Search Documents

By Clark A. Sumner, D. Arthur Burnham

A process for recovery of greater than 99% of the copper contained in acid leach solutions by sulfide precipitation using hydrogen sulfide as a hydrometallurgical reagent has been developed. The process incorporates the concept of hydrogen sulfide addition to recycled copper sulfide solids in a turbulent flow area where further precipitation or agglomeration occurs to increase the effective particle size of the copper sulfide precipitate. Because the recycled solids provide a larger number of particles upon which momentary excesses of hydrogen sulfide are absorbed, oversulfidization of the product is prevented. Copper sulfide precipitates produced in this manner in a laboratory test reactor showed greatly improved physical characteristics compared to copper sulfide precipitates obtained by conventional direct precipitation in which H2S is bubbled directly into acid leach liquor. Copper sulfide precipitates were evaluated and compared by use of filtration tests and settling rate studies. Electron microscopic examination of the solids confirmed the presence of larger particles in reactor-precipitated copper sulfide. Flotation was examined as an alternative to filtration for recovery of CuS precipitates and was found to achieve complete CuS removal without addition of collector or frothing reagents in a period of 2 min. In the same test reactor, a rapidly floatable CuS precipitate was also formed by mixing H2S with acid liquors used to leach crushed copper oxide-copper sulfide ore (LPF process). In the presence of gangue from the crushed ore, flotation of both natural and reactor-produced copper sulfides resulted in recovery of better than 90% of the copper contained in the crushed ore.

Jan 1, 1974

By S. F. Frederick, G. F. Pittinato

The deformation mechanisms operating in Ti-5Al-2.5Sn at 20°K under uniaxial and biaxial stress fields were determined by using both optical and electron microscopy. In the uniaxially stressed specimens, de-fu~rnation twins were found only in the immediate vicinity of the fracture. Twinning was, however, established as a deformation mechanism under biaxial stress conditions. The same slip systems were opera-tiz,e under both uniaxial and biaxial stress. Prismatic slip was identified as the major slip syslem; however, basal and first-order pyramidal slip also occurred, but to a lesser degree. The interaction of moving dis-locations on intersecting slip planes resulted in the formation of jogs and dipoles. Hexagonal dislocation networks were formed only under biaxial stress conditions. A discussion is given on the formation of hexagonal dislocation networks. IT has been shown that titanium alloys can exhibit unusually high strengths when tested in a biaxial stress field.'-" The high biaxial strengths are a consequence of a strong basal plane sheet texture which results in distinctly anisotropic flow properties. This texture strengthening appears to decrease with decreasing temperature2 and would seem to indicate a change in deformation modes. For example, in a uniaxial tensile test, Ti-5A1-2.5Sn yields isotropically at 20°K but is strongly anisotropic at room temperature. The increase in biaxial ultimate over uniaxial strength at 20°K is also much less than at room temperature. It is known that titanium car] form deformation twins more readily at cryogenic temperatures than at room temperature.4 Since the formation of deformation twins will reduce the degree of basal texture in sheet material,' an accompanying decrease in texture strengthening would be expected. To investigate more fully the nature of texture strengthening at cryogenic temperatures, the deformation modes of Ti-5A1-2.5Sn tested in uniaxial and 1:1 biaxial tension at 20°K were studied by optical and electron transmission microscopy. EXPERIMENTAL PROCEDURE The uniaxial and biaxial stress test specimens were prepared from 0.020-in. thick sheets of Ti-5A1-2.5Sn ELI having the composition shown in Table I. Uniaxial stress conditions were obtained by using flat tensile specimens machined from the sheet material. The longitudinal axis of the tensile specimens was aligned perpendicular to the rolling direction of the sheet. Tile biaxial test specimens were prepared by rolling precut, 19-in.-lengths of sheet into 4-in.-diam cyl- inders. Following longitudinal butt welding, the cylinders were stress relieved at 1000°F for 4 hr. A 9-in. sq "window" was then chemically milled into each cylinder's surface reducing the wall thickness in the milled area to approximately 0.006 in. The testing procedure consisted of pressurizing the cylinders while simultaneously applying a tensile load. Using this technique, a 1:l axial to hoop stress was obtained. Complete details of the specimen and testing procedures are given in Refs. 1 and 2. The biaxial and uniaxial stress specimens were all tested in liquid hydrogen. Specimens for electron transmission microscopy were prepared by first chemically milling to a thickness of about 0.001 in. followed by electrolytic polishing to electron transmission thickness. The chemical milling solution, consisting of 800 ml of water,

Jan 1, 1970

By W. B. Phillips

The earliest mention of the sulphur deposits in what is now Culberson County, Texas, seems to be contained in " Explorations and Surveys for a Railroad Route from the Mississippi River to the Pacific Ocean, United States War Department, 1853-54." Captain John Pope (he was not commissioned Captain until 1856) had charge of one of the divisions of the Survey. In his report on the geology of the route, William P. Blake noted the analysis of a greenish earthy powder from the bed of Delaware Creek, at the springs, which contained 18.28 per cent. of free sulphur. The report states: "From the chemical examination of the waters of the spring, by Dr. Booth, it appears that chloride of sodium is the principal solid ingredient, but considerable quantities of sulphide of sodium are present. ***** The waters from the springs examined by Dr. Booth were alkaline, but it is possible that some of the springs are acid; and in this case the precipitation of sulphur would ensue on the mixture of the acid waters with those charged with alkaline sulphurets and the origin of the deposits of sulphur would be thus explained." This is the first reference to the existence of sulphur in that region, the first mention of the character of the water found there and the first suggestion as to the origin of the deposits. The possibility of the existence of acid waters was confirmed by E. M. Skeats, nearly 50 years later.' In this publication, Skeats says that the water from the sulphur deposits in Section 11, Block 114, Township 6, contains 79.08 grains of free sillphuric acid per gallon. This locality is about 13 miles (21 km.) south . of Delaware Creek and about 35 miles (56 km.) east of the Delaware Springs. The next published reference to the existence of sulphur in Trans-Pecos. Texas is in the Pirst Annual Report of the Geological Survey of Texas, 1889, page 226, where W. H. von Streeruwitz mentions that sulphur is found in that region, but gives no further information. In the

Jan 1, 1918

Mining as an industry of Utah had its inception in the activities of United States soldiers who came to the Salt Lake valley under the command of Gen. P. E. Connor, founder of Fort Douglas, in October, 1862. Many of these soldiers were from California and naturally employed their spare time in the search for minerals. Although their military status did not permit them to make locations in their own names, they assiduously prospected the region in accordance with their own knowledge and with in- formation conveyed to them by Indians and others. Their efforts were encouraged by their commander, who thereby fairly earned the title of father of the industry here, and by their other officers, and many discoveries that subsequently proved of great value were made by the soldiers. No systematic prospecting or mining had been done in the Territory previously although early Mormon settlers in the southern portion had mined a little ore from time to time in order to provide supplies of lead for bullets. The Mormon leaders at that time did not encourage mining. They held that agriculture was more important and profitable for their followers.

Jan 1, 1925

By James H. Pannell, John Dasher, Wilfred L. Freyberger, A. M. Gaudin

A new sorting process for beryllium minerals is described. This depends upon emission of neutrons upon irradiation by gamma rays, a nuclear reaction which is specific for beryllium at the appropriate energy level. Signals given by neutrons when ore passes on a belt are changed to mechanical commands through amplifiers and other electrical equipment.

Jan 4, 1950

By W. H. Emmons

INTRODUCTION THE deposition of metalliferous lode systems takes place at considerable depths and no one may observe the process. We see only the end results of the process and from these we seek to construct a theory that will account for them. Because there is an obvious relation between many lode systems and intrusive igneous masses, it is a natural inference that they have formed by fluids that were expelled from such masses. The metalliferous lode systems have been deposited by ascending thermal fluids that have risen mainly from great irregular bodies of intruding magmas which are called batholiths. Probably 95 per cent of such lode systems have formed in connection with acidic or "granitic" batholiths and probably less than 5 per cent have formed in connection with basic intrusives. The study of lode ores, therefore, should include the study of the intrusion and differentiation of the batholith. It was noted long ago1 that certain tin-bearing deposits are commonly associated with small stocks. That small stocks are cupolas of larger intrusive masses has generally been recognized. Butler,2 in his studies of the ore deposits of Utah, showed that the chief deposits in Utah are in and near the stocks; that is near the "apically truncated

Jan 1, 1933

By Bernard York, John J. Reed

W. 0. Philbrook (Carnegie Institute of Technology, Phila.)—Mr. DeVaney's paper is a valuable addition to the growing technology of the magnetic roasting of lean iron ores. His furnace is ingeniously designed to permit close control of the process and to achieve high thermal efficiency by counter-current heat exchange and the withdrawal of both solid and gaseous products at relatively low temperatures. The principle of using a lean reducing gas to avoid over-reduction of the ore even at high operating temperatures (for rapid reaction rate) is thoroughly sound. The gas analyses and flow rates reported, however, are internally incon- sistent and render suspect any details of a heat balance based upon them. While it is entirely proper to consider the entrant gas as a reagent and to account only for the heat evolved by consuming a portion of the gas, many operators are accustomed to a heat balance using the total calorific value of the reagent supplied; and comparison of heat balances made with different bases of calculation can be quite misleading. Since Mr. DeVaney's paper is likely to be cited frequently in future discussions of magnetic roasting processes, it seems worth while to point out the internal discrepancies and to give alternate values of heat requirements for different bases of calculation.

Jan 1, 1954

By Olav Klomstadlien

The lean, but extensive iron ore deposits of the Dunderland Valley north of Mo i Rana, Norway, are the raw material base for Rana Mines, a division of the state-owned A/S Norsk Jernverk steel mill. The iron bearing minerals are magnetite and specular hematite. The magnetite/hematite ratio varies considerably both within each deposit and from one deposit to another. The ore bodies that lend themselves to mining have generally a thickness of 30-60 m grading 30-35% Fe and 0.15-0.25% P. The grain size varies from 0.05 to 2.5 mm. The fine grained ores are hard while the coarse grained ores are soft and easy to grind. The A/S Norsk Jernverk steel mill operates both a sinter and a pellet plant, and this necessitates production of two types of concentrates. The present flowsheet is shown in [Fig. 1]. The crude ore from the pits is crushed in a 1.07-m gyratory crusher with an open side setting of 12.7 cm. The crusher product is transported by rail to the concentrator located 25 km from the mines. The ore is fed by twelve 1.22 X 1.83 m vibratory feeders onto conveyor belts which carry the ore to a surge bin ahead of the autogenous mills. The feed rate is automatically adjusted to maintain a set power load at a level suitable for the ore type being processed. The mills operate in closed circuit with twelve dual-drum screens equipped with a 0.8-mm screen cloth. Oversize is returned by gravity to the mill feed while undersize flows to the gravity separation section which consists of Humphrey spirals in three stages. The ores are very heterogenous and analysis may vary quite considerably. The quantitative need for concentrate in the steel mill may also change rapidly. The process in the concentrator must therefore be easily changed, and consequently alternative process lines have been established. This is indicated with the dotted lines in the flowsheet. Apatite is removed by flotation by fatty acids to give a final sinter concentrate of 63% Fe and 0.020% P or less. Pellet concentrate contains about 65% Fe and less than 0.020% P. The fineness is about 1500 Blain.

Jan 1, 1981

By R. O. Harma

Introduction Wet autogenous grinding is utilized in three iron ore concentrating plants operated by the Cleveland-Cliffs Iron Company (CCI). This paper will trace some of the development in converting from the use of metal grinding mill liners to the use of rubber and will update the current performance of rubber liners in these applications. The Cleveland-Cliffs Iron Company is a natural resources firm with major interests in iron ore mining and processing and oil and gas contract drilling. The company also has interests in oil shale, uranium, forest products, and Great Lakes shipping. The three operations discussed in this paper are the Empire and Tilden Mines on the Marquette Iron Range in Michigan's Upper Peninsula and the Sherman Mine in northern Ontario, Canada. The Empire Iron Mining Partnership is managed by The Cleveland-Cliffs Iron Company and is owned by Inland Steel, McLouth Steel, The Cleveland-Cliffs Iron Company, and International Harvester. The Tilden Iron Mining Partnership is also managed by The Cleveland-Cliffs Iron Company and is owned by Algoma Steel Corporation, Ltd., Jones & Laughlin Steel Corporation, The Cleveland-Cliffs Iron Company, Steel Company of Canada, Wheeling-Pittsburgh, and Sharon Steel Corporation. The Sherman Mine is a joint venture managed by Cliffs of Canada, Ltd. and owned by Dominion Foundries and Steel Company, Ltd. and Tetapaga Mining Company, a wholly owned subsidiary of The Cleveland-Cliffs Iron Company. The concentrators at all three mines utilize two stage autogenous grinding. Empire and Sherman process magnetic iron ores (Table 1) and utilize magnetic, hydraulic, and flotation concentration methods. Tilden processes an oxidized iron ore (martite, goethite, and hematite) and utilizes a selective-flocculation desliming and flotation concentration flowsheet. Final grind particle sizes are 90% -325M (43k) at Sherman, 90% -500M (25,u ) at Empire and 85% -500M (25 µ) at Tilden. Developmental History The success of using rubber mill linings in Scandinavia led to the first rubber mill lining used by CCI. It was installed in a conventional primary ball mill at Republic Mine in 1964 as reported by Lindroos (1970). This was followed by additional rubber liners for both primary and regrind ball mills. Generally these rubber linings provided about twice the service life as compared to the Type I Ni-hard liners previously used. Grinding efficiency of rubber was found to

Jan 1, 1982

By Amitava Gangulee, Michael B. Bever

The effects of changes in short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions have been investigated. The heats of formation at 273°K of several alloys after two different thermal treatments were measured by liquid metal solution calorimetry. Their electrical resistivities were measured at temperatures ranging from 4° to 773°k. Tensile tests and microhard-ness measurements were carried out at room temperature. An effective short-range order parameter and an effective interaction energy are defined. The measured changes in the properties are interpreted in terms of these quantities. The short-range order parameter is evaluated separately from calorimetric and X-ray data; the results are in fair agreement. Increasing short-range order lowers the resistivity of- the silver-rich Ag-Mg alloys but does not measurably affect the temperature dependence of the resistivity. Short-range order increases the yield stress of these alloys but does not affect the ultimate tensile stress. Changes in the effective short-range order parameter independently obtained from measured changes in the heat of formation, resistivity, and yield stress are in fair agreement. THE thermodynamic, electrical, and mechanical properties of solid solutions have been investigated as functions of composition in many alloy systems, but the effects of configurational variables, such as short-range or long-range order, on these properties have received much less attention. The silver-rich terminal solid solutions in the system Ag-Mg are well-suited for the investigation of the effects of order. The composition of these solid solutions may be varied over a range extending to about 27 at. pct Mg.1 Appreciable short-range ordering is likely to take place in these solid solutions; the degree of short-range order can be varied by suitable thermal treatments. In the alloy Ag3Mg long-range ordering is possible.2 This paper is primarily concerned with the effects of short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions.-The long-range ordering transition is the subject of a concurrent paper.3 1) EXPERIMENTAL PROCEDURES 1.1) Preparation of Specimens. Ag-Mg alloys containing up to 26.4 at. pct Mg were prepared by melting 99.99 pct pure Ag (obtained from Baker Chemical Co.) and 99.99 pct pure Mg (obtained from Eastman Chemi- cal Co. or Johnson Mathey & Co.) in graphite crucibles under molten potassium chloride. The solidified ingots were homogenized at 823°K for 10 days in evacuated Vycor capsules. A surface layer 6 in. thick was then removed by machining. The ingots were swaged into rods (2.5 mm diam) which were drawn into wires (1.0 mm diam). The wire specimens were annealed at 773°K for 24 hr in vacuum and either quenched into iced brine or cooled to room temperature over a period of 15 days. The average grain diameter (obtained from the linear intercepts) was about 0.1 mm. 1.2) Calorimetry. The heats of formation of the alloys were measured in a tin solution calorimeter as the difference in the heat effects of alternate additions of samples of an alloy and the mechanical mixture of its component elements. The additions were made from 273°K to the bath at about 623°K. The heat effect on addition of the alloys was approximately 5.5 kcal per g-atom. The procedure and the method of calculation have been described.4 1.3) X-Ray Diffraction. Short-range order parameters of two alloys were calculated from diffuse scattering intensities,' obtained with briquettes made from powdered specimens. A GE-XRD 5 diffractometer with filtered copper radiation was used. The absolute intensities were based on calibrations with paraffin. 1.4) Resistivity Measurements. The electrical resistivities were measured by a potentiometric method in which the potential drop across the specimen was compared with that across a standard resistance. For measurements below room temperature, the specimens were immersed in liquid helium (4°K), liquid nitrogen (78°K), dry ice and trichloroethylene (195°K), or ice and water (273°K). Measurements above room temperature were made on specimens held in a furnace under helium or in vacuum. The resistivity measurements were reproducible to ±0.5 pct or less. 1.5) Mechanical Tests. Tensile tests were carried out at room temperature with a Tinius-Olsen XY elec-tromatic Universal testing machine. Wire specimens (nominal gage length 1 in.) were used. The strain was measured with an extensometer, which had a sensitivity of 4 x 10-5; the strain rate was 10-3 min-1. Microhard-ness measurements were made with a square-pyramid indenter and a 100-g load.11 2) RESULTS AND DISCUSSION All measurements were made on two parallel sets of specimens, one quenched and the other slowly cooled from 773°K. The reported values are the averages of at least three measurements. In the range of magnesium concentration substantially below that of the composition Ag3Mg, quenched alloys have less short-range order than slowly cooled alloys. As the magnesium concentration approaches that of Ag3Mg, slow cooling develops long-range order. Quenching sup-

Jan 1, 1969

By H. H. Kaveler

Education is for the purpose of developing citizenship, and, if it is pursued for the additional purpose of preparing for a professional career, such as engineering, it is also directed to developing a knowledge of essential science, aptitude for the application of science to practical situations, and a knowledge of the industrial art in which the engineer will be engaged. The process of education required for engineering must of necessity extend beyond the classroom into industry. For that reason, the education of engineers should be divided as between the university and industry. Specialization in engineering should logically come as a result of experience in an industry. The student cannot take the time in a university, and, the university cannot teach the skills required to develop a specialist without sacrifice to the more essential broad purposes of formal education. In addition to talent in science, aptitude in the application of scientific fact, and knowledge of the industrial art, the engineer should possess certain personal qualities which are helpful in the pursuit of a professional career. Those personal qualities are: the ability to work as a partner in an enterprise, the ability to do jobs in a way whereby job performance is a means of gaining experience and increased responsibility, the capacity to write and speak in an understandable manner, and, a Proper regard for the "significance of answers." These pcrsOnal qualities may be of almost equal importance to acabemic accomplishments in the field of science. Development of such personal qualities are an essential part of the student's training in the university and in industry. They can be developed effectively through the leadership of instructors. Compulsory Education Nature played a mean trick On the human race when the evolutionary Process failed to develop in the individual a capacity to inherit knowledge. Were knowledge transmissible in a cumulative manner from generation to generation, mankind would be by inheritance wise beyond measure within a few generations. Then there would be little if any need for a "system of education." As matters stand, however, all must suffer the burden of starting life at the "zero " level of learning from which station each rises depending upon individual capacity to assimilate knowledge left of record by our predecessors and the individual effort exerted to compensate for Nature's failure to endow the offspring with intelligence. In the United States some degree of education is generally regarded as essential and necessary. Therefore, all citizens are subjected by law to an educational process covering the primary school age from six to sixteen years. Beyond the schooling required by law, many attend secondary schools, and beyond that, schools of higher learning. Our standard of living is at a level that permits an increasingly large fraction of the population the opportunity to go through all of the formal educational process. As a result, education in the colleges and universities has almost reached a mass production level. In spite of the high

Jan 1, 1949

By T. S. Taylor

THE development of the linear hot-wire anemometer has been chiefly clue to the efforts of L. V. Kings1 and A. E. Kennelly and H. S. Sanborn.2 The anemometers used by these investigators consisted essentially of a fine heating wire having attached leads for resistance measurements at distances of 10 or more centimeters from each other. In using such an anemometer, the current is measured that is necessary to maintain the resistance of the wire, between the two leads, constant for different air velocities. Thus resistance is always so chosen that the temperature of the heating wire will be sufficiently high to make the observations practically independent of small variations in the temperature of the gas in which the anemometer is placed. The measurement of the resistance of the anemometer wire requires a Kelvin bridge set up, which for commercial work is not altogether desirable. The cooling effect clue to different air velocities depends on the temperature difference between the wire and the gas and the total quantity or mass of gas passing the wire per unit tine. Since the temperature of the wire is maintained constant, the effect observed in the change in the heating currentfor a given change in air velocity is a measure of the difference between the gas flow in the two cases. Such an anemometer, therefore, measures the average gas flow for a length depending on the distance between the two resistance leads. Therefore the instrument in the form used thus far is not very satisfactory for measuring gas velocities in small tubes or in places where the velocity varies rapidly across the line of flow. For the purpose of measuring gas flow through relatively small tubes, where the velocity changes rather rapidly across the tube, the hot-wire anemometer has been modified in the manner shown diagrammatically in Fig. 1. It consists essentially of a platinum heating wire H about 0.007 in. (0.178 mm.) in diameter and ½ to 1 in. (12.7 to 25.4 mm.) long stretched across a suitable framework, say of glass. This wire has

Jan 9, 1919

By L. J. Erck, T. E. Ban

A discussion of laboratory procedures used to determine pellet quality and to simulate handling and firing conditions. Strength-temperature relationships in pelletizing; effect of chemical additives on agglomeration; and crushing, abrasion, and impact resistance of the pelletized products are discussed with respect to five different iron ore concentrates. IN most routine experimental work on products and processes, method:; of operation and product evaluation are established from accurately controlled laboratory tests. With particular emphasis on the pelletization of fine iron ore concentrates, standardized procedures of laboratory production and product testing have been established at Cleveland-Cliffs Iron Co. Research Laboratory at Ishpeming, Mich. A program of this nature was used for investigating the agglomeration characteristics of various iron ore concentrates. The factors which control the process were studied and subsequently controlled for these investigations. Pelletizing as applied to iron ore agglomeration involves the preparation of spheroidal masses from a fine moist concentrate, followed by high-tempera-ture firing to produce a final product. The preparation of moist spherorids is generally designated as balling. This produces the so-called green pellets or balls. After, these have been fired they are called pellets. Balling is accomplished by rolling moist concentrates in a revolving drum until small spheroids form by a snow-balling action. These balls are then heated in a shaft furnace, or a modification of this device, to a temperature high enough to cause agglomeration within the individual balls while they descend countercurrent to hot oxidizing gases. By this process the lour strength balls are converted through various chemical and physical-chemical processes into hard pellets. With correct balling and firing, the pellets are strong, resist abrasive action and handling treatments, and provide a suitable blast furnace and open hearth feed. In 1950 Tigerschiold and Ilmoni developed a working hypothesis to explain the formation and stability of green pellets.' Their work was presented on the basis of geologists' discoveries concerning the soil-water system and C. V. Firth's early postulates of green pellet formation.' Fundamental reactions oc-curing within fired pellets have been described by Cooke and Ban, who showed the microstructure changes caused by different firing temperatures." All these investigators have provided scientific clarifications of agglomeration by the pelletizing process and have opened avenues for greater development. Mineral grain growth and ceramic bond formation are the two basic phenomena imparting coherency to particles within a fired pellet of iron ore. Each of these is established by the transfer of thermal energy to the mineral particles. Grain growth mechanisms are chiefly physical reactions wherein smaller particles consolidate into larger ones, with resulting decrease in surface energy conforming with the second law of thermodynamics. Ceramic bond formation is a chemical reaction usually between basic and acid metallic oxides of the gangue and ore minerals. CaO, MgO, A1203, and FeO of Fe3O4, react in varying proportions with SiO, or Fe2O3, to form a great series of compounds or amorphous solid solutions. These product bond iron mineral particles together by a bridging action or by direct reaction with the surfaces of the particles. The result of the grain growth-ceramic bond formations is a consolidated, coherent compact of gangue and iron minerals formerly held together by much weaker bonds of interstitial water and forces common to dry, unconsolidated particles.4 With respect to iron ore agglomeration, these high temperature bonding reactions have been described by Schwartz, who referred to the bonds in sinters," and by Cooke and Ban, who referred to the bonds in fired pellets." The extent of the bonding phenomena and the consequent strength of fired pellets is governed by

Jan 1, 1954

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, Cornell M. E., graduate, aged 31, married. Will soon complete 2 years' engagement in the Russian oil fields. Eight years' practical experience in drilling for and producing oil. Can speak Russian fluently and some French and German. Open for engagement. Interview after August 15, in the United States. No. 299. Member, graduate mining engineer. Married. Aged 38. For past 6 years, general superintendent of large silver mine in. Mexico. Desires connection with responsible mining company, preferably in the United States. Has had 15 years' experience in the United States and Mexico, including mine engineering, sampling, examinations,' milling and mine superintendence. No. 312. Metallurgist, 4 years' experience in electric furnace operation on steel, ferro-alloys and smelting of ores, both practical and research, desires position as metallurgist or superintendent. No. 314. Member, technical mining graduate. 5 years' experience in coal and metal mines and construction work. Married. Aged 27. Employed at present. Interview in Salt Lake City or Denver. No. 316.

Jan 10, 1916

NEW MEMBERS The following list comprises the names of those persons who became members during the period Dec. 10, 1916 to Dec. 31, 1916. BOWMAN, Joseph V., Chem., Andes Copper Mining Co., Chanaral, Chile, South America. CALDER, NORMAN L., Min. Geol., Cia. Minera y de Fomento, Watkins, Fomento Prov. de Santa Clara., Cuba. CONRADS, RALPH A., Met. Engr., Magna Plant, Utah Copper Co., Garfield, Utah. FARR, T. H. POWERS, JR. Asst. Assayer, Argonaut Mining Coy Jackson, Cal HAURY, PETER S., Min. Engr ...Alta Loma, Cal. HOULE, ARTHUR, Supt., Shattuck-Arizona Copper Co., Box 2009, Bisbee, Ariz. LEIB, VICTOR E?, Min. Engr 4204 Ave. D, Austin, Tex. LINDSLEY, THAYER, Min. Engr 82 Beaver St.,. New York, N. Y. POTTER, OCHA Supt., Superior Copper Co., Houghton, Mich. ROCCA, BERNARD T.; Engr., Bluebell Mine, Cons. Arizona Smelting Co., Mayer, Ariz. SAFFOLD, RAY P P.'0. Box 436, Douglas, Ariz. THOMS, JAMES EZRA, Asst. Chief, Milling, -Roasting, Acid Depts., Mineral Point Zinc. Co., Depue, Ill. TOMITA, HARUYOSHI, Met. Engr., Mitsubishi Co., Osaruzawa Mine, Akita-ken, Japan.

Jan 2, 1917

By S. M. Purdy

Under certain conditions of hot rolling and air cooling from the hot-rolling temperature, bars of a high carbon (0.40 pct C) chrome-nickel austen-itic alloy were found to show magnetism even though no ferrite or martensite could be detected by microscopic or X-yay methods. The appearance of magnetism in such alloys may come from chromium impoverishment of the austenite grains near the precipitated carbide particles. SPORADICALLY, hot-rolled bars of Silchrome 10, an exhaust valve steel, have been found to be magnetic. Because of the analysis of the alloy—0.40 pct C, 18 pct Cr, 8 pct Ni, 3 pct Si —magnetism is unexpected. Preliminary investigation showed neither martensite nor ferrite to be present; only austenite and Cr23C6. Since a literature search was fruitless, a brief study was made of the appearance of magnetism in this alloy. The only basic difference between the two heats is the nitrogen content. Permeability was measured using a Severn magnetic gauge. This instrument consists of a magnet mounted on a counterbalanced arm. A set of calibrated plugs is placed in contact with one pole of the magnet. The specimen is placed close to the other pole of the magnet. If the specimen pulls the magnet away from the plug, it has a permeability greater than that marked on the plug. This technique is swift and reproducible. Previous experience has shown that the permeabilities obtained corresponded to those obtained on a permeater with a field strength of 100 oe. Specimens from both heats were annealed at temperatures between 1700 and 2300°F. One set of specimens was water cooled and another furnace cooled. All the water-quenched specimens were non-magnetic; the furnace cooled ones were magnetic as shown in Table I with no difference being observed between the two heats. Microstructural examination of the specimens showed the expected increase in carbon solubility with increasing temperature. Carbide solution was complete at 2200°F. The specimens heated to 1900°F or below showed some carbide precipitation from the hot-rolled structure. A furnace cooled specimen from a given temperature showed less carbide out of solution than the water-quenched specimen from the next temperature below; e.g., the specimen furnace cooled from 2100°F showed less carbide out of solution than the water-quenched specimen from 2000" F. These studies indicated that the appearance of magnetism was not related to the quantity of carbon in or out of solution and it was related to precipitation at temperatures below 1700" F. A set of samples annealed and water-quenched from 2100° F was aged for 4 hr at temperatures between 1000" and 1600°F; all were non-magnetic. A second set of samples, similarly annealed, was aged 1 to 24 hr at 1200°F with the results shown in Table II. None of the latter set of specimens showed magnetism until they had been aged about 8 hr. Magnetism was quite strong after aging 24 hr. X-ray diffraction studies on several of the magnetic specimens showed that the austenite had a lattice parameter of 3.58A and that the carbide was Cr23C6. Several of these samples were electrolytically digested in 10 pct HCl in ethanol, with a current density of 0.1 amp per sq cm. None of the particles in the residue were magnetic. Accidentally, one cell was run at 1 amp per sq cm; e.g., magnetic particles were found in this residue. After careful separation, the magnetic particles were mounted on a quartz fiber and their diffraction pattern determined using a 5.73-in. Debye-Sherrer camera with CrK radiation. These particles showed a fcc structure with a lattice parameter of 3.57A. Prolonged exposure, up to 16 hr, produced no other lines on the film. The following facts seemed to be established at this time: 1) Austenite was the magnetic phase. 2) Neither ferrite nor martensite could be detected. 3) Magnetization could be produced by aging at 1200°F. One explanation of these data is that the carbide precipitation impoverishes the region immediately around the carbide particle of carbon and chromium and increases the proportion of nickel. All of these serve to increase the Curie temperature of the region around the carbide particle. If the composition change is enough, the Curie temperature will rise above room temperature. If the volume of the affected region is great enough, the magnetism will become detectable. At low aging temperatures, composition changes are great enough but the overall volume of impoverishment is quite small

Jan 1, 1962

By Clyde Ross

The Thunder Mountain mining district is in eastern Valley County, Idaho. It is of undefined extent but nearly all of the development is confined to the ridge between Monumental and Marble creeks in unsurveyed T. 19 N., R. 11 E. (Fig. 1.) The district is still remembered among the mining men of Idaho because of the ill-advised rush there in 1902, but available evidence indicates that optimism regard-ing the future development of the gold deposits of the district is warranted. The former disappointment arose from the fact that many who took part in the early rush hoped for bonanza deposits, whereas the district is characterized by large masses of low tenor. In 1926 the writer,, assisted by C. Y. Behre, 3r., incidental to other work in the region, devoted four days to the detailed examination of the then access-ible workings in the district. Tha major workings in the Sunnyside, Venable, Standard and H-Y mines, most of which were still in good shape, were examined., Surface exposures at the Dewey were studied, but the main workings there have long been caved. The time available did not permit more than a cursory examination of the surface at a distance from the mines. Sufficient data have been gathered, how-ever, from published and unpublished accounts, production records and mine maps so that the major features of this deposit, by far the most productive in the dis-trict, can be summarized. The kindness of Messrs. Dan McRae and R: A. Davis in making available information regarding the mines of the district, a rd of these men and others in recounting early history and their observations in now inaccessible workings, have aided materially in preparing the present paper. A brief summary of the salient characteristics of the district has already been published.1/ Cir-cumstances have contributed to delay in the publication of the full official report, which will contain mine maps and ?such other detailed data as could be ontained. In view of the present interest in gold deposits it seems desirable to present here a summary of results of the study.

Jan 1, 1933

By Frederick Laist

About six years ago the Anaconda Copper Mining Co. decided to investigate the possibility of extracting zinc from the ores of certain mines in the Butte district. These ores are of a complex character and contain so much iron and lead that the concentrate contains only 33 to 35 per cent. zinc. Investigations showed that while a high-grade concentrate could not be obtained by ordinary methods, such as tabling and magnetic treatment, a fair grade could be made by the Horwood process. In this method, the concentrate resulting from the flotation of all of the sulfides is given a light roast and this calcine is subjected to flotation in the presence of a large amount of sulfuric acid; the resulting concentrate contains most of the zinc and a residue contains most of the iron. The fact that the lead, copper, and silver are divided approximately equally between the zinc concentrate and the iron residue and the large consumption of acid, which ranged from 50 to 100 lb. (22 to 45 kg.) per ton of concentrates, were serious objections to this plan. The zinc recovery, moreover, was low, as a considerable percentage invariably accompanied the iron. While a profit might be made on the ores by the use of this process, it was thought that other and more promising methods might be devised. After carefully studying the field and doing some laboratory work on various processes that had been suggested, it was decided that the electrolysis of sulfate solutions was the most promising. We soon found, as have other investigators, that the only way to obtain a good zinc deposit is to have the electrolyte free from all metals more electronegative than zinc, such as copper, cadmium, lead, arsenic, antimony, etc. Arsenic and antimony are particularly injurious, causing very poor current efficiency and small yield per horsepower when present in amounts so small as almost to defy detection—1 mg. or less per liter. A pure zinc is soluble only with difficulty in sulfuric acid; an impure zinc dissolves very readily. Electrolytic zinc deposited from pure solutions is, of course, extremely pure and dissolves only about one-fiftieth

Jan 1, 1921

By G. G. Brown

Enthalpy-entropy diagrams are presented for natural gases of 0.6, 0.7, 0.8, 0.9, and 1.0 gravity over the pressure range of 5 to 10,000 Ib. per sq. in. and temperature range of 32º to 700°F. The charts indicate directly the work requirement and temperature rise for adiabatic compression or temperature change for free emansion of natural eases. Computation and Uses of Charts The Mollier diagram (Fig. 4), in which the enthalpy (heat content) is plotted against the entropy with lines of constant temperature, pressure,, and in some cases volume, has been found most convenient when dealing with the compression, expansion, and flow of fluids. In dealing with the flow of fluids, the sum of the increase in the enthalpy, AH, plus the increase in kinetic energy, AM —, plus the increase in potential energy, ?MZ, representing the total increase in energy of the fluid in flow, is equal to the sum of the heat q, and work added, —w, to the fluid while flowing between the entrance and exit of the flow system. AH + AM— + ?MZ = q-w [1] In cases where there is no significant change in potential energy or in kinetic energy (velocity), it follows that the increase in enthalpy is equal to the total energy supplied to the fluid. Under such conditions' the changes in the property of the fluid as it flows through a throttling valve, choke, or any other similar arrangement, may be read directly from the enthalpy-entropy diagram by following a horizolltal line between the known pressures' When compressing Or expanding a gas by means of a Or or engine in which no heat is added to or subtracted from the gas, but only work done, the changes in the properties of the gas may be determined along a vertical line of constant entropy between the entering and exit pressures. The power required for the compression of the gas may be readily determined by converting the increase in enthalpy into the desired units. The enthalpy-entropy diagram for natural gases is to the gas engineer what the steam diagram is to the steam-power engineer. For this reason it would be extremely convenient if a reasonably satisfactory enthalpy-entropy diagram could be prepared as a function of the gravity of the gas. A careful study of the known properties of natural gas indicate that this is possible. The effect of temperature upon the enthalpy at constant pressure is expressed as the "heat capacity" or "specific heat" of the gas. The best available data for natural and petroleum refinery gases indicates the relationship shown in Fig. I. From this it is clear that the specific heat of natural gases is a function only of the gas gravity and the temperature at atmospheric pressure. The effect of pressure on the enthalpy of natural gases is dependent upon the pressure-volume-temperature relationships,

Jan 1, 1945

By Lawrence Addicks

Discussion of the paper of LAWRENCE ADDICKS, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1471 to 1484. L. D. RICKETTS, New York, N. Y.--In the Southwest we have stored up millions of tons of tailings in which the copper exists partly as sulphide and partly in an oxidized condition. Mr. Addicks' first paper suggests a, likely process for the treatment of such material. His second paper 1 deals with the recovery of copper from clear solutions of notable strength, and such solutions may come from the sulphating roast or direct from the leaching of completely oxidized copper ores of which vast deposits are known to exist. What strikes me particularly about the latter paper is the keen perception shown and the clear manner in which the writer has attacked the fundamental principles of the process. He calls your attention to the fact that ferrous sulphate is necessary in the electrolyte and is an ideal depolarizer; that sulphurous acid must be, used to reduce the ferric sulphate produced and thus prevent re-solution of copper at the cathode; that mechanical agitation in the cell, in order to bring the ferrous sulphate in contact with the anode and the copper in contact with the cathode, is essential to efficient work; that lead anodes are

Jan 12, 1915