Search Documents

By H Wen

LongWangGou coalmine auxiliary inclined shaft heading face has a large section, fast heading speed, and large dust production. The problems of high concentration and wide distribution of dust in the roadway air are very prominent. To improve the efficiency of roadway ventilation and dustremoval, long-compression and short-suction (after this referred to as LCSS) are adopted. The dust concentration and airflow field distribution in the roadway are numerically simulated by FLUENT. The change of the position between the pressure duct and the exhaust duct and the different pressure-extraction ratios affect the distribution of airflow velocity, the formation of vortex zone, and the distribution of dust concentration in the roadway. When Ly = 25 m, Lc = 5.0 m, W = 1.2, a wind curtain is formed at 5 m in front of the heading face to prevent dust from spreading deeper into the roadway.

Oct 12, 2022

By D J. Bradshaw, E M. Wightman, C L. Evans, B Triffett

During the commissioning phase of Prominent Hill, periods of reduced recovery were experienced with higher-grade ore blends. This was unexpected and as part of the process to identify the cause, surveys were conducted in May 2009, with two different ore blends (copper grades: 1.94 per cent Cu (blend 1) and 2.49 per cent Cu (blend 2)). Metallurgical performance was assessed in terms of rougher recovery and grade with consideration of both pulp and froth effects. In addition, hydrodynamic measurements (gas hold up, bubble size, superficial gas velocity) as well as measurements of bubble load and top-of-froth grade were taken during the surveys and full mineralogical assessment of selected streams completed to characterise the nature of the differences. The metallurgical results showed that the lower performance was obtained with blend 2 which contained the higher amount of chalcocite and was higher-grade. Analysis of the survey data showed that for both ore blends more than half of the copper loss occurred in the +38 ¦m size fractions. Almost 30 per cent of the copper in the +38 ¦m fractions that reported to the rougher tails during processing of blend 2 was liberated compared to less than five per cent for blend 1. Additionally almost 60 per cent of the copper in the +38 ¦m fraction of blend 2 was chalcocite compared with approximately 20 per cent in blend 1. This paper discusses the sensitivity of the chalcocite-to-surface chemistry effects causing marked reductions in recovery either through reduced pulp recovery or froth phase (detachment) effects. The reagent suite and operating conditions were subsequently changed and the recoveries increased substantially and the sensitivity to ore changes eliminated. It should be noted that subsequent optimisation work, which focused on recovery improvement, has led to copper recoveries of over 90 per cent being achieved.CITATION:Bradshaw, D J, Wightman, E M, Evans, C L and Triffett, B, 2012. Characterising the reasons for the difference in performance of two ore blends in early processing at OZ Minerals Prominent Hill Operation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 273-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

Recovery of Rhenium from Mineral Raw Materials of Kazakhstan

Sep 13, 2010

By Rozycki J

The results of shaft lining monitoring gave rise to an investigation of cracks observed in the structure. An hypothesis was made that the cracks might be due to stresses caused by energy wave propagation, triggered during blasting or by the rock falls. However, it could not be excluded that the cracks had their origin in the rheologic changes taking place in the concrete. To prove the hypothesis, an investigation of the scale of the increase of stress due to the energy triggered was undertaken. At the same time it was decided to attempt to determine the "damage threshold" for such material in the danger zone. In the paper the investigation and its results are presented, as conducted in one of the shafts. In conclusion, certain generaliza- tions are proposed to give a starting point in the consideration of similar problems elsewhere.

Jan 1, 1987

By I Sherrell, R Jain

Worldwide iron ore feed grades are trending downwards and will continue to do so with the increasing difficulties of upgrading ores. This has led to operations looking for ways to capture current tailings that still contain valuable material. In the past, these were acceptable to dispose of, but this practice is no longer economically feasible. With the increasing trend of re-mining previous tailings deposits that could be decades old, new equipment designs have been introduced to upgrade current or historic beneficiation plants. These designs can effectively upgrade these tailings to saleable products.Outotec conducted test programs for upgrading iron ore tailings from flotation rejects, thickener underflow or tailings dumps on samples provided by customers around the globe. The studies utilised Outotec’s SLon vertically pulsating high-gradient magnetic separator in combination with preprocessing equipment such as low-intensity magnetic separation, screen or scrubber and flotation for downstream processing of the magnetic concentrate. A review of the equipment required to economically process these tailings is provided, along with testing data and industrial implementation examples. The effect of different operational and design parameters on Fe grade and recovery from processing each tailings sample has been highlighted.CITATION:Jain, R and Sherrell, I, 2015. Iron ore tailings reprocessing to maximise ore production, in Proceedings Iron Ore 2015, pp 149–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By B Liu, W J. Zhang, S Saydam, B Li

Rock bolts are commonly used to reinforce ground in underground mining and civil tunnel environments. Rock bolts serve two main functions: i) they suspend large, loose blocks of ground, and ii) provide a protective pressure arch to restrain the deformation in an excavated void. Automated and precise tracking of rock bolt positions can assist with the operational success of ground support by reducing the amount of labour required in current manual practices. A point cloud is a large list of x, y and z coordinates in three-dimensional space, that when visualised, show a precise 3D representation of a physical environment. Point cloud data can be collected using accurate LiDAR scanners. These scanners can be mounted on a stationary tripod or on a moving vehicle. A key way point cloud data is used is in the bolt detection project being completed in conjunction with UNSW Sydney, which aims to provide an automated location of underground rock bolts from LiDAR scans. The immediate challenge with identifying rock bolts is that they constitute a very small portion of the data set amounting to approximately 0.01 per cent of some of the collected civil tunnel data. The process of detecting rock bolts from point clouds therefore requires a quick elimination of large background data while still preserving the bolt data. A further challenge is that the geometry of underground environments can often be very complex and non-uniform. To overcome these challenges, a two-step coarse to fine deep learning approach is taken. The first step is a coarse background elimination step aimed at removing as much of the background data as possible. The second step is a finer classification method, which uses deep learning to further segment the bolts from the remaining background. Additionally, a computer vision module is being implemented, which is expected to increase the detection rate by adding another dimension to the training data set.

Nov 29, 2022

By R C. Schodde

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Over the last decade (2005–2014), a total of 439 significant deposits of gold and base metals were found in the world. Twenty (or 4.6 per cent) of these deposits were in the Pacific/South-East Asia (Pacific/SE Asia) region. In terms of contained metal, the region accounted for 1.6 per cent of gold and 13.8 per cent of copper found in the world. With regard to nickel and zinc/lead, the region’s contributions were insignificant.Over the same period, the Pacific/SE Asia region accounted for 6.6 per cent and 12.6 per cent of all gold and copper exploration expenditures in the world respectively. After adjusting for by-product credits, unreported discoveries and likely growth in resource, the unit discovery cost for the region was US$199/oz (compared to a world average of US$50/oz). For comparison, the unit discovery costs for the previous decade were US$55/oz and US$25/oz respectively. The region’s unit discovery cost for copper was US$0.036/lb (versus a world average of US$0.040). For comparison, the unit discovery costs for the previous decade were US$0.026/lb and US$0.008/lb Cu respectively.The region’s mediocre discovery performance doesn’t reflect its distribution of known mineralisation. Some countries within the region have a very good endowment per square kilometre.It is noted that the intensity of exploration (and resulting success) would be boosted if governments provided a more mining- and investment-friendly business environment and generated better precompetitive geological data sets (to identify new exploration targets and boost the country’s perceived mineral prospectivity). A multivariable regression analysis of a decade of data from the Fraser Institute’s mining company surveys found that a ten point increase in the Policy Perception Index or a 0.1 point increase in the Mineral Potential Index could boost (in the short term) exploration expenditures by 1.9 per cent and 2.7 per cent respectively. The resulting economic benefits of an expanded mining sector would be significant. The same story applies elsewhere in the world.CITATION:Schodde, R C, 2015. Discovery performance for gold and base metals in the Pacific/South-East Asia – 2005–2014, in Proceedings PACRIM 2015 Congress, pp 25–34 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By B Tessier

Checking the quality of a blast may be considered as subjective. Checking this quality will require measuring objective parameters. One of them is the resulting fragmentation of the blasted product. Numerous fragmentation æmeasuringÆ systems have been developed and marketed, based on image-processing. This presentation of FragScan will illustrate advantages and difficulties when using such a system. FragScan is essentially defending a policy of large and representative sampling. The purpose is to show how fragmentation is discriminating both productivity and profit of quarry operations on a blast-by blast basis. The next step will then be to ædriveÆ the blasting process to reach a æbetterÆ fragmentation. Other applications require the fragmentation as an essential result: this is the case for large boulders used in structure-reinforcement. Several case-studies have shown that FragScan can be used for quality-control, checking size-distribution of the product according to the requirements of the end-user. Only clear thinking about the precise use of such a æmeasurementÆ will further the success of this task.

Jan 1, 2001

By Lawrence PR, Hoffman W

The dissolution of gold from various ore-bodies is discussed in terms of extraction rates and reagent consumptions during leaching. Gold dissolves slowly in cyanide but reagent consumptions are usually satisfactory. In almost all cases where excessive cyanide consumptions occur, similar high consumptions result with other lixiviants. Recovery of gold from cyanide solution is well established and comparatively simple technology.Gold dissolution in thiourea is faster than cyanide but significant consumptions of thiourea, due to both adsorption and oxidation, occur. Gold recovery from thiourea solutions is likely to be more difficult than from cyanide.Chlorination of gold is very fast in acidic conditions but excessive consumption of chlorine occurs for ores containing greater than 0.5% S. Reprecipitation of gold and handling of acidic chlorine solutions are both significant problems. The mechanism of gold reduction onto activated carbon creates difficulties in the carbon in pulp process for recovery of gold but means a simplification in the production of bullion from loaded carbon.

Jan 1, 1984

By Golubkov OL, Fedotov PB, Shkylar FR

One of the fundamental parameters of the race- way is its extent (a{ o), which has a significant effect on the distribution of gas and material flows in the lower region of the furnace. pp The known relationships for determination of aC o in most cases link the length of the raceway with the parameters of the blast, while the para- meters of the coke layer, in which the raceway is formed, are either ignored or else expressed in terms which are difficult to determine experimen- tally. Furthermore, the coke combustion propert- ies are not always taken into account in current blast furnace operating practice with combined blast. A complex dimensionless parameter, which re- flects the properties of the interacting media, is the ratio of the kinetic energy of the hot, com- bined gas stream to the potential energy of the coke flow, burning at the tuyere in a gas of known composition. Statistical processing of experimental data on the extent of the raceway zone, obtained from literature and our own work on operational furnac- es, has led to a working formula of the following Form:

Jan 1, 1981

By B Jones, M Chappell

Installing ground support correctly is not an easy task, whether lack of operator training, poor ground conditions or underperforming equipment. Confirming the quality of installation can help with planning and remedial works and help to maintain a safe working environment. A 2?m bolt with 700?mm of encapsulation will pass a 10?t pull test (assuming ground conditions permit); however, it will not provide any data of the unencapsulated length and thus the ability to withstand corrosion. Complimentary testing in the form of non-destructive testing (NDT) can provide factual data that leads to the assessment of the quality of the encapsulation. By improving the quality of the encapsulation, the risk of corrosion is reduced, the ground support durability is improved and hence the asset life is enhanced.This paper presents a case study of a trial using the NDT system RokTel™. Installations of varying quality were installed and tested. The characteristics tested were corrosion, load and free length. These characteristics can be tested and assessed for cable bolts, thread bar bolts and split sets. The aim of this paper is to present NDT testing as a viable method for assessing installation quality and ongoing performance of the ground support.CITATION:Jones, B and Chappell, M, 2014. A non-destructive testing method for measuring bolt condition, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By M O. Tade, M W. Sze

The particle dynamics of a mixture of coal and zircon system wasstudied in a scaled-down cold model of an industrial kiln. Thefactors investigated in the study were rotational speed (N),zircon-to-coal feed ratio (B), coal particle size (dpc) and the angle of inclination (*) of the kiln. The technique used is the residence time distribution (RTD) method. It was found that rotational speed and angle of inclination are important parameters that affect the residence time of particles in the kiln. A mathematical model for predicting the mean residence time of particles in the rotary kiln was developed. Comparisons with reported models for such systems are discussed.

Jan 1, 1998

Temperature Sensitive Polymers as Efficient and Selective Flotation Collectors

Sep 13, 2010

By B Besa

Australia is a world leader in the design and operation of mines accessed by the decline method. Literature indicates that a number of metalliferous underground mines using the decline system are also increasing steadily. This increase has generated a great deal of interest in underground haulage systems in future due to the huge costs involved in the development of declines. Studies have also shown that the current method of accessing orebodies by the conventional decline method has proved to be expensive, especially for narrow vein deposits. This is because decline development costs are influenced by mine planning and design parameters as well as available haulage systems that the mining engineer can choose from. The current access method suggests that more waste material is being extracted because of the size of decline openings adopted (5.5 mW and 5.5 mH). Also the conventional 1:7 decline gradient and turning radius of 20 m makes decline lengths, as well as the duration of development, excessively longer. This paper discusses results of a mine design case study with monorail technology as a method of accessing and developing the decline. The proposed system is economical, has high advance rates and offers a significant reduction in capital expenditure. The study compares costs, development metres and the duration of decline development using the monorail system with the conventional (truck haulage) access method. Results obtained indicate that the monorail technology has the potential to reduce the decline length by over 62.6 per cent and decline costs by 63 per cent for the case study. The monorail system also reduces the total capital development costs by 22 per cent for the same case study. Due to rapid development resulting from increased advance rates and the shorter decline length coupled with smaller decline openings, the time to access the deposit reduced by 71.8 per cent. This case study demonstrates that the economics of narrow vein deposits can be improved significantly by using the monorail system of decline development.

Jan 1, 2008

By Quast K. B

The effects of metal ion addition rates and contact time on the activation of synthetic sphalerite using copper, cadmium and silver ions were determined in order to investigate the exchange characteristics at the mineral surface. The stoichiometry of the adsorption indicated that the activation of sphalerite involved both a simple ion exchange and redox process in which the activating ion and oxygen were reduced, and the mixed-sulphide surface was oxidised to produce elemental sulphur and a metal-deficient sulphide surface. Unactivated sphalerite was shown to be relatively hydrophilic, with recoveries usually less than 20 per cent for a five-minute float. Activated sphalerite could be readily floated without the use of a conventional collector. This inherent flotability of the activated sphalerite had previously been associated with the formation of a metal-deficient sulphide layer; however, this study emphasizses the significance of the surface oxidation processes occurring.

Jan 1, 1993

A new national-scale geochemical survey is under way inAustralia with the aim to provide energy and mineral explorers with state-of-the-art precompetitive data and information about the continentÆs potential resources. This low-density geochemical survey will provide a national geochemical data layer using consistent sampling medium and sampling, preparation and analytical methods. Large-scale geochemical patterns thus revealed are expected to point to new areas of exploration potential. The project is funded under the Onshore Energy Security Program. It is hoped that this new national geoscience dataset will help make Australia a more attractive destination for energy and mineral exploration investments. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By G Capes

A novel open stope design approach is presented that delivered improved performance in a mining area with poor ground conditions at the Olympic Dam mine. During 2019, a large open stope had an unplanned caving event resulting in the inability to extract the planned tonnes and subsequent sterilisation of nearby stopes. A design limitation was the lack of data and understanding around the alteration domain extents, the rock mass strength controls and limits, the failure modes controlling stope stability in the local area, and the use of conventional stope shapes. From the available data and failure observations, it was inferred that the dominant caving failure mode resulted from a blocky rock mass impacted by structure and alteration causing an unravelling failure mechanism. Numerical and empirical analyses were conducted to test this hypothesis and establish strength limits for design. The strength limits for the design were then used to provide a range of outcomes from which future stope design shapes such as chamfered backs could be selected. Three alternate chamfered geometries were selected to trial the innovative designs. The application of this methodology in 2020 resulted in overbreak reduction from >100 per cent in the initial caved stope to

Mar 29, 2023

Recycling of Sludge from the Production of Manganese

Sep 13, 2010

Since early-2001, Kalgoorlie Consolidated Gold Mines (KCGM) has successfully operated an ultra fine grinding (UFG) circuit to supplement its roaster capacity for the treatment of the refractory gold flotation concentrate. A second UFG mill was installed in 2002 taking the total UFG capacity to over 20 tph while grinding to 11 to 12 microns and achieving over 90 per cent gold recovery. A development program in 2002/3 involving plant trials, pilot plants and laboratory testwork resulted in process improvements and a better understanding of the milling and gold leach processes that assisted in narrowing the gap between UFG and roasting. This paper details the operation of the ultra fine grinding process at KCGM as a non oxidative treatment for the extraction of gold from a refractory ores.

Jan 1, 2003

By M W. A Asad, E Topal, D S. S Sandanayake

Underground mine planning requires an optimal stope layout as a prerequisite for the definition of an optimal production schedule. The procedure to generate an optimal stope layout considers an orebody model and economic parameters as inputs. It evaluates all possible combinations of mining blocks and creates a set of stopes by satisfying the physical mining and geotechnical constraints. Thus, the procedure is computationally complex, and generating a solution to the problem is a challenge. This paper presents an implementation of a new heuristic algorithm that solves the stope layout problem. In two case studies, the algorithm achieves 11.2 per cent and 22.5 per cent superior solutions to the industrially available maximum value neighbourhood approach.CITATION:Sandanayake, D S S, Topal, E and Asad, M W A, 2014. Implementing a new heuristic approach to the underground mine stope layout problem, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 243–248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014