Search Documents

Soon after the Rosebery concentrator commenced operations in 1936, an investigation was begun in an attempt to discover a substitute for cyanide in lead flotation. Cyanide is an excellent depressant for zinc and iron, but it also powerfully depresses the copper, silver and gold bearing minerals present in Rosebery ore, thus allowing them to pass through to the zinc concentrate or final residue where they are of little or no value.The investigation was not entirely successful, but it did indicate that sodium bisulphite or sodium sulphite could be used as a depressant for zinc without depressing the copper, silver and gold bearing minerals. The sulphites were, however, much inferior to cyanide as apyrite depressant.At about this time, I. W. Wark, using the captive bubble technique, had shown that, at the concentrations normally used, sodium aerofloat is not a promoter for pyrite or galena in alkaline solutions (see his book "Principles of Flotation", p. 188). Some preliminary tests on the production of a copper concentrate from Rosebery ore were therefore carried out using sodium sulphite as depressant and sodium aerofloat as promoter.The results of this work were promising but, since Rosebery ore usually carries only about 0·5% copper, there did not seem to be much incentive to carry the work further. With the outbreak of war, however, Australia became desperately short of copper and the relatively small amount in the ore. became of sufficient importance to...

Jan 1, 1952

By D Audeyev

The Cooljarloo North Mine has been shaped not only by operational and processing challenges, but by climatic and economic factors. This paper outlines some of these challenges and discusses how the operating strategy has been altered over time to mitigate the impacts.Since commissioning the wet concentrator in 1999, there have been many typical operational challenges to maximising valuable heavy mineral (VHM) recovery. These include: varying in pit feed grades, different slimes types and volumes, sizing extremes between VHM and trash minerals and decreased equipment reliability handling rocky ore. These issues were successfully mitigated by: in pit extraction strategies, upgrade of the de-sliming circuit, thickener modifications and flocculent changes, installing upgraded and additional spiral capacity, and various Feed Preparation Plant screening initiatives. Combined with the ingenuity, persistence and patience of the operating team, VHM recovery >95 per cent has been achieved.However, typical processing challenges have not been the only hurdles. Reduced rainfall and water availability has necessitated the strategic co-disposal of tailings and slime to increase the speed of water recovery: groundwater abstraction and water storage strategies have also been altered. With an observed reduction in the speed and magnitude of groundwater recharge, overburden backfill scheduling has become a priority mine planning function.Combined with the above challenges, the prevailing foreign exchange rate and mineral product prices have impacted profitability. At the height of the Global Financial Crisis in 2009, major changes to the operating strategy were made to maintain a viable dry mining operation in 2010. Working with the mining contractor the existing scraper and semi-fixed Feed Preparation Plant set up was replaced with a movable in pit dozer trap facility. The end result of changes to the mining method and primary screening was a ten per cent reduction in unit costs. This article will elaborate on some of the above mentioned challenges and successes achieved over the past ten years of operating the Cooljarloo North Mine.

Oct 5, 2011

By H Indirawati, R Ayres, A Nur Kasnanto, S Konopa

As a project moves through the mine life cycle, the quantity of data available increases and the understanding of the orebody matures. Incorporating new information quickly and efficiently in current 3D models, is essential for adding value across the life-of-mine value chain. At the Martabe Gold Mine, the resource development group manages 14 drill rigs on six resource projects, including three operating mines. The Martabe deposits are geologically complex and the volume of new information that becomes available each day is substantial. It is imperative that new geological and assay information is integrated into the 3D models as soon as possible, so that drill planning and targeting can be modified accordingly. Martabe uses Leapfrog<sup>®</sup> 3D software to update and interrogate the 3D models on a dynamic basis as data becomes available. This results in faster and more effective changes to drill planning and schedules. The impact of this is better drill productivity and cost savings due to optimal drill targeting, and availability of up-to-date models incorporating the most current data. CITATION: Konopa, S, Ayres, R, Nur Kasnanto, A and Indirawati, H, 2018. Optimised drill targeting using dynamic 3D modelling, Martabe Gold Mine, Indonesia, in Proceedings Complex Orebodies Conference 2018, pp 99–101 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By H Utama, R Heryadi

The demand for environmentally friendly commercial explosives has increased globally due to concerns regarding environmentally friendly mining activities. Ammonium nitrate fuel oil (ANFO) and bulk emulsion explosives (BEE) are two kinds of civil explosives primarily used in coal and mineral mining in Indonesia. Indonesia is one of the leading countries in coal and mineral mining production and export, with abundant resources; therefore, the consumption of civil explosives such as ANFO and BEE is enormous. The selection and evaluation of commercial explosives are mostly done on the commercial and technical side, and no assessment is made based on environmental aspects. This preliminary study evaluates the economic value and environmental burden of greenhouse gas emissions produced by ANFO and BEE and determines which type of explosives is more environmentally friendly. The combination of environmental and economic indicators, eco-efficiency (E/E), was selected to investigate BEE’s economic and environmental performance compared to ANFO. The life cycle of greenhouse gas emissions of BEE and AN was determined using previously available studies and simple calculations. The cost of the product or explosives was used to represent the economic value. The E/E results showed that environmental and economic sustainability could be enhanced using BEE.

Sep 1, 2024

By B Beale

Bow-tie analysis is a commonly used tool in the Major Hazard Facility sector to identify, display and control risks that have the potential to pose serious harm to personnel. It is a simple but powerful risk management tool that displays traditional risk assessment outputs as easily interpreted ‘bow-tie diagrams’. These are an effective and versatile communication format that can be applied to any type of risk (eg safety, environmental, assets etc) and as such show great benefit in managing operational hazards in mining.

May 5, 2022

By S Jeffrey, S Mundell, F Arboleda

In the current cycle of low commodity prices and rising costs, mine managers continue to focus on optimising mine performance and productivity. A critical component of strengthening performance and productivity is ensuring material is routed correctly and efficiently through the core mine production activities of drilling, blasting and grade control.By the time a blast is planned, an enormous amount of intellectual property has been invested in the exploration, resource development, feasibility studies and mine planning activities. The value of that knowledge is either realised or diminished during mine production. Efficient execution of the process is critical and is reflected by the quality and timeliness of the information produced.Multiple teams are involved in the mining extraction process. These teams are all under time pressure to keep the mine equipment operating. One of the root causes of this pressure is the dependency between the teams. They do not operate in isolation, but are a link in a chain depending on the outcomes of each activity. It is essential communication is efficient so tasks can be completed according to the production schedule. Unfortunately, communication fails when unintegrated systems are used because of:- different teams seeing different data, hence there is not an overall, up-to-date view of progress and priorities- lack of cross-functional visibility of data leading to failure to identify errors in time to address or correct issues- teams tending to be siloed and focusing on their part of the process rather than the overall objective.With different systems used for the parts of a common goal, supervisors and managers lack visibility of the process. This makes it difficult to identify process improvement opportunities.Streamlined communications help consolidate all data and activities resulting in improved cooperation between mine production teams. This outcome increases the confidence and efficiency of material routing decisions. It also reduces potential impact to mine performance from errors in early stage tasks like drilling and grade control. Having everyone collaborating off the same trusted data, helps teams identify with common goals and find business improvement opportunities as they appear.CITATION:Arboleda, F, Mundell, S and Jeffrey, S, 2016. Driving mine performance through communication, in Proceedings International Mine Management Conference, pp 117-124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Whang K, Choi H

A study of flocculation of ultra-fine coal particles by ultrasonic waves was investigated on a laboratory scale.The coal suspension was dilute, with low ionic strength, and at pH 6·2.When a stationary sonic wave is set up in a solution containing suspended coal particles, it is believed that high and low pressure regions are alternately established at the half wave-length of the sonic wave and this resultsin the migration of coal particles towards the low pressure regions.As expected the flocculation is more effective as to frequency and the power of the ultrasonic waves is increased.The shape and size of the test equipment are also important variables.

Jan 1, 1977

Engineering education has become a matter of national concern, at last, so I would like to talk about the links between the mining industry, the universities and technological developments. The Australasian mining industry and the mining schools have collaborated closely since the first school was established in 1871 and during those years there were a series of remarkable technological developments. For example:In the late 1880s George AndersoIl Richard developed chloride leaching of gold at Mt Morgan. This made a large difference to the wealth of Mt Morgan Mining Ltd.In the mid 1890s Robert Sticht demonstrated that pyrite smelting was an economically feasible process at Mt Lyell and the wealth which came to Mt Lyell Mining Co from his outstanding work made it one of the great companies in the country.During the first 15 years of this century flotation was developed at Broken Hill and it has proved to be one of the great technological inventions of this century.In the 1920s G K Williams started his outstanding work on lead smelting and refining at Port Pirie, this was work which ultimately re-wrote the text book on lead metallurgy and established Port Pirie as the mecca for lead metallurgists.In the 1920s also Frank Stillwell, later joined by Austin Edwards, established the new science of mineragraphy at the University of Melbourne. They were both great geologists, both were superb scientists and oddly enough both were outstanding athletes.In the 1930s Dr Ian Wark, a man in the front rank of Australian scientists of any period, started his outstanding work on flotation, work which resulted in a text book which remains a leader in its field today.In the 1930s also Arnold Black at Broken Hill South Ltd picked up the work which had been done at Mt Lyell many years previously and eventually wrote the papers on hydraulic fill which demonstrated that he led the world in fill technology. What a remarkable story of achievement it was, it laid the groundwork for the great industry we have today. It was possible because the industry was well supported by outstanding university schools and I would like to talk about some of these.

Jan 1, 1989

By Magne L, Barria J, Castro O, Menacho J, Gonzalez GD

An extensive experimental campaign was developed in a continuous 6 x 2' (D x L) pilot scale SAG mill. The effect of the feed flow rate, feed solids concentration, ball filling fraction and feed size distribution, over the mill performance was investigated. The residence time distribution (RTD) for the fine material was measured in every test, in order to detect changes in the mixing characteristics of the mill under different operating conditions. Based on phenomenological considerations a state model of the SAG mill was developed, which independently incorporates mechanisms such as: grinding, mass transport and classification in the grate discharge. These can be parametrised using information and optimisation software. This comminution model extends the compensation condition, which is a conventional hypothesis for ball milling, to the semi-autogenous mill grinding. The mathematical analysis of this hypothesis, applied to SAG mills, allow the reduction of the number of parameters in the model, using the relationship Ki = (1-bii)Si, where b and S have the conventional meaning. Therefore, the distribution fracture matrix bij and the specific fracture rate SIE are grouped in just a single diagonal matrix Ki.

Jan 1, 1993

The effects of changes in sintering bed height, coke fuel, suction and basicity on sinter productivity, physical strength and mineralogy were determined. It was found that, for a given iron ore, there is a narrow -coke range which maximises sinter strength, irrespective of bed height (in the range 300 to 500 mm) or basicity (in the range 1.2 to 2.2). Increases in bed height, at a constant coke level, improved the physical strength of the sinter. Productivity increases were obtained by increasing the sintering suction but, at coke levels other than the optimum, these *ere somewhat offset by the decrease in sinter physical strength. At basicities higher than 1.2 (i.e. 1.6, 1.8 and 2.2) there was a narrowing of'the size range of product sinter, with a decrease in the percentage of top size material, and a decrease in the amount of fines produced. Changes in coke, bed height and basicity exert major effects on sinter mineralogy, while the Nagoya index was mainly influenced by cote and bed height Changes.

Jan 1, 1975

By J F. H Thompson

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Mineral exploration and mining are challenging businesses. Remote and at times harsh conditions have always made it difficult for exploration, but modern explorers also have to deal with cover, numerous technologies, an explosion of data and critical early community engagement. Mining deals with the reality of moving and breaking thousands of tonnes of rock each day to extract what can be a very minor component of economic value, and, furthermore, society expects that this will be done in a clean and sustainable manner. The exploration and mining challenges appear disparate, but they are intimately related.Although not widely appreciated, both exploration and mining have a long tradition of innovation. Over the last 50 years, major step changes in exploration have resulted from radical advances in our understanding of ore forming processes, new geophysical, geochemical and remote sensing technologies, and new ways to integrate and interrogate data. Over a more extended period, close to 100 years, mining has developed bulk surface and underground methods, selective extraction through flotation and leaching and global positioning system–geographic information system control systems that collectively facilitate mining at a massive scale. And yet, in spite of these successes and the boom that we have enjoyed in the last ten years, the industry is under pressure and the need for innovation and change is paramount.The major drivers for innovation are the need for increased quality in discoveries and mines and the need to interact effectively with communities and jurisdictions such that the benefits of quality mines are recognised and enjoyed widely.We are still making new discoveries around the Pacific Rim and elsewhere, but many argue that the quality – grade and accessibility – of these discoveries is decreasing. The net result is that explorers are delivering resources and reserves for development at lower grades and with higher capital and operating costs than current operations. For mining, the increasing age of many existing operations contributes to increasing costs, which, when combined with decreasing cut-offs and lower grades, also results in declining quality. The combined picture does not look good.Just as the pressure to improve performance and margins in the face of declining inputs increases, we are simultaneously faced with increasing societal demands for improved environmental performance and sustainable practices. This is most apparent at the local, community level, where opposition ultimately leads to delays or even cancellation of new projects. Quality is again the issue – quality of the initial and ongoing engagement and quality of the proposed mine in terms of environmental and economic performance.CITATION:Thompson, J F H, 2015. Exploration and mining – the need for innovation , in Proceedings PACRIM 2015 Congress, pp 45–48 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By K Ellis, B Lumsden

A full-scale statistically-based on/off plant trial of a new flotation conditioning technology designed to improve fine mineral recovery was undertaken to determine whether the recovery of selected fine sulfide minerals can be increased. The technology is selective for certain sulfide minerals only, including chalcopyrite and sphalerite. The technology has been shown to selectively aggregate the fine chalcopyrite and sphalerite minerals giving increased flotation recovery. The plant trials have shown an increase in the mineral recovery, without decreasing selectivity. Size by size recovery shows a significant increase in the fine (

Jan 1, 2005

This method determines tellurium at concentrations down to 0·01 p.p.m., with geochemical accuracy. Tellurium is volatilized from the rock at 800°C in the presence of sulphur from decomposing pyrite, condensed, dissolved, and finally determined by atomic absorption in a long tube burner. The distribution of Te is shown near some gold lodes at Kalgoorlie. Lastly, a method of synthesizing Te-free pyrite from sulphur and ferrous sulphate is described.

Jan 1, 1969

The area (330 sq. miles) shown on the map of the Brocks Creek District (Fig. 1), was mapped by the Northern Territory geological party of the Aerial, Geological and Geophysical Survey of Northern Australia. This work was done in two stages:-(i) In 1935, an area of 30 sq. miles around the Golden Dyke mine was mapped by P. S. Hossfeld, Senior Geologist, and A. H. Voisey, Assistant Geologist. The results were described in a detailed report (10).(ii) In 1939, an area of 300 sq. miles in the Brocks Creek district was mapped by C. J. Sullivan (Senior Assistant Geologist), and V. M. Cottle and S. N. Kiek (Assistant Geologists) under the general supervision of P. S. Hossfeld (Senior Geologist).An outline structural map, together with some geological notes was published (1), but that map does not show the amphibolites, and the relationship between ore occurrence and general geology is not emphasised. The publication of the detailed maps and reportwas postponed indefinitely as a result of war. The original mapping was based on air photographs with a scale of approximately 1 in. to 1,200 ft., and all detail which could be shown at that scale was mapped. Features recorded included rock types, details of structure, mineralisation, and surface workings, creeks and soil boundaries. Underground mapping was also carried out. The present map is much simplified from the original, but it is hoped that it shows sufficient information to reveal close relationship between structure, granite, sills of amphibolite and gold occurrence. About 50 per cent. of the area is covered by deep soil or alluvium, and in these portions the geology of the underlying rocks was not determined with accuracy, though in many places strike trends could be deduced from air photographs.Because the A.G. & G.S.N.A. had published the geological notes and map referred to above, and because the publication of the detailed report and maps is still postponed indefinitely, approval has been given by the Bureau of Mineral Resources, Geology and Geophysics (which took over the affairs of the A.G. & G.S.N.A. at the termination of its operations) to the preparation of the present paper so that information would be available to the public.The views expressed in this report are those of author. The results of the investigation suggest that in areas where granites are predominantly concordant with bedding, ore deposits may be found at approximately the same stratigraphic horizon. It is thus important to correlate beds even though their relationship may have been obscured by faulting and folding.

Jan 1, 1950

By S J. Clarke, G Sieders

Double corrosion protection (DCP) rock bolts have evolved to become complicated assemblies comprising numerous components. This complexity is mainly associated with durability considerations including potential exposure to adverse groundwater conditions and ensuring separation of dissimilar metals within the bolt assembly itself.Recent progress in the construction of glass-fibre reinforced polymer (GRP) rock bolts have the potential to provide a viable alternative to conventional steel rock bolts in civil tunnelling applications. The durability of the material results in a much simpler bolt detail and permits the use of resin rather than solely cement based grouts.This paper presents the findings of the comparative structural testing of GRP bolts with conventional DCP steel bolts. The axial load performance, including stiffness, ultimate capacity and ductility of bolts are compared. Shear behaviour of bolts is considered, including durability issues associated with damage to the plastic sleeve used in DCP bolts.The paper also considers other issues which are relevant to the design of temporary and permanent rock bolts used in tunnel support, such as initial tensioning and grouting. Long-term performance, including durability and creep are also reviewed.CITATION:Clarke, S J and Sieders, G, 2014. Comparison of glass-fibre reinforced polymer rock bolts with double corrosion protection steel rock bolts for use in tunnel applications, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 237–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By L Eriksson, D Penn, J Appelgren

Atlas Copco, a leading supplier of equipment and services to the mining and construction industries, is consistently pursuing its strategy to offer the most productive and economical solutions by continuously offering new innovative products. These are, in most cases, developed and tested in close cooperation with demanding end users before being officially launched on the international market. The demands for higher productivity and improved overall economy have resulted in systems for automation of the drilling cycle and also tools for integrating the drilling equipment to the production control system used by the customer. In terms of improving the blasted material quality, the company has placed emphasis on accuracy in the drilling process and documenting what has been drilled. By applying state of the art technology to the common automation platform, developed for the surface drilling market, major steps in improving overall drilling productivity and blasting performance have been achieved. This paper will give some examples derived from the latest development of solutions for the companyÆs surface drilling products.CITATION:Appelgren, J, Eriksson, E and Penn, D, 2012. Rotary drilling automation increasing operator productivity and drilling quality, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 13-18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By Rubisov DH

This paper is related to the problems of the mathematical modelling of vibrating screening process and to predicting the screening operation results. The authors propose a model of screening based on the interpretation of granular material segregation on a screen surface as an instantaneous process. Results show an agreement with laboratory and pilot plant tests. Derived formulae can be used for screen sizing and screening result estimating.

Jan 1, 1993

The QSL continuous lead smelting process incorporates two basically different pyro- metallurgical operations: roast-reaction, smelting of galena concentrate, followed by carbothermic reduction of some by-product lead oxide slag. Both steps are performed simultaneously in separate compartments of a long horizontal cylindrical reactor, which is lined with fused chrome-magnesite bricks. This converter-type reactor contains a liquid bath consisting of a shallow layer of lead bullion with a superimposed layer of slag, the lead content of which is gradually reduced from about 50% to discardible levels. Metal relative to slag, and slag relative to the gas phase are in continuous countercurrent motion. A lead well is arranged at the flue end of the reactor, and an overflow tap for slag at the opposite end. Tonnage oxygen for oxidation and smelting of the charge, and sub- stoichiometric mixtures of pulverized coal and oxygen for reduction and heating of the slag, are directly blown into the bath using fluid-protected Savard-Lee injectors. High gas-liquid momentum transfer ensures intensive local mixing, and enables rapid mass and heat transfer.

Jan 1, 1984

By Niemann G

The paper addresses certain mining provisions of the Aboriginal Land Rights (Northern Territory) Act 1976 and the development of Mining agreements negotiated pursuant to Section 43 of the Act. Difficulties for miners and Land Councils alike arising out of the operation of the Land Rights Act will be discussed. Possible scenarios for the resolution of these difficulties will be proposed.

Jan 1, 1984

By M A. Llano-Serna, D J. Williams, L Bu

Tailings dam failures continue to occur worldwide at an unacceptable rate, averaging two events annually over the last 100 years. Furthermore, tailings dams continue to grow in size, increasing the potential release of tailings and water should they fail. Tailings are generally deposited in a slurry state, with the potential to flow if containment is lost. Understanding the generation and propagation of excess pore water pressure on failure is critical to predicting the flow and run-out of tailings. This paper presents numerical modelling using the material point method indicating that tailings run-out processes may be self-enhanced by the excess pore water pressure induced during the collapse of the containment. Moreover, it is shown that geomorphological features, such as the slope and its surface roughness downstream of the tailings dam, influence the pore water pressure dynamics upstream of the advancing toe.CITATION:Llano-Serna, M A, Bu, L and Williams, D J, 2018. Excess pore water pressure induced during tailings run-out, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 377–383 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018