Search Documents

By Dawson CF

About 17% of the world's present day oil supplies comes from wells drilled in the continental shelf of some 28 countries. The demand for oil is increasing each year and is expected to quintuple in the next decade. In the same period, the demand for gas will climb to at least 20 times its present rate. In the next decade, the percentage of oil and gas obtained from offshore is expected to rise to nearly half the world's consumption. The offshore oil industry is currently striving to achieve new technological advances in the field of deep ocean operations, especially in face of adverse seas. While the emphasis was put on drilling vessels for exploration, the industry was slow in developing effective offshore construction vessels. Until a year ago, construction vessels were but large barges with construction equipment mounted on their decks. These vessels all shared the same severe limitation: When the sea exceeds a five-foot wave height (and in some cases as little as three feet) the conventional construction barge is forced to suspend operations. In face of an oncoming storm they must run for shelter. Their utilization, therefore, is limited and in rough weather areas, such as the North Sea or the Bass Strait is lower than 50%.

Jan 1, 1970

By D Trembath

"One of the key risks to the success of a mining operation is the accuracy of the estimates of both the economic mineral and any accompanying contaminants contained within the ore reserve. Misrepresenting the mineralogical characteristics of the ore reserve can result in considerable financial investment in an operation that is in fact uneconomic and/or carries a significant environmental risk. This in turn can result in an unplanned closure of the operation with associated financial, environmental and social legacy. One way to minimise this risk is to undertake high density resource sampling to gain a better understanding of the resource characteristics. However, such an approach is expensive, time-consuming and often impractical. The risk of not having an accurate model is typically assessed during a feasibility study utilising a Monte Carlo simulation method or some form of sensitivity analysis. Importantly, the error margins used in these types of analyses are often based on subjective or very general criteria such as ‘professional judgement’ or an ‘industry standard’. This presentation introduces a conditional simulation method for developing a range of mineralogical distribution models. Based broadly on the method outlined in Journel and Kyriakidis (2004) the proposed approach develops this work further. It combines a geostatistical analysis of the available data with automated mine design software to provide a rigorous method for assessing the confidence in the mineralogical characterisation of the ore reserve. The process is based on simulating possible mine plans based on the statistical characteristics of the available resource sample data. These plans are then assessed against high resolution resource models generated using a Sequential Gaussian Simulation method. The outcome is confidence intervals for important characteristics of the ore reserve estimate relative to the actual resource. These confidence intervals are an objective and transparent measure important for assessing closure risks and represent an improvement over common practice.CITATION:Trembath, D, 2016. A simulation approach for improving the assessment of closure risks, in Proceedings Life-of-Mine 2016 Conference , pp 36–38 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By A Hocking, S Henderson

Commonwealth of Australia (2016) defines rehabilitation as comprising “the design and construction of landforms as well as the establishment of sustainable ecosystems or alternative vegetation, depending upon the desired post-operational land use”. For open cut coal mines in Queensland and New South Wales, the question of how to apply this intent to pits at mine closure is repeated for hundreds of individual pits. In EISs, closure plans and public discussion, assorted treatments are proposed to rehabilitate pits. While some aspects of final voids have been intensively studied, there is little guidance on how to choose a final void treatment option that delivers the optimal outcome against rehabilitation goals. For example, in the Bowen Basin and Hunter Valley commonly proposed rehabilitation actions include reducing the angles of pit walls; however, with few voids successfully rehabilitated to date there is limited understanding of what different wall slopes will achieve.CITATION:Henderson, S and Hocking, A, 2018. A decision framework for comparison of coal void rehabilitation options, in Proceedings Life-of-Mine 2018, pp 127–130 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By J L. Merritt

Contour banks and waterways are standard soil conservation measures to assist farmers reduce the impact of gully erosion on sloping cropping land by reducing the slope length to the interval between the banks. The Universal Soil Loss Equation (USLE) developed by the USA Department of Agriculture Soil Conservation Service in 1930s predicts the long-term average annual soil loss (A).The equation is the product of the rainfall erosivity factor (R), the soil erodibility factor (K), the topographic factors of slope length and angle (L and S) and the cropping management factors (C and P). Contour banks reduce the slope length (L) only.Contour banks are a constructed earth embankment, incorporating a channel on the upslope side, typically traversing a slope on or close to the contour to control and/or prevent the erosion of that slope. The banks are also referred to as graded banks, terraces, or bunds (DSITI 2015). Contour banks are either broad based or narrow based. Broad based banks allow the passage of the machinery over the banks whilst narrow based bank batters are too steep preventing the passage of machinery. Waterways are a stable, longitudinally sloping water disposal area of sufficient capacity used to discharge surplus runoff from the contour bank and to allow it to flow to a lower level without causing erosion (DSITI 2015).The mining industry must decide what the role for contour banks and waterways is in each operation’s rehabilitation and closure plan.CITATION:Merritt, J L, 2018. Contour banks in spoil rehabilitation – a matter of timing, in Proceedings Life-of-Mine 2018, pp 147–149 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Kuruppu M

Geotechnical design plays a key role in mine design. A proper geotechnical design provides a safe working environment and facilitates efficient mining operation. There are mainly three design approaches: (i) judgmental, based on observational and experiential facts, (ii) empirical, based on empirical design formulae; and (iii) analytical, incorporating numerical analysis. Most design applications are based on the design methods one and two as mentioned earlier. However, complexities arise in deep underground mining operations and deep open pit mines. These complexities and difficult geological environment introduce more uncertainties and simple empirical formulae would not be adequate as a design tool. These situations require numerical modelling and analysis of the design problems including interpretation of the results obtained from the analysis. There are several tools available for performing the numerical modelling and analysis. A brief review of the available tools is provided. The authors selected ANSYS (a general purpose finite element analysis tool) for use in mining geomechanics and geotechnical design. This paper includes several examples demonstrating the applicability of this software in designing mining structures. The authors hope that the design examples will demonstrate the use of the numerical modelling and analysis applications in excavation design.

Jan 1, 1995

By T Perera, B Fan, S Thang, T Hsia

The mining industry is currently focusing to develop and adopt sustainable collector chemistry that can efficiently recover valuable minerals from their natural state. However, a limited number of research can be seen on the design and synthesis of polymeric flotation collectors. The focal objective of this research is to synthesise a more effective polymeric collector with advanced architecture to utilise in the mineral processing industry. Reversible Addition-Fragmentation Chain Transfer (RAFT) co-polymers with cardanol derivatives have the potential to selectively trap valuable metals in the flotation process in a more efficient way. Cardanol exhibits amenability to chemical modification for making tailor-made monomers that can further produce polymers with high value. The synthesis of a series of fit for purpose copolymers in this study was accomplished by RAFT polymerisation. The ability to design complex architecture is a significant advantage in engineering polymeric collectors by RAFT polymerisation. Initially, commercially available cardanol was converted to a cardanol based monomer and copolymerised with commercially available monomers to synthesise a series of novel cardanol based copolymers with predetermined molecular weights. The side groups of the copolymer were chemically modified to incorporate functionality that can be selectively adsorbed on the chalcopyrite surface.

Aug 24, 2022

By Sen G

An amount of explosives, whether it be cylindrical, spherical, etc in configuration, with a hollow cavity in one face or end is known as a hollow or shaped charge. When this charge is initiated, a focussing of explosive energy will occur within this cavity. This focussing, or concentration of detonation products creates an intense localised force greater than just the simple detonation of a conventional explosive, (without a hollow cavity). If this hollow cavity explosive is directed against a target material this concentrated force is capable of creating a deeper penetration than the same amount of explosive without the hollow cavity. If a metallic liner material is used in the hollow cavity, upon detonation of the explosive this liner will form into a high velocity penetrating jet. Depending on the explosive type and the liner material's configuration the jet tip can travel up to 10 km/s. Linear shaped charges were developed using the abovementioned shaped charge concept but instead of being formed about an axis, they are elongated and constructed along the principal axis. Therefore instead of creating a narrow circular penetration jet, it forms a thicker planar cutting jet ideal for linear cutting purposes. Using Linear Shaped Charges (LSC) for pre-splitting is expected to result in more accurate directional fracture propagation, while minimising lateral micro fractures in the surrounding rock mass which is required to remain undamaged.

Jan 1, 1995

By E Holloway

The optimisation of an open pit mine can be broadly split into two stages, the first being the ultimate pit optimisation (and subsequent stage designs), and the second being schedule optimisation. Macroeconomic uncertainty clearly impacts on both however interrelationships do also exist. Generally, the opportunity exists for the ultimate pit to be revised during each planning cycle, however when this reprieve is removed the uncertainty for the underlying business increases. As one example, the introduction of an in-pit waste dump can be seen to significantly limit the option to revise the ultimate pit. When in this situation there are two potential risks that present: (i) the long-term price used for the ultimate pit selection is optimistic, and too large of a pit is selected resulting in waste being mined which uncovers material not of a significant value to deliver a profit; (ii) the long-term price used for the ultimate pit selection is pessimistic, too small of an ultimate pit is selected, and ore of realisable economic value left behind. Both of these outcomes are risks and as such can be assessed and quantified. CITATION: Holloway, E, 2018. Incorporating economic variability into a strategic planning framework, in Proceedings Complex Orebodies Conference 2018, pp 88–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By J E. Everett

Maximising ore tonnage at a selected target grade requires that appropriate ore identification criteria be established. Iron ore mining block models may consist of many millions of estimated blocks, each block corresponding to the selective mining unit (SMU), with grade interpolated from drill hole data. Each block can be considered as a potential ore candidate. Analysis of such a huge database can require large computational resources, especially for sensitivity analysis requiring multiple computations. However, an alternative streamlined approach is possible, where the data are compressed to an appropriately smaller and representative subset. The consequent data reduction not only makes it feasible to consider the simultaneous analysis of multiple pits but also considerably speeds up computation, enabling sensitivity analysis of the potential ore tonnage as a function of the required grade. Ore identification criteria can be successfully established using appropriately chosen reduced data comprising less than one per cent of the blocks. The ore identified is virtually indistinguishable in tonnage and grade from the ore that would be selected using the entire block model.Two methods of data reduction are tested: sampling (using a proportion of unaltered blocks) and binning (consolidating groups of blocks to a single average grade). The source blocks are first sorted (such as by location, analyte grade, principal component score, random order or value) before sampling or binning. In this study, the sorting options considered were by location and Fe grade. The effectiveness of each method was evaluated using the block model subsets to select the maximum tonnage of ore at a specified target grade. Block model data from an anonymous Pilbara iron ore project with about one million blocks averaging 1.132 kt were used. The blocks are from multiple resource models, to be blended to a single product. Sampling is shown to be superior to binning because sampling preserves the full variability while binning, although matching the mean block grades reduces their variability.It was found that the appropriately sampled data sets (sorted by location) gave results virtually identical to the results for the full data set, even when the samples comprised less than one per cent of the original blocks. The reduction in computer time to identify maximum tonnage at a specified grade was approximately proportional to the sample percentage. The increase in computation speed greatly facilitated sensitivity analysis. A sampled data set of one-eighth the total block model was used to investigate the effects of changing each of the component grades around the original grade specification. The results of this sensitivity analysis are discussed, and illustrate the potential benefit of carrying out sensitivity analysis in determining feasible and marketable product grades.CITATION:Everett, J E, 2015. Block model data reduction and sensitivity analysis, in Proceedings Iron Ore 2015, pp 263–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Variety among deserts is nearly as great as among other climatic environments. Common to most deserts, and to areas downwind from them, is the dominance of aeolian transport of surface material, at least during some seasons of the year. The result is dilution of local surface materials with varying proportions of chemically uniform fine sand and silt, often imported by the wind from remote areas. Fortunately, desert pavement,.even though separated from bedrock by a meter or more of nearly pure loess, is simply a diluted reflection of nearby bedrock. Infiltration of loess through the surface debris and the rudimentary soil-forming processes in the desert usually preserve the integrity of the pavement. This pavement, or its "downstream" derivatives, provides a suitable sample for exploration geochemistry if proper care is taken to circumvent the aeolian dilution. The simplest and most commonly used method of circumventing the dilution is to use a coarse fraction of soils or stream sediments, discarding or retaining the finer fraction depending upon the magnitude of the dilution. Where the coarse surface debris is composed of rock chips representative of the bedrock sources, the method is successful. Under most circumstances the coarse fraction of the surface material will give a fair representation of gross lithology and will occasionally give an indication of mineral- ization. The major drawback to this approach is that selective weathering and erosion in the vicinity of mineral deposits often lead to the loss of ore minerals into the finer fraction, leaving a coarse residue enriched in feldspar and particularly in quartz; thus, the geochemical signature from a mineral deposit is effectively reduced or completely masked. The second most commonly used method to overcome aeolian dilution, and probably the most effective at present, is to use a heavy- mineral concentrate. This approach presupposes that the chemical signature sought resides in a heavy mineral. Fortunately, the arid weathering cycle is conducive to the formation of a wide variety of secondary ore

Jan 1, 1988

Since gold was first discovered, mining development in the West Australian goldfields has been heavily dependent on the location of groundwater both for potable and mineral processing supplies . The location of adequate and economic sources of water has been a constant challenge to both explorers and developers throughout the history of the goldfields. The provision of a piped supply from Mundaring in 1903 greatly alleviated pressure on scarce resources, lowered mining costs and permitted the orderly development of infrastructure. However, increases in the demand for water resulting from new mineral discoveries over the past three decades has led to renewed pressures for more local supplies to be established. Wide-ranging groundwater exploration took place in the late 1960's and early 1970's, also, more recently, in support of intensified gold exploration. The collation and interpretation of the hydrogeological data from the whole goldfields region indicates that despite a low mean annual rainfall of between 180 and 350 mm, quite marked differences exist between the rates of groundwater recharge in different parts of the area, In general, these can be shown to diminish in a southerly direction contrary to a trend towards increases in annual rainfall. Recharge rates are related mainly to differences in rock weathering pattern, geological structure and physiography. The same differences have controlled the pattern of groundwater salinity and the magnitude of groundwater storages associated with the palaeodrainages. In the vicinity of the northern and western watersheds with the Gascoyne, the superficial sediments tend to be thin, may have calcrete in the section and contain moderate storages of brackish or even fresh water. This contrasts with the lower regions of the palaeodrainages where calcrete is absent and deeper erosion has permitted the accumulation of relatively large thicknesses of fine-grained sediments which are saturated with hypersaline water and constitute substantial storages. Account must be taken of these characteristics if water supply sources are to be optimised to meet the growing demands for groundwater in the region.

Jan 1, 1988

By J Rayo

Andean countries (Chile, Peru, Bolivia and Argentina) have 42 semi-autogenous mills (SAG) in operation and there are more than 30 projects in the pipeline that consider SAG mills. At the end of the next decade, the total amount of SAG mills in this area will likely be close to 100.There is a lot of reliable operational information collected by JRI Ingenieria Sociedad Anonima, the author’s engineering company, for more than 20 years and processed by statistical software, to be used as a reference for design basis of future projects or to improve operations by comparison. JRI Ingenieria Sociedad Anonima has reliable information related to the performance of more than 50 per cent of the Andean SAG plants.The paper presented considers a set of graphs that summarise the collected and verified SAG plants technical data. The figures will show key parameters as circuits and equipment data, energy consumption, technical availability, utilisation rates, throughput variability, pebble productions, steel consumption and others.The data is compared with typical design basis of several engineering companies and the main differences are analysed and/or commented on.CITATION:Rayo, J, 2014. Comparison of semi-autogenous mills operations in Andean countries, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 283–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By B Taylor

The Perseverance deposit is the most southerly known economic copper/gold deposit within the Cobar gold field. The deposit is situated approximately 12 km to the south-southeast of Cobar and is essentially blind to surface with the top of economic mineralisation occurring 750 m below ground level.Based on the December 2010 resource estimate (inclusive of reserves and net of depletion) the deposit contains 3 011 000 tonnes at 6.1 g/t Au and 0.90 per cent Cu (590 000 oz of gold and 28 000 tonnes of copper). The deposit is comprised of four principal lenses, the Perseverance, Hulk, Zone B, and Hercules lenses. In excess of 90 per cent of the known resource tonnes are contained within the Perseverance and Hulk lenses. The deposit is shear related and hosted within lower Devonian rocks of the Cobar Basin. The competency contrast of rhyolites juxtaposed against sediments by the Peak-Perseverance shear is the principal control on mineralisation. Both the Perseverance and Hulk lenses are primarily hosted by brecciated rhyolites juxtaposed against Chesney formation sediments across the Peak-Perseverance shear. This faulted rhyolite sediment contact roughly defines the global orientation of the deposit. The Perseverance lens continues within the shear for up to several hundred metres beyond the extent of the faulted rhyolite sediment contact. Mineralisation within the shear beyond the faulted rhyolite contact zone is hosted by sheared silicified sediments. The Perseverance lens remains open at depth and to the south.The Zone B and Hercules lenses, which are significantly less important in tonnage terms, are hosted by rhyolite breccias within the main body of the rhyolite and appear to be only tenuously related to the Peak-Perseverance shear. Within the Perseverance lens, the presence of northeast trending high grade breccia veins developed oblique to the north-south trending shear system has led to the development of steeply north plunging high grade ore shoots within a globally north-south trending mineralised domain. These high grade shoots have limited horizontal continuity but significant down plunge extent.The presence of coarse gold and the resulting strongly skewed nature of the gold grades, in conjunction with controls on mineralisation which are not parallel to the mineralised domain, has led to predictive difficulties regarding stope performance.Strong heterogeneity of the gold content of the ore and geological controls on mineralisation which are not parallel to the global trend of the mineralisation impose a set of difficulties which sound geological control is helping overcome.

Aug 22, 2011

Porphyry type mineralization of Lower Cretaceous age in eastern Queensland has been recognized only from the easternmost part of the northern New England Orogen (Day, Murray and Whitaker, 1978), within the northern Yarrol Province (Horton,1982). Recent work about the Mt. Suthers (Pb, Zn, Ag, Cu, Au), Lug-e-nor (Cu, Pb, Zn, Ag, Au, Mo), and German Tully (Cu, Au, Bi) prospects suggest that there has been a phase of porphyry type mineralization within the Gympie Province, of Lower Cretaceous age, overprinting earlier Permo-Triassic phases. About the Mt. Suthers Prospect surface samples of shallow, medium to heavy textured soils derived from marine sedimentary rocks of Permian age, and extrusive and intrusive igneous rocks of intermediate composition and Triassic age, were analysed for Cu, Zn, Pb, Co, Cr, Ni, Fe, V, Mn and Ag. Whereas strong iithological control determined the distribu- tion of Cu (diorite) and of Cr, Ni, Fe and V ,sedimentary rocks), the distribution of Pb, Zn, Ag and of Cu, were determined by mineralization of faults by a cavity fill hydrothermal process. Gold is associated with the Pb, Zn, Ag mineralization. Co and Mn showed distributions independent of lithology and structure. The fault controlled style of mineraliz- ation at Mt. Suthers is repeated at other localities to the south; Calgoa, Marodian, and German Gully. Relative dating of structural features and isotopic dating of nornblende porphyrites (134-135 m.y.) near and related to those mineralized at German c;ully suggest a previously unrecognized phase of porphyry copper style mineralization in south-east Queensland of Lower Cretaceous age (Fig. 1).

Jan 1, 1987

By D-J Min

Strategies and achievements in the Asian steel industry to construct industrial ecological chain are reviewed largely in the case of Japan, Korea and China. Emphasis is placed on the development of resource circulatory system for the minimisation of various wastes and emissions of green house gases (GHG), toxic gases and polluting particulates. The minimisation includes:Rationalisation of iron and steelmaking processes; Implementation of available relevant measures/technologies; Life cycle assessment in designing steel from semis to assembled products; Reduction, reuse and recycling of materials and energies; and Utilisation of core competence technologies to process domestic and industrial wastes. In view of global nature of the above wastes- and emission-issues, inter-industrial linkage and international cooperation across the borders in the Asian countries have become more important. Inter-industrial linkage definitely serves to cut back the wastes and emissions. Examples of such linkage and factors influencing the sustainability of the linkage are described with expectation for further development of the linkage. Importance of international cooperation cannot be overstressed under the circumstances where steel production in China exceeded 220 Mt and world production exceeded 945 Mt in 2003 and is still increasing. Practical measures are discussed to enhance the linkage and cooperation for effectively promoting the reduction, reuse and recycling, including implications for the nonferrous industry.

Jan 1, 2004

Declines for both access and rock haulage are replacing shafts for mining relatively shallow deposits of down to 1000 m below surface. Where the orebody does not outcrop and where surface access may be restricted, it is often necessary to drive long dead end headings before a connection can be made back to surface and a ventilation circuit created. In hot tropical areas and where large diesel powered equipment is used for mining, heat may also be a problem at these relatively shallow depths. The normal design criteria based on statutory limits and good practice used to evaluate ventilation and cooling requirements in terms of air velocity, dust, gases, diesel exhaust dilution, re-entry after blasting and heat stress are described in this paper. These are then used to design and cost alternative auxiliary ventilation systems that include leakage based on general fan performance curves and typical duct systems. The implications of the current European Community recommendations regarding nitrous fumes are also briefly considered. The actual problem relates to a 2100 m long decline that may have to be extended to 3000 m long without a connection to surface or through ventilation and is located in a hot tropical area where the surface wet bulb temperatures may exceed 25¦C for more than a third of the summer period. Once the preliminary ventilation design is completed, the auxiliary ventilation system can be modelled and simulations undertaken that incorporate heat and moisture transfer routines with the objective of determining the cooling load and amount of refrigeration required. Cognisance is taken of cyclic diesel operations and the thermal flywheel effect of the surrounding rock on the wet and dry bulb temperatures resulting from these operations.A suitable modular cooling system located at the portal is described and optimised with capital and operating costs of both the ventilation and cooling systems provided.

Jan 1, 2005

By A Woodley, N C. Kunz

A mine site water balance is important for communicating information to interested stakeholders, for reporting on water performance and for anticipating and mitigating water-related risks through water use/demand forecasting. Gaining accuracy over the water balance is therefore crucial for sites to achieve best practice water management and to maintain their social license to operate. For sites that are located in high rainfall environments the water received to storage dams through run-off can represent a large proportion of the overall inputs to site; inaccuracies in these flows can therefore lead to inaccuracies in the overall site water balance.Hydrological models that estimate run-off flows are often incorporated into simulation models used for water use/demand forecasting. The Australian Water Balance Model (AWBM) is one example that has been widely applied in the Australian context. However, the calibration of AWBM in a mining context can be challenging. Through a detailed case study, we outline an approach that was used to calibrate and validate AWBM at a mine site. Commencing with a data set of monitored dam levels, a mass balance approach was used to generate an observed run-off sequence. By incorporating a portion of this observed data set into the calibration routine, we achieved a closer fit between the observed versus simulated data set compared with the base case. We conclude by highlighting opportunities for future research to improve the calibration fit through improving the quality of the input data set. This will ultimately lead to better models for run-off prediction and thereby improve the accuracy of mine site water balances.CITATION:Kunz, N C and Woodley, A, 2013. Improving the accuracy of mine site water balances through improved estimation of run-off volumes, in Proceedings Water in Mining 2013 , pp 267-272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By M J. Pejovic, S BoÜevski, I Miljanovic, M Hudej, A Milutinovic, A Petrovski

The paper deals with the problem of managing the supplies of consumables (energy resources, lubricants, explosives, explosive supplies, tires, spare parts, etc) in mines. After the introductory remarks and comments, a general stochastic model of supply, relating in general to the dynamic programming method is presented. A selection of stochastic supply model for experiments and research by the authors of this paper is not a coincidence, based on of their long experience, showing that this type of model is the most suitable to provide support for decision-making and management of supplies of consumables in mines.In order for the problem?of?consumables?supply?management to be reviewed, in whole and objectively from the aspect of risk, experimental tests of the stochastic model in real conditions were performed at the limestone open pit mine æZelenikovecÆ near Skopje, the capital of Macedonia. The scope of the experimental research enabled reliable analysis. The results obtained confirm the efficiency and reliability of the stochastic model and two separate manipulative-operational positions regarding its application, which may have an important influence on the optimisation of supplies.

Sep 26, 2011

By X Ma

Kaolinite is of very fine particle size in nature and thus its dispersion plays a key role in the successful removal of kaolinite in iron ore flotation and selective flocculation processes. As the most widely used dispersant in the world, sodium silicate has been used as a standard dispersant for kaolinite in the iron ore industry. However, the actual effect of sodium silicate on the colloid stability of kaolinite particles and its dispersion mechanism remain unknown in the literature. In this work, the dispersion effect and dispersion mechanisms of some common inorganic and organic dispersants, including sodium silicate, polyphosphate and a low molecular weight polyacrylic acid, on kaolinite particles were systematically investigated through electrophoretic mobility and colloidal stability studies over a wide pH range. It was found that sodium silicate-kaolinite interactions only take place in the neutral and acidic pH range, while polyacrylic acid and polyphosphate interact with kaolinite from pH 3 to 10.5. Consequently, sodium silicate only disperses kaolinite at neutral and acidic pH. In contrast, polyacrylic acid and polyphosphate disperse kaolinite from pH 3 to 10.5, with strong dispersion effect observed at neutral and acidic pH. In the iron ore industry, selective fl occulation and reverse cationic fl otation, the most widely used flotation route, are both conducted at pH 10 to 10.5. The results of the present study show that, at such high pH, polyacrylic acid and polyphosphate are more effective dispersants of kaolinite, in comparison with sodium silicate.

Jul 11, 2011

By V Gupta, Z Huang, S K. Biswal

G-Cell is a new design modification of the Imhoflot pneumatic flotation technology, which utilises a self-inducing aerator inside a downcomer, where bubble-particle attachment takes place. The present study has investigated the suitability of the G-Cell technology for cleaning fine coal using a 0.8 m diameter prototype unit at a coal preparation plant operating in the Midwestern United States. A slip-stream obtained from the overflow of raw coal cyclones operating in the plant, containing nominally minus 150 micron size particles and having ash content in the range of 40 per cent to 50 per cent and sulfur content in the range of 1.30 per cent to 1.50 per cent, has been used as the feed for the G-Cell. The performance data produced from the G-Cell tests are found to be very close to the ideal performance curves produced from release analysis. A statistically designed experimental program has been conducted to investigate the parametric effects on various key process responses, such as combustible recovery, product ash and sulfur rejection. The empirical models developed in this study have been utilised to identify a suitable experimental region for achieving a desired combination of response targets.

Jan 1, 2005