Search Documents

By Bailey DJ

Loader cut and fill stoping was first used at New Broken Hill Consolidated Limited mine in 1966. The equipment used included single boom pneumatic jumbos for drilling up- holes, diesel loaders for ore removal and diesel utility vehicles for rockbolting and servicing. Since 1966, there have been many modifi- cations and changes both in the equipment and stoping method. Twin boom pneumatic or hy- draulic drilling jumbos have replaced single boom pneumatic jumbos, electric loaders have replaced diesel loaders, diesel forklifts have replaced utility vehicles and "'flatbacking" has superseded uphole stoping. Concurrent with this has been the introduction of cable dowels in stope backs which has enabled loader cut and fill stoping to be used more extensiv- ely than in the past. There are now six loader cut and fill stopes at both mines and this paper traces the evolution of this method outlining the reasons for changes in technique and equipment.

Jan 1, 1982

By Moy A. D

The Esperanza deposit is located 120 kin N of Mount Isa, Queensland at approximately lat 19¦20'S, long 139¦22'E on the Camooweal (SE 54-13) 1:250 000 scale map sheet. It is one of several structurally controlled copper ¦ cobalt deposits developed along the Mount Gordon Fault zone and related faults, within the Western Fold Belt of the Mount Isa Inlier (Figure 1). Together with the nearby Mammoth orebodies it forms the basis of the Gunpowder operation of Aberfoyle Limited. Until recently ore was mined from the Mammoth orebodies by open stoping with decline haulage to surface leach pads. Leaching of in situ broken ore (in place) and surface heaps, followed by solvent extraction and electro-winning (SX-EW), produced copper metal on-site. In March 1997, mining was suspended at Mammoth and the focus of the Gunpowder operation switched to development of the Esperanza orebody, which is expected to begin open cut production in mid 1998. SX-EW methods will produce 44 000 tpa of copper from an expanded plant. The pre-mining mineral resource at Esperanza (measured, indicated and inferred) is estimated at 4.6 Mt averaging 7.7 per cent copper.

Jan 1, 1997

In the search for significant new economic base-metal resources within Australia during the early 1970s BHP's Exploration Department had observed that the majority of lead and zinc con- centrate production in Europe and the USA came from carbonate- hosted Mississippi-Valley-type (MVT) zinc-lead deposits, but Aus- tralia had no history of production from this class of deposit despite several very favourable geological environments, par- ticularly in the large Palaeozoic sedimentary basins. An exploration-research team was established in 1975 and the Lennard Shelf region, near Fitzroy Crossing, was selected as a most promising geological environment. Previous exploration for this class of deposit by other companies in Australia had largely used conventional exploration philosophies (geological mapping, geophysics and geochemistry to identify specific drill targets) but BHP sought specialist advice from a North American expert and adopted a grid-drilling philosophy, which involved wide spaced relatively deep diamond drill holes on a regular grid pattern, and statistical evaluation of the results. This technique resulted in the discovery of the Blendevale Deposit in 1978 in an area which had previously been explored by other companies using conventional methodologies. The deposit was delineated and a pre-feasibility study carried out in 1985 indicated that the resource of 20 Mt @ 8.3% Zn, 2.5% Pb was a marginal proposition.

Jan 1, 1988

By P Elliott, D Pershke

In a minerals processing context, sustainability is about using natural resources more efficiently to achieve maximum economic benefits with minimal environmental impacts. It embodies five overarching themes, which the paper will illustrate with practical examples from Australian minerals processing plants. These are:resource utilisation and materials efficiency,process waste reduction and enhancement of co-product values,reduction of water use and impacts,reduction of energy requirements and greenhouse gas emissions, andenhanced control of minor elements and toxic materials. Sustainability could be embedded profitably in minerals plant design in three dimensions: 1.technology,2.design, and3.operations. This presentation discusses a set of principles that could be applied to minerals processing technologies and provides an outline of sustainability assessment and opportunities evaluation tools. The application of the tools is illustrated through a case study by analysing a suite of nickel processing technology routes. The analysis reveals that current generation of nickel processing technologies do possess real potential to emerge as sustainability champions in integrated processing of nickel ores and concentrates, if they are designed, engineered, and operated for sustainability and adapted effectively to site specific constraints and opportunities. The paper will address data gaps and uncertainties regarding the impact of scaling up of pilot-plant performance, and provides strategies to overcome them.

Jan 1, 2006

By Littlewood E

We offer these notes as a practical contribution. All the arguments we advance have been tested by practical experience.In its preparation we realised that our subject was one of such importance and covered so wide a field that, dealt with by one of us alone, it might easily have been too much for him, so we have endeavoured, by mutual criticism and advice and a pooling of ideas, to bring forward a few points that may be of advantage to members. If any of the paper is of benefit to mining on the "Golden Mile," or elsewhere, we shall feel amply repaid for our efforts.It is obvious to all that the longer the machine is working productively per shift the greater the return, to all concerned; the machine-man himself and the company. Furthermore, if a man commences a shift with a definite objective in view; for instance, to bore and fire a specific cut, which he recognizes will give him a good financial return, then that man will exercise all his capabilities to attain that objective.In this paper we hope to demonstrate the value to the machine-man of the knowledge of the capabilities of each hole he bores, so that he will be enabled to utilize his drilling time to the greatest advantage. Also, we hope to show that such drilling time can be advantageously extended.After the war, with the influx of new men to the industry, some education on the finer points of machine work may be desirable, and any instruction in this branch must stress the realization of the value of each hole.We realise that most of those present have a sound workable knowledge of machine-mining, and we are not trying to teach anyone the fundamentals of machine work, but we would like to bring to their attentIon some of the finer points which we believe are very important.The machine-man has control of gear of a capital value of over £150, and the use or misuse of that material has a direct bearing on working costs. Therefore it is imperative that the capital outlay is gainfully employed.A "bogger" in charge of a 5/- shovel engaged unproductively is bad enough. How much worse for £150 worth of gear to be not fully productive.Figs. 1 and 2 demonstrate angles of break, and the full realization of the importance of this angle is essential to our paper. Although these Sketches are two-dimensional, we hope they will be sufficient to demonstrate our meaning. We will pass over them as briefly as possible.Fig. 1 shows three holes asked to perform an identical task.(a) 7-ft. hole bored 2 ft. into solid ground-will not come out.(b) 4-ft. hole bored 1 ft. from solid ground-will come out easily.(c) 5-ft. hole bored to solid ground-the best that can be expected under general conditions encountered.The angle of break is a right-angle, normal to direction of hole.

Jan 1, 1944

By Bowling K. McG, Hamilton J. D G

The influence of three important para- meters which affect the induration of iron-ore pellets, viz temperature, time, and lime content, have been assessed in terms of internal pellet structure and commonly-used pellet quality criteria. The pellets studied were produced from a typical hematite ore from the Pilbara area of Western Australia, using a 25 cm dia. pot-grate test rig. Isothermal laboratory induration tests were conducted in accordance with a statistically-planned programme. The internal structures were studied by optical microscopic examination of polished sections of the test pellets. The effects of SFCA (silico- ferrite of calcium and aluminium) and slag formation, matrix consolidation and grain modi- fications were studied, and have been related to pellet properties and to the time/temperature histories produced by the firing conditions chosen. The implications of the data for commercial pellet plant operations are discussed.

Jan 1, 1974

By Batterham RJ

A 'research model' can be used to investigate cause and effect relations and generally improve the understanding of extractive metallurgical processes. As such, it is a useful research technique which complements the traditional methods of laboratory and plant measurement. The procedure of model development is iterative and involves observation of the process, hypothesis of phenomena, prediction using mathematical descriptions of the phenomena and comparison of predictions with real-world measurements. Lack of agreement of predictions with real-world measurements usually indicates an inadequacy in the hypotheses and necessitates revision. Experimentation has an integral role in the process of model development but its emphasis is different from that when experimentation alone is used to study processes. Since a process as a whole is investigated by using a model, experimentation is restricted to the study of specific phenomena to aid the description of these in the model, to the characterisation of the raw materials (for initial values of the model parameters) and to the measurement of physical and chemical constants required in the model equations. Similarly, plant measurements are made for the purpose of comparison with the model predictions not to establish cause and effect relations. This makes plant experimentation much simpler and cheaper'since most measurements-can be taken during normal operation.

Jan 1, 1984

By Yamada K, Abe H

Magnetic scanning type mass spectrometers have been given improved sensitivity with a large dynamic range and considerable resolution by the addition of a computer-controlled electric equipment. A mass spectrometer equipped with this newly developed electric system was applied to studies of the activities of liquid iron-silicon alloys and of liquid iron-phosphorus alloys at 1600¦C. The range of silicon concentration was 5.8at%-51.1 Si= at%, and values of ySi -3.1+0.15 and es 11.5 +1.5 were obtained. The concentration range of phosphorus was 1.3at%-5.7at% and a value of eP=7.3+0.1 was obtained.

Jan 1, 1980

By Pattinaja MA

Mathematical modelling was carried out to determine the probable convergence and vertical stress patterns around a retreating longwall panel in an underground coal mine in New South Wales. An 'Electrical Resistance Analogue' and a program called 'THREED' based on the displacement discontinuity method were used for the modelling. Parts of the obtained results are presented here and compared with some measurements of convergence at the site. The modelled and measured data agree better qualitatively, than quantitatively.

Jan 1, 1986

By Pietrobon M. C, Ralston J, Smart St C R

In an on-going study of the chemistry of base metal sulphide flotation, the effect of the inclusion of cyanide in the reagents suite has been studied, with special reference to ore from Pasminco Mining's Elura mine. Cyanide has been variously described as an iron sulphide depressant, a preventor of sphalerite activation and as an activator of galena. In the case described here, the cyanide appeared to act as an enhancer of the galena flotation performance, raising the lead recoveries by 25 per cent but leaving the sphalerite and pyrite responses unaffected. The lead rougher flotation performance with and without cyanide was investigated over a wide range of redox potentials (0 mV to 400 mV SHE). In all cases, the inclusion of the cyanide brought about an increase in the galena recovery and was responsible for a faster rate of galena flotation during the initial stages of the beneficiation. A surface characterisation study (XPS) of the lead flotation stage, with and without cyanide, indicated that the reagent interacted specifically with the galena and pyrite minerals. It was possible to correlate the surface absorption of the cyanide on the lead and iron sulphides with improvements to the flotation performance using the combination of surface spectroscopy and laboratory flotation Testwork.

Jan 1, 1991

By North R. A

The Queensland Mining Act 1968-1972 has now been in force for almost two years. The Act was completely re-written and has made for easier working, e.g., there is no distinction now between Gold Mining Leases and other Mining Leases. For the first time in the history of Queensland, provision has been made for caveats, so that options etc. can be protected. The chief problem which has arisen so far has been the question of the Government issuing mining leases to the holder of an Authority to Prospect over areas which are included iri its Authority. Litigation has taken place and an Appeal, it is understood, will shortly be heard by the Privy Council. The provisions dealing with labour conditions have been brought up-to-date and generally speaking, they are quite clear as to the responsibility of the Lessee. The Mining on Private Land Act has been repealed and the provisions relating to mining on private land are now a part of the Mining Act itself. Previously, the holder of a- mining freehold did not have to pay royalty on

Jan 1, 1974

By Nightingale R, Johnson B, Bensley C, Vince A, Keast-Jones R

In order to counter the massive increase in the level of near gravity material that would follow the reduction in dense-medium cyclone separation density at B.H.P. Slab and Plate Product Division's B and C coal preparation plants, "wing tank" systems to control medium density to within ¦0.005RD units have been installed. However, despite very precise density control, cyclone metallurgical performance has been less than satisfactory. The approaches taken to identify the causes of this poor performance and to justify alterations in operational and maintenance practices are presented.

Jan 1, 1987

By Liu Y, Campbell K. R

The paper shows how breakage parameters may he extracted from laboratory batch grinding results and how they may used with reference full-scale hall mill circuit data to estimate the likely size distributions of values and gangue in a full-sca

Jan 1, 1997

The Highlands Region of Papua New Guinea has 3 major national highways. The locations of these national highways are shown in Figure 1. The Highlands Highway begins at Lae City on the coast and passes through the Highlands towns of Goroka, Kundiawa and Mt Hagen. It terminates at Togoba approximately 10km out of Mt Hagen town. The Enga Highway begins at Togoba and passes through the towns of Wapenamanda, Wabag and Laiagam. It terminates at the giant Porgera Gold Mine. The Southern Highlands Highway also begins at Togoba and passes through the major towns of Mendi, and Tari. It terminates at Koroba station, near the Hides Gas Field. Two separate Feeder roads intersecting the main highway service both the Kutubu Oil Project and the Hides Gas Field. These national Highways play a very important role in the development of Papua New Guinea. Goods and services are delivered to the bulk of the population of the Highlands Region using these highways. Heavy machinery and equipment for the mining and petroleum projects of Porgera, Hides and Kutubu are transported using these roads.

Jan 1, 1997

The new generation Hlsmelt« Direct Iron Ore Smelting Process is a CRA Limited technology initiative. The process development is now focussed on commercialisation. The goal is to have the first commercial vessel operating around the year 2000. The HIsmelt« Process, based on the abundantly available iron ore fines and the more readily available non-coking coals, has the potential to fundamentally change iron ore processing through the application of high intensity techniques to replace the current sinter/coke ovens/blast furnace .technologies. The process will have great potential in the rapidly growing economies of Asia where steelmaking aspirations are based around local market focussed plants. This potential can be. realised as a supplier of premium grade iron units to electric arc furnace (EAF) steelmaking plants or as the front end to an ore based steel mill.

Jan 1, 1996

The operation of quarries for the production of crushed stone and aggregates, depends heavily on rock blasting efficiency, which usually represents a major share of total production costs. After investigating the causes of this situation, a series of technical aspects have been detected, and they are described for the purpose of contributing to the minimization of costs, which also reduces the effects of blasting on the environment. Utilization of empirical design methods, of inadequate explosive types, and of erroneous drilling pauems with respect to rock properties, are the main factors to be corrected, as a consequence of poor engineering criteria, with scarce use of computational methods and field instrumentation. Several concepts of blasting optimization are pointed out, and their application to industrial operations in a Portuguese limestone quarry indicated clear trends for the reduction of production costs, as well as some of the deleterious consequences of blasting on the environment.

Jan 1, 1990

By Zhen Y. Y, Cook A, Jell J. S, Fleming P. J G

Remapping of the Burdekin Basin has resulted in subdivision of the three interfingering basin-wide megafacies previously recognised in the Early to Middle Devonian Fanning River Group. Eleven carbonate and siliciclastic facies are now identified within the three megafacies, representing coastal plain, shoreline, nearshore, and shallow marine shelf depositional environments. The facies reflect two phases of a major transgression. An initial phase, in the Early Devonian, was confined to the far north of the basin, whereas a second, main phase, resulted in the encroachment of the sea from the east or southeast in the Middle Devonian.The proposed depositional model begins with the drowning of a coastal plain and the transgression of shoreline and nearshore facies between granitic and metamorphic headlands and/or islands. This was followed by the deposition of a patch reef and fringing reef complex including stromatoporoid and coral bioherms, biostromes, and oncolitic, crinoidal, and brachiopod-dominated banks/shoals, together with foreslopes and submarine channels, carbonate rubble deposits and terrigenous sediments. Sedimentation during the peak of the transgression was dominated by sheltered carbonate shelf facies, the maximum, flooding surface being recognisable across most of the Burdekin Basin. Progradation of muddy and sandy nearshore bay and shoreline facies soon followed, terminating carbonate deposition.

Jan 1, 1990

By Moore A. J, Evans R

Blast vibration control and assessment techniques have been developed which supplement traditional charge mass scaling methods. The improved techniques, which can be used to predict air and ground vibration levels at the planning stage, and to assist in the control of blasting operations, have reduced the level of operating risk concerning blast vibration. In addition to such factors as charge mass, distance and blast vibration levels, these additional techniques take account of orientation of the blasting face, topographic shielding, wavefront reinforcement, and meteorological conditions. They have assisted in compliance with specified blast vibration levels for environmental licence and mining lease conditions, the reduction of blast vibration nuisance to residents in the area surrounding a mine, and control of building and rock structure response in adjacent areas on the mine lease area.

Jan 1, 1994

Up to 80 per cent of the copper in a bornite ore can be quickly leached with percolating acidified ferric sulphate solutions. The upper limit for rapid copper extraction is set by the conversion of bornite to slowly dissolving chalcopyrite. The dissolution occurs in two stages: a rapid linear initial stage, followed by a slow, non-linear stage. The initial step is largely controlled by the rate of oxidant supply (Fe2(S04)3); temperature is not an important variable during the initial reaction. The second leaching stage is controlled by chemical and physical factors and is temperature dependent. The initial copper leaching rates are insensitive to both the concentration of the ferrous sulphate reaction product, and the sulphuric acid concentration.

Jan 1, 1973

By Haslam C. O, Los V. L, Abramson G. J

The technology applied by lonex Pty Ltd provides an important breakthrough in geochemical exploration, enabling the discovery of concealed mineral deposits to great depths below surface. Most mineral discoveries have been made in areas of outcrop or relatively shallow cover; deposits at greater depth have been beyond the range of conventional geophysical and geochemical methods. Quite apart from the need to explore to greater depths in regions of major current or past production, most continents have vast areas where prospective host rocks are concealed by more recent material. There are numerous case studies where Ionex methods have located deeply-buried metal deposits, up to 500 m below surface, beneath thick younger sedimentary, volcanic, or transported cover. Research leading to the development of this technology was initiated by Dr I S Goldberg at the Rudgeofizika Institute in St Petersburg (CIS), and the methods have been employed there - and in other countries - for many years. Ionex technology became available in Australia in 1993. It comprises: ò geochemical and geoelectrochemical sampling and ultra-high-sensitivity analysis for mobile and weakly-bonded elements (I S Goldberg); ò the delineation and interpretation of regional zones of enrichment and depletion of the prime elements within geoelectrochemical systems (GES) (I S Goldberg); ò the investigation and interpretation of the three-dimensional geochemical zoning within geochemical anomalies (G J Abramson); and ò multi-variate computer modelling of the geochemical fields and systems (V L Los). lonex technology has been adapted to the environmental conditions in Australia with the participation of C 0 Haslam.

Jan 1, 1997