Search Documents

By T Gibbons, M Korte, C Brent, K Runge

The Barrick Osborne concentrator has gone through a number of upgrades since commissioning and steadily increased production from the original 119 t/h design capacity to 265 t/h milling throughput in 2008. This was achieved incrementally over several years, by maximising operating efficiencies, in order to minimise capital expenditure, and take advantages of economies of scale; but more importantly it was reached with no measurable loss of recovery. Osborne currently processes a blend of under- ground with open pit material from the nearby Trekelano deposit. Following primary/secondary crushing, the material is processed through a rod/ball mill grinding circuit ahead of rougher/scavenger flotation that produces a copper concentrate.Osborne was seeking a further increase in plant throughput of the order of 15 per cent, but at more sustainable levels of secondary crusher plant utilisation. In early 2008, Osborne contracted Metso Minerals Process Technology Asia-Pacific and South America (MMPT) to review the entire process from run-of-mine feed to final copper concentrate. This review would be done concurrently, with surveys of both the crushing/ grinding and flotation circuits being performed at the same time. The outcome would be a steady-state model of the complete flow sheet allowing the crushing/grinding model to interact with the flotation circuit model such that overall process optimisation was possible. Two key outcomes for the operation are exploration of the operating limits of the currently installed plant, and projection of the logical next stage of potential capital plant expansions. This paper covers Part B or the flotation component of the project. A separate paper discussing Part A or crushing and grinding is also being presented at this conference. Surveys of the Osborne flotation circuit were performed along with a comprehensive review of the cell characteristics including measurements of the gas and froth phases of individual flotation cells. These data resulted in a size-by-size floatability component model of the complete circuit. This circuit model was then used to perform steady-state simulat- ions to evaluate options to improve both overall circuit and individual cell performance. The grinding circuit model discussed in a separate paper or Part A of this project was then used interactively with the flotation circuit model to recommend the best operating regime to maximise overall efficiency. For example, the balance between increased crushing and grinding costs versus higher copper recovery and final concentrate grade. Due to changes in market conditions in the fourth quarter of 2008, the focus was shifted to prioritising operational changes rather than capital expansion modifications, in order to improve circuit performance.

Jan 1, 2009

By M G. Aylmore

Thiosulphate is an attractive alternative reagent to cyanide for processing gold ores. It is relatively cheap and non-toxic, forms relatively strong gold and silver complexes, and readily leaches gold ores in ammoniacal solutions, catalysed by Cu(II). It is particularly suited to carbonaceous ores where the recovery of gold by cyanide is poor. However research over the past 20 years has identified a number of issues and impediments that must be understood or overcome before an overall process can be demonstrated as practical and economic for typical oxidised gold ores. This paper reviews our current understanding of thiosulphate chemistry and mechanism of gold dissolution, and discusses the stability of thiosulphate and polythionates. It then reviews the results of leaching various gold ores that have been reported in the literature, discusses gold recovery options, and considers environmental and toxicity issues. Some of the issues that require further research include decreasing the oxidation of thiosulphate by Cu(II) or other oxidants, increasing the extraction of gold compared to cyanide, and understanding the variation in gold recovery between ores. More work is also required to minimise the effect of polythionates on gold recovery using resins or alternative absorbents, to improve the elution of copper and gold from resins, and to recycle or minimise the concentration of reagents.

Jan 1, 2002

The products of Lower Miocene calc- alkaline activity on the east coast of Northland, New Zealand are described and contrasted with coeval rocks of the northern North Island. These rocks, the Eastern Volcanic Belt (EVB), occur in four main centres aligned north-west to south east as either plutonic/hyabyssal bodies or as agglomeratic piles and dyke intrusions. Significantly the plutonic members always occur to the north-west of the volcanic members, probably indicative of differential uplift along faults (upthrown to the north) aligned perpendicular to the EVB. A full basalt-rhyolite (diorite-granodiorite/ adamellite) spectrum is represented, with a temporal progression towards the silica-rich endmembers indicated by cross-cutting field relationships. Modal mineralogy parallels this trend, consisting of two-pyroxene, hornblende, biotite, quartz/alkali feldspar modal assemblages, and with rare occurrences of olivine and garnet-bearing volcanic phases. Chemically the EVB is medium-K, calc-alkaline (with respect to AFM and total-Fe/MgO vs. Si02 indices) and quartz and hypersthene normative. The thirty two available K-Prisotope dates indicate that activity was largely confined to the Lower Miocene (24Ma-16Ma), with an apparent younging towards the south east. Initial B7Sr/e Sr ratios (0.70335- 0.70679) are indicative of a continental- arc-type setting, however it is unlikely that a straightforward tectonic reconstruction for this part, of the Pacific Margin is possible. Evidence from xenoliths, both petrologic and isotope, within EVB magmas and from regional geologic studies suggests that hypotheses pertaining to a volcanic arc sited over a subduction zone may hold little relevance in this case. The review concludes that the EVB developed from the partial melting of a geochemically evolved lower crust as indicated by xenolith evidence. This occurred in response to thickening initiated by a short-lived obductive event in the uppermost Oligocene, and controlled spatially by pre-existing basement structure. Intra-suite chemical and mineralogic variation reflects not only crustal variability, but localized differences in physico-chemical conditions best illustrated by the rare occurrences of olivine and garnet.

Jan 1, 1987

This paper presents a review of computer techniques for the automatic contouring of geological and geophysical data with output as interactive display on graph plotters or graphics terminals and passive display on automatic drafting tables. The advantages of the method of fitting a triangulated surface to randomly distributed data using an advancing front algorithm are described, as well as the technique for determining interpolated values for the production of contour line segments and a contour smoothing algorithm. This contouring method is employed by the Geological Survey of Queensland and is implemented as an interactive system. An alternative method ideally suited to randomly distributed data involves the use of piecewise parametric cubic splines. This method which is ideal for sharp variations in magnitude and areal extent typical of geophysical anomalies is discussed. The mathematics of surface interpolation using non-parametric splines and an explicit piecewise surface fitting technique are discussed. Curve tracing techniques which are suitable for automatic contouring are also presented and the inherent advantages of interactive contouring using on-line plotters and graphics terminals for previewing of displays are described.

Jan 1, 1977

By Breen AM, Phelan JM, Doherty RJ

Early in 1990, Pancontinental Resources (Base Metals) Pty Ltd commenced flotation treatment of ore from the complex copper-lead-zinc sulphide orebody at Thalanga, 65 km west of Charters Towers in North Queensland. The orebody consists mainly of primary sulphide ore but also contains a substantial proportion of supergene ores which are being processed during the first year of operations. The supergene ores are of three main types, designated as A, B, and C. Supergene A ores are essentially copper ores, containing little lead and zinc, while B and C ores are copper-lead-zinc ores with different degrees of alteration of the original chalcopyrite and different ratios of copper to zinc content. Copper is present in the supergene ores mainly as chalcocite, digenite and covellite. Lead and zinc occur mainly as galena and sphalerite respectively. This paper describes the development of flotation plant practice, aided by laboratory testing, to process the supergene ores. The major challenge in treating these ores is that a varying proportion of the sphalerite is naturally activated and is not easily depressed in flotation by the conventional zinc depressants.

Jan 1, 1991

By P Mavros, K A. Matis, N K. Lazaridis

A large number of techniques are in use today to limit membrane fouling, among them certainly is air bubbling (which constitutes the transport medium in flotation) as applied in wastewater treatment; meanwhile, dispersed-air flotation is suitable as a pretreatment stage for microfiltration. The invented and investigated hybrid cell combines the advantages of both flotation and membrane separation, while overcoming their limitations, producing clean water from industrial wastewater. Metals recovery from dilute aqueous solutions is a promising application of this innovative hybrid process of flotation and microfiltration, further to solid/liquid separation. In this study, ceramic flat-sheet membrane modules were inserted inside a typical flotation cell in the laboratory tests, using multichannel geometry, combining flotation with microfiltration by submerged membranes; the latter requiring periodic backflushing. The specific objective was to apply this process for the efficient separation of effluents containing metal cations (here, zinc). The main examined parameters were: the initial metal concentration, flotation surfactant applied and air flowrate. The successful contribution of precipitate flotation was highlighted, while the observed metal removals were of the order of ~100 per cent.

Jan 1, 2005

By S R. Grano

The selection of the proper frother, specifically for a given ore, is essential in flotation. Traditionally, strong and stable froths are required in the scavengers, where metal recovery needs to be maximised, while selectivity must be achieved in the roughers and cleaners, where grade of concentrates is the main issue. The physical properties of a froth are determined both by frother type, by process water composition and by the amount and nature of the suspended particles. The evaluation of different frothers, in terms of metallurgical performance, is complicated at plant scale, since it may lead to periods of malfunctioning of the process and unacceptable decreases in recovery. On the other hand, evaluation based on frother chemistry only, is often unsatisfactory, because the frothing response is strongly ore dependent. A procedure, and proper tools, was developed at the Wark in order to perform the screening of candidate frothers at batch scale on real pulp samples. The main parameters related to froth stability (half-life time, froth height) are measured after introducing the pulp samples into a foaming column, where different conditions in terms of frother addition, agitation and aeration can be maintained. The approach has been applied to the selection of frothers for the flotation of an Australian sulfide ore. Procedure and results are discussed.

Jan 1, 2006

By Munro DL

The Mary Kathleen uranium deposit is in north-west Queensland, approximately halfway between the townships of Mount Isa and Cloncurry, at long. 1400 009 E and lat. 200 44' S. The deposit Iwas discovered by prospectors of the Walton McConachy Syndicate early in July, 1954, and climaxed a very intensive ground search by hundreds of part-time prospectors. during the uranium boom from March to July 1954ò Numerous small deposits, mostly in the vicinity of Mount Isa, were discovered in various rock environments, but Mary Kathleen is the only large deposit and, apart from a few tons of hand sorted material from the Milo lease, is the only deposit that has been worked. Exploration of the surrounding area, and proving of the economic worth of the deposit, were conducted from the time of discovery until February 1956 by a geological team camped near the deposit. Proving was carried out by drilling a pattern of vertical and inclined diamond drillholes at fifty-foot centres over the outcrop. An adit was driven eastwards through the deposit. Metallurgical research and design work in the South Australian Department of Mines Adelaide Laboratories were based on core samples and bulk samples from the deposit. The signing of a contract in March 1956 with the British Atomic Energy Authority to supply 4500 short tons of uranium oxide allowed mining to commence, and enabled the planned construction of water supply, township and treatment plant to proceed. The open out mine and plant are now serviced by a modern township, four miles away, which is connected to Cloncurry and Mount Isa by road. Although little field work has been done since the exploration phase, this paper differs in interpretation from a previous paper (Matheson and Searl, 1956) in that it is based on a revised structural inter- pretation (Compana, 1958), detailed mapping of progressive exposures in the open out, and a re-examination of diamond drill cores.\

Jan 1, 1968

Evidence abounds for sea-level change having occurred throughout geological and recent time. Driven by climatic changes, by cycles of glaciation and deglaciations, and by tectonics the position of sea-level relative to the crust has been going up and down since oceans first formed. Rates of these differential movements have been as high as 10 mm/year during the last major deglaciation as sea-level rose by about 150 m in about 15000 years. Tectonic processes can also produce change in sea-level relative to the crust of several mm/year as in, for example, the uplift of the Huon Peninsula in Papua New Guinea. To understand what is happening to sea-level today and what may be happening in the future it is necessary to understand the geological and climatic processes that have caused sea-level to change in the past and the best laboratory for the study of these processes is the geological and geomorphological record. Evidence for observations of sea-level change throughout Late Pleistocene and Holocene time is plentiful in the Australian region. Temporal variability is characterized by a low-stand, at more than 100 m below the present level, at about 20 000-18 000 years ago followed by a rapid rise and transgression of the continental margin up to about 6000 years ago. After this time sea-levels remained within a few metres of their present value but the patterns of change are not everywhere the same. The depth of the low stand at about 18 000 years ago does not appear to have been the same everywhere. Nor does the time at which sea-level first reached its present value appear to have been everywhere the same. The fluctuations about present sea-level during the past 6000 years appear to have been different in different localities. As yet there has not been a wholly satisfactory quantitative explanation for this spatial variability. How much, if any, is indicative of vertical tectonics? How much is the result of the Earth's response to the changing surface loads as mass is exchanged between ice sheets and the oceans? Can any of it be attributed to past changes in global climate? Or are the observations just wrong?

Jan 1, 1990

Estimation of the semi-variogram is basic to the geostatistical processing of data. The most widely used arithmetic average estimator is here employed with various sampling patterns to calculate experimental semi-variograms in a deposit which is simulated to have a defined semi-variogram. Percentage differences between theoretical and experimental semi-variograms are reported.

Jan 1, 1984

Martite-goethite high-grade iron ore deposits that show no trace of hydrothermal alteration may extend to more than 200 m below the permanent water table and are typically saprolite with evidence of exposure to the physical, chemical and biogenic processes of soil formation restricted to the low-grade goethitised upper levels. Typically no evidence of the prior presence of chert bands is discernable within the ore yet it has been assumed that these ore deposits derive from cherty banded iron formation (BIF) through supergene leaching of the chert bands and thus classified as supergene iron ore deposits. The fact that chert bands are absent and that these ore deposits are highly weathered does not prove supergene leaching of the chert bands. Quartz is one of the most resistant minerals to chemical weathering within the saprolite and large scale dissolution of quartz is absent from all other quartz-bearing saprolites, yet this unlikely process is accepted without question as the origin of the most abundant form of high-grade iron ore deposits. It is proposed that martite-goethite high-grade iron ore deposits formed only from BIF in which chert bands were absent prior to weathering. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Australian wheat belt agriculture is causing a decline of its natural resource base. The major problem, salinity, arises from a small reduction in water consumption by agricultural crops compared to what prevailed under the prior native vegetation. This causes groundwater accumulation which, in the low relief landscapes of the wheat belt, is leading to extensive surface saturation in low landscape positions and dramatic, destructive change in the hydrological behaviour and habitat of streams and rivers. The ability of agriculture to invest in salinity control is severely limited by its long-term decline in its terms of trade. Extensive planting of perennial vegetation has the potential to increase water use and arrest the salinisation process. If these perennials were also commercially attractive, the cost of salinity treatment could be minimised. Given the difficult commercial position of food commodities, it is logical to develop ænon-foodÆ perennial crops, in particular woody crops suitable for industrial products. This paper looks at the example of Sweden, where there has been a generation of investment in developing forest harvest residue recovery, and short cycle woody crops for bioenergy, but with only limited success. In contrast, secondary residues (processing wastes) from forestry industry are readily saleable for low value uses like bioenergy. This suggests that the model woody crop must have a higher value fraction to facilitate delivery and commercial use of its lower value fractions. This model is being emulated in the development of native mallee eucalypts as short cycle woody crops in Western Australia. Some $50 million has been expended on mallee development in the past decade and this has culminated in an engineering demonstration of integrated processing. The putative high value products are activated carbon and eucalyptus oil and the residue (plus waste heat) will be converted to electricity. The potential scale on which crops of this type would be required to achieve salinity control means that many more high value and residue products will have to be developed. Metallurgical charcoal appears to be a promising product option.

Jan 1, 2006

Elimination of zinc by the reduction of iron works dusts is examined. The process consists of blending, filtration, drying, balling, preheating and reduction in the rotary kiln. Dust slurries and dry dusts are mixed and stored in slurry basins and the blended slurry is filtered. In the balling process it is important to make green pellets which will withstand Thermal shock in the preheater and rotary kiln. Preheating to about 2000C is preferred to ensure effective use of coke fines in the blast furnace dust. The coke retained in the pellets accelerates the reduction rate. However, at the initial stage of the reduction the pellets become weakened and have to be heated slowly to prevent ring formation. In order to ensure zinc vaporization, pellets should be heated to a temperature of 1100-11500C in the kiln with injection of l ignite fines from the discharge end. Pellets having a degree of metallization of more than 90% and containing less than 0. 1% zinc have been obtained using a test kiln. The final pellet product is intended for use as blast furnace feed. A new plant with a capacity of 20, 000 tonne of dust per month is now under construct- ion and will be in operation next year.

Jan 1, 1974

By T Berryman

The Fimiston reserve is being depleted at the rate of one million ounces per year; most of which is processed by the Fimiston plant, with the remainder being stockpiled. As for most other large open cut mines around the world, Fimiston has an excellent dispatch and tracking system. Reconciliation is used to determine how the various models used in mine planning (such as a reserve, budget and schedule models) are tracking against production. It is also used to gauge the performance of grade control estimation against production; however, analysing the results of this can be complicated and, at times, misleading. The reconciliation process involves adjusting the monthly production data to equal the mill reported tonnes and grade, plus the change in stockpiles. This adjusted number is then compared to the grade control reported tonnes and grade, the scheduled model (monthly planning model) tonnes and grade and against budget (Reserve) tonnes and grade. This paper includes explanations of all assumptions made in the reconciliation process, including the end of month closing stocks balance, the application of adjustment factors to the dispatch data to create a new balanced set of production data and the monthly sign off to comply with the Sarbanes-Oxley requirements of the North American owners. The reserve is reconciled by proved and probable classification. This tool is used to assess the robustness of the classification scheme utilised and identify any reconciliation issues as they arise. Within the Fimiston deposit there are still issues that are clouded by the assumptions made concerning the scale of observation, poor data support and the mining of the narrow lode areas of the deposit. The declared ore mined (DOM) number (which is defined in the paper) can be significantly affected by these assumptions, and these need to be clearly stated and understood when looking at the reconciliation data. The DOM tonnes and grade is a good indicator of real mine performance as it adjusts mined tonnes and grade to take into account the milled tonnes and grade each month, and prevents cumulative errors from building up in mine predicted dispatch numbers or end of period stockpiles. This number allows monthly monitoring of the mine to mill performance and allows valid comparisons to be made back to budgets and reserves over a period of time. KCGM uses three month rolling averages to monitor performance against reserve and budget models. This ensures that monthly distortions in the figures due to stockpiling issues or over mining in a particular period do not lead to false conclusions. Reconciliation performance over a longer period (12 - 18 months) is used to adjust reserve models should significant variance be observed. By closely monitoring the reconciliation performance at the Fimiston operation, fine tuning of all aspects of the grade estimation process from reserve through to grade control can be made. This allows the most accurate data to be used when planning from reserve data for the Life of Mine Plan through to grade control data for short-term mill feed.

Jan 1, 2006

By Y Wei, P Soole

This paper gives a brief description of VirtuoBlast technology ù a new, automated and highly interactive stereo vision technology which has been developed in CSIRO Exploration and Mining. VirtuoBlast technology is an integration of three advanced technologies - close-range digital terrestrial photogrammetry, oblique stereo imaging or high-speed stereo imaging, and temporal-spatial image matching technique. VirtuoBlast has been developed for the automated 3D measurement of blasting through rapid collection, processing, analysis and visualisation of 3D data related to blasting. A major field trial has been undertaken in August 1998 at the KCGM super pit. The field trial involved three applications of the technology, namely, pre-blast 3D surface mapping; post-blast 3D performance measurement; and temporal-spatial modelling of dynamic blasting process. This paper presents some results from this trial with emphasis on the application of VirtuoBlast technology to pre-blast 3D surface mapping and post-blast 3D performance measurement. Application to the temporal-spatial 3D modelling of dynamic blasting process will be presented in a separate paper. Pre- and post-blast surface models derived using both VirtuoBlast technology and conventional field survey method are presented. The differences in results using the two mapping methods clearly show that the digital photogrammetric technique has many advantages over conventional survey methods. Results of pre- and post-blast from the field trial have demonstrated the potential of VirtuoBlast technology to efficiently perform pre-blast 3D surface mapping and post-blast 3D performance measurement of production blasts. Demonstrated applications of VirtuoBlast technology to automated 3D measurement of blasting are showing an exciting future in advancing blasting science and modern blast design. The basic technologies are in place, however, continued improvements to the functionality, robustness and outputs are needed. The challenge is to build on the current state-of-the-art, by developing techniques and hardware which can be easily transferred to and implemented by the mining community. Current and future research and development will see improvements in imaging systems, automatic image processing and 3D data analysis.

Jan 1, 1999

By B, J Bianchini, N Voermann, C Crowe

Operational and economic imperatives in the metallurgical industry have led to numerous advancements in furnace design. Modern furnaces provide high production rates, high percentage online time, long campaign life between rebuilds and safe operating conditions. Current trends for maximising plant efficiency include increasing the throughput of existing process vessels (often by a factor of two or more) and the use of newer, highly intense processes. In both instances, the process intensity results in the generation of higher heat fluxes to the crucible walls. High-intensity furnace operation with the objectives mentioned above has become possible with the following furnace design features: Strong sidewall cooling systems, using copper coolers, to accommodate the high heat fluxes encountered while protecting the crucible refractories; Robust, spring-loaded furnace horizontal and vertical binding systems which maintain tight brick joints through-out all stages of operation; and Well-designed, intensely cooled tapholes for metal, matte and slag. The integration of these features along with properly selected refractories, appropriate instrumentation systems and efficient water-cooling systems is also highly critical. These design features have been successfully implemented in electric smelting furnaces, flash smelting and converting furnaces (Outokumpu and INCO types) and lance injection furnaces (Mitsubishi, Ausmelt and Isasmelt types). This paper will discuss design aspects and operating results for several installations.

Jan 1, 2002

By Bekturganov NS, Satayev I

The paper deals with the effect of sodium polysulphides in chrysocolla flotation. Activity of elementary sulphur adsorption on the mineral surface is discussed. The mechanism of polysulphide action in the process of sulphidisation and formation of sulphur on the mineral surface is proposed. Sodium pentasulphide is shown to be the most effective modifier of chrysocolla flotation.

Jan 1, 1993

Human resources (HR) practitioners use a general suite of tools that they adopt to suit their company needs and profile. This paper will cover the main areas of a selection and recruitment process from applying for a job, resumT writing, participating in an interview finalising the job offer. A holistic recruitment process has many facets to it. These processes can be quite sophisticated and technical but at the end of the day they are designed to identify talent. A recruitment process will generally include: ability testing (usually online);telephone interview;face to face interview;behaviourally based interviews;psychometric assessments;presentations;simulations (independent or team based); and assessment centres, etc. Understanding the basis of these tools will go a long way to prepare you for the job market, enhance your performance in a recruitment process and stand you out from the pack.

Jan 1, 2008

Geological modelling is a crucial preparatory stage to most facets of the mine planning of an orebody. The process of modelling involves skilled geological interpretation. Recent innovations in computer software and graphics hardware provide many tools which can be used to dramatically improve on manual methods of interpreting orebody data. Geological interpretation can be carried out quickly to produce accurate block models for many orebody attributes, such as grades, and these models can be easily updated locally as exploration and mine development data become available. The speed of the modelling process coupled with the mass storage capabilities of the computer now allows geologists to optimise the geological model or carry more than one model through to the mine planning phase.

Jan 1, 1987

It is usually the case that the short-term plannerÆs role is occupied by the younger site mining engineer. ThatÆs because mine scheduling is generally seen as a mundane and thankless task. But, short-term planners play an extremely important role in maximising the value of the mining resource, generally the companyÆs biggest asset. A look at any mining operation today will expose the competing drivers behind the operational and strategic plans. Operations are too often faced with pushing short-term constraints. It is the responsibility of the short-term engineer to answer the question of æWhere to next?Æ. In answering this question the young mining engineer is in an environment overflowing with urgency and constraints. Hasty decisions made at this time may have significant adverse consequences to the long-term value of the resource. Long-term strategy must address a broad and expanding number of issues that are generally overlooked by the short-term planner. It takes a holistic, rather than the prescriptive approach of short-term planning to determine the best strategic direction for the operation. To better understand the consequences of decisions made at the operational level short-term planners need better vision of the whole business. The key to improving the mining business is a planning process that integrates the short-term planners role with the overall mining strategy. Future developments in the mine planning process will focus on bridging this ædisconnectÆ between the operational objectives and the long-term goals. Improvements will come from the tools which planning engineerÆs use, and the planning methodology surrounding them. There will be significant hardware improvements to improve the speed with which a short-term planner can evaluate plausible options. Software that maximises the use of the improved hardware will be developed. Complimenting these technological improvements, conceptual methodologies of mine planning will improve to allow strategic planning to be brought within the focus of the short-term planning engineer. In todayÆs mining industry the young mining engineer is embarking on a career where business processes are paramount. This paper discusses the ædisconnectÆ that occurs today between the operational planning and long-term strategy and how this is driving developments in mine planning today.

Jan 1, 2003