Search Documents

By P J. Terbrugge

The concept of vertical pit mining has been developed as an alternative mining method for the exploitation from surface of small, vertical or near-vertical, massive orebodies down to depths of some 200 m, where ore extraction from conventional open pit excavations is rendered uneconomic due to high associated waste:ore mining ratio. Systematic lateral support maintains vertical pit sides, thereby minimising waste mining volumes. Stability analysis techniques have been developed for design of this lateral support, with the support quantum, primarily comprising long cable anchors, dependent upon country rock strength characteristics and pit configuration. Where the cost of support is less than the cost of the comparable conventional pit waste excavation, vertical pit mining becomes an economically viable alternative, additionally providing the benefit of reduced environmental impact and rehabilitation requirements for the mining area. The technique has been successfully applied for the mining of a chrome deposit in Zimbabwe to an 80 m depth, believed to be unique in the world, and a full feasibilty study for a 3000 m2 diamond pipe has been carried out for mining to 200 m depth.

Jan 1, 2000

By B Stewart

The SRS-1200 concept came about following the recommendations from the Board of Inquiry into the 1994 Moura No 2 mine disaster with the aim of having a system to remove personnel from an unsafe environment underground via a shaft where no other means of escape is possible. It is a mobile rescue unit that utilises a winding system to operate a man cage. It can descend the cage up to 1200 m into a vertical shaft. This operation is managed from the winder control compartment located on the non-driver side at the rear of the vehicle.

May 5, 2022

By J Stiefenhofer

"*This is an abstract only*Construction of geological models for kimberlites has historically largely been based on visual volcanic textures and features, with chemical data only collected on an ad-hoc basis depending on the level of perceived complexity observed in the geological data. The focus of this paper is a high-level view of the impact an initial absence (or lack) of relevant chemical data had on two kimberlite resource models as well as how the magnitude of the problem increased once the resource estimation process commenced (Stiefenhofer, 2013). The impact of ignoring chemical data on a project assessment where micro-diamond estimation techniques are employed, is also discussed. Resource estimates based on micro-diamond data are critically dependent on the use of the correct geological model since stationarity of the size frequency distribution is key to the generation of correct grade estimates. A multilevel approach is advocated where the volcanological/visual model is verified using chemical data and both are in turn verified by the diamond data.CITATION:Stiefenhofer, J, 2013. The use of chemical and metallurgical parameters to enhance the economic value of kimberlite resource models, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 101-104 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By L Hussey

Mt Keith concentrator treats low grade disseminated nickel sulfide ore supplied from the adjoining open pit mine. It is a traditional crushing, two-staged closed circuit grinding circuit (SAG & Ball Mills), followed by a complex split-size rougher, scavenger and cleaner flotation circuit. In 2016, 10.5 Mt was milled, at an average head grade of 0.54% Ni, yielding 35 000 nickel metal tonnes in concentrate.Historical analysis of the plant data indicated that of all the nickel lost in the fines rougher circuit tails stream, 25.6% was recoverable in an eight minute laboratory scale flotation test. These results implied that this fine nickel was readily available for recovery in the plant, either through operational improvements or additional flotation capacity. With operation optimisation ongoing, and capital within the business focused elsewhere, plant personnel were challenged to think differently about improving recovery.In 2012, a separate project to improve plant recovery when treating high talc ore was completed. Amongst other vessels, this project saw the installation of two 150 m3 Outotec Cells to the scavenger section of the fines rougher, middlings and scavengers (RMS 1) circuit. Since installation, the operation of these cells resulted in difficulties immediately upstream with instability in the scavenger cells. It was therefore decided that these cells would be better suited to treating the fines rougher circuit tails.The alterations required to divert these flows were minimal, with the capital project totalling $220 000.In the two years since installation, the fines rougher tailings nickel grade has dropped by 9.9%. The scavenger circuit has also seen a 2.8% reduction in tailings nickel grade, and instability issues were immediately resolved. This project serves as a lesson in how existing plant infrastructure may be better utilised to maximise recovery. Although this is especially applicable when capital constrained, such re-appropriation can be considered at any point to maximise return on existing assets. CITATION:Hussey, L, 2017. Repurposing flotation capacity at Mt Keith nickel concentrator, in Proceedings MetPlant 2017, pp 254–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By J Välivaara

The mining industry will face numerous challenges over the next 10–15 years as new deposits are likely to be more remote and lower grade and existing deposits will be mined deeper. As a result, mines and mining contractors operating in deep-mine conditions will need to focus on the quality of drilling and blasting to minimise unnecessary waste rock excavation to keep costs at an acceptable level. In addition, increased demand for improved safety and operator ergonomics will set greater demands on original equipment manufacturers of mining equipment. Finally, difficulties finding a skilled and experienced workforce, particularly in remote mine locations, have already negatively impacted mines’ ability to achieve high productivity and low operating costs.This paper introduces techniques and shares practical experiences in increasing productivity and reducing the costs of excavation in underground face drilling. The paper uses Sandvik’s new DD422i automated mining jumbo as an example of the type of equipment needed to deliver the features and corresponding benefits for future mine development. Case studies using this equipment are presented to illustrate the points made in this paper.CITATION:Välivaara, J, 2016. Automated drilling features for improving productivity and reducing costs in underground development, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 723–730 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J Meikle

A projected image is not always a true representation of a situation, or indeed an industry. This is often the case of the mining and minerals industry, which has frequently been portrayed in a negative light with a male dominance stigma attached. However, these issues can be combated for both the industry and its future, current undergraduate students, through undergraduate industry experience. In particular, vacation work enables female students to dispel many myths surrounding the industry and realise that the mining and minerals field offers career development for both genders. This paper will discuss how vacation work enables students to make important career decisions even before they have graduated. Industry experience provides undergraduates with the opportunity to gain practical knowledge relevant to their field of study. Additionally it allows students to observe the nature of the industry and the sacrifices necessary to advance careers. The prior insights into an industry are relevant to all students, but particularly female students, who might otherwise be dissuaded from a career in mining. This paper is written from the perspective of two female undergraduate students studying Mining and Minerals Processing Engineering.

Jan 1, 2006

By I M. Platten, Y Xie

Narrow vein gold mineralisation generally contains both fine (<100 ¦m) and coarse (>100 ¦m) gold particles. The in situ size and shape, deportment, distribution and abundance of the particles controls deposit sampling characteristics, grade distribution and metallurgical properties. Particles can range from individual disseminated grains, clusters of particles and masses above 1 cm in size. At each end of the coarse-gold to fine-gold spectrum, the samplability of a deposit ranges from relatively simple for fine-grained disseminated gold particles, through to extremely difficult for very coarse particles. Deposits generally show a background grade of mineralisation dominated by disseminated fine gold particles. Drilling will resolve the background grade well, though is likely to considerably understate the grade related to the coarser gold particles. Gold mineralogy has a significant impact on metallurgy, with key factors affecting recovery being particle size, deportment, liberation parameters and silver content of gold minerals. For coarse gold particles the focus should be on liberation and the early removal of the particles from the mill circuit by gravity concentrators and gold traps. Finer particles will require more grinding to liberate prior to flotation or cyanide extraction. The determination of gold particle sizing is thus required to minimise evaluation and geometallurgical uncertainty and lower project risk.

Jan 1, 2008

By M C. Ackland

The Grande Côte Mineral Sands Deposit (GCMSP) is located on a coastal mobile dune system in Senegal on the west coast of Africa. Senegal is a stable, democratic republic, having gained its independence from France in 1960. It has a population of about 12.5 million people. The dunes begin about 25 km north-east of Dakar, the capital city of Senegal, and extend northwards for more than 140 km. The mineralised dune system averages about 2 km wide with some areas extending to up to 4.5 km wide.Mineral Deposits limited (MDL), a Melbourne-based company with over 60 years operational experience in mineral sand mining in Australia, holds, through its Senegalese subsidiary MDL Senegal SARL (MDLS), a 25-year Mining Concession covering the deposits. The main heavy mineral (HM) areas identified to date are, from south to north, Mboro, Fass Boye, Diogo and Lompoul. Within the Mining Concession there is potential to identify additional resources beyond the limits of present drilling. The dunes are mobile or semi fixed, pale yellow in colour and overlie older white marine sands. The dunes range between 5 m and 30 m in height and the mineralised zones, which are essentially flat-lying, average around 15 m in thickness. The mineralisation consists, principally of ilmenite with accessory zircon, rutile and leucoxene. Zircon and ilmenite are the main commodities of interest.Independent consultants AMC estimated mineral resources for the four main deposits in 2006 of 1330 Mt of sand averaging 2.0 per cent HM at a cut-off grade of 1.5 per cent HM. At a cut-off grade of one per cent the resources were 3200 Mt averaging 1.5 per cent HM. All of the estimate was classified as Inferred Resources under the 2004 Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (JORC, 2004).Subsequent completion of infill drilling, sampling and assaying of the initial mining area, centred at Diogo, was completed in 2008, enabling a final dredge path to be designed and ore reserves estimated, based on a JORC compliant Measured and Indicated Mineral Resource. Infill drilling is continuing in the Lompoul and the results of this campaign will be included in the JORC compliant data base by AMC in April 2010 to enable the 15 per cent year dredge path and mine plan to be finalised.Development studies have shown that the project can be optimised as a dredging operation, with mineralised sand being treated in a conventional floating spiral preconcentrator, wet concentrator and dry mineral separation plant. Engineering work now substantially completed by Ausenco Limited (Ausenco) has developed the combination of some existing plant from MDL’s past operations, and new plant for the complete process from dredging to final product separation and grading. Testwork on a series of bulk samples has determined that the project can yield a high quality zircon product and an ilmenite product along with minor rutile and leucoxene.Work to date indicates a likely output of around 80 000 t of zircon in various quality streams (Primary, Secondary, Standard and Foundry Grades), around 550 000 t of ilmenite plus around 15000 t of rutile and around 12 000 t of leucoxene/secondary ilmenite. Planned zircon output would represent around 7per cent of the total world production, which would make the GCZ&IP a significant producer on a world scale.The studies have indicated capital costs to be in the range of US$400 M total operating cost (after completion of ramp-up) of around US$50 M - $55 M/a. Revenue is expected to be in the range $127 M - $157 M/a.

Oct 5, 2011

By A Stradling

For a geometallurgical program to be successful, linkage must be made between the geologists and geostaticians who understand and model the orebody, the metallurgists who determine the value that can be extracted from the different geometallurgical units, and the mine planners who develop and optimise the plan to extract maximum economic value from the resource. One of the primary purposes of geometallurgical models is in the determination of the economic cut-off between ore and waste. Recognition of the level of confidence required in the estimation of grade, throughput and recovery is critical to the planning of a successful geometallurgical program. It also helps clarify the scope of work needed to mitigate risk at each stage in the development of a new mine projectThis presentation provides some of the author’s experience with development and application of geometallurgical models for existing base metal operations. It discusses how geological units defined by lithology, structure, alteration etc, can be translated into geometallurgical ore types defined by mineralogy, ore hardness, and flotation behaviour. Examples of how these characteristics have been used to estimate key economic parameters such as mill throughput and flotation recovery at two brown-field operations are provided. The first example relates to the modelling of metallurgical performance at Teck’s Red Dog zinc-lead mine in Alaska. Prior to 2000, zinc, lead and silver recoveries from a block of ore at Red Dog were either assumed constant, or were varied according to simplistic models. Throughput was not thought to vary substantially between blocks, so an average value was used for each blended stockpile. It is quite possible that some ore-value blocks were classified as waste, and some waste-value blocks treated as ore, as a result of poor understanding of the true economic cut off across the wide range of ore types observed at Red Dog. After an extensive flotation test program, the first assay-based zinc recovery model was developed for the Main pit reserve in 2003.**This is an abstract only. No paper was prepared for this abstract**

Sep 5, 2011

By M Paakkunainen

Sampling is often the most critical part in process analysis. When the mean of a continuous lot, such as a process stream within a given time interval, is estimated by calculating the mean of several samples, the uncertainty of the estimated mean depends usually on the sampling strategy. Three different strategies can be used: systematic, stratified or random sample selection. The standard deviation of the lot mean is different for these methods so that systematic sampling usually gives the smallest and random sampling the largest standard deviation. Pierre Gy developed a method where the sampling errors of one-dimensional lots for these three strategies can be estimated from a variogram, which is calculated from a variographic experiment, ie from a set of one-dimensional time series measurements with fixed sampling interval. While variogram is an excellent tool for characterising and displaying the variability of autocorrelated processes as function of time, the sampling error estimation from it is quite laborious, however. In this work an alternative method for estimating the sampling errors was developed. The process is divided into strata of equal sizes, varying the length of strata similarly to variographic analysis. For stratified sampling the standard deviation estimates are obtained by analysis of variance and for systematic sampling by fitting a linear regression line to each stratum and calculating the residual variances. By pooling the individual variance estimates the variance estimates that are corrected for autocorrelation are obtained. The new method was tested with simulated and real data sets having periodic, random and/or drift fluctuations. For stationary processes the results agreed well with the results of the GyÆs variographic method. The method can probably be generalised to estimate the sampling variance of higher-dimensional lots.

Jan 1, 2005

By S Pontual

The use of spectral data has traditionally been for obtaining mineral information and for mapping out alteration systems. The output from these data is typically in the form of mineral assemblages and data on relative proportions of minerals. However there is much more than just mineral information in the spectral data. Most importantly, the data allow the user to obtain vital information on mineral chemistry for some key alteration minerals. The mineral chemistry data allow the users to evaluate multiple phases of alteration of the same key mineral species, and to assess which phase is related to mineralisation. Mineral indices can be extracted from the spectral data and plotted to represent variations in the chemistry and relative proportions of key mineral phases as downhole, section and three-dimensional (3D) plots. These data can also be compared with the spatial distribution of the mineralisation by integration with geochemical and logging data. Through spatial and statistical evaluation the mineral information obtained using spectral analysis can provide vital information to assist in building alteration models and therefore improve targeting for further drilling and exploration.

Aug 22, 2011

By M Scoble, E Rubio

The re-engineering of manufacturing production systems has demonstrated the benefits from using production information for optimising processes. This paper explores the techniques and issues in the acquisition and analysis of mine production data for tactical decision making in production control. The use of information and operations management tools is presented in the context of block caving studies, with particular focus on the relationship between secondary breaking and LHD production performance.

Jan 1, 2000

By DV Boger

Rheology is the science which deals with the deformation and flow of matter. Thus nccology is concerned with the flow of any material. The mining industry is concerned with digging things out of the ground, extracting the good stuff and throwing away the had stuff. In the upgrading processes associated with mining, is mineral processing, wet techniques are used where the primary material being handled is a particulate fluid, ie a suspension. After the processing operation, with the concentrates extracted, what is left behind generally is a wet material in suspension form, which may or may not contain reagents harmful to the environment. The amount of waste generated in any of the mining processes is large, in fact, the mining industry is the largest generator of solid waste in Australia. In order to minimise the waste generated within the industry it has become of interest to handle the particulate fluid wastes, or suspensions, at high concentrations, thus removing water and some of the reagents which may be harmful to the environment. The resultant highly concentrated suspension is a non-Newtonian hold Rheology deals with the flow of non-Newtonian fluids; therefore i combination of rheological understanding of high density suspensions. ill conjunction with an understanding of the environmental problems hero' faced by the mining industry, can and has led to improved methods of waste disposal in the industry, ie waste minimisation. This paper describes the progress that has been made in the development of dry disposal technology in the mining and minerals industry in Australia.

Jan 1, 1998

Hard rock TBMs are very often open machine layouts, with just a part roof shield over the front of the machine. The whole system is designed for fast face advance and the economy of the project often depends entirely on the rate of advance. Typically, hard rock conditions will demonstrate stable and good ground for a major part of the tunnel. However, short sections of crushed shear zones with clay and gouge material may cause serious time delays. Spiling rock bolting has been proven to be very efficient under such circumstances, provided the fully grouted rebar bolts can be placed in a controlled and practical manner.Environmental restrictions are becoming more and more a part of tunnel excavation projects. Even hard rock TBM tunnelling may require a strict ground water control, because of consequences on the ground surface from lowering the ground water level. Such consequences may be surface settlement, negative influence on ground water resources or damage to vegetation.Pressure injection ahead of the advancing tunnel face (in this paper named pre-injection), using microfine cement and chemical grouts, is today a proven technology. As examples can be mentioned (Garshol, 1997) about 100 km of pre-injected tunnels below Oslo City and about the same length of subsea tunnelling elsewhere in Norway. Examples from other parts of the world are also available, like below Stockholm, Sweden, the Inland Feeder project and Hollywood Metro both in Southern California.To take advantage of spiling rockbolts and pre-injection, it is an obvious prerequisite to be able to drill the necessary boreholes in the right positions and at the correct angle. In drill and blast excavation this is simple, but in TBM projects it has repeatedly turned out to be difficult. More than once owners have accepted bids containing reassurance from the contractor that the drilling method will be sorted out later. Experience shows that if ælaterÆ means after start of the TBM operation, it is often too late.

Jan 1, 1999

By F Owusu-Mensah, F Nsarko

The Obuasi Mine has been in operation for the past 100 years. Within this period a host of mining methods have been employed during its various changing phases. The causes for the changes are multiple, ranging from orebody capability, dynamics, technology, safety, economics, production levels, geotechnical, etc. Mining methods applied have also ranged from timber square setts, conventional cut-and-fill, shrinkage stoping, sublevel caving, mechanised cut-and-fill, longitudinal and transverse open stoping, and lately longitudinal retreat mining method (LRMM).The Obuasi Mine has a world class underground resource potential of about 27 million ounces. A third of this is in reserve. The orebody is subvertical, with multiple lodes and with widths ranging from 1.5 - 40 m. It stretches along 8.5 km N/S strike. A cursory statistical analysis on the various resource ore widths show a higher percentage (60 per cent) of the resource being within the range of about 1.5 - 10 m. Thus a high proportion of the resource is amenable to narrow vein mining methods. This has enhanced the choice of LRMM as an alternative method. Also, with the increasing cost of mining over time, LRMM, which eliminates expensive and time consuming footwall drives, will become far more advantageous as compared to the transverse/longitudinal open stoping methods which currently constitute about 40 per cent of the total underground production.The LRMM currently delivers about 20 per cent of the Obuasi Mine production. Plans are underway to improve total underground production from the current average of 160 000 tpm to about >180 000 tpm in the next few years and about 20 - 40 per cent more in the foreseeable future. Recoverable ounces will also increase from 26 000 to about 34 000 ounces per month. The proportion of LRMM in the business plan is also expected to increase from the current modest level to about 50 per cent. Despite its tremendous advantages in terms of economics and productivity, the method is facing some challenges during its inception. The objective of this paper is to highlight some of the emerging challenges and their effect on production and offer possible remedies that could mitigate the current and possible future challenges.CITATION:Nsarko, F and Owusu-Mensah, F, 2012. The Obuasi mine - longitudinal retreat mining method application and challenges, in Proceedings Narrow Vein Mining 2012 , pp 59-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

A feasibility study will fail its objective if it does not identify and then correctly assess, all the risks which could have a substantial impact on the financial viability of a project. Before this assessment can be undertaken, one needs to understand the risk profile of the entity which is making the decision about the project. Some of the commonly encountered issues when assessing project risk are related to the problem of not being able to see the wood for the trees. In any risk analysis it is important that conservatism does not strangle a viable project; that the variables are internally consistent with each other, that reality checks are carried out and that appropriate expertise is used. Sensitivity analysis forms a part of the overall project risk assessment; however, it can only test those variables which have already been identified in the financial model. The most useful tool in performing a sensitivity analysis is Monte Carlo simulation. When properly used, it provides a more real world scenario than the simple adjustment of key variables by ¦ 10 per cent one at a time. Monte Carlo can provide valuable information about the robustness of a project. Project risk and sensitivity assessment is prone to the analysis paralysis syndrome. The focus should be on quality rather than quantity.

Jan 1, 1997

By R Higashi, D Maruoka, T Murakami, Y Iwami

The ironmaking industry consumes a large amount of fossil fuel derived carbon as heat source, reducing agent of iron ores and carburising agent of reduced iron. Although the demand for drastic decrease of carbon dioxide emission, carbon is an essential element for smelting process of molten iron. The carbon recycling ironmaking process by circulating CO has been already proposed to achieve carbon neutrality. However, the production of molten hot metal is not considered in this process because sufficient amount of carbon does not dissolve in reduced iron by CO. Therefore, our group has suggested a new carbon recycling ironmaking process which can produce hot metal. In this process, free carbon and iron carbides produced by carbon deposition reaction using metallic iron as a catalyst are used. It is known that only Fe3C is obtained as iron carbide by using CO gas, however, Fe5C2 is also produced by adding H2 gas. The composite agglomerated with these carbonaceous materials and fine iron ore (Deposited Carbon-Iron oxide Composite: DCIC) is reduced and melted in a furnace. It is reported that Fe3C in DCIC accelerates the reduction reaction and melting of the composite. In this study, the effects of iron carbides and free carbon on the melting behaviour of DCIC are investigated. Fe3C, Fe5C2 and free carbon were produced by vapour deposition using porous iron whiskers and CO-CO2-H2 gas. These were agglomerated with hematite reagent at a certain ratio to prepare DCIC samples with and without Fe5C2. The samples were heated up to 1300°C in inert atmosphere. The DCIC containing Fe5C2 completely melted and iron nuggets were obtained after the experiment. This behaviour was not observed in the composite without Fe5C2. This indicates that using Fe5C2 is more preferable than Fe3C for molten iron production using DCIC.

Jun 19, 2024

Two characteristics of the modern mining industry are that there is a skill shortage and that young professional people rise rapidly into highly responsible supervisory positions. With this responsibility comes the burden of identifying and managing health and safety risks. Without the benefit of a comprehensive health and safety training program, these young professionals may be putting both themselves and those under their supervision at risk. The Moura Mine explosions and the asbestos health disaster should not be just artifacts of history, but highly valued lessons that impress the need for comprehensive health and safety risk management strategies on young professionals. From the perspective of the former secretary of the Committee to implement the findings of the Moura (Disaster) Inquiry and as the former coordinator of the Coal Workers Health Scheme, key issues in occupational health and safety management systems are explored.

Jan 1, 2005

By A C. Robertson

World urban expansion puts constraints on the available land surface area of our major cities both for accommodating people as well as providing infrastructure and services whilst at the same time attempting to preserve the remaining natural environment. Whilst consideration is often given to underground planning for private and public transport infrastructure, the author is of the opinion that the current lack of underground planning of our cities that are suitable for underground development will have major long implications when finally the need for underground space planning is critical and ultimately recognised. This paper identifies the need for our city planners to integrate surface planning and underground planning as a ‘total planning solution’ where the city plan incorporates the elements of underground space planning as identified in this paper. Investigations by the author reveal that there are very few cities in the world that actually incorporate underground space planning in their city plans. The author uses the City of Brisbane as a case study for the potential introduction of underground space planning as part of the city plan. Despite efforts by the author to include the planning concept of underground commercial development in the latest Brisbane City Plan 2014 as well as four underground space workshops in Brisbane over the past 20 year through the Australasian Tunnelling Society (ATS), underground space planning for the City of Brisbane, apart from infrastructure projects, is not considered of significance to the City of Brisbane.CITATION:Robertson, A C, 2014. Commercial underground space – planned development for the future, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 513–518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M Hassall, E Humphries

Personal risk assessment processes, also known as Take 5 or SLAM (Stop, Look, Assess, Manage) have been utilised in high hazard industries for over 30 years. However, there is limited research to understand if a personal risk assessment process improves safety and health outcomes. The author’s learnings during discussions with training participants in G3/G-MIRM (Risk Management Systems) and G2 (Risk Assessment for Supervisors) courses have provided them with significant insight into understanding if a personal risk assessment process is valued across a number of mining industry organisations. These discussions arise when the four-layer model is presented (Figure 1) where ‘Layer 4’ represents the last resort risk checking activity. In this context, training participants agree that this process has value. However, the consistent opinion is that the personal risk assessment process is not effective, that it is a ‘tick and flick exercise’ and is not achieving the desired outcomes.

Apr 16, 2024