Search Documents

By Frank C. Kelton

A method is outlined for the analysis of large cores, developed primarily for the purpose of obtaining reliable data on fractured or vugular limestones. Porosity and fluid saturations are determined by a modified Dean-Stark extraction after initially bringing the samples to 100 per cent liquid saturation by a vacuum-pressure method. Horizontal permeabilities on the whole samples are determined in two directions, parallel and perpendicular to the di-rection of principal fracturing. Results are presented for various types of formations. A comparison is made between data obtained by this special method and the method of conventional analysis, and discussion is given of the relative advantages and limitations of each. In view of this comparison a modified method for the analysis of fractured and vugular formations is proposed, which method retains the advantages of the previously outlined techniques but gives promise of speeding up the analysis. INTRODUCTION For many years the greater part of the production in the Permian Basin was from formations of Permian and Pennsylvanian age. While production from these formations is still the predominant production. deeper prospecting has brought to light older formations with oil productive characteristics. Attempts to core these deeper horizons were at first usually characterized by poor recovery. The old rule of thumb, "good core recovery — poor well" was originated and remained in effect until recently. With the advent of diamond coring and the increased efficiency in drilling and coring operations. the old adage has lost its significance. Formations of Devonian. Silurian and Ordo-vician ages were successfully cored with varying degrees of recovery. The cores thus obtained were surprising and in some case; disappointing. Good recovery from these formations led to speculation as to the feasibility of analysis and the meaning of data obtained from conventional analysis. Commercial laboratories were engaged to analyze these cores. and their results indicated that data obtained by conventional methods would be of little value. From visual inspection it was apparent that in many cases the effective porosity for storage of hydrocarbons. and permeability. were contained largely in fractures and solution cavities rather than in the primary crystalline structure of the formation. In other cases the solution cavities augmented the effective porosity of the primary crystalline structure, or fractures enhanced the permeabiilty of the latter so that the formation might respond favorably to acidization and become commercially productive. Since the spacing of the cavities and fractures was often comparable to the core diameter, it was evident that the entire core should he analyzed instead of small fragments. On the basis of these observations, commercial laboratories were requested to devise a system of analysis which would yield data of practical value. Pro- cedures have accordingly been developed which seem to meet this requirement, and to date nearly 12,000 large core samples have been analyzed. It is the purpose of this paper to describe the methods used, to present typical results for several fractured formations and to compare the data obtained by this special analysis with that obtained by conventional analysis. Certain modifications and alternative procedures are finally suggested to speed up the analysis. CORE ANALYSIS PROCEDURE Fluid Saturations and Porosity The core sample, in segments up to 15 in. in length. is marked, weighed and examined under ultra-violet light to determine the presence of oil saturation. If present, the approximate quantity of oil and its location on intercrystalline, fracture or vugular surfaces is noted. This information is carefully recorded. The degree of fracturing and/or vugular development is also noted. The sample is then placed in a pressure cell and the air evacuated with a high speed vacuum pump. This evacuation is continued only long enough to reduce the pressure to approximately the vapor pressure of water in order not to remove excessive amounts of water. Water is admitted to the cell and allowed to penetrate the sample under atmospheric pressure, filling the pore space initially occupied by air and replacing the small amount of water removed by evacuation. Pressure up to 200 psi is applied to force water into the smaller capillaries, and the sample is left sub-

Jan 1, 1950

By Alfred W. Gauger, George A. Burrell

The senior author of this paper, while in Colorado on other official business, made a trip to the Cripple Creek gold-mining district to get more data than are at present available regarding the composition of the gas that issues from the rock into the mines of the district. This was done at the suggestion of George S. Rice, Chief Mining Engineer of the Bureau of Mines. There are -many questions of interest and importance in connection with the ventilation of the mines in the Cripple Creek district, such as the menace to life and mining of a suffocating gas entering the mines from the rock, the danger due to powder smoke (from blasting operations), and danger of continued inhalation of rock dust by the miners. This report confines itself to the first problem, the gas from the rock, and principally to one phase of this question, the composition of the gas and its effects on men and lights. A more thorough study of this and other ventilation problems is planned. That the rock gas is a real menace is shown by the fact that miners (variously estimated from 25 to 50 by different persons interviewed) have been killed by it in the 25 years that mining has been vigorously carried on at Cripple Creek. Many men have had narrow escapes from death, some of them having been incapacitated for days. In addition, much loss of time results because at certain periods of the year or on certain days it is impossible to enter some workings. At a few mines, fans force air into the workings, thus supplementing the natural ventilation and much improving conditions, but the improvement is not entirely adequate at all times. Origin of the Gas Lindgren and Ransome1 think that the gas found in the rocks of the Cripple Creek mining district represents the last exhalations of the ex-

Jan 1, 1917

By John R. Low

A number of cases of low-temperature, intergranu2ar brittle fracture of metals containing small amounts of certain impurities, have now been identified. Some degree of understanding of this phenomenon exists for the simpler binary systems of a metal and a single impurity, but the profound effects of other impurities and alloying elements in modifying this type of behavior remain unexplained. Current research in this area is reviewed and some of the newer techniques of investigation which should make possible a more quantitative study of the structure and composition of grain boundaries in impure metals are described. To indicate the subject matter of this lecture, we may begin by reviewing the experimental observations concerning low-temperature intergranular brittleness in impure metals, particularly those examples in which the embrittlement appears to result from what has been called "equilibrium grain boundary segregation."' These are the systems in which it has been impossible, at least up to now, to detect the presence of any second phase film at the brittle interfaces. When second phase films are present they are usually readily detectable by fractographic methods, often appearing as epitaxial films in geometric or dendritic patterns. An example is shown in Fig. 1 for the case grain boundary carbides in a sensitized stainless steel which failed by intergranular brittle fracture at 78?k2 In contrast to this type of embrittlement there are numerous examples of low-temperature intergranular embrittlement in which the fractographs are essentially featureless, for example, that of an oxygen-embrittled iron shown in Fig. 2. The only second phase particles visible are the small, widely separated, round oxide particles typical of the bulk material. The fracture surface is extremely smooth and the fracture path appears to follow the intergranular interface without deviation. This type of fractograph also implies that crack propagation has occurred without plastic deformation at the crack tip, since localized slip or twinning ahead of the crack would be expected to distort the interface and be readily visible in the fractograph. Such indications are occasionally seen in these fractographs, but are not characteristic. A second example of this type of fractograph is shown in Fig. 3, which is from a temper-embrittled, carbon-free, Fe-Cr-Ni alloy containing Sb, broken at 1OO?C.3 The similarity to the oxygen embrittled iron case will be apparent. In the case of the temper embrittled Cr-Ni ferrite containing antimony, it is possible to remove the embrittlement by suitable thermal treatment. The grain boundaries may then be examined by thin film transmission in the electron microscope for the material in both the nonembrittled condition and in the embrittled condition. Two boundaries are shown in dark-field transmission in Fig. 4, one in the nonembrittled

Jan 1, 1970

By H. Kreye, E. Hornbogen

An increase in electrical resistivity during aging or after quenching from high temperatures is known in a large number of alloys. Plastic deformation of alloys in this condition leads to a decrease in resistivity. This anomaly has been called the K effect. This effect has been reported in Ni-A1 alloys by several authors.'-4 The nickel-rich solid solution y is in equilibrium with Ni,A1 (y') with CkAu structure. With this alloy it is therefore possible to produce a homogeneous solid solution as well as a coherent mixture of y and y. The changes in resistivity should be determined for these two conditions. In the present literature on the K effect no distinction is made between them, because of experimental difficulties to determine small coherent particles. In the present work transmission electron microscopy and image formation by (100) and (110) superlattice reflection of the y' phase was employed for a detailed determination of the temperature dependence of solubility of aluminum in nickel and the resulting microstructures with alloys up to 15 at. pct Al. The solubility line follows the equation indicating a smaller solubility than given in the literature at temperatures below 700°C. X-ray scattering was used to get evidence for short-range ordering in the homogeneous solid solutions.5 Parallel to the determination of the microstructure electrical resistivity was measured as a function of aging tempera- ture, time, and aluminum content, which led to the following results: 1) Resistivity increases slightly during aging of a homogeneous solid solution which was quenched from a high temperature as a consequence of short-range order, Fig. 1, curve c,. 2) Resistivity shows a maximum during aging of all alloys which are heterogeneous according to the phase diagram, but which were obtained as a supersaturated solid solution by quenching, Fig. 1, curve c,. The increase in resistivity is mainly due to coherent precipitation of y'. In Fig. 2 the effects due to short-range order pN and due to precipitation of particles APT are shown for an aging temperature of 450°C and different aluminum contents. 3) The increase in resistivity depends on the size !f the coherent particles. A critical diameter of 15 5A for the maximum was found for all alloys and aging treatments by extrapolating particle sizes determined by electron microscopy. 4) The maximum of resistivity of the heterogeneous conditions does not occur if particles, larger than the critical size, have formed already during quenching. 5) Plastic deformation destroys short-range order as well as small coherent particles. Therefore a decrease in resistivity is observed if the increase in resistivity caused originally by these phenomena is

Jan 1, 1967

By Eugene R. Rice

(Canal Zone Meeting, November, 1910.) THERE are many methods for determining the meridian, but all of those in common use involve at least two separate observations, one for latitude and one for azimuth. Such observations made upon a south star at any hour are open to the objection of possible inaccuracy due to ignorance of the absolute refraction, and also to slow change in the altitude of the star when near the meridian. The method of observing a circumpolar star at elongation, besides requiring a separate observation for latitude, is open to the serious objection that clouds may obscure the star at the critical moment. Moreover, a tedious wait for the star to come to elongation is sometimes necessary. Many of us can recall long, cold, weary vigils, waiting for Polaris to reach elongation. For observing a circumpolar star at any hour, not only the latitude, but also the true time, must be known. This it is practically impossible to obtain, except in regions reached by the telegraph, and usually then one has to know the longitude also, in order to reduce "standard time" to "local time." The results obtained by this method, when the star is at culmination, are not very good, unless the true local time is absolutely known. The methods of obtaining the meridian from the sun, by means of a solar attachment, or by direct observation, while good, are not absolute, by reason of refraction, change in declination of the sun, and small change in vertical angle, when the sun is near the meridian. For these two methods, latitude, time, and approximate longitude have to be known. In the method here described, only one observation is needed, and from it azimuth, latitude, and sidereal time are computed. In other words, one can observe a circumpolar star-Polaris

Nov 1, 1910

By F. P. Nichols, F. A. Renninger

At one time, mineral aggregates were considered physically and chemically inert substances whose junction was that of an inex-pensive, easily obtainable source of bulk. This philosophy applied regardless of the use to which the aggregate was put. Research approaches dealing only with such gross physical properties as hardness, toughness, impact resistance, etc., dominated the early growth years of the industry and influenced specifications to a large extent. The accelerated pace of highway construction, which began toward the end of the depression years, focused attention on the need for extensive aggregate research. The realization in the early 1940's that aggregates interacted chemically as well as physically with their environment provided the stimulus necessary to translate the drab, systematic aggregate technology of the early 20th century into the changing, dynamic, challenging field it is today. Current research problems are discussed in detail. These efforts being pursued by contract research organizations, universities, governmental agencies, and industry transcend many fields. The mineral aggregate industry is the world's largest mining and processing endeavor, yet it is graced with little of the romance or public awareness that accompanies mention of gold, silver, iron, copper, uranium, or aluminum mining efforts. Much of this reaction is undoubtedly due to the fact that the uses to which crushed stone and sand and gravel are normally put are not fully recognized or appreciated by the general public. Almost 2 billion tons of mineral aggregates are quarried or mined, processed, and sold yearly in the United States alone.= The largest uses to which this vast tonnage is subjected are as ingredients of portland-cement concrete, bituminous concrete, and dense-graded aggregate-base course mixtures in the highway and building construction fields, two industries closely related to the expenditure of public funds. It is for these uses, partially in justification for the expenditures of vast sums of public funds, that mineral aggregate research truly finds its emphasis. The research efforts expended relative to the highway and building construction uses to which mineral aggregates are subjected are those of primary concern to the industry. These efforts, while of direct consequence to the industry due to the volume market represented, are of interest as well to public agencies, universities, and contract research firms. All actively conduct research, exchange information, and make contributions to the overall knowledge relative to aggregate usage and limitations. The research efforts of the mineral aggregate industry is the subject to be discussed throughout this paper. It covers all aspects of highway and building design, construction, and technology. The effects of research pertaining to quarrying and mining methods, blasting and processing techniques, storage and handling facilities, and equipment employment and development have left their mark on the crushed stone and sand and gravel industries. Such specialized efforts have resulted in dramatically increased production rates which in turn have served to keep costs, and hence prices, down. Despite the many inflationary pressures over the years, the cost of a ton of aggregate today is little more than it was 25 or 30 years ago. Mention is made of these efforts simply to emphasize the diversity of research in the mineral aggregate field. The remainder of this paper focuses on the complexity of what might be termed "product knowledge" research.

Jan 1, 1971

By Reginald E. Hore

Since the discovery of silver at Cobalt, Ontario, in August, 1903, more than 100,000,000 oz. of silver have been produced by the mines in the Nipissing district, and there is reason to believe that at least as much more will be produced in the nex five years. The estimated value of the aggregate output o ore to the end of 1910 is $48,327,280. The ore yielded 93,977,833, oz. of silver and was mined at a net profit of abou $16,000,000. For 1910 the production was 30,558,825 oz., valued at $15,436,894, and yielding a profit of about $9,000.000. The details of the production of the Cobalt district for the years 1904 to 1909, inclusive, as reported by the Ontario Bureau of Mines, are given in Table I. The shipments from Cobalt are in the form of smelting-ore, concentrates from milling-ore, and bullion. The smelting-ore is largely high grade, averaging about 3,000 oz. per ton A smaller return is from what is called low-grade ore and which

Jan 1, 1912

By H. Cecil Spicer

THE results described in this article are based on field work conducted during the periods April-May, 1939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation was completed under a cooperative arrangement made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. EARLIER STUDIES Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friede1 and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly3 described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger5 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to B00 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining Co.

Jan 1, 1941

By O. B. Bucklen, P. G. Meikle

INTRODUCTION The trend in the coal industry for many years has been to make every- thing "bigger and faster." This also held true for loading and storage facilities. Where once a million ton per year mine was rare, three to five million ton per year mines are not uncommon today in the bituminous industry. This greatly increased production, made possible through mechanization, required greatly improved loading facilities just to get the coal away from the mine. Also, there is a trend toward combining production from more than one mine and cleaning it in a single preparation plant. In addition to increased loading capacity, this frequently necessitates raw coal storage and blending facilities. The development of the unit train with its attendant economics, more than any other factor, has contributed to the widespread construction of storage and high-speed loading facilities. In the export market, the construction of ever larger coal colliers has contributed to a need for faster and larger loading facilities. In this climate of rapidly changing technology, any written account is faced with the possibility of obsolescence before its appearance. Thus, this chapter seeks to define the common and current practice in coal loading and storage facilities with the full knowledge that this practice is an ever-moving target. FUNDAMENTALS OF COAL STORAGE Storage of coal is becoming an increasingly important part of coal handling systems at mines, particularly since the advent of the unit train concept in transportation. In order to take advantage of reduced transportation rates on trainload shipments of coal offered by unit train movement, operators have found that storage is an economic necessity. In unit train practice large predetermined quantities must be loaded in relatively short periods of time as opposed to conventional practice where coal is loaded at a speed dependent on the production capacity of the mine and/or the cleaning capacity of the preparation plant. Two surveys of storage practices at mines reveal several objectives for storage.1, 2 Raw and/or clean coal storage is generally practiced in order to accomplish one, or a combination, of the following objectives: 1. To improve plant efficiency by distributing plant feed over the entire operating time, or to allow a preparation rate different from the production rate. 2. To limit interruptions of supply, ie, allow mine and plant to function independently with delays in one not affecting the operation of the other.

Jan 1, 1968

By H. Cecil Spicer

THE results described in this article are based on field work conducted during the periods April-May, 1939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation was completed under a cooperative arrangement made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. EARLIER STUDIES Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friedel1 and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly3described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger5 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 8oo ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining Co.

Jan 1, 1941

By Charles Y. Clayton

The shank, to give good service, should not upset nor should it cause excessive wear on the various parts of the machine. To fulfill these requirements, the steel must have a certain hardness—that is, resistance to deformation. The hardness is expressed in conventional terms, as Brinell or scleroscope number. Before deciding on the hardness that is proper, several factors should be considered; the most important are: type of drill steel used (whether hollow or solid), length of steel, nature of ground, air pressure, and hardness of hammer or anvil block (usually 600 Brinell). These are not all, but they are the most cogent ones. Without doubt, it would be better to use a shank that is too soft than one that is too hard. Most satisfactory service will be obtained from shanks that are just hard enough to resist any tendency to upset. To express the proper hardness in terms of Brinell numbers would mean a great many tests over a long period of time, or a study of drill steels that are being used successfully in the various districts. To obtain some information along this line, the persons making this investigation requested, a number of companies to send to them drill shanks that had been given the usual treatment at that mine. The results of the hardness tests are given in Table 1. The hardness values given in Table 2 are those of shanks known to have been quenched in water and drawn. These results show that where water quenching and drawing are in vogue the hardness is rarely under 400 Brinell.

Jan 1, 1923

By Charles Y. Clayton

The shank, to give good service, should not upset nor should it cause excessive wear on the various parts of the machine. To fulfill these requirements, the steel must have a certain hardness—that is, resistance to deformation. The hardness is expressed in conventional terms, as Brinell or scleroscope number. Before deciding on the hardness that is proper, several factors should be considered; the most important are: type of drill steel used (whether hollow or solid), length of steel, nature of ground, air pressure, and hardness of hammer or anvil block (usually 600 Brinell). These are not all, but they are the most cogent ones. Without doubt, it would be better to use a shank that is too soft than one that is too hard. Most satisfactory service will be obtained from shanks that are just hard enough to resist any tendency to upset. To express the proper hardness in terms of Brinell numbers would mean a great many tests over a long period of time, or a study of drill steels that are being used successfully in the various districts. To obtain some information along this line, the persons making this investigation requested, a number of companies to send to them drill shanks that had been given the usual treatment at that mine. The results of the hardness tests are given in Table 1. The hardness values given in Table 2 are those of shanks known to have been quenched in water and drawn. These results show that where water quenching and drawing are in vogue the hardness is rarely under 400 Brinell.

Jan 1, 1923

By Ottey M. Bishop, William G. Peryam, Fred E. Johnson

THE Lepanto Consolidated Mining Company is the largest copper producer in the Philippines, and the only one that makes a concentrate valuable principally for its copper; also, it has the only productive copper mine situated at considerable distance from the sea, and is the only one in the islands operating its own smelter. The Lepanto mine is in the Municipal District of Mankayan, sub-province of Benguet, near the heart of the Mountain Province of Northern Luzon. It is 165 km. from its shipping point at San Fernando, Province of La Union, on the shore of the China Sea. Elevations at the property range from 3200 to 4500 ft. The climate is very mild; temperatures are seldom below 50° or above 80°F. Annual rainfall approaches 170 in. and is mainly confined to a rainy season lasting from May to October. The months from December to April, inclusive, are usually extremely dry. This climatic pecularity entails the problems of landslides on the roads during the rainy season and water shortage during the dry season. The Mountain Trail, an improved rocksurfaced toll road maintained by the Commonwealth Government, gives access to the property. The 105 km. over this road may be traveled in about 4 ½ hr. during the dry season. Very few sections of the road are straight for more than 100 meters, and about one third of it is a one-way road controlled by gates. All freight for the property is delivered by the Manila Railroad Company to Bauang, La Union, 45 km. west of Baguio and at sea level, where it is picked up by freight trucks and hauled via Baguio to Lepanto. Granulated matte is hauled in bulk from Lepanto in four-ton lots on freight trucks to the storage bins at San Fernando. Freight rates from Bauang to the property amount to [P]8.oo per ton, and from the property to San Fernando the rate is [P]16.00 per ton. The company pays the road toll, [P] 1.00 per truck, each way. THE CAMP The company maintains a modern camp, well separated from the mine and reduction plant. Comfortable and sanitary living quarters, water, and light, as well as free medical service are provided all employees. A hospital staffed by a doctor and two nurses takes care of all medical treatment. Considering recreational facilities of great importance, the company has provided two tennis courts, two basketball courts, and badminton courts for employees. Bowling alleys and a motion picture theater are operated by the company, the profits being expended for other recreational purposes. A moderate sized recreation hall serves for barrio dances, meetings,

Jan 1, 1942

By Theodor Zuschlag

Electrical prospecting is the art of exploring the structure of the subsoil in regard to conductivity variations and interpreting the results of such exploration as to their geological meaning. Electrical prospecting has been applied during the last few years with outstanding success, not only to prospecting1 for ore but also to structural studies.2 Both applications have proved helpful to the geologist, and the latter application especially promises to become of still greater importance in the future. The mapping of structures is the most important function of the oil geologist. Oil is lighter than water, therefore in water-bearing beds it will migrate upward until the migration is stopped by a bed impermeable to the oil. Geologic structures such as domes, anticlines, faults and terraces, offer good prospects in the search for oil accumulations and can be traced easily by electrical prospecting, provided they are composed of a series of sedimentary layers of which at least one possesses fair electrical conductivity and follows the general trend of the structure. Conditions for Successful Mapping The first condition, fair electrical conductivity, is met in almost any oil-bearing series, because generally the electrical resistance of a sedimentary bed is identical with the resistance of the more or less saline waters, filling partly or entirely the pores of the rocks.3 Briefly, the electrical resistivity of a bed can be expressed for all practical purposes by the product R X P, where R is the specific resistance of the waters in the rock pores and P a factor depending upon the percentage of water by volume in the rock. The specific resistance of any solution can be computed from the chemical analysis, being primarily a function of the

Jan 1, 1932

By T. D. Teimann, R. L. Stone

The rate of extraction of silica from certain Wisconsin and Minnesota taconites was investigated by autoclave digestion in sodium hydroxide solutions over the temperature range from 296° to 416°F. Rates obtained were from 7 to 254 g mol per cm2 per sec giving activation energies from 15,000 to 19.000 cal per mol. Activation energy was found to increase with increase of sodium hydroxide concentration. Digestion of different forms of quartz indicated the rate of extraction to be solely a function of surface area under similar conditions of digestion. The results of an experimental investigation on the caustic extraction of silica from certain Wisconsin and Minnesota taconites were presented in a recent publication.' It was shown that residual concentrates containing as much as 65% iron can be produced by this method. The occurrence of silica as a micro-crystalline variety of quartz with high specific surface area gave correspondingly high mean rates of extraction in solutions of sodium hydroxide. The present paper extends this previous work by presenting the results of a study of the specific rates of extraction of silica from these ores as related to temperature, sodium hydroxide concentration and variety of quartz. Calculated activation energies for the dissolution of silica are presented and some possible mechanisms are discussed. TACONITES The low-grade siliceous iron ores investigated included taconite from the Wisconsin Gogebic range and a semi-taconite2 from the Minnesota Mesabi range. These are adequately described in the former paper1 and by the U. S. Bureau of Mines. The principal iron minerals are hematite (Fe2O3) and goethite (Fe2O3 . H2O), while the gangue is essentially a microcrystalline variety of quartz. Minor amounts of other minerals are present. Typical analyses show the Wisconsin taconite to contain approximately 28% Fe and 54% SiO2 and the Minnesota semi-taconite 39% Fe and 39% SiO2. Analyses of the actual samples used are given in Table I. The taconite samples were prepared for digestion by reducing the original ore to minus 200 mesh in a Braun pulverizer. QUARTZ Three varieties of quartz were studied in the investigation: Ottawa sand, chert and chalcedony. The Ottawa sand was obtained from the Ottawa Silica Co. The chert and chalcedony came from Wards Natural Science Establishment. A minus 200 plus 400 mesh fraction of the Ottawa sand, used as a surface area standard, was repeatedly washed in hot concentrated hydrochloric acid followed by distilled water before autoclaving. The other two varieties were used directly after grinding through 200 mesh in a laboratory hammer mill. Analyses of these samples appear in Table 11. Microscopic examination of the silica samples by the oil immersion method showed that the Ottawa sand consisted of clean, uniform spheres of quartz with little deviation in size from a mean diameter of 82µ determined by a distribution count. The other two varieties consisted almost entirely of microcrystalline aggregates of quartz crystals; the aggregates ranged from 10 to 70µ. The individual crystals in the chert aggregates were estimated to be of the order of

Jan 1, 1964

By M. Muskat

A theory has been developed describing the behavior of wells and reservoirs producing by the action of bottom water drives. It is assumed that the pressures are maintained above the bubble point, and that the permeability to viscosity ratio of the water in the flooded zone is the same as for the oil in the oil-saturated pay. Accordingly, the treatment is based on the homogeneous fluid potential theory. The effect of the difference in density between the oil and water is neglected. .4fter deriving the proper potential distrihutions, the nature of the rise of the water-oil interface below the producing wells is calculated. The primary clean-oil-production phase is expressed in terms of the displacement efficiency, defined as the fraction of the pay flooded out by the rising water table at tlle time of first water entry. The variation of this displacement efficiency is calculated as a function of the well spacing, pay thickness, the ratio of the horizontal to vertical permeability, and the well penetration. The important parameter, other than the well penetration, is found to be the ratio of the well separation to the thickness of the oil pay multiplied by the square root of the ratio of vertical to horizontal permeability. It was found that the displacement efficiency continually decreases as this parameter increases, and for values of the latter >3.5, the efficiency varies inversely as the square of the parameter. It also increases with decreasing well penetration. Perhaps the most striking result of this phase of the analysis is the conclusion that in order to explain the delay in entry of water in wells producing by bottom water drives for periods longer than a few days normal production, with drawdowns large compared with the differential density head between the oil and water, it is necessary to assume that the vertical permeability is a very low fraction of the horizontal permeability. An analysis is also given of the production history after the water has broken through, on the assumption that the production mechanism and details of the flow distribution continue to be the same as during the phase of clean-oil production. As is to be expected, it is found that the water cut will increase at an accelerated rate as production proceeds. However, the initial differences between systems of different well penetrations or well spacings with respect to the total clean-oil production gradually decrease in terms of the variation of the water-oil ratio with cumulative production. In particular, by the time the water-oil ratio has reached values of the order of 5 or greater the cumulative recoveries will generally differ much less among various producing systems than their corresponding clean-oil recoveries. Introduction On the basis of elementary geological principles, one may classify effective water-drive fields in two groups. In the first, the entry of water into the oil-producing formation may be characterized as an edge-water encroachment. This term is used to suggest that the motion of the water proceeds largely in a direction parallel to the planes of stratification. This type of water intrusion occurs usually in thin producing zones and in strata lying along structural flanks of appreciable dip. In the second group—"bottom water-drive" fields—the water-oil interface lies in a plane of zero or slight inclination to the

Jan 1, 1947

By M. Muskat

A theory has been developed describing the behavior of wells and reservoirs producing by the action of bottom water drives. It is assumed that the pressures are maintained above the bubble point, and that the permeability to viscosity ratio of the water in the flooded zone is the same as for the oil in the oil-saturated pay. Accordingly, the treatment is based on the homogeneous fluid potential theory. The effect of the difference in density between the oil and water is neglected. .4fter deriving the proper potential distrihutions, the nature of the rise of the water-oil interface below the producing wells is calculated. The primary clean-oil-production phase is expressed in terms of the displacement efficiency, defined as the fraction of the pay flooded out by the rising water table at tlle time of first water entry. The variation of this displacement efficiency is calculated as a function of the well spacing, pay thickness, the ratio of the horizontal to vertical permeability, and the well penetration. The important parameter, other than the well penetration, is found to be the ratio of the well separation to the thickness of the oil pay multiplied by the square root of the ratio of vertical to horizontal permeability. It was found that the displacement efficiency continually decreases as this parameter increases, and for values of the latter >3.5, the efficiency varies inversely as the square of the parameter. It also increases with decreasing well penetration. Perhaps the most striking result of this phase of the analysis is the conclusion that in order to explain the delay in entry of water in wells producing by bottom water drives for periods longer than a few days normal production, with drawdowns large compared with the differential density head between the oil and water, it is necessary to assume that the vertical permeability is a very low fraction of the horizontal permeability. An analysis is also given of the production history after the water has broken through, on the assumption that the production mechanism and details of the flow distribution continue to be the same as during the phase of clean-oil production. As is to be expected, it is found that the water cut will increase at an accelerated rate as production proceeds. However, the initial differences between systems of different well penetrations or well spacings with respect to the total clean-oil production gradually decrease in terms of the variation of the water-oil ratio with cumulative production. In particular, by the time the water-oil ratio has reached values of the order of 5 or greater the cumulative recoveries will generally differ much less among various producing systems than their corresponding clean-oil recoveries. Introduction On the basis of elementary geological principles, one may classify effective water-drive fields in two groups. In the first, the entry of water into the oil-producing formation may be characterized as an edge-water encroachment. This term is used to suggest that the motion of the water proceeds largely in a direction parallel to the planes of stratification. This type of water intrusion occurs usually in thin producing zones and in strata lying along structural flanks of appreciable dip. In the second group—"bottom water-drive" fields—the water-oil interface lies in a plane of zero or slight inclination to the

Jan 1, 1947

By O. Hyvärinen

The treatment of anode slimes at Outokumpu Pori Copper Refinery comprises the following process stages: copper leaching by air oxidation, nickel removal by digesting slimes in concentrated sulphuric acid at 200 °C, and dissolving of the formed nickel sulphate into water, roasting of the slimes in controlled gas atmosphere at 600 °C for selenium removal, smelting of slimes in a Doré furnace, electrolytic refining of silver, sulphuric acid and aqua regia leaching of slimes from the silver cells followed by the reduction of gold and platinum metals. The paper discusses operational experiences and recent developments of the process.

Jan 1, 1984

By E. T. Turkdogan, L. J. Martonik, R. J. Fruehan

Electrochemical measuretnents of the solid oxide electrolyte galvanic cells CY-Cr2O3 I ZrO2 (CaO) 1 O (in Fe alloy) CY-Cr2O3 I Tho2 (Y2O3)I O en Fe alloy) have been made at 1600°C (2912°F) in order to test the Performance of such cells at liquid steel temperatures. The oxygen pvobe (cell) consists of a disk of ZrO2 (CaO) or Tho2 (Y2O3) electrolyte fused at one end of a silica tube filled with a mixture of Cr-Cr2O3 which is the reference electrode. Upon immersion in liquid steel, the electromotive force readings achieve a steady value within a few seconds, and remain steady for 30 win or more. The perforwzance of the probes has been tested using Fe-O, Fe-Si-O, Fe-Cr-O, Fe-V-O, and Fe-Al-O alloys; the oxygen contents of liquid steel derived from the measured electromotive forces are in satisfactory agreement with those determined by arulysis. Use of the probe in the deoxi-datiorz of steel, in laboratory experiments, is discussed. The results indicate that there is insignificant electronic conductivity in ZrO2(CuO) at oxygen activities down to those corresponding to 10 ppm in steel. At lower oxygen activities, probes tipped with ThOn (Y2O3) disks perform satisfactorily at oxygen activities down to 1 ppm O or less. THE key to the control of deoxidation of steel is a sensing device to measure rapidly the concentration of oxygen in liquid steel in the furnace, ladle or tun-dish at any desired stage of deoxidation. The analysis of the cast steel by the neutron-activation or vacuum-fusion method gives total oxygen as oxide and silicate inclusions. This analysis is important for guidance to steel cleanliness; however, such a postmortem is of little value in the control of deoxidation of liquid steel. At the General Meeting of the American Iron and Steel Institute in New York, 1968, Turkdogan and Fruehan' presented a paper on the preliminary results of the work done in this laboratory on rapid determination of oxygen in steel by an oxygen probe. Details of the work done in this laboratory leading to the development of a galvanic cell for the determination of oxygen in liquid steel, and the results of the tests made are given in this paper. It was through Wagner's contributions, since the early Thirties, to the physical chemistry of semiconductors in general that it ultimately became possible to construct galvanic cells for application at high temperatures. In 1957, Kiukkola and wagner2 successfully demonstrated the use of several solid electrolytes in measuring the free energies of several chemical reactions, in particular, the use of lime-stabilized zir-conia in high-temperature oxidation reactions. Starting 7 years later, a number of papers appeared in the technical literature3-' demonstrating possible applicability of galvanic cells for the determination of oxygen in liquid steel. In the earliest work, Japanese investigators3j4 experimented with various types of reference electrodes, e.g., graphite-saturated liquid iron at 1 atm CO or Ni-NiO mixtures; the results obtained, though promising, were not of sufficient accuracy. Except for the work of Baker and West,6 all other investigators5,7,8 showed that ZrO2(CaO) electrolyte could be used for this purpose. The main part of the galvanic cell used by Fischer and ~ckermann' and by schwerdtfeger7 (the latter work was done in this laboratory), consisted of a ZrO2(CaO) tube, -1 cm ID, closed at one end, with a platinum contact wire fixed mechanically inside the closed end. The tube was flushed with a gas of known oxygen partial pressure, e.g., air, CO-CO2 or H2-CO2 mixtures; gas along with the platinum lead wire served as the reference electrode. The oxygen contents derived from measured electromotive forces agreed reasonably well with the oxygen contents determined by vacuum-fusion analysis. It is evident from recent investigations that the electromotive force technique using a solid oxide electrolyte is fundamentally well suited for the determination of oxygen in liquid steel. However, it is equally clear that the cell arrangement of the type as commonly used is in need of considerable improvement, as it exhibits several shortcomings for industrial and even laboratory use. 1) Because of its size, the zirconia tube, though stabilized, has a poor resistance to thermal shock. 2) Fine pores and microcracks, which are invariably present in zirconia tubes, are detrimental to the satisfactory operation of the cell, particularly when gas reference electrodes are used. 3) Air or carbon dioxide reference electrodes give rise to high electromotive force readings; as a result, the determination of oxygen in steel becomes less accurate. For higher accuracy, the oxygen partial pressure of the reference electrode should be in the range similar to that of oxygen in steel. 4) Even in laboratory experiments, difficulties are experienced when flushing the tube with gases and maintaining the proper gas flow rate. Fischer and Ackermann,' who used air as the reference electrode, reported that when the flow rate was too low, furnace gases would leak into the electrolyte tube, therefore lowering the oxygen potential and measured electromotive force. The required flow rate in order to avoid leakage depended on the tightness of the electrolyte tube which varied with different tubes, thus making it difficult to predict in advance the required flow rate. However, if the flow rate is too high the inside wall of the electrolyte tube would be cooler than the wall

Jan 1, 1970

By H. M. Howe

§ 24. Introduction.—This paper discusses the chief existing data as to the temperature, in iron-carbon alloys, of Ae3, the upper limit of the transformation range when in equilibrium, as distinguished from Ac3, the temperature at which the end of the transformation is noted in heating up, and from Ar3, that at which its beginning is noted in cooling down. The former is in fact carried above Ae3 and the latter below Ae3 by lag. I touch incidentally on the influence of manganese on Ae3 (§ 29, p. 614). The sections, tables, and illustrations are numbered consecutively with those in the accompanying papers by Howe and Levy on Determination of the Position of Ae3 in Carbon-Iron Alloys, and by Burgess, Crowe, and Rawdon on Thermal and Microscopical Examination of Professor Howe's Standard Commercial Steels, to which the present paper forms a sequel. § 25. The contradictoriness of our present evidence is shown by grouping it together in Fig. 14. For instance, both Goerens and Meyer (Series 2) and Meuthen (Series 12) used practically stationary temperature, and thus reduced the influence of lag very greatly; yet Ae3 for 0.32 carbon steel according to the former investigators is 894", but according to Meuthen it is at or below 770°, a discrepancy of 124" or more. In view of our ability to measure these high temperatures within a few degrees, the existence of such a discrepancy is as unwelcome as it seems needless. I attack the thankless task of bringing some order out of this chaos. In Part 11. (§§ 29 to 39) I consider the chief causes of error. In Part III. (§§ 40 to 48) I apply certain corrections to some of the existing data, review those data, weight them, and calculate a prob-

Jan 1, 1914