upper Egypt, along the Nile Valley, principally on the right side, and one near the Red Sea coast. In the Nile zone, the principal layers of phosphate rock are to be found: in the mountains east of Mahamid (right side of the valley); in the hills near Sibaiya, also called Sebaieh (both sides); in the hills of Agula, Hagaza and Gurn (right side); and further on, along the camel road leading from Kena to Kosseir, a few miles east of Legheita's Oasis. Following that track, after having crossed the watershed, underlain by rocks like granite, serpentine, porphyry, and diabase, one comes again to the Cretaceous formation containing considerable quantities of phosphate, at Gebel Duwi, Gebel Nakheil, and Gebel Kosseir El Kadim, not far from the coast. More to the north, in the hills near Safaga Bay (Um El Uettat El Wasif) is another rich bed of the same formation. There are reports of phosphate existing near Suez and in the Sinai peninsula, and possibly some other zones can be traced or discovered in the future. The mines are well developed on the right bank of the Nile at Sharawna (near Sebaieh Station) and along the Red Sea coast, at Safaga and near Kosseir. Prospecting work has been done at Gebel Duwi, Gebel Gurn, Agula, Hagaza, and near Mahamid. The phosphatic formation in Egypt is quite variable, not only from place to place, but even within small areas. The phosphate is all of Cretaceous age, as is proved by the fossils found in it. It is considered to belong to the Campanian or, more appropriately, to the Maestrichtian series. The principal fossils are: Alectryonia Villei Coq. sp.; Roudereia Aures-sensis Coq. sp. = R. Drui Mun. Chalm.; Trigonoarca multidentata, Newton.; Cardita libyca, Zittel; Libycoceras Ismaely, Zittel; Nautilus sp.; Ancystrodon libycum Dam.; Corax pristodontus Ag.; Lamma biauriculata Zittel sp. Above the Maestrichtian beds, we have the Danian series, unconform-ably covered by Lower Eocene beds. Under the phosphate is a grayish marly clay, and beneath this, bluish-gray scaly shales resting on the Nubian sandstone (Santonian).

Jan 1, 1918

By Robert Isaac Williams

The Questa mine is located in northern New Mexico on the western flank of the Sangre de Cristo Mountains about 75 miles north of Santa Fe and ranges in elevation from 6,800 to 10,000 ft. GEOLOGY The rocks of the area are Precambrian metamorphic rocks covered by Tertiary extrusive andesites and rhyolites and intruded by Tertiary granitic rocks. These Tertiary intrusives are localized in an east-west belt about 20 miles long and 2 miles wide, extending from Questa to Red River. The Questa orebody is associated with a north-trending aplite intrusive about 3/4 mile wide and 1 3/4 miles long. In the area of mineralization, the metasomatism of aplite has produced a mottled porphyritic rock. This hybrid rock has caused much of the controversy about the Questa mine intrusive. The orebody is essentially monomineralic and consists of numerous closely spaced molybdenite veins varying in thickness from ' 'paint" to 3 in. and occurring in both the andesites and the intrusive. In the intrusive the veins are often siliceous. Common alteration minerals associated with the molybdenite ore vary with the original composition of the rock. The alteration of the aplite has produced phenocrysts of orthoclase, albite, oligoclase and biotite; veins of quartz, orthoclase, and biotite; and graphic myrmekitic intergrowths of feldspars and quartz. In many places near the contact, the andesite is indistinguishable from the metasomatized aplite. The dominant alteration in andesite, however, is the development of fine-grained biotite with apatite, rutile, and sphene.

Jan 1, 1969

By Carlton D. Hulin

ARE we a "have" or a "have-not" nation in our domestic supply of metals and minerals? Impinging on the ears of a people weary of war and faced with the problems of reconversion to peace, the import of this question has built up with the momentum of an avalanche. Stemming from statistics cited by Pehrson and accelerated by the pessimistic and possibly biased statements of Ickes, hardly an issue of any technical periodical dealing with mining has appeared during the past year but within whose pages was to be found some comment, some discussion of the question: Are we a "have" or a "have-not" nation? We have proved commercial reserves of high-grade iron ore in the Lake Superior region sufficient for 22 years, based upon the prewar rate of consumption; commercial copper reserves to last only 34 years, one fourth being inferred ore; zinc sufficient for nineteen years, over half being inferred; lead for twelve years, two thirds of which is inferred; mercury for only three years. So read the figures. Although admitting that these figures may be extended by new discoveries, by the use of marginal and submarginal ore, and by further technological advances, are we nevertheless to assume complete pessimism in the acceptance of the meaning of these statistics; are we to expect a rapidly increasing dependence upon foreign sources of mineral supply; are we to believe that we are at or near the peak of the "metal age" as has been held by Theodore J. Hoover? Or is some more optimistic viewpoint possible?

Jan 1, 1947

By H. S. McQueen

The insoluble-residue method for the examination and correlation of limestones and dolomites, or other sedimentary rocks containing calcium and magnesium carbonates, originated and was developed in the laboratory of the Missouri Geological Survey. The numerous and ever-increasing problems in the field of applied geology, and the need for a tool or aid in the solution of them, led to experimental work with samples collected from deep wells, in the early part of 1924. The success attained, almost at the outset, with this method was so great that the method has now been developed from the state of the experimental to the realm of large-scale, every-day routine. In a previous paper the writer1 described the procedure in detail and the characteristics of the residues obtained from certain Paleozoic formations in Missouri. The purpose of the present paper is to discuss the economic application of the insoluble-residue method. Developmental History Within the Ozark region of southern Missouri the geologic column consists of Lower Ordovician (Canadian of Ulrich) and Upper Cambrian formations, which are composed mainly of dolomite with subordinate amounts of sandstone, shale and limestone. Chert is found to some extent in all except one of the dolomite formations. The stratigraphy of the region is complex because the dolomites have lithologic similarities, fossils are few and often poorly preserved, and identifiable horizons within the comparatively thick formations are not common. Although considerable stratigraphic work of an areal nature had been done for a period of many years by the Missouri Geological Survey, the detailed geologic succession had not, until a few years ago, been systematically worked out. The problems of subsurface stratigraphy were even more complex. This region constitutes the main ground-water province of the State of Missouri and within it wells of varying depths are drilled in order to obtain supplies of ground water. In the work of the State Geological Survey in connection with the drilling of water wells for public supplies * Published with the permission of the Director, Missouri Geological Survey and Water Resources. Manuscript received at the office of the Institute Feb. 20, 1936. Assistant State Geologist of Missouri; Missouri Geological Survey, Rolla, Mo. References are at the end of the paper.

Jan 1, 1937