Search Documents

The acid plant consists of the following units: 1. Glover tower. 6. Mills-Packard type chambers. 3. Reaction towers. 6. Gay-Lussac towers.The sulphur dioxide bearing gases, used in the manufacture of the acid, are obtained from the roasting of zinc concentrate. Six Herreshoff type furnaces are available, each with an effective hearth area of 520 sq. ft.The concentrate contains approximately 30% sulphur, of which about 72 is ultimately recovered as acid. The oxides of nitrogen are added to the gases in the requisite proportions partly from nitrous vitriol and from nitric acid in the Glover tower, and partly from nitrous vitriol in some of the chambers and connecting flues.The acid leaving the Glover tower is cooled by the ordinary water-cooling coils, while the cooling of the chamber gases is effected by circulating water over the outer surface of the chambers, and by spraying nitrous vitriol and weak acid into them.Flow of gases throughout the plant is regulated and controlled by means of regulus metal fans, fitted with variable speed gears.

Jan 1, 1934

The No. 2 Ore-shaft, at Mount Isa Mines Limited, involving the use of boreholes as ropeways for the upper portion thereof, constitutes, we believe, a unique feature in hoisting installations. The boreholes were sunk from the surface to a depth of 390 ft., thus eliminating the necessity of erecting the hoist at an underground location or construction of the shaft for this distance. Fig. 1, a diagrammatic cross-section through the shaft, shows the complete installation from the surface down to the first loading station below No. 7 haulage level.During the latter part of 1936, conditions encountered in sinking the Main Ore shaft made it impracticable and uneconomical to continue deepening it to serve haulage levels below the present No. 5-level. Plans were therefore made for an interior shaft, to serve new lower levels, that terminated above No. 5-level so that ore hoisted could be drawn off on this level and transported to the Main Ore shaft for final conveyance to the mill crude ore bin.Referring again to Fig. 1, it is apparent that the section above No. 4-level, if opened out to full shaft size, would be inoperative and would serve no useful purpose except, possibly, as a ventilation duct. Original plans therefore did not include continuation of the shaft above No. 4-level. Excavation of a hoist room upon No. 5-level; erection of sheave wheels just below No. 4-level, and a long inclined ropeway leading from the hoist to the sheaves, were incorporated in the general layout. Work on the lower sectionof the shaft had started when the idea of locating the hoist...

Jan 1, 1939

By J V. Lawless

Mineralisation processes in epithermal deposits in the North Island of New Zealand are best illustrated by considering the two most productive deposits: Waihi and the Thames Bonanza Zone (TBZ), which have different mineralogies and ore shoots geometries. These two deposits can be taken as typical of certain styles of epithermal deposits worldwide, and recognition of their differences can be used to develop mineralisation models of predictive value. Waihi, the major economic producer in the Coromandel Volcanic Zone (CVZ), has laterally near-continuous ore shoots over a vertical interval of 600 m which consist of quartz, chalcedony, pyrite, base metal sulphides and electrum. They are found in the foot wall of earlier quartz veins which contain quartz pseudomorphs after platy calcite and adularia. The Thames Bonanza Zone which was the second biggest producer in the CVZ has discrete near-vertical ore shoots over 300 m vertically, which consist of quartz, pyrite, base metal sulphides, electrum and in their upper parts barite, that are enclosed in veins of quartz.   The gold mineralisation in both deposits is considered to be a co-precipitate with pyrite, with that at Waihi produced by prolonged boiling in an upflow of a hydrothermal system. That at the TBZ was produced by mixing a deep water primed for gold deposition by prior limited boiling, with an oxidised condensate of the steam released by the boiling, in an outflow proximal to the system's upflow.

Jan 1, 1997

Spectrum Resources commenced operations as a public listed mining company in August, 1983, with a variety of precious metal projects in New Zealand. At that time the outlook for most mineral commodities, with the notable exception of precious metals, was decidedly gloomy. Metal prices were depressed and demand forecasts were universally gloomy. Against this background the company reviewed the non-traditional metals sector to try and identify a 'new' metal with an above average demand growth and market value. Lithium, a commodity with exciting new applications in storage batteries and alloys, met both criteria. Annual world consumption of lithium is around 7000 tonnes; current prices are around $NZ40/lb for lithium metal and demand growth is projected at five to seven per cent per annum. Geothermal fluids at Wairakei and elsewhere contain anomalous amounts of lithium and in May, 1984, the Chemistry Division of DSIR was commissioned to carry out a literature survey on the possible recovery of lithium and other minerals from geothermal waters. The survey results were encouraging and the company subsequently negotiated exclusive access rights, for research purposes, to geothermal discharge fluids from the Wairakei and Kawerau geothermal fluids. Most of the subsequent investigations reported here were carried out by Chemistry Division, DSIR, under contract to the company with some assistance from the Industrial Processing Division, DSIR.

Jan 1, 1986

The theme of this paper is the development of-the project feasibility study which includes discussion of the work which is carried out in preparing the project feasibility study, the necessary evaluations and structures that are employed to ensure that not only does the feasibility study itself stand up to scrutiny and is sound, but also that the investment the company is proposing to develop, "the project", is an investment decision which will represent good returns to the company. This theme is particularly relevant when there are competing divisions within the company and only limited cash resources are available to make the correct investment decision. Thus various potential investments may be evaluated against each other to determine which project will be given the go ahead for development. This paper will particularly focus on the various investment analysis techniques that are used and discuss the work that is required in preparing the project feasibility study and specifically the interaction of the project team members and the thought process that must be undertaken to complete the project feasibility study. Finally comments will be made on tax planning issues particularly with respect to taxation of gold production to be introduced in January 1991. Some ideas are presented which may help and possibly improve the financial position of the projects being reviewed. Further, it is suggested that the thought process which goes with the financial engineering aspects of a resource project can be widened to take account of taxation issues and tax planning to ensure the rise of the project feasibility and hence the decision to proceed to development by the project sponsors.

Jan 1, 1990

By Ashley P, Neale T

Alluvial gold was discovered on Sudest Island in 1888, and by 1893, an official production of 10 000 oz had been won by expatriate miners from shallow alluvial and colluvial workings. Hardrock sources were located and while one was developed at Mt Adelaide, production is unknown. Sudest Island comprises mostly phyllites and lesser coarse grained rocks which are cut by metamorphic quartz veins and basic (locally shoshonitic) intrusives. Sheared and altered basalts and serpent- inites represent are believed to be elements of an ophiolitic suite inferred to be associated with metamorphic core complex development and thus similar to tectonic environments on Misima and the D'Entrec- asteaux Islands. No epithermal-style quartz suggestive of a target similar to that on Misima Island has been identified on Sudest. A hardrock source for the alluvial and colluvial gold is interpreted to be metamorphic quartz veins similar to those in the Bendigo- Ballarat Zone of central Victoria, possibly remobilising gold derived from the meta- sedimentary and meta-igneous rock pile. The present focus is on development of a small scale alluvial gold mining operation in conjunction with exploration for hardrock targets. This latter programme remains at a reconnaissance stage.

Jan 1, 1991

By D A. McCallum

With depth, many gold ores become sulfidic with minerals such as pyrite, pyrrhotite and arsenopyrite becoming prevalent. In addition, many underground gold mines use tailings backfill to bind and store the waste. In these cases, acid mine drainage (AMD) can become an issue. One approach to the control of AMD is desulfurisation whereby the sulfide minerals are removed prior to disposal. Four sulfide tailings samples, representing different ore types and gold and base metal operations, were selected for assessment and testing using simple physical beneficiation techniques. The aim was to determine the extent to which mineral processing methods were suitable for separating sulfides from non-sulfides and for extracting potentially marketable by-products from the tailings. In order to streamline the testing procedure a simple diagnostic separation technique was developed to enable quick screening of bulk sulfide tailings for suitability for reprocessing. The testing procedure involved detailed characterisation and a sequential set of testing regimes based on simple unit processes including water washing, classification, gravity concentration, magnetic separation and bulk flotation. The preliminary test results indicate each unit process can play an important part in producing effective sulfide/non-sulfide separations and in generating useful by-products from the tailings. Potential valuable products identified include coarse, benign silica sands, bulk iron sulfide products rich in pyrite and/or pyrrhotite, high-grade iron products (magnetite) low in silica, low-volume bulk sulfide concentrates and low-grade molybdenite and talc products. The work presented shows how sulfide tailings can be viewed as a resource rather than a waste stream, and identifies a pathway for developing a more sustainable approach to the environmental management of sulfide tailings for the future.

Jan 1, 2007

Development on the North Kalgurli mine has established a major penetration of ore into calc schist. This is controlled by a system of east-dipping strike faults. Previously, most calc schist ore bodies were regarded as being confined to the quartz dolerite greenstonecak schist contact environment.INTRODUCTIONOne of the most interesting and economically important developments which has taken place in the Kalgoorlie Field over the past 20 years is the proved penetration of ore into calc schist on the North Kalgurli Mine. This is quite extensive, both laterally and in depth, and has occasioned some modification of geological thought in the search for additional ore sources.Ore has been mined in calc schist almost since the first major gold discoveries were made and the principal features of the various types of deposit are well covered in the literature of the field. However, occurrences in calc schist have not been characterised by the same degree of continuity or frequency as the innumerable lode formations in the more favourable quartz dolerite, and there has been a tendency to regard them as isolated and discontinuous ore bearing structures, occurring only under very special conditions.It is not intended to describe the whole range of calc schist ore occurrences but only major controlling structures, whose penetration therein has been definitely established and in which an appreciable amount of ore has been and is still being found. It is considered that similar structures may present a major objective for future exploratory work in other parts of the field.

Jan 1, 1964

B. P. Thomson (South Aust. Dept. of Mines): Dr. A. B. Edwards presents in the published discussion on the above paper, his interpretation of the dolerite dyke-lode relationship as a major objection to the syngenetic origin for Broken Hill ore bodies to which Mr. Condon subscribes.Dr. Edwards claims that the dyke-lode relationships indicate clearly that the Broken Hill orebody was formed after the folding and regional metamorphism of the Willyama Series. Field evidence compels m:e to join with H. F. King (1958), in finding this conclusion unacceptable-as follows:(1) Broken Hill type mineralization, as defined by King and Thomson (1953), is clearly confined by the regional sillimanite isograd and does not extend into the lower temperature almandine and biotite zones as does the Thackaringa type mineralization.(2) In the Corruga area the writer has mapped a dolerite dyke apparently cutting a conformable quartz gahnite lode of the Broken Hill type (see Edwards 1958, p. 12).(3) At the Champion mine a similar lode is cut by a fine grained granite dyke.An alternative history of the dolerite dykes to that given by Stillwell & Edwards (1956, p. 26) appears possible. It has been suggested by the writer in an unpublished thesis, (Thomson 1955, p. 30), that the pyroxenite and serpentine plugs and dolerite dykes are rheomorphic end-products of a complex regional metamorphic and metasomatic process involving the formation of amphibolite and pegmatite. The analogy in composition between the dolerite and normal amphibolite is close (see Edwards 1958, Fig. 1, p. 22).

Jan 1, 1959

By E Villaescusa, A Kusui

The depth of underground mines has been increasing due to several factors, such as material demand growth and improving technology. It is a challenge to understand severe failure mechanisms such as spalling, which is caused by induced high stress. To investigate this failure mechanism under high stress conditions, intact rock blocks with small size tunnel were tested at the Western Australian School of Mines (WASM). The range of rocks, such as sandstone and granite, were drilled (200 mm hole) and tested using a servo-controlled 450 t capacity INSTRON machine. The acoustic emission sensors were attached to the block mass during the experiment to investigate the seismic response prior to spalling failure. The effect of the ground support system towards the failure was also examined by comparing the seismic response of the various ground support schemes.CITATION:Kusui, A and Villaescusa, E, 2016. Seismic response prior to spalling failure in highly stressed underground tunnels, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 689–694 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Removal of Arsenic in Fluorite Ore by Simultaneous Grinding-Leaching with NaHS Generally speaking, a high-grade fluorite ore is converted into hydrogen fluoride (HF), which is essential for the semiconductor manufacturing. With the continuous depletion of resources, novel technologies for processing low-grade fluorite ores are urgently needed, in order to lower the arsenic concentration to less than 100 mg/kg. In this study, a low-grade fluorite ore was upgraded by removing arsenic, which is difficult to remove by conventional method. The mechano-chemical leaching of fluorite ore (i.e. the sample was ground in presence of NaHS, using a beads mill) was carried out to investigate the removal of arsenic from the low-grade fluorite. Experimental results showed that the arsenic concentration was reduced to 73.2 mg/kg.

Sep 13, 2010

By P T. Stoker, A Allman, D P. Carville

Classification of mineral resource estimates is one of the most important responsibilities of the Competent Person. In recent years, classification decisions have been driven more by the detailed block-by-block attributes generated by the now widely applied geostatistical estimation methods, and less by a general geological overview. This is increasingly resulting in æspotted dogÆ outputs, in which blocks of Inferred Resources or unclassified material separate blocks of Measured and/or Indicated Resources, or individual drill holes are surrounded by annuli of Measured and Indicated Resource blocks. Not only are such outputs potentially misleading, since they ignore fundamentals such as continuity of geology and mineralisation between drill holes and the imprecise nature of resource estimation, they can also cause substantial problems for engineers undertaking mine designs and estimating ore reserves, particularly for underground mines. Competent Persons for mineral resources must keep in mind the purpose of their work, and should use their experience and judgement to avoid or smooth out æspotted dogÆ classifications, providing a result commensurate with the level of geological and resource estimation confidence. For their part, ore reserve Competent Persons must understand the resource estimation and classification process, and should question resource classifications that are not consistent with the level of geological and resource estimation confidence.

Jan 1, 2006

The variation of carbon monoxide and hydrogen utilization with the amount of the reductant in the blast furnace bosh gas was investigated for the No. 4 blast furnace at The Broken Hill Proprietary Co. Ltd.iron and steel works. Newcastle. The degree of CO utilization decreased with increasing CO in the bosh gas; the H., utilization increased with the H., content of the gas. Empirical relationships for CO and H., utilization are proposed.H2, is 3-6 times as effective a reductant as CO at present levels of CO (34-39 per cent) and H2 (6-10 per cent) in blast furnace bosh gas. H2, gas injection into the blast furnace is proposed as a means of lowering the coke consumption, and the economics of H2 injection are evaluated.

Jan 1, 1975

By T Nassis, H M. Nel, T du Toit

Assmang Khumani Iron Ore Mine is exploiting the iron ore deposits that can be found in the Bruce-King-Mokaning farm areas in the Northern Cape, South Africa. The Bruce, King and Mokaning (Khumani) deposits are approximately 10 km south of the town Kathu, adjacent to the Sishen Mine. Assmang Limited is jointly owned and controlled by African Rainbow Minerals Limited and Assore Limited.Measurement, calculation and trending of plant throughput and chemical ore properties are critical in maintaining a successful beneficiation operation due to these values forming the basis of decision-making and thus promotion of efficient ore extraction. The Khumani management and engineering information system (MEIS) supplies information on key process parameters to an operational team and is required to do so within an optimal time frame, for maximum impact.Diverse data is put into the MEIS from multiple specialist systems, with interfaces that require manual intervention. Manual intervention is resource and time intensive to the point which limits the effect on the process and decreases the potential for value addition.Automation of interfaces decreases resource and time requirements, standardising plant wide data sources and providing the opportunity to provide specialist system data to decision-makers in a timely fashion, resulting in maximum impact on the process output.Engineering and metallurgical management systems were interfaced at Khumani Iron Mine by means of an automated table which facilitates the transfer of production data validated within the engineering system as input to the metal accounting system. This interface effectively assigns a master to each specialist data set employed for decision-making and delivers accurate process parameters to the production team within an optimal time frame, resulting in increased potential to improve beneficiation efficiency.CITATION:Nel, H M, Nassis, T and du Toit, T, 2013. The role of metallurgical and engineering information systems in the optimisation of iron ore beneficiation processes, in Proceedings Iron Ore 2013 , pp 453-458 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Experiments on High Efficiency Separation of Mixed Plastic Wastes by Vortex-Tube Separator

Sep 13, 2010

By L H. G McClean

Environmental, social and governance (ESG) factors have always been important to the minerals industry and is now considered one of our most important opportunities (and risks). Getting it right from the beginning is critical for the minerals industry, and that starts with mineral exploration. Exploration, or the process of investigation of an economic mineral deposit, is generally low impact and short-term. Exploration operations vary in size and scale and often shift priority, focus and location relatively quickly. Australia is a highly regulated jurisdiction with different regulatory systems and requirements in every state and territory. Most mineral exploration is undertaken by junior exploration companies or ‘explorers’. Exploration companies are lean operations with limited staffing and resources, traditionally with no income apart from funds raised or work through partnerships. Funds are tight and administrative investment is minimised so that investment into activity on the ground is maximised. All these variables mean that understanding and implementation of ESG frameworks for an exploration company can be challenging. ESG is a fast-moving sector with currently multiple frameworks and reporting standards. Interest from community and government stakeholders as well as investors and off-take partners has been growing, with mandatory reporting soon to be implemented. The upcoming changes to the JORC Code will ensure that ESG considerations will be a key component of all public reporting. Resources have been developed to support explorers implement, manage and report on ESG considerations. Due to their scale, agility and direct importance of land access and social licence, many explorers are not the ‘cowboys’ (or ‘cowpersons’) of the industry, but industry leaders in ESG. Strong interest and leadership have led to innovative practices and strongly embedded vertical frameworks that directly contribute to social licence to operate.

Sep 1, 2024

By Gupta R. C

Syria has about 500 million ton deposit of minerals having 34 per cent iron content with alumina and silica as major impurities. Efforts were made to see the feasibility of concentration by four different methods involving washing, high intensity magnetic separation, reduction roasting and magnetic separation and acid leaching technique. It was observed that the reduction roasting with magnetic separation yields a concentrate with high iron (62.3 per cent) content without requiring water which is a scarce raw material in the region. The paper concludes that the detailed study may be made following this route to optimise the process Parameters.

Jan 1, 1999

TSL Concepts and Practical Examples of the Non-Reactive System - Meyco TSL 865 Thin Spray-on Liners (TSLs) have been intensively investigated by mining and chemical industries within the last decade. Apart from the basic concept of spraying thin liners, expectations of the product's performance vary, eg immediate active strata support is seen as a key to control the ground permanently. For many coal mines this is an important factor to reduce maintenance in their roadways and enable permanent production from the long wall. In opposition to a passive mesh system this technology offers immediate active support to the strata. But not only coal mines are interested in TSL technology, there are potential applications in hard rock mines, during shaft sinking, pillar support and as an anti-weathering sealant. This paper will explain the advantages and disadvantages of TSL concepts; it will give examples of successfully applied TSLs with a main focus on the non-reactive and flexible system MEYCO TSL 865 by BASF. Furthermore, it will indicate the limitations and discuss briefly the bearing capacity and reasonable lab testing of such systems.

Nov 25, 2010

By D Kilkenny

Underground contractors in the mining industry must be prepared to take a position at the forefront of innovation of equipment and work methods in order to maintain a competitive advantage over in-house operations and remain relevant. Innovative concepts such as split-feed development jumbos, high capacity trucks and loader guidance systems were implemented by contractors to stay ahead of ‘the pack’. All of these are now common across the industry.The demands of regular participation in competitive tendering coupled with aggressive fleet depreciation, means contractors tend to have more communication and opportunities to work with equipment suppliers than mine owners. Therefore, they are more likely to influence equipment design and product directions. They also have a unique opportunity to assist in trialling new concepts and technologies across a wide variety of operating conditions rather than being restricted to one mine.In addition, as a ‘guest’ on a mine site, mining contractors do not have the luxury of creating the environment for their preferred systems, rather they must have the capacity to adapt their technology to suit the offered environment at a particular mine. This leads to a pursuit of adaptive technologies that can be implemented selectively and seamlessly without excessive disturbance rather than ‘all-of-mine’ systems. These incremental innovations then become available for use across the mining industry where they can add value as ‘bolt-on systems’ to existing operations.Mining contractors, therefore, act as the bellwether for industry practices and equipment. However, in order to maintain their position they must engage industry stakeholders to deliver practical, innovative and cost-effective technologies that add value and result in an improved bottom line for all. This paper uses case study material to illustrate how the Byrnecut Group has approached innovation and how the theory of Disruptive Technology applies to underground mining innovation.CITATION:Kilkenny, D, 2017. Innovation in mining – a contractor’s role, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 59–68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By C Garlick, O Gregory, H Rogers, B I. Winters, Z C. Ye

BHP New Zealand Steel produces iron from titaniferous ironsand by a direct reduction process comprising multihearth furnaces/rotary kilns/electric iron melters. The electric iron melter is a six-in-line rectangular submerged-arc furnace which takes the partially reduced ironsand (80 per cent metallisation) from the rotary kiln and completes the reduction process to produce iron of nominally three per cent carbon. As the melter operates at around 1500¦C and under very hostile conditions, it is near-impossible to obtain any basic operating parameters such as the velocity and temperature distribution in the slag and in the molten iron. As a first attempt to understand the operating conditions inside the melter, a scaled room-temperature model using wax and water to represent the slag and iron, was constructed. This paper will report on some of the preliminary model results on the temperature distribution.

Jan 1, 1995