Search Documents

By Z Terzic, M Schult, D Chu, S Macklin

The East West Link road tunnels are proposed to provide a connection between the CityLink toll road and the Eastern Freeway north of the Melbourne CBD. The alignment passes from Moonee Ponds valley beneath the Upfield Line railway cutting, Royal Park, the historic Melbourne Cemetery and beneath Alexander Parade rising to an eastern portal at Hoddle Street. The western (Royal Park) part of the alignment passes through the folded and faulted Silurian Melbourne Formation, which has been subjected to deep weathering since the Triassic.The Melbourne Formation in the Royal Park area is mainly characterised by interbedded sequences of siltstone and fine-grained sandstone. The beds are often graded and a clear boundary between the siltstone and fine-grained sandstone rock can be difficult to distinguish. Variation in lithology and the presence of structural geological features such as folds and faults have resulted in an irregular weathering profile within the Silurian rock; nonetheless the formation typically becomes less weathered with depth.Due to difficulties in obtaining reliable laboratory strength and stiffness relationships with weathering grade, in situ testing methods such as downhole shear wave velocity and high-quality pressuremeter testing are a useful aid to assessing appropriate geotechnical parameters for design.This paper presents an analysis of the variation in shear modulus of the Melbourne Formation, determined at small-strain (from downhole seismic data) and at ‘engineering scale’ strain (from pressuremeter tests) for extremely weathered (XW), highly weathered (HW) and moderately weathered (MW) rock. Estimates of small strain shear modulus (Go) obtained a range between 400 to 3400 MPa for these weathering grades. By comparison against the pressuremeter test data, reduction factors to be applied to these Go values to estimate shear moduli at engineering strain levels typically range between 0.10 and 0.35.The downhole geophysics undertaken in the Royal Park boreholes also suggests that there is an inversion in velocity between approximately 15 and 27?m depth below the top of the formation. This is thought to be related to the effects deep Plio-Pleistocene weathering, iron cementation of joints and increasing frequency of ‘non-healed’ joints in the transition from MW to slightly weathered (SW) rock.CITATION:Macklin, S, Schult, M, Terzic, Z and Chu, D, 2014. Strain-dependent stiffness of the weathered Melbourne Formation, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 179–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By G Chitombo, A Perryman, A D. Campbell, J White, B Hollis

This paper describes the development and implementation of an optimisation tool developed as part of the Mass Mining Technology (MMT) Project. The tool, known as the SLC Schedule Optimiser, is capable of optimising the schedule of development and production activity for a sublevel cave, given a fixed draw strategy, for the life of the mine.This paper starts by describing the development and production scheduling problem for a sublevel cave, the geotechnical constraint that a schedule of activities must adhere to, and outlines the pre-existing manual planning procedures used to produce schedules.Following this, the paper then outlines the optimisation tool developed, describes the changes to the planning process it has enabled and finally quantifies the improvement to operations this tool has brought using Glencore’s Ernest Henry Mining Operations as a case study.CITATION:White, J, Perryman, A, Campbell, A D, Hollis, B and Chitombo, G, 2016. Life-of-mine development and production scheduling optimisation for sublevel cave operations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 133–138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M L. Muller, A R. O’Donnell

The Mount Isa Mines (MIM) Copper Concentrator has an extensive history of reagent trials, with different reagents coming in and out of favour over the years. The research and use of carbon depressants is particularly prevalent, as carbonaceous pyrite is a major source of concentrate dilution. Years of research led to the use of naphthalene sulphonate due to its excellent carbon depression properties. However, due to rising reagent costs carbon depression ceased in the late 1990s. This led to the loss of knowledge about the use and value of naphthalene sulphonate. Cyanide is used at the Copper Concentrator for the sole purpose of pyrite depression and over the years multiple projects have been devoted to finding alternatives to it. In 2012 the neighbouring MIM Lead-Zinc Concentrator replaced cyanide with naphthalene sulphonate which resulted in cost savings and the elimination of a hazardous reagent. In 2013, plant trials were conducted at the Copper Concentrator in hopes to replicate the outcomes obtained at the Lead-Zinc Concentrator. The results of the trials conducted at the Copper Concentrator showed that naphthalene sulphonate could not replace cyanide and this work was set aside to pursue more promising projects. Further research conducted in 2014 found that mineralogy and a better understanding of the depressing mechanism of naphthalene sulphonate held the key to improved pyrite depression at the Copper Concentrator. The findings showed that Mount Isa copper ore contains two forms of pyrite; euhedral pyrite (cubic pyrite) and framboidal pyrite (carbon rimmed spheres of pyrite), both of which require different reagents to sufficiently depress them. Naphthalene sulphonate was found to be an excellent carbon depressant, suitable for depressing graphite and framboidal pyrite, whilst cyanide specifically targets euhedral pyrite.In 2015 laboratory test work was conducted to examine the use of naphthalene sulphonate in conjunction with cyanide to selectively target both forms of pyrite. This work led to a full plant trial, the results of which showed a significant increase in plant performance, with higher copper concentrate grades and recoveries being achieved. This paper aims to focus on the benefits and importance of understanding past work and linking a detailed knowledge of feed mineralogy to reagent selection for improved plant outcomes.CITATION:O’Donnell, A R and Muller, M L, 2018. Selectively targeting hydrophobic gangue minerals at the Mount Isa Mines Copper Concentrator, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 413–421 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By P Dare-Bryan

Many mines have an interest in improving fragmentation at their sublevel caving operations in order to produce better ore recovery, lower dilution and less overbreak. The primary requirement for the extraction phase is to understand and optimise the flow of the fragmented rock in the rings including interactions with the caved material. Rock fragment formation is critically controlled by the blasting phase and can potentially be improved by optimising the dynamic energy distribution throughout the ring through the crafting of explosive charging, priming position and initiation timing. The modelling of fragmentation and damage due to explosive loading of complete rings is inherently and irrevocably a three dimensional problem that is difficult to address. We have therefore initially utilised an analytical code to predict vector peak particle velocities and energies that are restricted to the plane of a ring. Dynamic energy distributions based on common timing and priming practice have been compared with other possibilities using conventional pyrotechnic detonators as well as initiation designs based on accurate electronic detonators. The energy distribution can be quite subtly tailored to increase energy in appropriate regions or to decrease energy in the brow region for example to potentially reduce instability and the probability of misfires. We have also recently developed the capability to efficiently model particle flow using four-sided polygonal elements. Despite the 2D limitations of such a model this results in more realistic fragment interaction and stacking than can be achieved using conventional rigid circular elements. Modelling of a typical sublevel caving ring utilising these elements activated by the correct dynamics offers considerable potential for understanding the influence of the blasting energetics and timing on the complex flow and extraction process.

Jan 1, 2005

Outsourcing of mining operations and services is done for various reasons and there is no single model which fits all situations. Experienced contractors and mine owners have also developed, more often than not, jointly, numerous commercial arrangements and project delivery methods to suit their particular project. It is often the case that some mine owners who have not considered outsourcing to contractors do so because of a simple lack of understanding of the potential benefits. This paper will highlight the potential benefits and perceived disadvantages of outsourcing for mine owners and demonstrate how these issues have been addressed by the mining contracting community over recent times as well as demonstrate the evolution of current commercial arrangements in engaging mining contractors.

Jan 1, 2006

By C Rizos

Many of the ‘new paradigms in mining’ and notions of ‘sustainable mining’ have at their core the requirement for reliable, continuous centimetre-level positioning accuracy to enable increased automation of mining operations. The deployment of precision systems for navigating, controlling and monitoring machinery such as drills, dozers, draglines and shovels with real time position information increase their operational efficiency, and reduce the need for humans to be exposed to hazardous conditions. The Global Positioning System (GPS) is the best known, and only currently fully operational, Global Navigation Satellite System (GNSS) providing positioning capability anywhere in the globe, on a continuous 24/7 basis, with accuracies ranging from the dekametre-level to the sub-centimetre-level depending on hardware and operational configuration. Despite this versatility, GNSS cannot satisfy the high accuracy positioning requirements for many applications in mine surveying, and mine machine guidance and control. The reason is that increasingly open cut mines are getting deeper, resulting in a reduction of the ‘sky-view’ necessary for GNSS systems to operate satisfactorily. Yet, to date there have been no viable alternatives to GNSS that can be deployed in mine environments that can meet the challenging requirements in open cut mines.Locata Corporation, a Canberra-based company, has invented a terrestrial high accuracy positioning system known as ‘Locata’ that can augment GNSS with extra terrestrial signals to permit cm-level positioning accuracy even when there are insufficient GNSS satellite signals for reliable positioning and navigation. Locata relies on a network of synchronised ground-based transceivers that transmit positioning signals that can be tracked by suitably equipped user receivers. Hence Locata can be considered a new type of ‘local constellation’, able to provide high accuracy positioning coverage where GNSS fails. This paper introduces some of the technical aspects of this Australian technology and describes tests conducted by Leica Geosystems over the last few years at Newmont Boddington Gold in Western Australia. A recent news announcement by Leica Geosystems (12 January 2011) has confirmed that their new mine management system will have combined GNSS + Locata positioning capability – the first commercial product that integrates GNSS and Locata capabilities into a single high accuracy and high availability navigation device for open cut mine machine automation applications.

Nov 22, 2011

In Australian collieries, solutions to the outburst problem must be implemented in a highly competitive environment which has a low tolerance on negative productivity effects. Solutions are only applicable if the overall viability of the operation remains sound. Minimum time must be spent on alleviation and control measures. This is favoured by simple geology, advanced warning and efficient alleviation and control procedures. Research requirements in support of this include 1. an improved means of predicting the nature and location of outburst zones ahead of the face and, 2. an improved means of measuring the effectiveness of gas drainage. For additional safety at the face, a means of continuously monitoring outburst proneness is required. In general, greater emphasis is required on improved instrumentation.

Jan 1, 1987

By Marshall B, Gee R. D

Geological data processing by machine enables'an increased rate of coverage, better supervision and control of field programmes, increased effectiveness of field operators, and vastly improved access to old and new field data. Even a system of restricted felxibility enables a mapping programme to be organ- ized and conducted independent of personnel changes, whilst elimination of much compilation time increases the rate of cover- age such that it relates to mode of transport and geological complexity rather than to personality factors. A machine is useful only if applied to tasks suited to its capabilities, and must be aimed at those types of mapping in which a limited number of attributes adequately define the problem, and the data is of a form suited to coding and is normally collected in sufficient abundance to make compilation wearisome. Machine systems are therefore unsuited to most types of lithological mapping and to most types of exploration in new areas, but have proved useful in many branched of cartographic geophysics (e.g. gravity and magnetics), and in cartographic Geochemistry.

Jan 1, 1969

By Schonert K

The throughput of a HP-roller mill is determined by the acceleration of the feed material within acceleration zone and introduction into the compression zone. Both processes depend on the internal friction and the friction of the material on the roller surface which is influenced by the surface structure and adhering of material. The particle motion in the acceleration zone has been investigated with high speed videos showing the effect of the centrifugal force and the slip on the roller surface. The throughput is discussed in the term of the specific throughput which can be approximated by a linear function characterised by the throughput number and the throughput elasticity. The throughput number is a helpful measure for investigating the influence of the feed material and the surface structure. The experimental results give some guidance for chosing an optimum corrugation profile.

Jan 1, 1993

The process of evaluating orebodies at the feasibility study stage is extremely important. In recent times many groups have indicated that they would like ore reserve estimation to be numeric and objective. Whilst sampling, geological, mining and mathematical principles may be used to analyse the data, all ore reserve methods require the use of experience factors and as such are value j ddgment statements.

Jan 1, 1990

Data logged on mineral beneficiation processes during normal operation are analysed using time series (correlation and spectral) methods to identify the dynamics of the processes for on-line computer control. Recursive least squares estimation techniques are used to identify parametric models for a cassiterite flotation circuit and a coal washery. Identification problems such as the determination of model order, process time delays and the 'contamination' of the data by process recycle streams (feedback) are discussed. Typical results are presented in which optimised models are identified from data logged during normal operation.

Jan 1, 1985

Mt. Whaleback is in the Pilbara region of Western Australia approximately 1200 kilometers north of Perth, the State capital. In this deposit the Mt. Newman Joint Venturers are mining ore reserves totalling 1500 million tonnes of high grade hematite averaging 64.0% Fe. In addition to Mt. Whaleback, 38 ore bodies have so far been identified outside Mt. Whaleback on the Company's remaining 75,000 hectares of lease area. These ore bodies contain major tonnages of iron ore. Extraction at present is planned at a rate of 37 million tonnes per annum at an ore-to-waste ratio of approximately 1 to 1.4. The ore is railed north to Port Hedland on the Indian Ocean where the different products are screened, crushed and blended prior to shipping. The purpose of this paper is to acquaint the reader with the facilities installed in the Mt. Newman operation to form a background to the sampling techniques employed, describe the precisions which were achieved in experiments conducted February through June, 1976 and also to assess the degree of blending which takes place during the various processes and to put a quantitative measure to the degree of blending. There have been many excellent papers written on the more theoretical aspects

Jan 1, 1976

By Cheung L. C C, Maconochie A. P

SIROFRAG is a computer-based imaging system that quantifies the post-blast rock fragment size distribution in a muckpile in a mine environment. Improvements in blast performance and blast modelling are being hampered by a lack of a quick and objective method to evaluate the major result of the blast: the fragment size distribution. This is usually done by hand digitising muckpile photographs: a labour intensive and tedious process. SIROFRAG is being developed to quickly, cheaply and objectively provide this information. SIROFRAG is based on active stereo image analysis. It uses a light stripe to illuminate a muckpile and a pair of video cameras to determine the 3D nature of the scanned objects. The imaging system is based on a novel prototype scanning projector that allows images to he captured in full daylight. The Microsoft Windows based software controls the projector and interprets the captured images to provide a size distribution of exposed rock fragments.

Jan 1, 1995

Geological information plays a significant, cost effective role, in the Mt Whaleback iron ore mining operations. The geology and structure are complex. Good communication between the Mine Planning Production Scheduling and Quality Control Sections is the key to utilisation of geological information to its full potential.Drilling and pit face mapping are the two basic sources of detailed data sets which are processed to prepare up to date geological cross sections and benchwise geological plans. This information is used directly for the blast pattern design and production scheduling. Physical ore type estimation is also undertaken. Orebody models are generated from the geological information.

Jan 1, 1990

By McMahon DW, Schapper MA

Hard rock underground mining has been wedded to the drill-blast method of breaking rock. Current practice and technology have focused on greater efficiencies in the blasting and handling of ore, on the basis that thelower costs that come with larger scale operations compensate for the waste dilution associated with the bulk methods. However, it is suggested that new technology is available or is on the horizon that could completely change the shape of hard rock mining in the 21st century. Hard-rock continuous-mining machines, possibly assisted by high pressure water jets, coupled with automated sorting and materials handling systems, could re-orient the miner's focus to winning metal rather than mining tonnes of ore. More continuous mining processes could accelerate the penetration by high technology in the hard rock underground mine, with the potential of greater manpower productivities and lower costs per tonne of metal produced. This new technology will be important in maintaining a competitive supply of metals, given the falling headgrades of the orebodies remaining for development and the increasing market threat from manufactured substitutes.

Jan 1, 1985

The results of about 30 years of exploration and mining activities and research studies in the Kambalda mining district, Western Australia, have led to general agreement that the komatiite-associated Ni sulphide ores formed as a result of igneous processes (Ross, 1974; Ross and Hopkins, 1975; Gresham and Loftus-Hills, 1981; Cowden, 1988; Lesher, 1989 and many others). Despite this agreement, the controls on sulphide supersaturation and concentration of the resulting sulphide in a limited zone, remain uncertain and controversial. A major uncertainty is the source of sulphur in the ore deposits. Two principal sulphur sources have been proposed: 1. komatiite lava/magma (Hudson, 1972; Naldrett, 1973; Lesher et al, 1981; Cowden, 1988; Foster et at, 1995), and 2. sedimentary material (Groves, Barrett and McQueen, 1979; Lesher, Arndt and Groves, 1984; Lesher, 1989; Lesher and Campbell, 1993). Resolution of the uncertainty regarding the sulphur source is required for a complete understanding of the controls on ore formation, which in turn would significantly impact exploration strategies in the Kambalda mining district and elsewhere. This paper reviews the constraints on sulphur sources for the komatiite-associated Ni sulphide ores in the Kambalda mining district. The focus is on the general characteristics of the ores and surrounding rocks: individual ore deposits are not described, though specific examples are noted where appropriate. The stratigraphic and volcanic settings and geochemical (major and trace element and isotopic compositions) characteristics of the ore deposits and surrounding rocks are considered within the context of the competing sulphur source models, and future directions of research in the district are noted.

Jan 1, 1996

By Anylmore M, Walker A, Fletcher A

Roasting of sulphide and sulph-arsenide gold ores produces unwanted emission of sulphur and arsenic oxides, and a less than complete recovery of gold. Pyrite loses sulphur and arsenopyrite loses arsenic at a useful rate at temperatures of 600¦C and above in an inert atmosphere. Sulphur and arsenic driven off can be condensed before entering the atmosphere. During the process, solid-solution gold redistributes itself on internal surfaces of the resulting iron sulphide. Two subsequent processing options may be used; direct cyanidation of the porous sulphide resulting from the anoxic pyrolysis, or a second-stage roast to oxidise the remaining iron sulphide. The first option may be viable under certain conditions of pyrolysis. The two-stage option has an environmental advantage over the traditional roast because it reduces oxide vapour emissions by 50 per cent. The second stage may provide nearly enough energy to sustain the entire process.

Jan 1, 1992

By DAVID C LAURENCE

The richer, shallower sapphire deposits of the New England region of New South Wales which have been traditionally mined by the small miner are almost worked out. Larger mining and exploration companies are replacing the small miner and exploring for the primary source of sapphire or lower grade alluvial deposits.Although in recent years considerable exploration effort has been directed at locating the primary source, commercial exploitation of sapphire is still restricted to the working of alluvial deposits.If the Australian industry is to compete against Asian and African producers it must use cost effective exploration, mining, processing and marketing methods.

Jan 1, 1990

By L Thorburn

In 2009, the Queensland Government developed a series of amendments to environmental authorities (EAs) for mines throughout the Fitzroy Basin in response to studies that assessed the cumulative impacts of mine water discharges in the basin. One of the key amendments was the requirement for all mines in the Fitzroy Basin to develop and implement a receiving environment monitoring program (REMP). The intent of the REMPs was to provide baseline information on the condition of the receiving environments of the mines and any impacts resulting from release of mine-affected water. Since this time, the requirement to complete a REMP has been incorporated into new or revised EAs for mines (including metalliferous mines) in other regions, as well as for other industries that discharge to natural watercourses (such as coal seam gas). This paper discusses the approaches that can be used to incorporate biological monitoring and direct toxicity assessments into REMPs. It highlights the importance of collecting biological data using sound experimental design principles to investigate whether releases resulted in environmental harm; and the use of monitoring data, coupled with direct toxicity assessments, for setting more realistic, site-specific trigger values and release limits (compared to the default guidelines such as Australian and New Zealand Environment and Conservation Council (ANZECC), which may not be appropriate to the region). Implementation of a robust REMP can maximise outcomes for both the proponents and the environment.CITATION:Thorburn, L, 2013. Receiving environment monitoring programs - making the most out of biological indicators and direct toxicity assessments for monitoring of aquatic ecosystems, in Proceedings Water in Mining 2013 , pp 143-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

"Cash flow modelling during project evaluation is enhanced when probabilistic methods are applied to the inputs. One of the important inputs is the quarterly production profile. Typically, the steady-state production profile provided to project evaluation practitioners is deterministic, with each quarter the same as every other quarter. This is unrealistic as actual production profiles from existing mines exhibit a range or quarter-on-quarter variance. Monte Carlo stochastic simulation of the production profile can be used to provide a range of possible outcomes, but how are these ranges selected? This paper describes the use of quarterly production variance from a large database of mines worldwide as a benchmark to inform the appropriate selection of ranges. The coefficient of variation is used to rank the production from mines, with quartile analysis applied to indicate industry best, median and worst variation. Due diligence of existing mines and evaluation of future production performance can be quantitatively assessed using this approach. Examples of the effect on value are provided.CITATION:Stewart, C A, 2016. Production variance benchmarks and their use in project evaluation and due diligence, in Proceedings Project Evaluation 2016, pp 201–213 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016