Search Documents

By R Dimitrakopoulos, C Paduraru

The optimisation of mine complexes and related value chains is a challenging problem due to the simultaneous presence of a highly-dimensional decision space, integer decision variables, non-linear constraints and recovery functions, as well as geological and market uncertainty. In addition, if the uncertainty is revealed progressively, then decisions need to continuously adapt to new information, which poses additional challenges. Stochastic dynamic programming is a well-known class of methods for addressing problems where a decision-maker reacts to new information. While simplistic applications of dynamic programming using exact representations would be intractable for any realistic mine planning problem, new dynamic programming methods using approximate value function representations have been successfully implemented in the past to address problems of similar complexity. This work formulates the problem of mine complex optimisation as an approximate dynamic program and presents an application of the resulting method to a gold-copper deposit.CITATION:Paduraru, C and Dimitrakopoulos, R, 2014. Mineral supply chain optimisation under uncertainty using approximate dynamic programming, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 415–422 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Sen S. K, Banerjee D. D, Nandy D. K

It has been stressed that the intrinsic spon- taneous heating characteristics of a coal is not enough in predicting spontaneous fire risk of a mine. The influence of extraneous conditions created from the system of mining operations are also to be reckoned with, A case study was made with a mine in Jharia field, India, being proposed to be developed under short wall method with complete extraction in 4-5 slices followed by stowing.

Jan 1, 1988

By C Rizos, A Ng

Land surface deformation can be caused by underground mining activities. The maximum subsidence normally occurs directly above the location of the excavation of the coal seam. In the case where the longwall mining technique is applied, the magnitude and shape of the subsidence bowl are constrained by the longwall structure (pillar). This paper describes the use of satellite radar interferometry for monitoring surface subsidence due to underground mining, as a cost-effective geodetic technique and complementary to conventional ground surveying techniques. This paper uses data acquired by the current generation of SAR satellites û the European ENVISAT and the Japanese ALOS û to monitor ground subsidence in the southern highland coalfield in New South Wales, Australia. An accumulated DInSAR subsidence mine map is produced using six successive ALOS acquisitions. The results are post-analysed with the aid of geographic information systems (GIS) and validated using ground survey data.

Jan 1, 2008

Incidental to the progress of a geological survey of the Kalgoorlie goldfield during 1927 - 1928 a number of specimens of telluride minerals were obtained, chiefly with the help of Mr F G Brinsden, general manager of the South Kalgoorlie mine, and Mr Ernest Williams, general manager of the Boulder Perseverance mine. This collection was supplemented by a number of small specimens, including the rare copper telluride, which were collected and preserved from the Kalgoorlie mine by Mr A E Paton, and also by a few miscellaneous specimens from the collection of MrS F C Cook, of the Palace Hotel, Kalgoorlie.An extensive knowledge of the rare tellurium-bearing minerals was compiled during the last century from occurrences in Transylvania and Colorado. The recognition of different species has been based on chemical analyses and crystallographic measurements. In a few species there has been an absence of crystalline form, and these, together with the discoveries in this century of rickardite and 'weissite', muthmannite and empressite, have depended chiefly on the chemical analysis for identification. On the other hand, the crystalline form of nagyagite and stiitzite has been described in detail, while their precise chemical formulae were doubtfully defined.The announcement of the occurrence of tellurides at Kalgoorlie by A G Holroyd in the Kalgoorlie Mine on 29 May 1896, followed by their discovery in comparative abundance, stimulated the further study of these minerals. In this locality there is a general absence of well-formed crystals, and the knowledge gained has been confined to the record and description of previously known, but exceedingly rare, species.No new species has been recorded, but the intimate association of various species resulted in early description of two supposedly new species, kalgoorlite and coolgardite. These have been discredited since the investigation by L J Spencer in 1903, based on a collection of specimens donated to the British Museum.Spencer's list of species at Kalgoorlie comprises calaverite, sylvanite (or krennnerite), petzite, coloradoite, 'and altaite, and does not include hessite, previously mentioned by Krusch. In 1912 melonite and a copper telluride were added by J A Thomson and the presence of hessite confirmed. In 1912 there also appeared a full and detailed account by E S Simpson on behalf of the WA Geological Survey, which embraced his earlier notes on the tellurides, and which represents the state of our knowledge of the Kalgoorlie minerals, practically as far as can be attained without the use of the reflecting microscope.The position has been stationary for about 18 years, and it was thought. that the best use to which the present collection of tellurides could be devoted was an attempt by mineragraphic methods to study the mineral relationships, not only of the tellurides among themselves, but also to gold and other associated minerals. The precise mineral content and relationships become a factor of added importance with the development of flotation methods of treatment at Kalgoorlie.Moreover, the study would supplement the description of the ore deposits of the Boulder Belt that has recently been published.

Jan 1, 1994

By Tack K

During its 28-year life the MHD ISP smelter has gone through two phases, each of about a dozen years. The first phase was a learning one; in the second phase the lessons were applied and throughput and production rose strongly. Early experience revealed the robustness and the flexibility of the Imperial Smelting Process. The experience was demonstrated by strong increases in the throughput of mixed lead-zinc concentrates and of secondary (oxide) zinc materials. Purchased material quantities rose from 175 000 tonnes/year to 200 000. The required capacity increase of the IS furnace to smelt the higher throughput was achieved by relatively minor modifications; for instance a change to the internal furnace profile gained an extra two square metres in cross sectional area. The furnace hearth area has remained practically unchanged over its entire history. The paper concludes that there is still more potential to be drawn from the process and MHD intends to sustain raw material input at a new level of 240 000 tonnes/year. However, this rate will have to be achieved under the imposition of more stringent environmental and product quality standards than ever before.

Jan 1, 1993

Any future developer of underground mining on the Bendigo goldfield will need to understand the unique geology and gold occurrence of this field. The development and sloping system employed will be primarily designed around these unique features. Modern techniques and equipment used in narrow vein mining will be applicable in this situation.The purpose of this paper is to examine the important geological features of the field as well as the known historical occurrences of the type of gold deposition in the ore bodies. This information will point to a system of development and extraction which will accommodate these features.

Jan 1, 1993

The Yabulu refinery of Queensland Nickel Pty Lld near Townsville now imports more than three million wet tonnes per year of nickel laterite ore from New Caledonia and Indonesia, making it the largest importer of any commodity in Australia. The project has illustrated that importing untreated bulk ore and re-exporting high value products makes good economic sense for the company and the nation.The economics of this exercise were considerably enhanced in 1994 by changing the project's principal product from nickel-oxide sinter to refined high-purity nickel metal. It is one of the few operations in the world where nickel ore is transformed to nickel metal at a single site.Several novel technological processes were developed at Yabulu and incorporated into the refinery to allow this product transition to occur. By utilising internally developed technology the new processes were installed at a capital cost of less than $10 million. It is unique for a large nickel producer to change completely the quality of its entire product range many years after the plant was constructed and considerable attention to marketing the new products has been required.The changes have meant that the project is no longer limited to selling lower-value oxide sinter to a relatively small number of large stainless steel mills. In the past year sales of the new high purity nickel metal products have expanded to include a broad range of international customers in the special alloy, foundry and chemical industries.

Jan 1, 1995

The energy input requirement to produce the molten slag associated with iron production to the modern Australian blast furnace, is estimated to be 2.OMJ/kg. In converting blast furnace slag to products of higher commercial value, advantage should be taken of this energy content by transporting molten slag from the furnace for beneficiation and processing in the molten state at an "off furnace site". The refined slag melt may then be converted into a variety of products for use in the building and construction industries, e.g. slag cement, slag sand and slag aggregates, insulation wool and various slag ceramic products. Some results of studies into slag melt beneficiation and conversion processes involving both molten and cold granular slag raw material, are presented.

Jan 1, 1979

By X Yang, T Zhang, Z Li, Z Yan, M A. Williams, S Qin, P Wilson

Continuous development of complex new steel grades to meet the ever-increasing demand of high performance causes recurrent issues in steel continuous casting such as surface quality defects (eg cracks, depressions, deep oscillation marks) and productivity challenges (eg faster casting, near-net shape casting). Continuous casting of steel is a highly successful metallurgical process. Much of this success can be attributed to the performance of the casting powder that is added to the top of the mould, creates a liquid slag pool as it is heated, and forms a slag film between the watercooled copper mould and steel shell during its passage down the mould. Mould powder selection is a compromise between the conflicting requirements of heat transfer and lubrication. In an EU RFCS (Research Fund for Coal and Steel)-funded project, various techniques are developed to offer the opportunity to adapt the slag film to meet the conflicting needs in different parts of the mould such that mild cooling can be generated in the meniscus, mid-broad face or corner areas whilst maintaining lubrication and offering higher cooling rates in other areas of mould. This has significant potential to address the industrial issues in product quality and productivity of continuous casting. This paper reports, as part of the EU RFCS project, the determination of crystallinity and porosity in slag films for casting challenging and innovative steel grades using new methods. In comparison with the methods such as X-ray powder diffraction (XRD) analysis and optical microscopy / scanning electron microscopy (OM/SEM) analysis that are currently adopted by the industries, EBSD (electron backscatter diffraction) has been employed to determine the crystallinity of the slag films taken from industry casters. X-ray computed tomography (XCT) plus 3D image reconstruction has been used to determine the slag film % porosity with pore volume, pore size distribution, and pore location, which can be linked with the performance of the slag films during casting different steel grades.

Jun 19, 2024

By S Latchireddi

Close circuiting autogenous and semi-autogenous mills is an energy efficient way of grinding and a number of operations have utilised this in the design of their comminution circuits. Owing to the large flow of slurry through the mill that results from operating this way the grates and pulp lifters have to be designed to cope. However, the literature has little or no information on how grate and pulp lifter size and design are related to their ability to remove slurry from the mill. Over the last few years the JKMRC has been researching this area and has developed relationships between grate/pulp lifter design and flowrate capacity. At the same time it has determined the major causes of pulp lifter inefficiency and a solution to preventing this inefficiency (the Twin Chamber Pulp Lifter). This paper describes the models that have been developed through this program and uses industrial scale data to illustrate their accuracy. Results from the industrial trials of the Twin Chamber Pulp Lifter are also presented.

Jan 1, 2000

By E Kabwe, M Karakus

Deep hard rock underground mines tend to experience high stress as such drives exhibit dynamic responses attributed to a rock burst variant (strainburst). This dynamic behaviour is difficult to predict, and every effort is made to devise the appropriate dynamic support system for its associated failure restraint. This paper outlines the back analysis and the support scheme design for an underground decline that exhibited damage from a dynamic strainburst occurrence. It employs a decline section that experienced a dynamically loaded strainburst that initiated rock fragment ejections. The procedure involves a preliminary structural analysis, a seismic intensity measure, and a rock mass simulation to determine the static stress concentration and ground support system response. The numerical simulation is conducted in FLAC3D which employs the advanced strain-softening IMASS constitutive model governed by two Hoek–Brown (HB) bounding yield surfaces. To account for the post-peak brittleness response associated with strainburst the plastic strain multiplier () is adjusted to 0.0 < < 1.0. The back-analysis shows that the occurrence was initiated by a low-intensity seismic wave that superimposed an extra stress component to the initial static stress which triggered rock fragment ejections. Additionally, the appropriate support scheme comprised of Weldmesh, Fibrecrete, static (split set) and yieldable (Kinloc) reinforcements is recommended and implemented. Thereafter, the bolt’s efficiency is evaluated based on the axial force and elongation capacities and then compared with the published bolt performance data. The evaluation results show that the maximum bolt axial force (0.1 per cent) and elongation (0.006 per cent) are below the designed capacity and rupture strain.

Nov 29, 2022

By H S. Shin, H Jin, B H. Ryu, J Lee

Prospecting ice on the Moon necessitates drilling systems to obtain subsurface samples and measure the composition of ice deposits. Landers and rovers equipped with drilling equipment are essential for analysing ice and subsurface resources located at the Moon’s poles. These devices must be small, lightweight, low-power, highly efficient, and high-performance units to function properly in the extreme conditions of the lunar environment. Researchers have developed a prototype drilling apparatus capable of operating in atmospheric and cold environments. A newly developed drilling system in Korea, capable of performing not only sampling but also subsurface investigation, is introduced.

Sep 1, 2024

In contrast with mining in areas close to the main centres, mining in remote areas is characterised by comparatively high initial investment and relatively high running cost for the life of the mine. This is because of:the real cost of establishing and running the operation at a location distant from the necessary infrastructure; and the perceived risks priced into their costs by the multitude of suppliers involved in the project. Optimal co-operation between the mine and the supplier in developing the right rela tionship and the correct technical solution permit both cost elements to be reduced. This re duction may well mean the difference between success and failure. This paper examines the possibilities for optimising the contribution of the equipment supplier to the overall success of the process. Issues covered include the necessity to provide more than merely equipment fit for the purpose , but also the need to maximise the benefits of equipment ownership over the life of the mine. A simple method of determining the optimum timing for equipment replacement or rebuilding is proposed . Furthermore the maintenance contract (or performance agreement) is suggested as a means of leveraging the supplierÆs commitment to the mining operation. The specific examples are based on experience with mobile equipment but the methodology has relevance to other equipment and supplies.

Jan 1, 1998

The Queensland Department of Mines believes it is in the best interests of the gold mining industry to reduce and control the environmental impacts from gold mining since that is the community expectation.The Department of Mines has set as a special condition of many recently granted Mining Leases the requirement to submit a "Description of Operations" for the approval of the Minister, prior to commencing initial mining operations. In order to facilitate compliance by lessees with this condition an explanation is given of the reasons for this condition and how it is intended to achieve the objective of environmental protection.Environmental impact is operations dependent. Impact on a lease will vary quite significantly with the scale and methods employed. Before a lease can be granted and mined it is therefore necessary to have this information. The parameters of operations most critical both in terms of environment impact and economic viability are worked out and agreed with the lessee before the lease is granted. An approved description of operations which is required now, prior to the start of mining, provides the details of that agreement for the security and benefit of the lessee and the inspectors. It also provides the details of operations and environmental controls which were not required prior to the grant of the lease but are nevertheless required and necessary for compliance with the environmental standards.

Jan 1, 1986

Mine geologists have access to an economic mineral deposit, production parameters and secure exploitation title. They are well placed to understand ore formation and should contribute to the effective exploration of company mine property. Application of their special skills has been curbed by pre-occupation with production duties and by company re-engineering, including staff reductions. Contributions to exploration have been diminished and personal development inhibited. Modified management is required. Participation in mineral system studies and in exploration research comprise part of the basis for the re-emergence of mine geologists on the exploration scene. Changes in investment strategies in the minerals industry may create new employment opportunities. With regard to estimation of resources and reserves, the competence of practitioners who are incapable of disclosing their methods in transparent terms is under question. Ethical standards are also under public scrutiny because of some notable malpractice. Independent auditing may hecome more intrusive. While understandable in a market context, it reflects poorly on the profession. More substantial effort in public communications can improve the credihility ofthe industry and equip practising mine ceolouists for snider responsihility.

Jan 1, 1997

The development of present methods of pillar extraction has evolved from the very earliest of hand mining operations which were limited in scope by venti- lation and transport considerations. Conservation and safety considerations also have led to the current shortwall operations with conventional equipment and powered supports. The shortwall methods have had significant effects on safety, costs, con- servation, flexibility, and other aspects of pillar extraction. The present stage falls short of the ideal but is some guide to prediction in what direction may lie the ideal methods for the future.

Jan 1, 1974

By E Thomas, L McCallum, G Dale, J Bennett, K Reardon-Smith, S Raine

Sustainable closure of coal mines in Australia to a safe, stable, non-polluting condition remains one of the industry’s biggest environmental and social challenges. A significant proportion of mines in the Bowen Basin of Queensland have dispersive spoil. Based on an estimated area of 20,000ha and a rehabilitation cost of AUD$100,000 to AUD$150,000/ha, the instantaneous rehabilitation liability for the Bowen Basin alone is estimated at AUD$2 to $3 billion.Dispersive spoils present problems in post-mining rehabilitated landforms due to increased potential for surface and tunnel erosion, compromising the ability to achieve fundamental mine closure objectives of a safe, stable, non-polluting and self-sustaining post-mining landform (Minserve, 2004). Dispersion results in clay particles being mobilised and transported in water, even at low flow velocities (So et al., 1998; Minserve, 2004), and blocking of soil pores, resulting in surface sealing, crusting and reduced permeability (DNR, 1997; Vacher et al., 2004) which, in turn, further increases runoff (Dang et al., 2018).CITATION:Dale, G, Reardon-Smith, K, Thomas, E, Bennett, J, McCallum, L and Raine, S, 2018. A process-based approach to mine rehabilitation decision making using Bayesian modelling and risk-based principles for dispersive spoil rehabilitation, in Proceedings Life-of-Mine 2018, pp 106–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Leahy G. J, Moxon N. T, Nicol S. K

Experimental work is described in which extremely dilute aurocyanide liquors are treated with novel surface-active complexing agents to produce a hydrophobic aurocyanide species. Subsequent aeration of these liquors causes accumulation of such species at the air-water interface and the aurocyanide complex is transferred to a froth concentrate. A detailed performance assessment of this process is made and this knowledge used in the design of a pilot plant facility. Early results indicate the feasibility of the selective recovery of aurocyanide ions from reclaimed residue dam water (approximately 0.2ppm Au) with upgrade ratios of the order 180:1. A further study was made applying ion flotation to the recovery of gold from a carbon-in-pulp (CIL) feed liquor (approximately 1.0ppm Au). The probable economics of this process compared to conventional CIL processing is also described. Successful development of countercurrent ion flotation for concentrating solids-free gold solutions may offer a lower cost alternative to existing gold ore processing technologies, or in more secondary applications such as concentrating dilute gold solutions or heap leach runoff. The technology may also have more generalised applications to other heavy metal process- Ing.

Jan 1, 1991

By C Zhang, G Si, J Oh, X Zhu

The presence of rock joints has a huge impact on the strength, deformability, and permeability of fractured rock masses by providing surfaces of weakness on which further deformation are more prone to occur, and by serving as the major channels of water flow due to low matrix permeability. In earlier studies, water flow-through rock joints is often assumed as laminar flow between two ideal smooth parallel plates, and the well-known cubic law was derived and widely used to characterise the hydraulic behaviour of rock joints. However, natural rock fractures are irregular and of spatially varied aperture. Thus, the concept of equivalent hydraulic aperture was introduced to modify the cubic law. Numerous works have been conducted on the relation between hydraulic aperture and mechanical aperture incorporating various geometrical parameters. The surface roughness is one of the most sensitive factors for water flow-through rock joints. The aperture distributions are irregular in natural roughed fractures relative to the parallel plates. Barton et al (1985) and Olsson and Barton (2001) incorporated the joint roughness coefficient JRC in evaluating hydraulic aperture and proposed an empirical equation based on fluid flow tests. However, their equations do not conform to the dimensional consistency. Many other researchers (Zimmerman and Bodvarsson, 1996; Xiong et al, 2011; Li et al, 2019) considered aperture distributions in their equations. But the aperture distributions change during shear was always neglected. The contact of rock joints also has a significant impact on the hydro-mechanical behaviour of rock joint, since fluid tends to flow-through a rough joint along connected channels while bypassing the contact obstacles with tortuosity. Nonetheless, previous research mostly considered joint roughness or aperture changes based on 2D joint profiles, while the contact and tortuosity based on 3D surfaces were often overlooked. Only a few works have been made on quantifying the effect of contact area on flow behaviour (Walsh, 1981; Zimmerman et al, 1992; Zimmerman and Bodvarsson, 1996; Yeo, 2001), and mostly ignored contact area change induced by shearing and the associated impact on flow behaviour. Summarily, the quantification of fracture geometry effects on water flow in single rock joints still needs further investigation, especially when considering coupled shear-flow processes. This paper, therefore, aims to study the impacts of contact area and aperture distributions of the single rock joint on the flow behaviour. The evolutions of contact area and aperture distributions induced by shear are considered. Then, an improved model for estimating the hydraulic aperture with the mechanical aperture incorporating the above factors is developed. Finally, a series of shear and shear-flow tests are conducted on artificial joint samples and the model performance is verified by comparing against the results of experimental tests.

Nov 29, 2022

By S H. Begg

"*This is an abstract only*Most technical and economic analyses are performed to reduce uncertainty to help make decisions. Decision-making is about ranking alternatives - rarely are precise predictions required, if even possible. This simple observation has profound implications for modelling approaches, how they deal with uncertainty and the reliability of information provided by subject matter experts.CITATION:Begg, S H, 2013. Some reflections on uncertainty, decisions, models and people, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 3-6 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013