Search Documents

By G C. Lukey, J S. J van Deventer

The disposal and subsequent encapsulation of mine tailings in a cost-effective and environmentally secure and responsible manner is one of the principal issues facing any modern mining project. A careful assessment of all options available for the capping and subsequent remediation of tailings is important because it can result in large capital, operating and closure cost-savings. For these reasons, the technology of geopolymerisation is receiving increasing attention for the stabilisation and solidification of waste materials produced from mining operations. The first part of the current study investigates the application of geopolymer technology to the capping of hypersaline mine tailings. It has been found that suitable geopolymeric materials which have satisfactory compressive strength, durability as well as low permeability, can be formed using between 60 - 75 per cent of mine tailings as the main ingredient. It has been established that geopolymeric materials have the ability to suppress dust generation and prevent salt precipitation on the surface of the mine tailings. The slurry-like consistency of geopolymers would promote efficient application procedures through established tailings disposal techniques. This is a possible close-out technique for hypersaline tailings storage facilities such as those commonly found in Western Australia, which meets both regulatory requirements and community expectations. The immobilisation of contaminant metals within geopolymers has been investigated in the second part of the present study. In particular, the leaching characteristics of Cu and Pb from geopolymeric matrices derived from different fly ash sources have been examined. Potential breakdown of each geopolymer containing metal contaminants due to the leaching of Si and Al from the geopolymeric matrix has also been investigated.

Jan 1, 2000

By Wright G. A

The objective of refining in steelmaking is to reduce the concentration of impurity atoms, e.g. sulphur, phosphorus, from an initially high level to a specified low concentration. A two-film theory of refining is presented in which the rate of

Jan 1, 1980

By Whitehead A. B

INTRODUCTIONDuring the past few years there has been considerable interest in developing the so-called direct reduction processes for treating iron oxides. The various methods proposed were recently reviewed by Scortecci and Palazzi (1960).In particular the application of fluidized bed techniques received considerable attention and, on first examination, this seems to be the ideal method 'of dealing with fine iron oxides. Several difficulties (e.g. product agglomeration) require the method to be investigated further before its potentialities can be fully assessed.PROPOSED FLUIDIZED BED REDUCTION PROCESSESBrassert and De Jahn (1951) were among the earliest to suggest the use of fluidized beds for the reduction of iron ore to metallic iron. Their patent was followed by many others proposing similar concepts, mainly from Lewis (1955), Ogorzaly (19.56), Shipley (1956), Agarwal (1960'), Osborn (1958), Texaco Development Corporation (1956) and Stelling (1957).The H-iron process (Squires and J ohnson, 1957; Lubker and Bruland, 1960) is the only scheme that has been an economic success. This process, mentioned later, manufactures a 'premium quality product in the form of sized iron powder.AIM OF THE PRESENT WORKThe work reported here was performed to assist in the formulation of a comprehensive pl'ogramme of research into fluidized bed reduction processes to be undertaken at the...

Jan 1, 1962

By Gray N. B

The need to improve existing metallurgical processes and to develop new processes to meet the economic challenges that lie ahead requires the application of the tools of process analysis viz. mathematical models, physical models, pilot plants, laboratory measurements and plant tests. Examples of the application of these techniques to processes are described in this paper. Several of these techniques, combined with basic knowledge, are necessary to make improvements and for existing processes this always involves plant measurements. Also because metallurgical processes include extraction, refining, alloying, casting, mechanical working and heat treatment, an interdisciplinary approach to research and development is essential. This paper argues that metallurgical engineering is a discipline that is uniquely able to encompass the broad spectrum of chemical- and physical-metallurgy processes and is therefore essential to the health of the metallurgical industry.Regrettably many metallurgical engineering departments are not offering courses on process analysis, control, optimization, etc so necessary to meet modern industrial challenges.

Jan 1, 1985

By A D. Strand

The Coeur dÆAlene mining district in northern Idaho, USA is the second largest producer of silver in the world. The Proterozoic Revett Formation hosts most of the mesothermal Ag-Pb-Zn vein ore in the district; it consists of informally designated lower, middle, and upper members. All three members show up to an order of magnitude of southward thickening across the regionally significant Osburn fault. Changes in thickness of the Revett Formation across the Osburn fault reflect a major, down-to-the-south, crustal-scale fault that:was active during sedimentation, was periodically reactivated during the structural and metallogenic history of the district, and likely provided first-order control over regional fluid flow during mineralization events. Where vein structures intersect favourable strata, they produce rich ore; where vein structures cross unfavourable strata, they are poorly mineralised or barren. The most favourable host rock in the district is quartzite, which accounts for the large production from the quartzite-rich Revett Formation.The district has five main types of hydrothermal alteration:feldspar destruction, hydrothermal bleaching, carbonatisation, sulfidation, and silicification. Feldspar destruction is the most extensive and pervasive type of alteration, involving the district-wide absence of feldspar from Belt Supergroup rocks. Hydrothermal bleaching results from the destruction of hematite; it forms alteration envelopes that extend for tens to hundreds of metres into the wall rocks around many of the mineralised veins. Siderite alteration is most diagnostic of mineralisation, forming alteration envelopes that extend for tens to hundreds of metres into the wall rocks around all mineralised veins. Fine-grained arsenopyrite and/or fine-grained pyrite commonly form alteration zones adjacent to high-grade ore shoots that extend for metres to tens of metres into the wall rocks. Widespread silicification is most easily recognised by the presence of numerous quartz veins.

Jan 1, 2002

It is possible from simple gas behavioral theories to develop more complex relationships which allow prediction of transport phenomena such as diffusivity and viscosity of gas mixtures. Such physical data can be used in engineering calculations for both bulk gas movement and gaseous chemical species movement. Both of these are important in the solution of mines ventilation systems. There are specific limits of flammibili!'y of some common mines gases.

Jan 1, 1983

The Peko copper orebody is associated with a body of magnetite rock which it has partly replaced. The primary ore averages about 9 per cent. copper and 4 dwt. gold per ton and locally IS much richer. It consists essentially of chalcopyrite and unreplaced magnetite, with lesser amounts of pyrite, marcasite, pyrrhotite, cobaltite, bismuthinite, native bismuth and native gold. The earliest formed mineral is wolfram, and the latest formed is goethite, so that the temperature of deposition ranged from about 5000 C. to 1650 C. or lower.Oxidation extends to 270 ft., which is 100 ft. below the present water level. The oxidized ore consists of cuprite and native copper, and has replaced more or less massive chalcocite of a former zone of secondary sulphide enrichment. The present zone of secondary sulphide enrichment extends from about 270 ft. to 310 ft. depth.INTRODUCTIONThe Peko mine is about 6 miles south-west of Tennant Creek township in the Northern Territory, adjacent to a small outcrop of hematite rock that projects above an otherwise featureless "bull-dust" fiat.The copper-gold orebody being developed in this mine did not outcrop. It was first detected in 1950 by a surface diamond-drill hole (DDH.1), which intersected primary copper ore at a depth of 400 to 425 ft. This ore contained from 4 to 11 per cent. copper and 1 to 25 dwt. gold per ton. Since then a shaft has been sunk, and crosscuts and development drives have been opened on the 210..ft., 300-ft. and 400-ft. levels, which are also connected by winzes. Two diamond drill holes sunk from the 400-ft. level have intersected theorebody at about 450 to 460 ft., and a winze from the 400-ft. level intersected the lode from 445 to 500 ft. At this point it is 54 ft. wide, and averages 9 per cent. copper. More recently an inclined surface drill hole (Peko No. 1) has cut the lode at 856 ft. to 921 ft., equivalent to a vertical depth...

Jan 1, 1955

Most of the gold reef mined today in South Africa is approximately 1 m in width with slopes about 30 m long. To prevent production interruptions it is essential that the stopes should not be blasted in sections. The shortage of experienced labour and arduous working conditions at the face dictate the need for simple blasting techniques.Hence, a pyrotechnic blasting system of sequential firing is in use at present, although research work to improve this technique is in progress.

Jan 1, 1985

By Kirkhouse C. B

Soon after the Broken Hill Limited started operations at their Iron and Steel Works at Newcastle, NSW, it was found necessary to install a mill for rolling small merchant bars, rounds, etc.An arrangement of the first mill laid down is shown on Plate 1., Fig. 1. This mill commenced operations on the 18th July, 1917.The feed for this mill was rolled in the existing 18-in. mill and sheared to the lengths required before being delivered to the billet storage yard. The billet storage yard is 90 ft. span, and is served by one 10-ton electric overhead travelling crane. Billets were placed on the billet bed preparatory to being charged into the heating furnace.The heating furnace was of the continuous recuperative with end discharge and had a hearth 40 ft. long by 10 ft. wide. The billets were pushed through the furnace by means of two hydraulic rams, which could either act together and push one row of billets, or act singly and push two rows of billets. This furnace was fired by producer gas from the producers shown on Plate I., Fig. l.The gas was conveyed to the furnace by means of a brick underground flue.

Jan 1, 1935

By Osorio J. D C, McMahon M. D

Burwood Beach Sewage Ocean Outfall is being constructed by the Hunter District Water Board as part of an amplification scheme to eliminate pollution from adjacent bathing beaches. The outfall consists of a 93m vertical shaft, 1950m of 2.7m diameter tunnel with a series of diffuser outlets connecting the seaward end of the tunnel to the sea floor on a rock outcrop. The site of the work is in the Newcastle Coal Measures and the project is complicated by the proximity of colliery workings to tunnel alignment, although the colliery records provided valuable information on geological features. The location of the tunnel was determined to be in the Waratah Sandstone Formation immediately below the colliery workings after three different alternatives were considered. The shaft, which will be sized to suit contractor's construction methods and equipment, will be sunk through about 24.5m of alluvial material and 68.5m of rock. The tender documents were developed to allow the contractor considerable flexibility in construction method to suit available equipment. The specification also allowed great flexibility in tunnel construction method with minimum cross sectional area of 5.7m2 being the basis for a number of allowable alternative profiles ranging from circular to horseshoe.

Jan 1, 1987

The cost of power is an important matter to mining companies generally and this thought that the members of the Australasian Institute of Mining Engineers, as well as the engineering and mining professions generally would be interested in any proposal for the reduction of that cost-has led to the presentation of this paper.The writer trusts that the description will be found clear and increase the interest in this exceedingly interesting subject. In the working up of the electrical arrangements touched on in this paper, the author has had the able assistance of hisfriend Mr. F. J. Mars, to whom he offers his hearty thanks. The selection of the best class of power plant for a mine is a very difficult and large problem and it is quite out of place to dogmatise that anyone of the many systems that offer isbetter than another, eg that the all electrical is better than the partly direct steam-driven and partly electrical, or that a gas plant is better than a steam plant.Such a selection is one that calls for very careful and close consideration, in each particular case, of a large number of regulating factors before it is possible to arrive at a proper decision.

Jan 1, 1911

Among countries afflicted with insLantaneous outbursts of coal and gas, Australia is noteworthy because of lesser disturbances of the seams and of the occurrence of CO2 in the seam gas from place to place. Research sLarted with the 1954 occurrences at Collinsville and Metropolitan Collieries leading to early publications reviewing the problem, describing occurrences and assessing variations in proneness factors in the two affected coal basins.The basic requirements for proneness include coals of high gas sorptive capacity, high ground stress, use of a mining method which provides higher stress concentrations and limits emission of seam gas, including high rates of advance. With CO2 in the seam gas proneness is greater.The mechanism is complex and not fully understood, but involves the coal, the roof, the floor, the gas, the mine opening, the ventilation, the kind of work and the rate of work. Geological disturbances such as faults and dykes increase proneness and tend to localise occurrences. On-occurrence of outbursts in some mines is difficult to explain.Outbursts are seen as a continuing threat to modem deep Australian mining of high rank coal.The simplest contributory factor to reduce is gassiness - despite the low permeability of outbursting coals - and present practices are showing promise. The greatest challenges for the future are partial degasification to below a known threshold figure and confirmation that this reduction is achieved and identification of anomalous geological structures ahead, the most likely locations for instantaneous outbursts to occur. The advances made to date give promise of a future with reducing experiences of uncontrolled instantaneous outbursts. For the Bulli seam particularly, working to achieve prediction and prevention is most urgent.

Jan 1, 1993

By Rowlands N. J, Zimmermann D. O

The Engel Model search simulator is described with particular emphasis on preparation of input parameters. The computer has a "black box" role in the same way a telephone or radio is a "black box" in communications. A search technique (sensor) is selected and applied in two stages of'search, namely, reconnaissance and detailed. The model relies on knowing and quantifying the parameters of the target sought and the search technique; this is usually done by analogy studies from available literature and experience. The parameters are then balanced by feasibility studies on the search area. Case histories show that the study makes the user aware of what he is likely to find rather than what he wants or needs to find to be viable. Two case histories are presented: one for Mississippi Valley type lead- zinc deposits and another for stratiform copper. The first study showed particular benefits in the input stage and highlighted the fact that one could expect a lot of encouragement by way of interesting results but with little chance of finding the high-grade,

Jan 1, 1974

By E A. Agorhom, M Beyuo, C Owusu, I Quaicoe

Understanding the mineralogy and liberation of gold particles in an ore is key to the development and optimisation of gold processing operations, being cyanidation or gravity separation. This can be achieved through basic historic geological information, gold deportment studies, chemical speciation and metallurgical test works. The present study assessed the nature of the occurrence of gold particles (mineralogical composition, liberation, associations and surface chemistry) and its effect on the process route (cyanidation and gravity separation) of a typical paleo placer gold ore deposit within the Tarkwaian Rock system. The investigative approach used involved chemical assay, quantitative X-ray diffraction (QXRD) and quantitative evaluation of minerals using scanning electron microscopy (QEMSCAN). The ore samples (A, B, C, D, E, F) used were obtained from six active pits of a gold mine working on this orebody. The results of the mineralogical analysis revealed that the ore is highly oxidised and comprised quartz (>80 per cent) and Muscovite mica (>6 per cent) as the major mineral phases in all the samples. Trace amounts of hematite, kaolinite and todorokite were also identified in all the samples. The chemical analysis showed presence of gold (Au) in all the samples with samples B (3.62 g/t) and C (3.96 g/t) containing the highest concentrations. Trace amounts of copper (Cu), iron (Fe), sulfur (S), aluminium (Al), arsenic (As) were also detected in all the ores. The QEMSCAN mineralogical liberation and gold association results revealed that the gold grains were relatively coarser in all samples (P80 > 80 µm Au in size) except F (P80 < 32 µm Au in size). Gold grains were highly liberated especially in sample B with the majority of the locked gold grains forming complex associations. All the samples responded well to cyanidation and gravity separation except samples C and F, respectively.

Aug 24, 2022

By Sharmil Markar M

Ballarat Goldfields Limited is currently re-opening the old workings of the East Ballarat Goldfield which contain an estimated 1800 ML of groundwater. The disposal of this &apos;minewater&apos; was of concern: the minewater is of moderate salinity; increased salinity levels have interfered with agriculture and water use at a number of locations downstream from Ballarat. Extensive numerical studies indicated that treated minewater could be discharged into the Ballarat Creek system for dilution by sewage effluent and by surface runoff after rainfall events. An automatic real-time salinity management system has been developed to enable the disposal of saline minewater in this fashion. A desk top computer operates the system: discharge and salinity readings are taken automatically each hour and filed away; the maximum allowable rate of discharge of treated minewater is calculated; pumps are switched on and off. The system readily enables daily, weekly and monthly data reports together with floppy disks of &apos;raw&apos; data to be prepared in formats suitable for direct submission to the Victorian Environmental Protection Authority.

Jan 1, 1990

By Richmond A

Like many industries the coal mining industry has, since the beginning of this century, undergone many changes. Technological advances and the increasing demand for fossil fuels have introduced new mining methods and techniques which allow the extraction of thicker and deeper coal seams at higher rates of production. Most new methods of mining (or for that matter any other processes) introduce problems which the engineers of the industry are expected to face and resolve. Unfortunately, spontaneous combustion has plagued the coal mining industry since the first attempts to mine coal, and is no doubt partly responsible for the reputation that coal mining is a hazardous industry. The financial loss and toll of human lives due to the occurrence of spontaneous combustion of coal in coal mines is enormous, if not incalculable. Its occurrence today is less likely to claim lives, due to both improved methods of working and in the detection of spontaneous combustion sites.

Jan 1, 1983

By N Robson, E Stephens

Australian mining companies are actively exploring for and developing mineral deposits throughout the world with interests in emerging markets such as Africa, Asia and South America. It is important to understand emerging market risk as this will affect the willingness of mining companies and financial institutions to invest in a country, especially with reference to their key asset, the mining licence or operating/concession agreement. Mining companies looking to develop new projects in emerging markets have different risk profiles than projects in countries such as Australia and Canada. Examples of key risks faced in emerging markets include: political û expropriation, nationalisation, contract frustration, currency inconvertibility, war, terrorism, strikes, riots and civil commotion; and legal û mining legislation, arbitration and dispute resolution, trade agreements. There is a problem in the difference in risk perceptions between mining companies, financial institutions and insurers. This can cause different stakeholders to carry out different evaluations of the risks faced by a project, resulting in confusion about the risk margin attached to any project. In a time where resource nationalisation and energy security are prompting governments to become more involved in the mining sector we run through some recent examples of mining companies that have had problems due to the key risks highlighted earlier. Importance of carrying out the right due diligence to replace perceptions with reality: early identification of risks û detailed due diligence on emerging market risks that may arise will help with their identification and mitigation, make use of companies that can help identify risks and suggest solutions, control the cost of financing û risk margin applied to a project finance loan will be influenced by the risks faced, and risk management and using political risk insurance. There are plenty of opportunities in emerging markets but it is important to recognise the associated risks. Detailed due diligence at an early stage will provide long-term benefits.

Jan 1, 2007

This paper firstly reviews the requirements for container and hopper design for reliable discharge. Discussion is then directed to the evaluation of the consolidation stresses acting in both in both the cylinder and hopper sections during both initial and flow conditions. Here the vast difference, especially in vicinity of the bin outlet, between the initial or filling and flow conditions is highlighted. This vast difference has major design and operation implications. A further major implication is that all bulk solids must dilate to flow. The opportunity to simultaneously attain reliable discharge and partial moisture removal is also examined.The selection of design parameters to maximise the consolidation stresses in both the cylindrical and hopper sections is detailed. In regard to the latter, it is recommended fine coal bins be discharged using low friction lined transition hoppers with large outlet spans. Such outlets will discharge fine coal in a relatively compacted state. This compaction state should exhibit minimum water retention and short term moisture uptake.

Jan 1, 1998

By Larsen D. F

Minor iron formation related base metal sulphide mineralization occurs in granulite facies metamorphic rocks of the early Proterozoic Willyama Complex. Rock sequences hosting three iron formation related Cu, Zn, Pb prospects from the Thackaringa Group (Suite 3) are described. A caparison of host rock sequences, style of mineralization and facies of iron formations suggests major differences in terms of the overall depositional environment. However, significant similarities are present with respect to the nature and distribution of iron formation facies and the occurrence of chlorite &apos;alteration&apos; zones in close proximity to mineralization in all cases. The chlorite within these zones occurs in a number of diverse forms in a range of rock types. A comparison of the prospects shows that there is no evidence to indicate that the chlorite in the zones is a retrograde alteration product of former higher grade prograde mineralogies - the chlorite appears to have survived granulite facies metamorphism. The mode of occurence of the chlorite in the &apos;alteration&apos; zones together with the fact that the association quartz + chlorite + magnetite + pyrite + base metals is cx rmn to all areas suggests that the chlorite is specifically related to the processes which deposited the stratiform iron formations and related sulphides. It is considered that the chlorite precursor was a prenetanorphic alteration product or chemical sediment closely related to submarine hot spring activity which was also the source for chemical sediment precursors of the iron formations, associated lode rocks and Sulphides.

Jan 1, 1983

Pyrrhotite is the predominant gangue mineral at Renison comprising about 60 percent of the sulphides in an average ore blend. It exists as two crystal structures - monoclinic and hexagonal. Monoclinic pyrrhotite is the slowest floating of all minerals but is ferromagnetic and hence recoverable more efficiently by low intensity magnetic wet drum separators than flotation. This paper discusses the installation and commissioning of four 0.915 m x 3.0 m, 0.1 Tesla permanent magnet, wet drum separators prior to sulphide roughing flotation. Planned circuit and process control modifications to better accommodate magnetic separation into Renison&apos;s flowsheet will be Discussed.

Jan 1, 1991