Search Documents

By Fernando N, Guang LX

Brown coal in Victoria in spite of its substantial reserves is not utilized greatly because of its high moisture content(-65% w/w). Transportation and handling costs of raw brown coal, on an available energy basis are so expensive that 93% of production is burnt for electricity generation on or adjacent to the coal deposit in Victoria. With direct firing of moist brown coal in power stations, approximately 20% of the gross calorific value of the fuse is used to evaporate the water contained in the coal. This energy is lost as vapour with the flue gas which is vented to the atmosphere. Also there is a 25% increase in flue gas volume and the size and cost of most of the units through which it passes must be appropriately larger. Since there are large quantities of water present the flame temperature is significantly reduced. For zero excess air and no air pre-heating the theoretical flame temperatures are: 609'o wow moisture 1450¦C 40% ª ª ª 1790¦C ZOO ª ª ª 1990¦C As a result of this there is a reduction in radiant heat transfer leading to a requirement for a two fold increase in radiant tube area. A boiler of much greater size and cost is thus required to house the additional tubes. Figure 1 illustrates the relative sizes of a boiler fired with 60% moisture brown coal with a boiler or similar output fed with a British bituminous coal, 14% moisture.

Jan 1, 1989

Commencing from a platform acknowledging the capability of the Russian mining industry in open cut and underground mining operations a revitalisation of the industry will depend on an assimilation of mining economics and on an opportunity for technical training of Russian mining industry professionals.Successful foreign investment in parallel with the reconstruction of the industry rests on an understanding of culture, history, internal controls under central planning, and external factors affecting mining development.

Jan 1, 1997

Distillation of the large and growing greenhouse literature indicates that: ò Global warming has occurred over the past century or more; ò Build-up of CO2 (and lesser greenhouse gases) in the atmosphere is a fact; ò This build-up is likely to cause further global warming. It does not appear possible to conclude that the observed C02 build up and observed global warming are linked; nor is it yet possible to forecast global or regional climate variation with conviction. The dominant greenhouse gas is C02 with about half the warming potential of those gases emitted by man's activities; and about 80% of anthropogenic C02 emissions are from the burning of fossil fuels. Fossil-fuel C02 emissions arg divided about equally between the developed countries of OECD and the rest of the world. However C02 output growth over the past decade was about 4% for OECD and some 40% elsewhere. Population growth and pressure for better living standards will ensure continued higher growth outside OECD. Uncertainty about the impact of increasing C02 emissions on climate, and the long lead-times involved in limiting the increase in atmospheric C02 concentrations, are good reasons for taking action now. Australia accounts for about 275 million tonnes a year or just over 1% of the CO2 emitted from the world's consumption of fossil fuels, and the fight to control global emissions will be won or lost elsewhere. Australia's participation will be by wise conselt and by example. In view of the uncertainties involved, it appears premature to take actions that might place an additional financial burden on our hard-pressed country. However, much can be done now that makes good economic sense and has the added benefit of limiting the growth in Australia's CO2 emissions. Natural gas emits less C02 per unit of energy when burned than either coal or oil. Furthermore, new gas-fired power stations utilise energy at considerably higher efficiency than is the case today with coal or oil. Because of much lower capital costs, there is a compelling economic case for permitting natural gas to compete freely with coal in the Australian power generation market.

Jan 1, 1989

By Beattie T

For many years explosive sensitized explosives were assessed using the ballistic mortar. The standard test used lOg of explo- sive initiated with a detonator. Over the past 30 years many non- explosive sensitized explosives and blasting agents have been developed. Most of these new explosives and blasting agents cannot be tested in the ballistic mortar as they are not initiated by a detonator. It is also known that all explosives have a criti- cal diameter. When the cartridge diameter is less than the criti- cal diameter a stable detonation cannot be produced and the explosive fails to propagate. For many blasting agents the criti- cal diameters are greater than 50mm and such large diameters cannot be tested in the ballistic mortar. The underwater test allows explosives to be tested in diameters greater than the critical diameter and to be adequately initiated with suitable boosters. The effects of the explosive on the water are easy to measure and the test provides a safe, convenient and reproducible means of assessing explosive performance. The reaction products are allowed to expand to a low final pressure. The underwater test can therefore be used to give a measure of the total expansion work of explosives. The detonation of an explosive induces a shock wave in the surrounding water. The profile of the shock wave can be meas- ured 3-6m from the charge and the energy in the shock wave cal- culated. Measurements over a range of distances show that the shock wave is attenuated as it travels through the water and the attenuation is different for each explosive. This makes it difficult to estimate the energy dissipated in the water between the charge and a single gauge. The reaction products continue to expand and displace water. The bubble continues to expand until the kinetic energy of the water is zero. The gas pressure in the bubble is now lower than the hydrostatic pressure and the bubble radius is a maximum. The higher external hyrdostatic pressure causes the bubble to implode. The bubble energy is the work done displacing the maxi- mum bubble volume against the hydrostatic pressure and can befound from the bubble period. It is not always easy to find a large enough pond for the bubble to expand undisturbed by the water surface and the containing boundaries. This makes it difficult to determine the bubble energy accurately in shallow Ponds.

Jan 1, 1988

By Lennox A

In an attempt to increase underground productivity Coal and Allied has introduced a continuous haulage unit into it's Moonee colliery. A second unit is planned for Nallarah colliery in the near future. Both systems will be roof mounted or monorail type and manufactured by Joy Manufacturing Pty Ltd. The introduction of these machines is seen as a logical step in improving the efficiency of mining with continuous miners. This could be in conjunction with longwall mining in the rapid development of gate roads or, as in the case with these machines, as conventional development and extraction units. The advantages of the continuous haulage system are; Relatively low cost. 2 Ability to obtain high productivity in irregular or disturbed coal reserves not suitable for longwall mining. 3 Increased worker safety with the elimination of shuttle cars and the majority of trailing cables. 4 Increased productivity independent of soft or difficult floor conditions. At the time of writing the Moonee installation is 6 months old. The Nallarah machine is due for delivery March 1988.

Jan 1, 1988

From statistics on general and electrical fatalities in the Australian mineral industry, it could be said that the present approach to industrial safety is irrational. Deaths are few and decreasing in number, yet spend- ing on occupational safety is large and increasing. State mine safety inspec- torates are being expanded and a National Occupational Health and Safety Commission was recently established. Recent data are analysed in the paper and mining industry fatalities placed in perspective with deaths in other areas. Cost effectiveness of different strategies is discussed along with social implications. Strategies found successful are described and others suggested.,

Jan 1, 1988

By Jensen B

The approach of using the Coward Triangle for the analysis of flammable mine gas mixtures has been examined for its application, to the flammability of coal dust/gas/air mixtures. Explosible lean limit and rich limit concentration data for dust/methane/air mixtures are examined and illustrated using co-ordinate geometry. It is concluded that a three-dimensional envelope representing hybrid explosible mixtures can be drawn. The dimensions of this explosive zone will vary with the characteristics of the coal dust and the gaseous composition of the mine atmosphere. Further research is needed to establish these dimensions for important mined seams.

Jan 1, 1994

By Bishop I, Toon S

To determine whether 130 felt earth tremors around Edwinstowe, Nottinghamshire U.M, which also experienced severe surface fissuring, were caused by coal extraction, a surface seismometer array was established around Thoresby Colliery. Over the next year, 785 microseismic events were detected. The spatio- temporal seismicity patterns are clearly associated with the commencement, continuing extraction and closure of faces. Of particular note are events which locate at the surface and appear to be related to the active fissuring. Events occur within days of commencement of production and cease when production finishes, with good correlation between face advance and hypocentral position. Naturally occurring microseismic events have also been detected up to 1 km ahead of active longwall faces in the Midlands using triaxial geophone packages grouted into the seam together with a surface seismometer in the top of the borehole. The quality of these data were very high and guided waves can clearly be seen with the dispersive characteristics associated with seam waves. In one experiment more than 2000 events were detected in only two days of monitoring even in a relatively noisy surface environment. This paper demonstrates how very accurate locations (5 10 metres) can be generated using three-component digital data from only one borehole. The surface seismometer and the borehole P-wave onset can give extra precision for the height of the event relative to the seam. The event distributions give a dynamic, three-dimensional image of the developing patterns of fracturing above, below and ahead of the longwall face with important implications for roof control, subsidence prediction and gas Migration.

Jan 1, 1992

The sulphide ores of the Kalgoorlie goldfield have long been looked upon as' refractory, involving special metallurgical treatment. For many years two kinds of treatment have been practised-(l) wet treatment, including fine grinding, amalgamation or concentration of the free gold, concentration of the sulphide minerals with subsequent roasting and cyanidation, and cyanidation or bromo-cyanidation of the residue from the concentrating operation; (2) dry-crushing of the ore and roasting the whole of thecrushed ore, amalgamation of the gold in the calcine during fine grading, followed by cyanidation. The wet treatment was advanced a stage further when, in 1929, the Lake View and Star Ltd. adopted large scale flotation. As a consequence, however, further metallurgical problems were introduced. This paper covers the investigation, ,of one of the most prominent of these problems.Flotation preceded by strakes was satisfactory to a point.The flotation concentrate consisted largely of auriferous pyrite and tellurides, and the gangue minerals in the concentrate were practically barren.Several sources of loss of gold values were, however, found to be associated with this circuit, viz.-(a) There was the loss of gold in the flotation tailing.(b) Loss by dusting during roasting of the flotation concentrate.(c) Loss of gold in the cyanided residue.

Jan 1, 1937

The medical evaluation of the health effects of dust exposure in the mining industry should be based on the premise that the results of the medical examinations will be considered in relation to the previous history of exposure to dust.(l) To this end the Mines Regulation Act and the Regulations under that Act in West- ern Australia provide for: the prime responsibility for dust sampling to rest with the mining companies; the appointment of a Ventilation officer by each mine and the sampling and record- ing by him of dust and toxic gases in work places at three monthly intervals, or more frequently as required; the appointment of a Mines Medical Officer who shall make provision for the medical examination of persons and the prevention of occupational diseases; the appointment of a Ventilation Board, consisting of the State Mining Engineer, the Senior Inspector of Mines for the State, an Inspector of Mines having specialised training in ventilation tech- nology, a medical practitioner having specialised experience in occupational health problems relevant to the mining industry, and a Scientific Officer having duties under the provisions of the Clean Air Act, 1964;

Jan 1, 1979

Mineral resource and ore reserve estimation is a challenging and demanding field, requiring application of professional knowledge, skill and experience of the highest order. If the many potential hazards and pitfalls are to be avoided however, there are two other requirements which are of equal, if not greater importance:

Jan 1, 1990

By D Dickson

The properties along Ida Avenue in Mosman stand 10 m above the road on an outcrop of Sydney sandstone. Access to the houses is generally via a long steep staircase. The owner of 22 Ida Avenue identified an opportunity to use the natural strength of the rock beneath his property to excavate an underground garage and to provide access to the basement of his property via a 10 m elevator shaft from the back of the garage. This paper will describe the design and construction of this unique and innovative urban development.

Jan 1, 2008

The Permian rocks at Gympie were first studied as far back as 1868 in conjunction with the discovery of gold. The relationship of the Gympie Group to other sequences in the Gympie Composite Terrane is an important subject of investigations in a new mapping project of the Geological Survey Program of the Department of Resource Industries.In two areas the Gympie Group has been divided into four defined formations. They are the Highbury Volcanics (base), Ram mutt Formation, South Curra Limestone and Tamaree Formation (top) in the Gympie area, and the Mant basalt (base), Kolbar Formation, Gigoomgan Limestone and Teebar Formation (top) in the Gigoomgan area. Geochemical and lithological evidence from the basal volcanics of the Gympie Group (Highbury Volcanics, Mant basalt) indicate that they developed in an intraoceanic island arc setting. The overlying volcaniclastic sediments (Rammutt Formation, Kolbar Formation), which contain some continentally-derived material, are mainly of local derivation and shallow-water marine. A hiatus is present at the top of the Early Permian Rammutt Formation and Kolbar Formation. Following the hiatus, limestone sedimentation characteristic of a basin of restricted circulation developed in the Late Permian. There is some evidence of a hiatus between the limestone deposition of the Gigoomgan and South Curra Limestones and the overlying probable turbidite deposits of the Teebar and Tamaree Pnrmatinnc

Jan 1, 1990

This paper has been prepared to challenge the thinking of new leaders entering the mining industry in two areas. First, what is the worldÆs perception of mining and what does this mean to those entering the industry? Second, what is the future of learning in the mining industry and how can the industry attract and retain the best people?Then in closing, how can mining companies turn these challenges into opportunities and specifically how is BHP Billiton meeting these challenges.

Jan 1, 2004

Vaal Reefs Mine annually produces some 75 tonnes of gold. Stoping operations, using a scattered mining method, are conducted on several reef horizons within Witwatersrand Supergroup metasediments of the Klerksdorp Goldfield. Current grades average 7.19 g/t Au over a 133cm stoping width. The reef horizons, of which the Vaal Reef is the most important, consists of 2.9Ga palaeoplacer deposits at the base of low angle unconformities. Typically, a reef comprises a mature quartz and chert conglomerate with a siliceous matrix and intergranular pyrite and carbon. Geologists are primarily responsible for underground mapping and supervising of drilling programs. To a lesser extent they are involved with sampling, grade control, ore reserve estimation, mine planning and rock mechanics. Due to a general decline in grades of gold mines, an escalation of production costs, and with the current weak gold price, it has become essential to improve production efficiencies. Consequently the role of the mine geologist has moved away from that of simply keeping the mining people "on reef'. Greater emphasis is being placed on refining geological models to assist in selective mining of the reef and investigations of secondary reef horizons are encouraged. Exploration within fault losses and re-evaluation of pillars is important, and geologists are becoming more involved with sampling and grade control exercises.

Jan 1, 1990

I.T.H. Drilling has been accepted as a tool used daily for both production and service work in Australian underground mines. For this reason, it is of interest to examine the rigs and drilling equipment in use to do this work, also to review the technique necessary to ensure that this drilling is done efficiently.

Jan 1, 1978

Workplace Centred Learning, (WCL), is a learning strategy which helps organisations cope with the constant change in skill requirements that is part of business today. WCL focusses on the specific needs of the workplace and provides the structure and sets the standard whereby the required competencies can be transferred between individuals. Learning is considered part of the job and ownership is achieved by involving individuals in all aspects of the learning system. Each individual in a WCL system is considered both a learner and a teacher. A significant advantage of WCL over conventional training systems is that it responds quickly to changing requirements, and once in place, becomes self-sustaining. That is, once implemented, the system provides mechanisms to detect and respond to changes in skill requirements as they arise. WCL is a competency-based system with multiple levels of validation. It provides a flexible approach to skills development that recognises both the needs of the workplace and the needs of the individual. WCL was developed in collaboration with ALCAN Aust Ltd and is currently being implemented by companies within Australia and overseas.

Jan 1, 1995

A field trial of the prompt neutron-gamma SIROLOG technique was undertaken by the CSIRO - Division of Geomechanics at Callide Coalfields during July 1989. The trial investigated whether the sonde could reliably be used for the determination of Ash and Iron Oxide (Fe2O3) in coal seams, which had a highly variable iron content. Ten boreholes were logged, being water filled of a nominal diameter of 120 mm. The logging probe employed a 1.6 ¦g 252Cf neutron source and a 51 x 51 mm BGO detector. The source to detector distance was 15 cm. The results from one exploration borehole at the Dunn Creek Mine are discussed in the paper. The rms deviations for ash and iron determination between the neutron-capture predictions of the geophysical logs and the laboratory - chemical assays were 1.9 per cent Ash and 0.88 per cent Fe respectively. Using existing empirical equations which relate iron oxide concentration in coal ash to Initial Deformation Temperature (reducing conditions) at Callide, it may be possible to indirectly determine ash fusion properties as least as accurately, on a more detailed ply-by-ply basis, and more cost competitively than current laboratory techniques allow.

Jan 1, 1991

Some thirty ore minerals occur in the Mount Morgan orebody. Pyrite is the dominant mineral with chalcopyrite, magnetite and pyrrhotite major components. Gold and gold tellurides, in accessory amounts, are economic- ally important. The prevalence of volcanic rocks in the mine area and the presence of trace amounts of such minerals as cassiterite, gold, native bismuth and rutile suggest a voicanogenetic origin for the ore. The ore occurs in a breccia pipe which cuts through the volcanic and associated strata but the former existence of a syngenetic stratiform ore bed is evidenced by the presence of occasional masses of perfectly banded sulphide ore including a barite-rich "black shale" with sulphide layers exhibiting slump structures. Mineralization is thus both _ syngenetic and epigenetic. The orebody (breccia pipe) is intruded by small stock-like bodies of quartz latite which is believed to have been the upward rising magma invading the orebody of which it is the parent. This has resulted in the annealing recrystallization of the ore minerals and the quartzose gangue with a low strain rate due to magma drag and dilation during intrusion.

Jan 1, 1974

By Henley S

The year 2000 is not very far ahead - only five years. It should not be hard to forecast what will happen between now and then, because the technologies that will be in practical use then should all be at least in embryo existence now. There has been a historical trend for the mining industry to work ever more difficult and ever more marginal deposits. There are clearly a few exceptions and major discoveries, but the industry is becoming heavily dependent, at both the exploration and the mining stages, on technological innovation to retain acceptable profit margins. With the new exploration and mining technologies come requirements for additional computing support. Computing technology further allows the potential integration of a wide variety of different types of data to help the explorationist to build and test exploration strategies, or to help the miner to design and schedule mining operations.

Jan 1, 1995