Search Documents

By D A. Deglon

Solids suspension is important in the design and operation of mechanical flotation cells, and is a necessary precondition to particle collection. Most of the fundamental hydrodynamic research that incorporates some aspect of solids suspension was done by Arbiter, Harris, and co-workers, or Schubert and co-workers. However, a need for research into solids suspension in mechanical flotation cells exists, since very little has been done since the late 1980s; a time that also coincides with the advent of round mechanical flotation cells and the subsequent dramatic increases in maximum flotation cell sizes. In this work, concentration profiles and critical impeller speeds, Njs, were measured in a 0.124 m3, round cell fitted with a 0.150 m, Bateman impeller mechanism. Two solids size fractions (75 - 106 and 150 - 250 ¦m) were tested, in ungassed and gassed conditions (JG = 0, 1 cm/s) and at various impeller speeds (300 - 900 rpm). The effectiveness of solids suspension was quantified in three ways in terms of extent of off-bottom solids suspension, suspension height (extent of solids distribution), and variation within the solids distribution, which together present a complete quantitative picture of solids suspension and distribution within the cell. Consistent trends were found when these effectiveness criteria were considered against relative impeller speed, in terms of percentage of critical impeller speed, N/Njs. Off-bottom solids suspension is complete at or above 100 per cent of Njs, with significant sedimentation occurring as the impeller speed drops below 60 per cent of Njs. Suspension heights consistently reached a level equivalent to 90 per cent of the tank diameter at the critical impeller speed, and dropped off significantly as N/Njs dropped below 60 per cent. The variation in the solids concentrations within the sampled profiles showed consistent trends in two-phase but not under three-phase conditions. The paper concludes that the critical impeller speed, Njs, commonly used in the design and operation of standard stirred tanks, is a very useful solids suspension benchmark for describing all aspects of solids suspension in mechanical flotation cells and should be correlated to system conditions.

Jan 1, 2005

By Shrivastava P

The iron orebodies of the Pilbara region are formed by supergene enrichment of banded iron formation and rarely do such processes produce orebodies with uniform grade distrib- utions. The orebodies being mined or developed have to be worked to grade/quality constraints imposed by contractual agreement rather than natural characteristics. Hence it is imperative to use a non-biased ore reserve calculation method. The geostatistical study of a typical iron orebody is presented. Emphasised are the geological characteristics of the orebody manifested as a variable grade distribution of iron and impurities; the determination of variogram model; subsequent uses of the model for computation of ore reserves and kriged lock estimates; computation of dispersion variance and conditional simulation of orebody.

Jan 1, 1977

By Matveeva TN, Lunin VD, Ivanov VA

The results of theoretical and technological investigations have been presented for the application of electrochemical technology in copper-nickel flotation processing schemes. The sorbed xanthate and dithiophosphate products on chalcopyrite and pyrrhotite have been studied in distinct polarisation conditions of mineral suspensions. Optimum electrochemical pulp treatment parameters have been worked out for copper, nickel, pyrrhotite and other flotation cycles. The method has been examined in pilot plant conditions over a long period of time, technological efficiency has been evaluated corresponding to the industrial flotation process at the Norilsk plant.

Jan 1, 1993

By B McFadyen, Y Potvin, K Woodward

The Australian Centre for Geomechanics (ACG) held two workshops in 2019—one in Australia and one in Canada—to discuss processes and methods currently used in the mining industry for stope design and reconciliation. In practice, this work strives to optimise stope performance and aims to maximise ore recovery (minimise underbreak), while minimising dilution (overbreak). One of the key findings from the workshops was that current stope design practices, almost exclusively, rely on some versions of the empirical Stability Graph methods developed in 1980s. Although robust and useful at the feasibility study stage, there are a number of inherent shortcomings with this approach. The Stability Graph’s limitations first lie in that it cannot assess underbreak, which is a very important measure of performance. Furthermore, the method doesn’t consider a number of factors which often have a critical influence on stope stability, for example, drilling and blasting or the presence of faults. Given the current industry standard practice, there is a great opportunity to reinvent the stope design process to optimise performance. A finding of the workshops was that every mine quantifies stope performance in terms of volume reconciliation with a focus on dilution and ore losses, and reconciling metal tonnes recovered from the mill. Many mines further investigate stope performance by looking at individual stope faces and the causes for the deviations between the planned stope shape and the measured cavity. Recent research at the ACG has shown that investigating overbreak and underbreak at a higher resolution is a powerful way to identify the root causes of overbreak and underbreak. Finer scale assessment is achieved using an octree analyses, which effectively divides the relevant stope volume into cubes on the scale of a metre and produces many tens of thousands of data points. The octree data structure and subsequent analysis underpins a data-driven stope design methodology. The ACG is currently developing a design approach based on multivariate modelling methods that can account for the many variables that influence stope performance and forecast stope overbreak and underbreak results. Back-analysing stopes based on octree reconciliation results provides a rich database for training the model. Once the model can achieve reliable forecasting of overbreak and underbreak, an interactive drill-and-blast design will allow for the assessment of different firing strategies to optimise stope performance.

Mar 15, 2021

By H Aral, L Malishev

The carbothermic chlorination of titaniferous materials such as rutile, synthetic rutile (SR), upgraded slag and ilmenite in a fluidised bed is an established commercial process. In this work, ilmenite sourced from the Murray Basin area of South Eastern Australia was chlorinated and an assessment of the chlorination characteristics of the ilmenite, in terms of pre-treatment, type of reductant and reaction time was made. Selective chlorination of Murray Basin ilmenite to remove Fe and Mn was achieved in this work. A synthetic rutile sample containing around 93 per cent TiO2, one per cent Fe2O3 and 0.5 per cent MgO was produced at a chlorination temperature of 1000¦C with around 25 per cent loss of Ti as TiCl4. Raising the reductant to ilmenite ratio in the chlorination reactions increased the amount of Ti chlorinated. However, complete chlorination of Murray Basin ilmenite to produce FeCl3 and TiCl4, was not achieved under the conditions used in this work. Pre-oxidation of Murray Basin ilmenite before chlorination had little affect on its reactivity, compared with æas receivedÆ ilmenite. In contrast weathered West Coast ilmenite chlorinated appreciably better than West Coast primary ilmenite, in terms of bed residues remaining and amounts of elements removed. The presence of large amounts of Mg and chrome spinel grains in the Murray Basin ilmenite used in this study are likely to make it difficult to chlorinate directly in a commercial chlorinator. However, this is not to say these ilmenites will be unsuitable for chlorination applications. Further work is needed in the separation of Mg and chrome spinel grains from Murray Basin ilmenites and the products resulting from these tests could then be assessed in terms of chlorination performance, so that further processing options can be explored.

Jan 1, 2000

By R L. Verburg, R Johnstone

DeBeers Canada Mining Inc (DeBeers) recently submitted an Environmental Assessment (EA) for its proposed Snap Lake Diamond Mine located in Northwest Territories, Canada. As part of the EA process, a site water quality management plan must be developed. Plan development requires an integrated approach such that the key factors influencing water quality can be identified and managed to minimise potential impact. A system model was therefore developed to simulate the site-wide water quality conditions and mass loadings to the principal environmental receptor of concern, Snap Lake, during operations and post-closure. Requirements of the simulation included integrating hydrology, geochemistry, hydrogeology and site management practices in a dynamic way. A unique feature of the site was the need to accommodate a complex flow system that included a feedback loop between lake water and mine water. A system model was constructed using the GoldSim software package that integrated on-site water quality and flow measurements, as well as results from independent groundwater flow and geochemical modelling efforts. The GoldSim model simulated concurrently the movement of 39 solutes through the subsurface mine and surface facilities. Solute sources considered included four different waste rock and tailings types, explosives use in the mine, treatment plant discharge, and recycled process water for dust suppression. Separate solubility constraints were identified for different regions of the flow system (eg underground mine; treatment facility; surface water bodies). Kinetic test data were used to derive temperature-dependent rate constants for use in calculating mass inputs from surface sources such as waste rock piles. The model generated water quality estimates over time for a variety of management scenarios at several potential discharge locations. The integrated approach used by the model was effective in identifying the significance of key factors influencing overall water quality such as explosives use, mine water inflow rates, waste rock reaction rates, site/mine management options, and effectiveness of treatment. The model provides an example of an effective tool for comprehensive, integrated system evaluation and management.

Jan 1, 2003

The Youga gold mine in Burkina Faso, West Africa, is scheduled to produce first gold in the third quarter of calendar 2007. The project is expected to produce 540 000 oz of gold over 6.5 years, from a conventional open pit carbon in leach mine. The direct capital cost of the project is US$47 M. Etruscan Resources Inc, a Canadian based gold exploration and development company, holds 90 per cent of the project company Burkina Mining Company SA (BMC). The state of Burkina Faso is free-carried for the remaining ten per cent of BMC. RMB Resources Limited, of Melbourne Australia, has arranged a US$35 M project finance facility for BMC (the Borrower) as the majority of funding for the Youga project development. The loan facility was provided by RMB Australia Holdings and Macquarie Bank Ltd (the Lenders) each as to 50 per cent in the lending syndicate. The Lenders also provided a gold hedging facility to guarantee a minimum price for the projectÆs gold production. Burkina Faso is a francophone country, part of the Economic and Monetary Union of West Africa (UEMOA). The project financing is the first such facility to be arranged for a mining project in Burkina Faso, with little or no precedent available in other UEMOA countries. Therefore, while the Youga gold project is forecast to be a robust project applying conventional mining and processing methods, a number of legal, technical, commercial and social issues required identification, evaluation and resolution before the loan could be established. This paper describes that evaluation process and the resolution of these issues. In-house experience and expertise in both the LendersÆ and BorrowerÆs teams has facilitated a greater understanding and æownershipÆ of the issues and hence provided comfort with risks which might not normally be taken in conventional project developments and project financings. As a result, blanket external reviews were not required by the Lenders. A long-standing relationship between Etruscan and RMB Resources also facilitated solutions to a number of issues. Nevertheless, a degree of flexibility by the Lenders, the Borrower and Etruscan was required to successfully close the financing.

Jan 1, 2007

By B Maybee

In underground mine planning, many potentially value-eroding decisions are made due to a lack of time and proper evaluation practices. The information required for mine planning decisions goes beyond external sources of uncertainty that are recognised by typical evaluation techniques used in the mining industry, to include technical factors (eg mine development layout) and the ability of a mineral extraction project to achieve its anticipated production levels. Due to the individual characteristics that define underground mining projects, each will exhibit a different risk profile, and thus advanced optimisation and evaluation techniques are required to capture this information.As underground mine planning tools become more sophisticated, mine planners have the capacity to investigate numerous mine sequencing options to identify the best strategy for a given project, creating higher value for shareholders. This paper describes a risk-based evaluation methodology (RbEM) that accounts for financial and technical risk in the evaluation of underground mining projects. While the use of the RbEM has been described in previous works, no benchmarking of the benefits that can be realised from a change in those decisions that are made early in the process has been undertaken. To show the benefits that can be achieved from using the RbEM, this paper updates a case study to which the RbEM was applied, and takes a retrospective look at whether additional value would have been gained by following the strategic recommendation of the RbEM versus a typical optimisation exercise that aims to maximise the net present value.CITATION:Maybee, B, 2012. Can a risk-based evaluation provide a more valuable mine design?, in Proceedings Project Evaluation 2012 , pp 53-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By J N. Moncrieff

The resource estimation process for the underground Mount Isa Copper Mine has undergone significant change. Block models are now created using a commercial software package as opposed to the in-house software that was previously used. With mineralisation occurring over a strike length of more than 4 km, Mineral Resources for all categories totalled 190 Mt at 2.7 per cent Cu at 31 December 2002. Estimation is by ordinary kriging with two separate models generated to cover the X41 and Enterprise orebodies respectively. The underlying Upper Basement Contact and the silica-dolomite alteration envelope are both used as hard boundaries to constrain the modelling. From a validated block model, grade shells are generated at the appropriate cut-off grade for a given area. The grade shells are depleted for mined voids and subdivided into 30 metre strike length blocks. Application of a SMU criteria and crown and pillar constraints results in failed blocks being culled from the resource inventory. Mineral Resource blocks are further subdivided into resource categories (Measured, Indicated, Inferred) by the Competent Person on the basis of geological confidence, taking account of geological and grade continuity, drillhole spacing and structural complexity (JORC, 1999). A geostatistical æconfidenceÆ category is incorporated into the block model as an additional tool for the categorisation process. The shapes are assessed in concert with a mining engineer to determine whether a reasonable expectation of mining potential exists and if not they are removed from the resource. The final categorised blocks constitute the Mineral Resource inventory and form the basis for conversion to Ore Reserves. The resultant Mineral Resources and Ore Reserves are reported on an æinclusive ofÆ basis.

Jan 1, 2003

This subject of paramount importance in many modern plants employed in the extraction of gold from ores by cyanidation, involves several considerations.With the old-type "slimes decantation" process, using several tanks of large dimension, installed at high capital cost, it was frequently possible to obtain good settlement over a protracted period, but the disability of indifferent response to subsequent filtration and washing of the residual pulp, after decantation of the supernatant pregnant solution, was often present.In modern cyanidation practice, the tendency is to reduce capital expenditure by continuous processing of the ore pulp in a plant of less volume, but capable of handling more tonnage through-put and yielding, coincidently, less residual dissolved gold in the final pulp residues.INHIBITORY FACTORS.These involve a study of the effect of the circuit water or solution employed in milling and treatment, the amount of "primary" slime occurring in the ore broken underground, the constitution of the "walls" underground, the inherent occurrence of colloidal slime in partially decomposed ore, and the presence of kaolinised and ferruginous clayey structures carrying payable infiltrations of gold values, to mention some of the troubles encountered in practice. Practically all the difficulties occurring are due to the presence of colloids (using the metallurgical as apart from the chemical definition of the term), either...

Jan 1, 1935

By P Ireland, S Mitra, G Evans, A Wang, M M. Hoque

This work presents an experimental study of flow dynamics in a bubble column system (crosssection: 100 mm × 100 mm) using a non-intrusive optical technique with targeted application in a novel REFLUX™ Flotation Cell. The study had two aims – measurement of the bubble size distribution (BSD) and local energy dissipation rate in the system due to bubble motions over a low range of gas flux varied from 0.02 to 0.08 cm/s without impairing the visibility of the system. A central bubble plume was generated by injecting compressed air through a sintered glass distributor in quiescent liquid. Highspeed shadowgraphy imaging was performed to determine the BSD in the presence of surfactant (Sodium Dodecyl Sulfate (SDS) concentration ~ 10 ppm). The BSD exhibited a unimodal shape at different locations of the column for all gas flux cases. A non-intrusive particle image velocimetry (PIV) technique was used to quantify the flow field generated by the bubble motions, which was used to estimate the local energy dissipation rate. The local energy dissipation rate exhibited an increasing power-law dependency on the gas flux.

Aug 24, 2022

By S Miller, A Neale

As part of a long-term acid rock drainage (ARD) mitigation study, PT Freeport Indonesia has completed the construction of a highly instrumented, full-scale, experimental, overburden stockpile to further evaluate the behaviour of the waste rock system at Grasberg mine. A total of 24 lysimeters, 30 sets of thermistor strings and 48 oxygen-sampling ports were installed at select locations during stockpile construction. ARD flow rates and chemistry have been recorded since the start of overburden rock placement in April 2000. Measurements of in situ temperatures and oxygen concentrations quantify reaction rates and the oxygen pathways that control oxidation kinetics deep within the waste rock profile. Direct field observations show the significance of advective oxygen flow with respect to the onset of oxidation kinetics. Oxygen measurements show that the rubble zone that forms at the base of a waste rock bench provides a critical pathway for oxygen entry to the waste rock profile. Furthermore, rapid oxidation as evidenced by measured temperature increases deep within the panels of waste rock is observed to occur. The observations presented in this paper provide critical insight for understanding the mechanisms and behaviour of full-scale waste rock stockpiles with respect to ARD generation. The results of this program will assist in the future selection, testing and evaluation of appropriate mitigation measures with respect to surface and face treatments to reduce long-term ARD generation. This project is a work in progress, and at least another two-years will be required to fully understand site-specific ARD generation and ARD mitigation mechanisms. This paper will discuss various design and construction considerations, provide an overview of results achieved to date, and some preliminary interpretation of what is happening within the overburden stockpiles.

Jan 1, 2003

By Waters CA, Happ JV

The debismuthising plant, commissioned in 1980, is based on the Kroll-Betterton process for preliminary bismuth removal with subsequent antimony treatment for fine debismuthising. Bullion flowrate is continuous and the plant was designed to achieve low bismuth lead product at rates of up to 20 tonne/h.Development of the first stage of the operation has enabled reliable operations at 25 tonne/h to be achieved. Thesedevelopments also introduced the opportunity to treat higher bismuth bullion at up to 35 tonne/h when operating the first stage only to produce product lead of 0.029 per cent Bi, meeting the ASTM B29-55 Corroding Lead Standard.

Jan 1, 1985

By Davies C. E

At present the source of virgin iron for steel produced in New Zealand is titanomagne- tite extracted from titaniferous beachsands. Some of these beachsand deposits contain extractable quantities of ilmenite as well as titanomagnetite and both minerals represent challenging sources of vanadium and titanium products in addition to iron. This study looks at some theoretical aspects of smelting these ores directly with coal rather than with electric power, and takes into consideration the properties of the raw materials, the thermodynamics of possible process routes and the background of the economics involved.

Jan 1, 1980

By Quemard D, Troncoso J

The Gordonstone Project with a capital cost in excess of $500 million will become the largest underground coal mine in Australia. The project development decision was taken on 31 July, 1990 and at 31 May, 1991 construction was approximately 35 per cent complete. The first train of processed product coal will be railed to Gladstone during December 1992. The general theme of this paper therefore will address the planning and development processes at Gordonstone particularly the interrelatedness of technical, production, construction and environmental disciplines to ensure success during operations.

Jan 1, 1991

By K L. Silversides, A Chlingaryan, A Melkumyan

Multiple data sources can be fused to improve boundary modelling in stratified deposits such as the banded iron formation (BIF) hosted deposits in the Pilbara Region of Western Australia. Accurate boundaries are essential to produce high quality geological models. Initial models are based on the widely spaced exploration hole data. This creates a high level of uncertainty in areas between the holes, with different interpretations of the boundary equally probable. Including directional information collected in these holes in the models can reduce the number of possibilities. Including data collected during mining, such as blastholes and bench measurements, can further guide the model. This research demonstrates a Gaussian Processes based method of fusing these disparate data sources to better inform the boundaries. Our results demonstrate that when only exploration points are used the model creates a smooth boundary with minimal variation between the holes. Each additional data source refined the model and added additional detail to the boundary. For the blast data, the new detail projects down to the bench below the current bench to allow for a better prediction before mining commences on that bench.

Mar 22, 2022

By C Zhang, R Liang, I Canbulat, S Saydam, B Li

The integration of digital twins in mining represents a significant advancement towards enhancing operational efficiency and decision-making. Central to this development is the role of visualisation, a crucial element in mining digitalisation. This paper aims to develop a data-driven visualisation solution for the construction of mining digital twins, highlighting how this innovation revolutionises the representation of physical mining environments. It spotlights the shortcomings of conventional visualisation methods, particularly their inability to accurately depict complex underground environments and their predominantly historical orientation. To address these challenges, this paper proposes a novel, data-driven approach. This approach extensively utilises CAD files, encompassing data from geological surveys to intricate mine plans, thereby significantly elevating the precision of digital twins. It supports real-time updates and enables flexible interaction with a variety of data types. Moreover, it introduces a comprehensive data diagram alongside the adaptation of a 3D tile index. This strategy ensures the efficient rendering of extensive mining environments, allowing for a more dynamic and interactive digital twin model. In conclusion, the implementation of data-driven visualisation in the construction of mining digital twins marks a pivotal advancement in the industry’s digital transformation. It promises a more detailed, accurate, and dynamic depiction of mining operations.

Sep 1, 2024

By A Bonani, R Molina, H Constanzo

With conventional undercutting sequence the infrastructure on the production level often has a short serviceable life before major rehabilitation is necessary and is characterised by high maintenance costs. The abutment stress zone is the main cause of this situation. The application of the pre-undercut caving method variant can increase the availability and utilisation of the production level When a pre-undercut is used development and construction are carried out underneath a previously undercut area, far away from the abutment stress zone, under more favourable stress conditions. This paper describes the design principles and the relevant results from the application of the pre-undercut variant over three years to the Esmeralda sector of El Teniente mine. The aspects described are the undercut-extraction, the undercut-development and construction distances, the geometry and drawbells opening, cave extraction rates, and the rate and height of undercutting.

Jan 1, 2000

During the last 20 years, manufacturers of Australian iron have given increasing attention to development of external markets for processed blast furnace slag. Slag has been in widespread use overseas and data on the performance of Australian slag in concrete lave shown it is suitable for that use. Chemical and physical properties of typical Australian slag products including air cooled, granulated and pelletised slag are discussed and compared with local natural aggregates. Special attention is given to pumping achieve- ments with slag concretes and the observed durability of concrete after many years service. More'recent applications for granulated slag as a sand replacement are discussed. It is concluded that'whilst more wide- spread use of slag is possible, the cost of marketing and transporting slag are likely to restrict opportunities unless for local usage.

Jan 1, 1979

By F Cappuccitti

A colourimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determinations in a campaign at Kennecott Utah Copper Copperton Concentrator (Rio Tinto). Some observations are described, including: frother (MIBC) concentration evolution down a bank, frother distribution between pulp and froth phases, and loss of frother over time due to adsorption on certain minerals. A possible interference with a fuel oil addition was overcome. MIBC in recycle water was also measured. The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimisation of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimise the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.

Jan 1, 2005