Search Documents

By X X. Qiu, T Zhang, B L. Wang, X Qiu, Y H. Du

This paper summarises the information about current state of eco-environmental problems, geological disaster and mining waste causing during the process of limestone mining. By comparing the management experiences of limestone mines in other countries, management problems in China have been discussed and improved management options have been proposed here. These options include: accelerating the process of legislation, promoting and strengthening environmental impact assessment for limestone mine, and increasing compensation requirements according to the local eco-environment conditions.CITATION :Wang, B L, Qiu, X X, Qiu, X, Zhang, T and Du, Y H, 2012. Eco-environmental problems caused by the process of limestone mining and management options, in Proceedings Life-of-Mine 2012 , pp 357-360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

The following data cover a phase in the systematic testing of gold deposits which does not appear to have been specificalIy investigated.In boring either secondary or primary deposits, gold, by virtue of its high specific gravity, will tend to migrate downward, below the driving shoe or bit, and thus cause misinterpretation of value unless final recovery Can be effected after the hole has been bottomed.Unlike fortuitous and non-recurrent errors, due to, say, running ground, "pile driving" or rock fractures, systematic error due to migration may be unpredict.able from operating data alone, and, therefore, result in serious miscalculation of the weighted average upon which the engineer's recommendation is based.Applied to diamond drilling, loss by downward migration appears to have been largely responsible for distrust of sludge assays in the past. On the other hand, although modern practice rightly trends towards an integration of both core and sludge samples in borehole valuation, the possibility of systematic loss must be investigated when using combination graphs such as those of Longyear, Moehlman and WeIler. If the sludge value is incorrect the combination graphs will serve solely to stultify the core valuation.It appears to be axiomatic that: 1. With full core, sludge assays are of minor import.2. With recovery above 90%, differentjal grinding, of the high grade sections may have occurred, and this c!ln be corrected only by the us.e of cOJ;rect sludge valuation.3. With core recovery less than, say, 70%, no accurate valuation is possible without integrating the sludge assay.4. With less than, say, 10% core recovery, the sludge assay affords the sole basis of evaluating a borehole which may have cost many hundreds of pounds.The conditions demanded for reliable sludge valuation have, in practice, been restricted to high quantitative recovery and return of nearly 90% of the drill water. It is submitted, however, that the following additional knowledge is required:1. The nature of gold distribution in the ore.2. The lifting power of the return water column, which can be gauged by the maximum quartz particle, provided that the degree of "hindrance" can be determined.3. That all gold has been cleared from the bottom of the borehole immediately after it has passed through the orebody.The three cases discussed hereunder are offered not only as proof of the thesis, but also in the hope of promoting discussion on the interpretation of borehole values and on methods for saving free gold in the sludge. The fact that two of them cover alluvial boringand the third diamond drilling has resulted in this attempt to reduce the behaviour of free gold to a basis common to all types of boring.

Jan 1, 1950

By Bell I. F

In 1985, ZC Mines (now Pasminco South) had been unprofitable for some years due to a combination of high operating costs, low metal prices, low head grade and an aging and inadequate mining infrastructure. However, the resource of metal in the ground was still of world class, even after some 80 years of mining. A major study, which was to be of two years duration, was therefore commenced to establish a practical and profitable long term mining strategy and to cost the infrastructure options needed for its support and thus form the justification for a capital expenditure program to take the mine profitably into the 21st century and its second century of operation. This paper discusses the rationale behind the methodology adopted and the nature of the results achieved in one aspect of the study - the determination of the mineable resource and the relationship between the head grade/quantity of the economically mineable resource and the variables of cut-off grade, cost structure, annual production rate and metal prices/exchange rates. The basis of the study was the designing of some 5000 scopes to mine out the entire resource for a range of cut- off grades and the assembly of the detailed physical data thus obtained in a stope-by-stope data base for financial and other analysis. Those scopes which were shown to be economically mineable were then scheduled for two optimum annual production/cut-off grade/metal price combinations to provide life-of-mine cost and value of production cash flows.

Jan 1, 1992

Various methods and software have been trialled for simulation of Au grades at Boddington Mine. This covers in-house and public software as well as sequential and turning bands methods. The diversity of options was further expanded with comparison of point and direct block simulation. Some difficulties were encountered in incorporating high-grade restrictions. Altering parameters or software can make very significant differences and give results varying from estimations. This paper details a new simulation run with validation and tests for local calibration (or progressive correction) of the simulations to the estimations, focusing on reproduction of statistics. This approach brings to the forefront the question æwhat is the purpose of the simulations?Æ Results and some ideas for future applications at Boddington are summarised.

Sep 26, 2011

By W Assibey-Bonsu

The paper provides a brief review of the multivariate uniform conditioning and the localised multivariate uniform conditioning techniques and presents a case study based on a porphyry copper gold deposit in Peru. Two other important scenarios have been investigated and will be particularly emphasised: The recovered selective mining unit (SMU)s depend on a combination of copper and gold content, which can be expressed by means of ænet smelter returnsÆ (NSR). Two approaches are compared. Firstly, the application of a composite cut-off on NSR on the joint distribution of each grade and the application of uniform conditioning to three variables is investigated, ie for the first approach NSR is used as the main variable. The second approach considers copper as the main variable. In the case of multiple domains the procedure used to apply the technique to process mixed panels is clarified and recommendations are made.

Sep 26, 2011

Jan 1, 2004

This paper will first discuss the fundamental requirements for reliable discharge of backfill by gravity alone at high per cent solids. This discussion will include brief mention of the underlying principles of saturated solids flow contrasted to that of stirred tank or dilute discharge systems. Here the need to possess full knowledge of the flow properties of the stored material will be highlighted. In addition proper account must be made of the silo overflow weir and settling capacity to match plant throughput. Here opportunity will be taken to highlight the complexity of this multi-phase flow situation as well as the general yet paramount requirements for reliable solids flow. It will be shown that by proper attention to the multi-phase considerations gravity discharge of slurries as a consolidated bed with minimal water content is possible. Such high solids discharge results in greatly reduced demand for process water. In addition pumping costs are reduced as is the delay time associated with the mine drainage operation. Confirmation of successful applications will be highlighted by reference to several recent case studies. In the concluding phase mention will be made of the key yet very simple and effective operation techniques which enhance reliable discharge. The simplicity and reliability of properly designed gravity discharge backfill tank systems suggests increased application of this technology by the mining industry.

Jan 1, 1998

An Application of Depressant BK510 in Separation of Molybdenite and Bismuth by Flotation

Sep 13, 2010

Despite a long history of production of industrial minerals and rocks, New South Wales still offers significant opportunities for exploration for and development of these minerals. Exploration for opal, sapphires, and zeolites in the State has been particularly encouraged by pioneering geological studies by the Department of Minerals and Energy, which have resulted in the development of important new geological concepts and exploration techniques. Large areas with potential for these minerals have not yet been tested. In the case of sapphires, the studies have identified a new type of deposit which is'the source of most of the sapphires mined from alluvial deposits. Recent price increases for heavy minerals, a re-evaluation of previous exploration in coastal regions, and a recognition of suitable environments in inland New South Wales have stimulated renewed exploration both onshore and offshore and have led to increased production. Significant potential also exists for development of a number of other minerals, including: topaz, which occurs in large, unusual and perhaps unique deposits in northern New South Wales; dimension stone (particularly granite); bentonite; diatomite; and silica for metallurgical use. Potential also exists for development of construction material resources, particularly construction sand, which is in short supply in the Sydney region.

Jan 1, 1989

THE machine from which the following results were obtained makes one of a row of seven at work in the Junction North, Concentration Mill at Broken Hill, New South Wales. It consists essentially of a belt for dressing purposes, which travels round two 12-in drums situated at either end of a wooden frame. This frame is supported on wooden legs, and the whole is affixed to two iron castings, one on either side of the frame. A to-and-fro motion is obtained from an eccentric shaft, which, together with the stationary end of the supporting legs, is carried by the iron castings. A belt drive to the forward drum provides a constant rate of travel to the dressing belt.The top half of the dressing belt is supported on 3-in rollers spaced about 12-in centres along the frame of the vanner. A fairly thick dressing belt is used, and no trouble whatever is experienced from the formation of gutters between the rollers.These belts are 28 ft 4 in long, 4 ft wide, 3-16 in thick, and are made of two-ply 32-oz duck, with a coating of rubber on either side. The surface available for dressing is about 10 ft 6 in x 3 ft 8 in- ie, about 38'5 square feet. The machine is driven atthe rate of 245 i-in strokes per minute, while the dressing belt travels at 15 feet per minute...

Jan 1, 1909

By J J. Van Wijk, A R. Penney

Successful management of geotechnical risk at a mining operation is more than just having a good ground control management plan or using advanced numerical modelling and the latest monitoring technologies. The fundamental requirements for effective geotechnical risk management include identification of potential failure modes, identifying and implementing appropriate controls, and demonstrating the effectiveness of those controls. Effective geotechnical risk management requires an integrated approach by confirming that appropriate risk management systems have been identified and implemented (management plans, procedures etc), and that these systems are executed consistently in the field across all working areas. Development of a thorough integrated auditing process executed by an experienced team of technical subject matter experts with substantial operational knowledge, provides a more complete picture of catastrophic hazard management. Following consistent evaluation criteria allows benchmarking of systems and implementation compliance between the sites being audited, and the results can then be ranked against other operations in an industry database.

Nov 29, 2022

By S Kundu, J Zanganeh, D Eschebach, B Moghtaderi

The concentrations of methane and coal dust vary from one location to another in underground coalmines. In the presence of an ignition source, such as static electricity, these mixtures can initiate explosions and consequently cause massive destruction. Research data can help in understanding the level of hazards and associated risk these flammable mixtures can produce. For instance, the level of peak explosion pressure and flame speed can be well understood from experimental and numerical research data. With this aim, methane–air mixtures and methane-coal dust-air mixtures were employed in a ducted spherical vessel. According to literature, the maximum value of peak explosion pressure can be obtained in vessels of spherical geometry when compared to vessels of other geometries. Thus the values of explosion parameters generated from spherical vessels can be incorporated in understanding the highest level of hazard that can occur in a real world scenario.In this study, the duct integrated with the vessel resembles any channel or pathway connected to a methane and/or coal dust rich area in the mine. Experimental investigations emphasise that the severity of explosion in the explosion zone transmits to the channel or pathway. The length of the channel or pathway also plays an important role on the values of explosion parameters. The greater the length of the channel or pathway, the higher the explosion pressure is and therefore the higher the destruction. Ignition energy and concentrations of methane and coal dust were varied in collecting experimental data. The data of explosion parameters thus obtained can be employed in addressing hazard mitigation strategies in coalmines.CITATION:Kundu, S, Zanganeh, J, Eschebach, D and Moghtaderi, B, 2017. Incorporating research data in addressing methane and coal dust fire, and explosion hazards in coalmines, in Proceedings Australian Mine Vent Conference 2017, pp 175–180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By R Bearman

The importance of crushers in the mining industry declined with the introduction and resultant dominance of AG and SAG based circuits, but the recent move to consider more energy efficient circuits has caused the industry to re-consider the role of crushers.Different types of comminution equipment have different efficiency in the way the energy is applied in the size reduction process. Because of the general trend towards more sustainable production processes and emission of carbon dioxide, energy use has become more important. To fully understand how crushers can contribute to optimising the energy application in comminution circuits, detailed models of process performance are required. Such models need to take into account the mechanical design factors and how the crusher performance changes in response to feed conditions, the control strategy utilised and the wear of the crusher liners.It is also critical to analyse the total circuit, not just the individual crushers. To fully understand the performance of the entire circuit, dynamic simulation should be applied. Without the holistic understanding of the total circuit and the incorporation of transient effects, the full circuit performance cannot be adequately determined and the true energy picture will not be quantified.Based on detailed mechanistic modelling of crushers by the authors and the application of dynamic simulation, the opportunities to optimise the use of crushers for energy efficiency are examined.

Aug 8, 2011

By B Murphy

Traditionally comminution optimisation has been focused on energy minimisation, whereas flotation optimisation has been focused on recovery improvement. One of the largest, if not the largest, operating cost over the life of a flotation circuit is electrical energy. With increasing pressure on operators to lower production costs and the cost of energy increasing, reducing the energy consumption of the flotation circuit can be beneficial to site economics. This paper reviews the use of energy by mechanically agitated flotation machines and discusses the measurement and benchmarking of energy consumption in modern flotation concentrators. Opportunities for improving flotation energy efficiency are also identified.CITATION:Murphy, B, 2013. Flotation energy consumption and opportunities for improvement, in Proceedings MetPlant 2013 , pp 399-412 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

Bioleaching of E-Wastes

Sep 13, 2010

By R M. Yanamandra, S K. Tripathy, N Mangadoddy, P Sudikondala, P Ankireddy

Spiral concentrator is one of the most commonly used gravity concentration devices in mineral processing. The particles are classified based on their specific gravity and size. The present work analyses the experimental and numerical investigations of the water flow field, such as fluid depth and free surface primary velocity of two high gravity spiral concentrators at different flow rates. The measurement techniques use a flow depth gauge and flow visualisation technique adapting lycopodium powder as the tracer. Flow features in terms of liquid depth and primary velocity at the free surface of the flow are captured across the trough in two different high gravity spirals. A highspeed motion camera with an imaging frequency of 5400 frames per second and 768 × 768 pixel resolution is utilised to track the tracer particles in the liquid flow on the dark surface background. Further, the two-phase flow is studied numerically on high gravity spirals based on the volume of fluid (VOF) approach utilising the RNG k-ε model and Reynolds Stress Model (RSM) for predicting the fluid flow on trough surfaces such as water depth and free surface primary velocity. The CFD predictions of the flow field for the two spirals are attempted to validate against experimental data. The high gravity spiral concentrators show lower flow depths and free surface primary velocities but steep velocities on the outer trough zone compared to that of low gravity spiral concentrators (conventional coal spirals). Among the computationally tested high gravity spirals, higher pitch and higher secondary slope design shows greater flow characteristics.

Aug 24, 2022

By Ring R. J, Waters D. J, Vautier F. E, Fulton E. J

Laboratory leach tests have been carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's acid (permonosulphuric acid) as an alternative oxidant to pyrolusite in the leaching of uranium ores. Results demonstrated that Caro's acid reduced acid consumption in leaching and the lime required for neutralisation of tailings liquor. The uranium extraction was unaffected by choice of oxidant.Following this study, Interox Chemicals Pty Ltd arranged a plant trial using Caro's acid at the Nabarlek uranium mill of Queensland Mines Ltd. The trial confirmed that significant savings in acid and lime usage can be achieved under plant conditions.Plant operations also demonstrated that Caro's acid has a number of significant operating advantages over pyrolusite.Queensland Mines Ltd have recently decided to convert their leaching process from pyrolusite to Caro's acid. The new system is expected to be fully operational by mid 1983.

Jan 1, 1983

By D Thornton, B Smith, S Demey

Mine to Mill (MTM) optimisation, a total systems approach to the reduction of energy and cost in mining and mineral processing operations, is well-established technology. However, successful applications of MTM optimisation have been largely confined to gold, copper and lead/zinc semi autogenous grinding (SAG) operations, where the goals of tweaking the blast design to increase fines and hence throughput through the mill have been relatively easy to meet. The application of MTM optimisation in a more demanding environment, like that of a multi-stage crushing and screening aggregate operation, was conceived as part of a Department of Energy (DOE) initiative in 2004, aiming to reduce the energy consumption in the US aggregates industry. Two quarries operated by the Luck Stone Corporation of Richmond, Virginia, were selected for the demonstration sites. Dealing with ore variability and a requirement to maintain a fixed feed size distribution to the tertiary plant, whilst still aiming to increase yields of saleable products, presented some unique challenges. Despite these variables, the implementation of the MTM approach at Luck StoneÆs aggregate plant in Pittsboro, North Carolina, has led to a tangible improvement in productivity, particularly in the primary and secondary plants. The successful outcome was dependent upon several key factors, including reliable blasting and processing models, careful analysis of the rock conditions and plant configuration, understanding and buy-in from the Luck Stone operations staff, excellent collaboration with Virginia Tech staff and students, and long-term monitoring made possible through comprehensive PLC logging. This paper presents a review of the work conducted at the Pittsboro quarry and highlights the key reasons behind the successful implementation of the MTM approach in a complex plant environment.

Jan 1, 2007

By P Wilson

The Mt. Wright Underground Mine is located near the town of Ravenswood in North Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited. The establishment of the world’s first Sub Level Shrinkage (SLS) mine from a tradition Sub Level Open Stoping operation has proven to be a geotechnical challenge which has required tailored solutions to overcome unique issues. This paper will be broken into two distinct sections that will outline: a brief overview of the mining method and how the SLS method was chosen; and how the SLS is managed and key geotechnical learnings. The story of the world’s first SLS originated from the need of a bulk mining method to ensure the viability of Mt. Wright into the future. Traditional bulk mining methods such as; Block or Sublevel Caving were originally ruled out due to the low natural ‘cavability’ of the orebody and the proximity of the orebody to existing major infrastructure (Decline, Ventilation Rises and Egresses). The first section of the paper will outline the key geotechnical information that helped decide the SLS method in addition to how continuous backfill influenced the design. The second section is intended to address issues that the geotechnical engineers encountered since the inception of the SLS. The feature topic of this section is mining induced stress. Like most bulk mining methods, Mt. Wright had success when the production front was running parallel to the stress (production front being ‘shadowed’ from the stress). This was until a design change, forced by a splitting ore body resulted in this shadowing effect becoming harder to achieve. As a result, rehabilitation and production hole re-drilling become a regular occurrence, which teamed with a strict set of access controls made the production cycle longer and harder to complete. CITATION:Wilson, P, 2018. Mt Wright – geotechnical learnings from a sub level shrink, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 119–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Observed mineral assemblages in the Mt. Lyell copper deposit can be correlated with phase equilibrium investigations in the systems Cu-Fe-S and Fe-Zn-S. The trend of crystallization (or paragenetic sequence) of the ores is reflected in a progressive increase in the Cu: Fe and metal: sulphur ratios of the assemblages. This trend agrees with the regional zoning of the district. Tentative relationships between the paragenetic sequence, sulphur vapour pressure, and temperature are presented graphically. The absence of a suitable geological thermometer prevents precise elucidation of the range of temperatures and pressures which existed during crystallization.INTRODUCTIONRecent phase equilibrium investigations of metal-sulphur systems at the Geophysical Laboratory, Washington, D.C. provide valuable information on the stability relations of a number of important sulphide minerals. This data, when applied to natural ore deposits, may be expected to clarify two special problems which confront the ore petrologist seeking to interpret observed data in terms of a particular physical and chemical environment of ore deposition. These two problems are the sequence of formation of sulphide minerals (commonly designated the paragenetic sequence) and an elucidation of the range of temperatures and pressures which existed during crystallization. The object of this paper is to make such an interpretation of the copper mineralization of the Mt. Lyell district, Queenstown, Tasmania.The following abbreviations are used in this paper:py = pyrite, cp = chalcopyrite, en = cubanite, bn = bornite,cc = chalcocite, cv = covellite, dg = digenite, id = idaite,po = pyrrhotite, v = sulphur vapour.GEOLOGICAL SETTING AND MINERALIZATIONThe general geology of the Mt. Lyell district is well known through the recent work of Wade and Solomon (1958). The host rocks are a series of quartz-chlorite-seri-...

Jan 1, 1963