Search Documents

By M. C. Leverett

Knowledge of the theory underlying the behavior of mixtures of fluids in reservoir rocks is essential to the proper solution of certain types of problems in petroleum production, but is as yet incompletely developed. The object of this paper is to show the application of well established thermody-namic and physical principles to these problems, and thus to assist in the development of the basic theory. For convenience the problems to be considered here may be divided into two groups: 1. Static problems, involving only the static balance between capillary forces and those due to the difference in densities of the fluids; i.e., gravitational forces. 2. Dynamic problems, involving analysis of the motion oi mixtures of immiscible fluids in porous media under the influence of forces due to gravity, capillarity, and an impressed external pressure differential. Capillary Equilbrium in Sands Under this heading the static type of problem will be discussed and the results of experimental investigations on the capillary properties of unconsolidated sands will be presented. Although the discussion of this section is, in a sense, prefatory to the treatment of problems of mixture flow, the concepts developed here have considerable intrinsic importance apart from their ap-plication to flow problems. For, it is reason-able to postulate that the reservoir fluids are, owing to their long existence in undis- turbed mutual contact prior to exploitation, in substantial equilibrium. It follows that their distribution in the reservoir at the time of tapping should be entirely predictable from the theory of capillary equi librium, provided certain experimentally measurable properties of the reservoir rock are known. Knowledge of the distribution of the several fluids in the reservoir is, ol course, helpful in the estimation of reserves and in other problems. It is to be emphasized that throughout the discussion of capillary statics it is assumed that the fluids are in equilibrium from the capillary standpoint. Thus, water, where it is referred to as being in a reservoir, will be understood to be interstitial water, present at the time of drilling the reservoir, commonly termed "connate" water. The theory developed here is perfectly general for any porous solid, whether a carefully prepared unconsolidated sand or a natural sandstone from an oil reservoir. At present, however, only problems involving clean, unconsolidated sands can be made to yield numerical solutions, since only such sands have been adequately investigated experimentally. Experimental evaluation of the pertinent properties 01 natural reservoir rocks will permit the extension of the numerical treatment to problems involving these materials. We shall now consider in some detail the static equilibrium of fluid mixtures in porous solids: that is, the manner in which the reservoir fluids are distributed vertically whell the Forces due to capillarity are just balanccd by those due to gravitation.

Jan 1, 1941

For the third year in a row total value of the Nation's mineral production broke all previous records. A new peak of $20.4 billion was reached in 1964. So says the U. S. Bureau of Mines. The Bureau's preliminary estimate for 1964 is $800 million higher than the value reported for 1963, and $1.6 billion greater than the 1962 figure. The unprecedented demand for minerals, has stimulated development of new mines and expansion of processing capacity in many parts of the country.

Jan 2, 1965

By Fred H. Klaer

Water supplies dependent upon induced infiltration can be developed by vertical wells, by infiltration galleries, or by horizontal water collectors. Each method is described and the advantages of water obtained by induced infiltration with respect to cost, chemical quality, and temperature are shown by specific water supplies. THE subject of ground water in industry is assuming increasing importance as new processes and new industries are developed. Industrial specifications of chemical quality and temperature for process water and for cooling purposes are becoming more rigid, and water must now have many properties to meet these requirements. As ground water is usually more constant in quality and temperature, many industries are turning to ground-water supplies to satisfy their growing need. As many published articles have stated during the past several years, the ever increasing demands have caused shortages of water supply in many localities throughout the United States. Although such shortages are generally of a local nature, they have given rise to many attendant problems, such as increased pumping costs, salt water encroachment, and rising ground-water temperatures. One partial solution to the problems of overdevelopment of the ground-water reservoirs in many areas can be accomplished by developing ground-water supplies that are dependent upon induced infiltration and by planning the use of underground reservoirs. These reservoirs can be filled during periods of excess precipitation and stream flow and can be emptied during periods of drought, in a manner similar to the use of surface reservoirs. In this way water that otherwise would be wasted into the oceans is salvaged during periods of excess. The development of water supplies dependent on induced infiltration is a relatively new concept and should be defined. When a well is pumped, the water level around the well is lowered in the shape of an inverted cone or cone of depression. As pumping is continued, the cone of depression will continue to expand, horizontally and vertically, until the quantity of water crossing the perimeter of the cone plus the recharge within the area of the cone is equal to the quantity of water being pumped.

Jan 1, 1954

By Edward H. Robie

MANY engineers currently are working harder than usual, in part because of the demands being made upon them for increased production in the war effort, and in part because engineers are in short supply so that there is more to do for those who are available. In some instances the question has come up as to what additional payment, if any, should properly be made for overtime work, and to what extent is such payment legally permitted under the rules of the Salary Stabilization Board. Most engineers employed in an executive, administrative, or outside salesman capacity are not paid for overtime. They are paid for doing a job instead of for the hours they put in, and are free to do all the unpaid home work they feel they should do after dinner, as well as to do a bit of thinking and worrying during wakeful hours in bed. But engineers employed in a strictly professional capacity normally have standard office hours. Some employers pay for overtime and some don't. Their practice as it existed on Jan. 25, 1951 may be continued. In the absence of such practice at that time, the Salary Stabilization Board says that the engineer may now receive additional compensation up to his straight-time rate for an extended work week. No formal approval of the Board is required. "A professional engineer," in the mind of the Board, "is a person employed in a professional capacity, who, by reason of his special knowledge of the mathematical and physical sciences and the principles and methods of engineering analysis and design, acquired by professional education and practical experience, is qualified to practice engineering." Inducted Engineers A letter from a young man just inducted into the service and fearful that his engineering training is not going to be utilized reached us last week from Fort Riley, Kan. The AIME, cooperating with the other Founder Societies, is doing what it can, through the Engineering Manpower Commission, to see that engineers are not being wasted in the military establishment. So we passed this young man's letter along to T. A. Marshall Jr., executive secretary of that Commission. Mr. Marshall tells us that the normal procedure now being followed by the Army in handling Selective Service inductees is to have them first complete 16 weeks of basic training before assignment to specialized categories. During that time they are classified. If one has an engineering degree he should be classified as scientific and engineering personnel at the end of the basic training period. He should then be transferred to a technical detachment and assigned an MOS (Military Occupational Specialties) reflecting his education. If a young man is looking for a commission, it might be added that the current policy in the Army is to transfer to OCS (Officer Candidate School) applicants for commissions in the infantry only. The local unit commander can give information on this point, based upon the aptitude shown in tests. In view of the current shortage of engineers, it is believed that a young man should seriously consider remaining in enlisted status unless he can obtain a commission in a branch of the service that can make full use of his technical skills. His work may thus be more to his liking even if his uniform is not. New York or Atlantic City? In which place is it preferable to hold the annual meeting of a professional society like the AIME-New York or Atlantic City? That is, a winter meeting. The American Society of Mechanical Engineers has held its recent meetings at Atlantic City, with increasing attendance and satisfaction. The American Institute of Chemical Engineers chose Atlantic City for its recent December annual meeting. Only twice has the AIME ever met in this famous seashore resort: in 1898 and 1904. Chief advantages of going to Atlantic City over New York are that technical sessions are better attended, there being little else to do there in Winter; the cost to members is less, and hotel facilities are better adapted to a large meeting. As to cost, take a banquet, for instance. The Chalfonte-Haddon Hall, which caters especially to winter conventions, charges about $7 for a banquet dinner of standard quality. A similar dinner at the Statler in New York would cost about $8.50, and about $10.50 at the Waldorf-Astoria. (The charge for tickets is somewhat greater than this because of the cost of music, programs, flowers, and other incidentals.) Rooms, too, are somewhat less at Atlantic City, two in a room being accommodated for about $7 per day each, compared with $7 to $10 at a headquarters hotel in New York. On the other hand, AIME headquarters is put to some extra expense for staff travel, food and lodging, and members living in New York and environs are forced to pay a hotel bill. New York, of course, has more varied amusements to offer, plenty of big stores, and the glamour of a big city. The choice may be discussed at the forthcoming meeting in New York. In the meantime if any reader cares to express an opinion one way or the other we shall be glad to hear it. College Scholarships Most parents of children in the later stages of high school find it necessary to give some consideration to the cost of a college education. Although salaries have increased substantially it seems that the cost of the necessities of life, such as food, housing, and maintaining the family automobile, have gone up even more, so the problem of financing the children's education is as acute as ever. Many overlook the possibility of scholarships, or feel that only a student at or near the top of his class has a chance to get one. As a matter of fact, close to 150,000 scholarships and more than 15,000 fellowships, worth some $42,000,000, are available in 1200 American colleges and universities. Those who are interested should send 55¢ to the Superintendent of Documents, Government Printing Office, Washington 25, D. C. for a 248-page publication just issued by the U. S. Office of Education, entitled "Scholarships and Fellowships Available at Institutions of Higher Education."

Jan 1, 1952

By R. W. Shearman, F. Weston Starratt

A new center for mining and metallurgical research is developing at Sterling Forest, N. Y., under the auspices of Union Carbide Corp. Here is to be located the Union Carbide Nuclear and Ore Research Laboratories. In truth, history has repeated itself; the Sterling Forest area in the days of the Revolutionary War, and for many years thereafter, was the mining and metallurgical center of the US. For in these Ramapo hills along the New York-New Jersey border, iron ore was mined, pig lion was cast, and the weapons of war and the plowshares of peace were forged. Before embarking on an historical pilgrimage to yesteryear-a brief description of Sterling Forest. Located in Orange County, N. Y., near Tuxedo, immediately north of the New York-New Jersey State line, and just west of the Erie Railroad and the New York State Thruway, Sterling Forest is approximately 35 mi from New York City. Title was acquired in 1956 from the Harriman family by City Investing Co. Its President, Robert W. Dowling, has established himself as a city planner, having conceived such projects as Pittsburgh's Gateway Center and Philadelphia's Penn Center. A unique, self-contained community -is planned that will contain light industry and centers for research and engineering. Colonies of homes will be interspersed throughout the 20,000 acres of forest land, lakes, and rolling hills. Culture will not be neglected, for Sterling Forest will be the new home for the annual Empire State Music Festival The Sterling Forest Gardens, 125 acres of landscaped woodland and streams, will become the "world's largest permanent floral showplace" The Sterling Forest International Research Building was opened earlier this year, and designed to provide all facilities needed by small growth research companies. The first major company to acquire land to construct research buildings at Sterling Forest is Union Carbide. 1763 ... Discovery of iron ore In turning back the pages of history, a fascinating story can be told of special interest to the metallurgist, the mining engineer, and perhaps even the sociologist. For, where new communities are planned today, older communities had been born, matured, and died. In these hills had lived the. iron miners, the blacksmiths, the lumbermen, the masons, and the teamsters that had given America its start in heavy industry. This was the area where the forests were crisscrossed with many wood roads that brought logs to the charcoal pits, and iron ore to the furnaces. Men make history. Our story brings forth many names of men known as ironmasters, or as industrial leaders-Hasenclever, Faesch, Erskine, Townsend, Ryerson, Parrott, Cooper, Hewitt, Jay Cooke, and Harriman. The name Sterling is derived from a Scotch Lord, the Fifth Earl of Stirling (in its earlier spelling). Lord Stirling was one of seven Englishmen granted a patent of land in the Ramapo hills by Queen Anne in 1707, known as the Cheesecock Patent. He sent an agent, Cornelius Board, to America in 1730, with the express purpose of looking for copper deposits. While he found no copper in his travels up and down the Ramapo Valley, he did find iron ore in two localities: first, in the vicinity of what is now Ringwood, N. J.; second, five miles to the north. There he constructed a forge and furnace at the edge of a lake in 1736, naming the land Stirling Property, after his patron. In 1740, the Ogden family in Newark bought land from Board at Ringwood and began smelting of iron in 1741. The Ringwood story Soon, a genius in the person of Peter Hasenclever appeared on the scene. He was attracted by an advertisement in the New York Mercury for March 5, 1764, in which David Ogden of Newark offered

Jan 1, 1961

By R. D. Coleman, A. E. McIlhinney, C. E. Capes

tentially valuable. These losses will probably increase with the expansion of production and will require the development of effective disposal and utilization processes under pressure of the lack of adequate disposal areas, the enforcement of air and stream pollution laws, and the economic need to obtain the maximum yield of salable product.1 Fine Coal Treatment Processes Most coal cleaning methods depend upon the density difference between coal and its impurities to effect separation. These gravity concentration methods, however, are not practical for particles finer than about 100 mesh and cleaning methods dependent upon the differences in

Jan 1, 1971

By A. Vignes, J. P. Sabatier

A study of ternary diffusion at 1315°C in the Fe-Co-Ni system covering the entire ternary phase diagram has been carried out. Experimental values of the four interdiffusion coefficients DFeNico,DFeCoCo, DFeCoNi were computed at 33 points of the ternary diagram. The limiting values of these coefficients on the three sides of the ternary diizgram have also been determined. This set of data is presented as a contour map on the ternary isotherm for each of the four coefficients. Assuming that the Fe-Co-Ni system can be considered as ideal, the phenomenological coefficients Lk ij (with k = Fe) have been computed and the Onsager reciprocal relutions verified. It is shown that, in the Fe-Co-Ni system, the diffusion process can also be described by only two interdiffusion coefficients DFeFe and DCoNiFe, the second cross diffusion coefficient DCoFeNi being equal to zero and the second direct difusion coefficient being given by The values of the cross interdiffusion coefficients and of the Onsager coefficients are explained in terms of atomic mobilities of the three components with the help of a kinetic calculation due to Lane and Kirkaldy.8 It is shown that all the results are explained if the tracer difusion coefficients of the three components are such that DFe > DNi ~ DCo in complete agreement with experimental data on the three binary systems. DIFFUSION in a ternary alloy system is basically and significantly different from diffusion in binary alloys. In binary diffusion, there is just one independent composition variable and only one coefficient Dij is needed to describe the interdiffusion process. In ternary diffusion, we must allow for cross interaction between two independent species, and four interdiffusion coefficients are necessary to describe the transport process. Kirkaldy et al.1,2 have determined interdiffusion coefficients in the systems, Cu-Mn-A1 and Zn-Cu-Al. Guy and Leroy4 have reported intrinsic diffusion coefficients for the r phase at 1300°C of Co-Ni-Cr alloys as a function of composition using the analysis of Philibert and Guy.3 Interdiffusion coefficients were measured at three different compositions at 850°C in the single phase copper-rich corner of the Cu-Zn-Mn system by Dayananda and race.5 Zie-bold and Ogilvie6 have determined interdiffusion coefficients in the single-phase field of the Cu-Ag-Au system at 725°C. Preliminary results on diffusion at 1136°C in the system Fe-Co-Ni have been reported.7 In this study, data are reported on a more complete determination of interdiffusion coefficients in the Fe-Co-Ni system in the entire ternary at 1315°C. There is complete solid solubility with the fcc structures at 1315ºC, and this system can be considered as nearly ideal. This approximation allows the computation of the Onsager phenomenological coefficients. These values can then be used to test a kinetic calculation of the Onsager L coefficients in ternary substitutional solid solutions due to Lane and Kirkaldy.8

Jan 1, 1970

By Hertha R. Freche

The diffusion of magnesium and silicon from the core into the high-purity coating of Alclad sheet is important commercially, and led to the use of a duplex product for the study of diffusion by means of spectro-graphic analysis of successive layers. It has been found that in the duplex materials the diffusion of magncsium from an undersaturated aluminum-magnesium alloy into its high-purity aluminum coating is approximately of the same order of magnitude as the diffusion of silicon from a saturated aluminum-silicon alloy into its high-purity aluminum coating. However, if magnesium and silicon are both present in the alloy in the ratio of Mg2Si, they appear to diffuse in the approximate ratio of this compound. Finally, if the alloy contains silicon in excess of the amount required by magnesium silicide, the amount of diffused silicon in the high-purity aluminum coating will also be in excess. The interdiffusion of metals in the solid state is of both scientific and technical interest, because it is helpful in the study of the alloy structure and in the solution of problems pertaining to the strength and surface condition of the fabricated product. W. C. Roberts-Austenlt carried out the first quantitative determination of the coefficient of diffusion of gold into lead. This classical experiment was followed by a series of investigations on the diffusion of metals and nonmetals in iron and steel and in nonferrous metals and alloys. Recently the diffusion of copper in coated strong aluminum alloys was investigated by A. Burkhardt2. This appeared to be the first published investigation on the diffusion of metals into aluminum. The present investigation was the direct result of a technical question in connection with alloy fabrication and is a summary of some preliminary work pertaining to the diffusion of magnesium and silicon into aluminum. The results necessarily will be subject to some variations, since this is the first attempt to evaluate the coefficients of diffusion of magnesium and silicon into aluminum according to this method of procedure. This

Jan 1, 1936

By E. B. Thornhill

(San Francisco Meeting, September, 1915) IN this paper on the recovery of mercury as sulphide, from the residues from the amalgamation and cyanide treatment of high-grade ores and concentrates, I will not discuss the many reactions, chemical and other- Fig. 1. wise, that take place in the general process, but confine myself more particularly to the methods of recovering the mercury. I submit charts of two amalgamation-barrel charges, Figs. 1 and 2, which are self-explanatory. The flow sheet of the high-grade and the mercury extraction plants is shown in Fig. 3.

Jan 8, 1915

By David R. Mitchell, E. C. Carris

THE particular field of application of machines utilizing air currents as the primary separating medium is in the cleaning of fine sizes of bituminous coal. Approximately 18,000,000 tons of bituminous coal was cleaned by air machines in 1947, but such machines have not yet been applied in the cleaning of anthracite. This chapter is limited to a description of the processes in which the separation between coal and refuse depends mainly on a difference in specific gravity. Dry processes depending on differences in coefficient of friction, shape, or other property, are described in chapter 17. The possibility of using air for the separation of coal from refuse was recognized early by mining men and many attempts were made to develop commercial machines. Some of these early machines are described by Berrisford,1 Chapman and Mott,2 and Mitchell.3 Only two machines are extensively used today in the United States, the Stump air-flow jig and the American oscillating table. GENERAL CHARACTERISTICS OF AIR CLEANING MACHINES The principles of gravity concentration and the properties of air as a medium for separation were explained in chapter 9. It was pointed out that because of the low density of air a medium of sufficient density has to be built with the material itself. Hence there must be some device to impart to the bed the necessary mobility for proper classification. It was also noted that the compressibility of the air may cause "geysering" of the bed and disturbance of the hindered-settling classification if the correct balance of conditions is not maintained. Most devices use a vertical upward current of air through the bed of material. They differ by the method of imparting mobility to the bed and the method of removing the refuse. In general terms, the air machines can be divided into three types: 1. Pneumatic jigs where the air current is pulsated. 2. Pneumatic tables where the refuse is diverted from the direction of flow of the clean coal by a system of riffles fixed to the deck.

Jan 1, 1950

By John Conley

THE production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.1 The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require addi-tional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary. Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnston,2 Smyth and Adams,3 Ralston et al.,4 Furnas,5 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894° to 898° C. The dissociation of dolomite and magnesite, although studied by several investigators, 4,6,8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (1) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1939

By Cyril Wells, Robert F. Mehl

THE practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out 1,13 This importance ties chiefly, though by no means only, in the study of carburizing and in the study of reactions involved in the eutectoid inversion in steel The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in y-Fe and their mutual effects are measured with precision The present paper reports the results of meas¬urements of diffusion coefficients D of manganese in -y-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients [$] Data on the rate of diffusion of manganese in y-Fe have been reported by Fry2 and by Paschke and Hauttmann 3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq cm per sec at 960°, which will be shown to be incorrect by many orders of magnitude Paschke and Hauttmann gave a rough value of 9 6 X 10-8 sq cm per sec at 1400° Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon METHOD AND MATERIALS Method -The method employed is identical with that used earlier 5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded The diffusion anneals were performed in argon, except one (test 18) in which hydrogen was employed for purposes noted below The temperatures reported are accurate to about 3° and constant within I°C , the diffusion times are reported to the nearest half hour The specimens were furnace-cooled after the diffusion anneal at about 2° per min Layers, usually 0 004 in thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0 01 per cent Mn, the distances of these layers from the interface was measured to ±0 0002 in The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions e The D values calculated by these two methods do not differ appreciably 5 The Grube solution was used except in tests in which the effect of concentration upon D was greater than 50 per cent, in such cases the Matano method, which explicitly provides for the variation of D with concentration,1 is the more reliable In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer In 3 of the 30 tests, however, this is not justified, and the D values

Jan 1, 1941

By Kwang K. Koh, Nicholas C. Nahas, Richard C. Neavel

Sodium, a relatively abundant element in Illinois coal, is reported to cause fouling of utility boiler heat exchange surfaces. Distilled water extraction of 22 Illinois coal samples resulted in average removal of more than 50% of their included sodium. Chlorine was the dominant anion. Extraction rate conformed to Fick's law of diffusion. Extraction with hot water increased both the rate and maximum amount removed. A commercial-scale countercurrent staged process can be envisioned as technically feasible.

Jan 1, 1978

By E. H. Rennhack

Phase equilibria of the zinc-rich portion of the Zn-Fe-A1 system containing up to 20.0 wt pct Fe and Al have been investigated at 600°C (1112°F), 450°C (842°F), and room temperature by metallographic and X-ray diffraction techniques. The phase relationships were found to involve only those phases present in the three binary systems. THE presence of small quantities of aluminum (approx. 0.2 wt pct*) in zinc galvanizing baths is known to suppress the formation of Zn-Fe alloy layers within the coating.' As part of an extended investigation of this suppression effect and the alloy reactions involved, the zinc-rich corner of the Zn-Fe-A1 equilibrium system containing up to 20.0 pct Fe and Al was determined at 600°C (1112°F), 450° F (842° F), and room temperature. The present paper reports the findings of this study. The constitution of the Zn-Fe system has been reported by Raynor2 based mainly on the work of Schramm3-3 and Truesdale et a1.6 The solid solubility of iron in zinc is extremely small and lies between 0.0009 and 0.0028 pct in the range 150° to 400°C (302°to752°F). Within the temperature and composition range of interest, a eutectic reaction involving nearly pure zinc, liquid = Zn+FeZn13, is observed at about 419°C (786° F) and 0.018 pct Fe along with a peritectic reaction, FeZn7+ liquid e FeZn13, at 530°C (986° F) and 6.2 pct Fe. The latter reaction is sluggish due to the large proportipn of solid phase involved in the transformation. Halla et al.,7 identified the compound FeZn13 as monoclinic with a = 13.68, b = 7.63, c = 5.07, and B = 128°44'. The structure of FeZn7 was reported by Bablik, et al.,8 to be of hexagonal symmetry, belonging to either the C6v = C6/m mc or D46h = C6/mc space group. Divensions of the unit cell are a = 12.81A and c = 57.6a. The Zn-A1 diagram as composed by Raynor9 and later Gebhardt10 is characterized by a eutectic decomposition, liquid 382°C (720°F) and 95.0 pct Zn and a eutectoid decomposition, at 275° (527°F) and 78.0 pct Zn. The eutectoid reaction cannot be suppressed permanently by quenching. Above 275° (527° F), a and a' co-exist in a closed miscibility gap between 31.6 and 78.0 pct Zn. Both phases are fcc and have nearly the same lattice parameter. The maximum solubility of aluminum in zinc (B) is approximately 1.0 pct at the eutectic temperature. PROCEDURE Materials. The experimental alloys were prepared from both massive and powdered material. Cast alloys were composed from three zinc-base master alloys containing 8.0 pct Fe, 16.0 pct Fe, and 50.0 pct Al which were made from C.P. zinc, Armco iron, and

Jan 1, 1962

By Neil H. Bostick

A specialized electronic data system processes data taken from normal gologic maps and stratigraphic tables to yield predictions of uranium resource location for an area such as much of the United States. Strata underlying specific quadrangle cells of the earth are evaluated for uranium favorability on the basis of selected criteria of lithology, structure, and stratigraphy but not specific past production in the area. Stored data are computer processed to yield volume of likely host rock beneath each cell to a given depth and at a given favorobility level. Results are plotted by machine directly as maps. A specialized and simplified procedure for predicting approximate uranium resources has been devised at Stanford Research Institute (SRI). The prediction is based on general geology beneath specific area cells of the earth in order to provide complete volume coverage; the strata underlying these areas are evaluated for uranium mineral favorability on the basis of a few selected geologic criteria in order to allow rapid data input. In order that the predictions be generally applicable, they are based on geological factors only, not past ore production of a given cell. Since the bulk of U.S. resources are in elastic host rocks, only such strata are considered in this work. This paper describes the structure and some details of the resource system and how it was tested in an area of the western United States.

Jan 1, 1971

By George Boulter

Draglines 8.2-1 Introduction. The nature and characteristics of rock and rock derivatives forming the crust of the earth vary so greatly from place to place that it is impossible to use the same numerical factors to show the, productive ability of excavating equipment on different jobs or projects. Factors for each project must be developed individually and applied as the conditions and requirements dictate. TYPES' OF DRAGLINES. Types of draglines are differentiated by the propelling method used and are generally divided into four classes, as follows: 1. Wagon mounted 3. Crawler mounted 2. Truck mounted 4. Walking Figure 8.2-1 shows a truck-mounted dragline. This type is considered to be the most mobile unit. In order to increase stability over the side, outriggers are installed as part of the truck chassis. This feature is not shown in .this figure. Figure 8.2-2 shows a crawler-mounted dragline. The long, wide crawlers are used to increase the stability and reduce the bearing pressure of this unit. These features allow for use of these units on surfaces too soft for the wagon- or truck-mounted types. Figure 8.2-3 shows a walking-type dragline. The large diameter tub and the well-supported boom through the gantry gives high stability for rugged works over a long life. BASIC PARTS OF A DRAGLINE. The basic parts of a dragline are illustrated in Fig. 8.2-4. A deck layout is shown in Fig. 8.2-5 with the main components named. OPERATION OF A DRAGLINE. Following is a description of the steps and controls present in a typical cycle of operation of a large dragline having independent hoist and drag motors. Starting the cycle with positioning the bucket on the ground under the point of the boom, the next step is

Jan 1, 1968

By Ellis Clark

THE mining town of Pribram is situated in Central Bohemia, on the western slope of the Heiliger Berg, 30 miles southwest from Prague. Birkenberg, the village in which most of the shafts and ore-dressing establishments are situated, is built on a mountain of the same name. It is about a mile from Pribram, is 1700 feet above the sea, and is surrounded by graywacke rocks of Silurian origin, which are intersected by greenstone dikes, and in the southerly, southeasterly, and southwesterly direction are bounded by granite. The graywacke formations consist on one side of graywacke sandstone and quartzite, and on the other of graywacke slates. These last are separated from the first in the immediate vicinity of the mines by a graywacke seam converted into clay. For many years this so-cal led clay seam (lettenkkluft) was considered as a boundary of the ore deposits in both zones of graywacke. The graywacke formation is divided according to its hardness, structure, texture, and color, into fine, coarse, compact, slaty, whitish-gray, reddish-gray, and black graywacke. The, miner divides the formation into four divisions. The first or lowest division, which is in contact with the granite, consists of a fine-grained dirty gray slate; the -second is a very fine to a very coarse schist, white to reddish-gray in color, and rich in quartz, but containing little mica; the third consists of a slate with a contused cleavage, which has a dirty gray, dark gray, and very often black color and is often graphitic in its composition ; the fourth consists of a fine to coarse-grained graywacke schist, of a grayish-white or reddish-gray color, and rich in quartz. The cleavage in all four divisions strikes from northeast to southwest, and the dip is sometimes northwesterly, sometimes southerly, and often vertical. All four zones are cut through by a great number of diorite and greenstone dikes and chimneys. The thickness of these dikes, which are of

Jan 1, 1881

By E. S. Machlin, Morris Cohen

The isothermal formation of martensite in a 71 pct Fe, 29 pct Ni alloy is found to take place mainly by the nucleation of new plates rather than by the growth of existing ones, and is dependent on the temperature and time of the isothermal hold, the amount of atherrnal martensite present, the state of internal strain, and the application of tensile stress. The conclusion is reached that the isothermal nucleation is activated by thermal fluctuations superimposed on localized regions of very high strain. The reaction-path concept, involving martensite nucleation at strain embryos by athermal activation on cooling, or by thermal fluctuations on holding, reconciles the athermal and isothermal modes of transformation, and offers a unified picture of the kinetics of martensite formation. THE phenomenon of isothermal martensite formation has been the subject of considerable study lately,'-' and its reality has been thoroughly established. The existence of such isothermal transformation has been claimed to confirm the nucleation and growth hypothesis as applied to the martensitic reaction.1 " However, the isothermal formation of a martensitic phase is also compatible with the reaction-pathw escription of the transformation. The purpose of this investigation is to examine the isothermal mode of the martensitic reaction, both theoretically and experimentally, in order to test the likelihood of the above two mechanisms. Material and Methods The alloy used in this study contained about 71 pct Fe and 29 pct Ni. The complete analysis was 29.5 ± 0.2 pct Ni, 0.036 pct C, 0.02 pct N, 0.19 pct Mn, 0.09 pct Si, 0.008 pct P, and 0.006 pct S. The amount of isothermal transformation was determined by electrical resistance measurements using a Kelvin double bridge. The specimens were in the form of rods 1/16 in. diam x 4 in. long. Aus-tenitizing was performed at 1095°C for % hr either in a pre-purified nitrogen atmosphere or in an evacuated Vycor tube, followed by oil quenching to room temperature. After this treatment, the samples were completely austenitic, and the transformation studies were conducted at subatmospheric tempera- tures. Lineal analysis and X-ray determinations of retained austenite were used to calibrate the electrical resistance changes in terms of the percentage of martensite. The martensite range curve for this alloy is given in Fig. 9 of ref. 6. The M, temperature occurs at about -18°C (255°K). Reaction-Path Theory The nucleation and growth description of the martensitic transformation that occurs isothermally has already been given by Kurdjumow.','2 However, no comparable treatment exists using the reaction-path concept." Consequently this section presents the reaction-path description of the isothermal mode of the martensitic transformation. According to the latter theory, there is a reaction path (a strain) which describes the relative motion of the atoms during their transference from the austenitic to the martensitic state. The possibility exists, therefore, that the nucleation of a martensitic plate is accomplished by an embryo that comprises a state intermediate between that of austenite and martensite. This state may be attained within a finite volume by means of a homogeneous strain of the austenitic matrix. There is a free-energy barrier (F.) along the reaction path, corresponding to a critical strain in a critical volume. When activation is achieved, a spontaneous increase in strain and volume of the embryo takes place to generate the full-size martensitic plate. This mode of nucleation is to be distinguished from the more conventional mode involving embryos of the martensitic phase that merely grow in size by an interface motion. There are two ways whereby embryos in the austenitic phase can achieve the critical state of strain for isothermal nucleation: 1—through the formation of internal strains by plastic deformation or by stress; and 2—through thermal fluctuations, preferably superimposed upon existing internal strains. The activation free energy F,, must be supplied either mechanically by internal strains or thermally by energy fluctuations, or by a combination of both.

Jan 1, 1953

The object of crushing and grinding for leaching is obviously to permit contact of the solvent and mineral and subsequent removal of pregnant solution in a reasonable time. Heap leaching is the leaching of ores that have been mined and transported to prepared, relatively impervious pads for leaching by sprinkling or ponding, and percolation of the lixiviate through the ore. Dump leaching is the leaching of dumps or low-grade ore or overburden without the use of prepared pads under them. Run-of-mine material, e. g., low -grade ore from open pit stripping operations, may be leached without crushing, and a fairly high recovery made by heap leaching. An alternate method for better grade gold/silver ores is to crush to 9 to 13 mm (318 to112 in. ) size for pad heap leaching, as used by Smoky Valley Mining Company at Round Mountain, Nevada, on gold ore, and to 38 rnrn (1 -1 12 in.), which will be done by Candelaria Partners, at Candelaria, Nevada, on silver ore. Heap leaching of copper probably began at Rio Tinto, Spain, about the year 1752. This was done by the leaching of weathering piles of ore in the open air followed by iron cementation of the liquor that drained off the heaps. Its application to the low -grade southwestern United States copper ores was overlooked for many years, and low- grade ores from Sacramento Hill at Bisbee, Arizona, were the first to be heap leached in 1923. Site preparation used a half century ago is the same today. "The need for some form of waterproofing of the pad was evident. Before leaching ore was piled, the site was cleared of cactus and brush. After clearing a gentle sloping area, it was then covered with a blanket of rolled and tamped clay or slime tailing. When heaps are built, a layer of coarse fragments may be put down first to assist drainage. A second method of leaching without grinding, usually for higher grade ores, is by vat or tank leaching of material crushed to 9 to 13 mm (318 to 112 in.) size. Such a plant is considerably more expensive than a heap leaching installation but much less costly than grinding for agitation leaching, and a recovery higher than that obtained by heap leaching is to be expected. Vat leaching has been widely used by the copper industry on higher grade copper ores but has been used in only a few small operations on that size gold or silver ores. However, such a plant should be considered for a modest tonnage of a few million tons, 3 to 7 g per mt (0.10 to 0.20 oz per st), of Carlin-type leachable ores crushed to 9 mm (318 in.).

Jan 1, 1981

By Leon McCulloch

WHEN clean iron and metallic zinc dust, protected from the air, are heated below the melting point of zinc, the iron takes on a coating that has excellent protective value. This coating is a brittle alloy of zinc and iron, and the process is called sherardizing. Although the zinc particles are covered with oxide and cannot touch the iron, an extremely small amount of the zinc vaporizes and the vapor, reaching the iron, alloys with it. Other zinc then vaporizes to replace that which has been removed from the atmosphere. This process continues indefinitely at a decreasing rate, for the coating already formed permits zinc to diffuse through-it to combine with the iron beneath. In this way, the coating grows outward from the surface of the iron, as the bark grows from a tree. The method of growth was clearly seen while sherardizing small cubes of cast iron, at about 450° C., in a small glass-stoppered bottle enclosed in a rotating drum. The dust contained about 3 per cent. iron, which prevented caking, and coatings 1/2 in. thick were grown in a few hours. After a heavy layer had been formed, the cubes were again: treated for a shorter time. The layer last formed was seen to lie next to the iron, instead of at the outer surface, showing that the growth was from the surface of the iron outward. The coatings split at the edges and corners, leaving the iron exposed there. Flakes of graphite from the iron were lifted upward and embedded in the coatings. The composition of sherardized coatings varies from the outer surface inward, as would be expected from the mode of growth. That is, the iron content increases slowly at first, then more rapidly as the iron is approached. At the surface the least amount of iron possible is 6 per cent., as the experiments described below have shown.

Jan 2, 1922