Search Documents

By A Roudnev, P Loderer

Mineral froth pumping utilising centrifugal slurry pumps is a major engineering challenge for both the end users and pump manufacturers. The traditional approach has been to oversize the pump for pumping mineral froth. New horizontal slurry froth pump designs offer opportunities to improve froth pumping capability of mineral froth with challenging (high) Froth Volume Factor while maintaining high efficiency, long wear life and stable pumping performance.CITATION:Loderer, P and Roudnev, A, 2018. A reliable solution for pumping mineral froth with challenging froth volume, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 291–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A Creighton, C McKenzie

Blasting is a critical task in the development of an open pit. The formation of stable slopes is also essential to the safe and economic extraction of ore. The objectives of a mine blasting department are often considered to be in direct conflict with those of the geotechnical department. This should not be the case. Personnel in the various mining departments need to understand that their goals are the same û to optimise safety and cost-effectiveness of the operation. Blasting has the potential to damage rock that is to remain in situ by generating either excess vibration, and/or pressure. These damage mechanisms are described and guidelines with respect to blast design to minimise the potential for damage are given. A rock mass could be expected to be subjected to varying degrees of damage by blasting, including both intensity of damage and also the extent of damage. These issues have potential to impact significantly on geotechnical design considerations. It is therefore important for the practitioner to define what constitutes damage. In the context of mining, it is recognised that there is a need to balance the requirements for efficient excavation with those of forming stable and cost-effective pit walls. It is therefore important to have a set of key performance indicators (KPIs) against which the performance can be bench marked. These would include cost and time, both of which may be influenced by very diverse factors such as drilling, explosives and their performance, fragmentation, excavator and haul truck performance, requirements for batter clean-up and safe working practices. KPIs are identified and discussed in this paper.

Jan 1, 2003

The design and selection of components for belt conveyors is a well known procedure and many handbooks, catalogues and design manuals offer a wide range of detailed information which can be applied to most of the known conveyor problems. The aim of this paper, however, is to investigate the various methods of conveyor drive configurations, and incorporate the latest technical achievements in the control systems, particularly for high capacity conveyor systems carrying ore from pit to processing plants where the lowest maintenance, operating and initial costs are of major importance. Past experience has proven that multi pulley drives can reduce initial capital cost of a conveyor; this leads to the need for better torque control during startup, running, stopping and load sharing. Many methods of torque control are available and have been used in the past. All types have their advantages and disadvantages and must be considered when designing a conveyor or conveyor system. However the recently developed solid state electronic soft start controls utilising AC squirrel cage induction motors are gaining acceptance, especially for a conveyor system where the same control and logic system can be used to transmit startup commands to more than one

Jan 1, 1978

Over the past decade most, if not all participants in the resources sector have been involved in initiatives to improve margins, reduce costs and improve business profitability. In many cases the initiatives undertaken have fallen short of their stated objectives, and in some cases have resulted in the terminal decline of the underlying business. In reviewing why many such initiatives fail, a common theme of arbitrary cost reduction and a focus on minimising cost as opposed to maximising value and cashflow emerges. This paper proposes a structured process that allows mine owners and managers to develop an understanding of their cost structure and optimise production and cost outcomes from the business. The broad objective of cost optimisation is to create value by getting more out of existing and new assets by focussing on operational areas, particularly production and maintenance. The paper uses practical examples to highlight the application of cost driver trees as a mine improvement tool.

Jan 1, 2002

In 1969, Queensland Mines Limited obtained two large Prospecting Authorities in Arnhem Land, Northern Territory, Australia. The Nabarlek uranium deposit containing some 12 000 t of U308 was discovered on one of these in June 1970. Mining and stockpiling of this deposit were completed in 1979 and processing to yellowcake, which commenced in June 1980, is expected to occupy an 8-10 year period. The continuation of exploration, essential for the company to become a longer- term producer, was inhibited in 1972 by a Federal Government "freeze" on exploration in Aboriginal Reserves in the Northern Territory. Subsequently, the procedure for explorers to gain access to exploration areas in Aboriginal land was radically changed by the proclamation of the Aboriginal Land Rights (Northern Territory) Act 1976. As a result of this Act and the associated administrative policies adopted by Governments, Queensland Mines Limited has not yet regained access to the exploration areas it formally held in the early 1970's.

Jan 1, 1986

The Henty Gold Mine is a good example of a situation where conditional simulation and optimisation techniques may have useful impact on modelling of mineralisation distribution and ore definition. Much of the gold mineralisation at Henty is concentrated within an alteration zone which is both physically discontinuous and forms only a small fraction of the overall mineralised volume. The alteration units are mappable from diamond drill core and underground workings. Conditional simulation and optimisation techniques for ore definition have found considerable success in the open pit gold mining environment. For many reasons including computational efficiency, lack of consistent geological information, and lack of familiarity with ideas and methods among mine geologists, implementations of these methods in open pit mining have been comparatively simplistic. Modelling is commonly reduced to treating the sample data as a single geologic population. This paper discusses the application of the MP method (a particular implementation of conditional simulation and optimisation) to modelling the distribution of potential ore blocks in the Henty gold mineralisation. The approach allows the mine geologist to model both the spatial geometry of the alteration types and the gold grades associated with each alteration type in a single process. Options allow the geologist to include or exclude underground geological mapping and face sampling depending mainly on the abundance of drill hole sampling and the quality of the face sampling. An optimisation algorithm based on maximisation of profit from mining is used to assist in ore definition.

Jan 1, 2000

By Manula C. B

The total systems model for underground oal mining planning and design is a set of omputer programs which encompasses a realis- ic reproduction of the interaction between he geological, environmental, equipment, meth- ds and the health and safety aspects of the ining plan. The total system includes nine ajor subsystems - Geology and Reserves, Meth- ne Generator, Roof Support, Subsidence, Pro- uction, Rail Haulage, Cost, Water Generator, nd Ventilation. The subsystems themselves re divided into two categories based on the requency with which they are executed. Event riented Subsystems are executed either inde- endently, or at discrete intervals when cer- tain specific events occur. Dynamic subsystems 'unction interactively during the production :ycle. They transfer data to or request data `rom event oriented subsystems only when spe- ific events occur. Three specific areas for iodel application are in the measurement of system performance, the development of the '_ nterrelationships of the components of deep Wining process and the evaluation of new and Lnnovative mining technology.

Jan 1, 1977

The correct design and effective operating strategies of metallurgical plants require a constant analysis of data gathered for process control, or for due accountability. Conventional, oldfashion statistical tools often fall short of helping management, either because they are too complicated and ambiguous, or because they fail to address structural problems leading to causes of setbacks. This paper focuses on three statistical tools known for their practicality and the in-depth perspective they offer in attempts to retrieve important information from existing data. These tools also provide a better appreciation of the importance of carefully selected data quality objectives. Chronological data are meticulously gathered and stored at considerable expense: They have value, and it is the duty of management to take full advantage of them. These three selected tools are the variogram and its auxiliary functions, the moving average and its auxiliary functions, and the relative difference plot. This paper offers solutions, and a reference for managers to optimise metallurgical plants.

Jan 1, 2002

By E Topal

There are presently no suitable underground mine production scheduling optimisation models available for application to sublevel stope mining. Scheduling underground production for maximum return is therefore still a manual process, which generally involves scheduling production from the next available highest cash flow stope within the operational constraints of the project. In most mining operations, the scheduling problem is too large and complex to guarantee truly optimal results through manual scheduling. This paper reviews some general optimisation studies that have been proposed for underground hard rock mining. Furthermore, an example of a mixed integer programming model is presented for a small conceptual sublevel stoping operation. Comparative results of a schedule generated by a mixed integer programming (MIP) production scheduling model and a manually generated model on a nine stope example is presented. Results indicate that the potential benefits of the MIP production scheduling model for the purpose of maximising NPV are significant. Finally, a new constraint was formulated to limit multiple exposures of fill masses for use in an existing MIP production scheduling model. Testing of the formulation took place on the central stope of the nine stope example, which showed that the formulation performed its task without breaking other operational constraints.

Jan 1, 2007

Human creativity springs from the natural desire of mankind to know and its capability to learn. Explorers and discoverers possess these features in a high degree. They are driven by an unrelenting curiosity to go beyond the boundaries of the known, to explore into the nature of things, to reveal connections between ideas, facts, conceptions, to view things from new angles, to change perceptions. A well-known fact about the construction industry - and underground construction in particular - is that all projects are unique. The degree of complexity due to the intertwining of the variety of project-related parameters is higher than in many other industries, thus forcing contractors as well as suppliers to be truly adaptable and flexible. The enormous advantages of shotcrete as a construction and rock support process and the improvement of materials, equipment and application know-how have made it a very important and necessary tool for modern underground construction works. The development of modem wet shotcreting in particular has enlarged the field of underground construction work. Projects that were impossible to be realised, have now become practicable. Subsurface structures can be placed where they are needed, without regards as to rock and soil conditions.

Jan 1, 1995

By Ellis WK, Greenwood-Smith R

A nuclear technique for the analysis of copper in bulk materials has been developed and successfully field tested at Mount Isa Mines Limited. The technique utilises the gamma-ray resonance scattering process. A bulk analyser based on this technique gives a rapid and accurate measurement of the percentage by weight of copper or nickel aver- aged over a large mass of sample, typically 20 kg. The only sample preparation required for accurate analysis is crushing to -2.5 cm. At Mount Isa over 100 mineral samples covering a wide range of rock types and copper contents were analysed. Bulk analyser assays and chemical laboratory assays agreed closely for underground pillar-extraction and geolog- ical chip samples, conveyor belt samples, and finely ground samples from the ore concentrator. For the concentrator samples, the root mean square deviation between bulk analyser and chem- ical laboratory assays was 0.06 wt.% copper. The chemical assay errors for these samples were about 0.06 wt.%

Jan 1, 1975

In an earlier paper(l) details of a laboratory method of extracting and separating tantalum and columbium oxides from tantalite have been given. In view of the fact that Australia may have need to be self sufficient in this field it was decided to erect a pilot plant for the production of tantalum oxide in the Metallurgy School, University of Melbourne. The plant was designed for treating about 40 lb. of ore in a batch over a period of two weeks, although; because of the sectionalized nature of the process, the capacity of the plant was 40 lb. ore per week.Australia is fortunate in possessing some very rich tantalite and columbite deposits, particularly in the Pilbara District in Western Australia. The ore used in this work was obtained from a small but high grade deposit near Greenbushes, Western Australia, and consisted of lumps, weighing up to 8 lb. each, of almost pure ferro-tantalite with occasional thin veins of the very' rare' mineral stibiotantalite.The main constituents were:

Jan 1, 1946

By Royston D

Victoria has an extensive brown coal resource, 202,000 Mt, of which 43,300 Mt is regarded as readily recoverable. This brown coal is located principally in the Latrobe Valley as thick seams and is being extracted at low cost primarily to support base-load electrical power generation. The high moisture content of the coal is partially off-set in many applications by the high reactivity of the coal and the generally low levels of potential pollutants such as ash, sulphur and nitrogen in the coal. Large scale development of this brown coal resource began in the 1920's. In addition to electricity generation, it is used for briquette production, carbonisation of briquettes to char and was gasified for town gas supply to Melbourne (1956 - 1969). The BCLV coal to oil pilot plant at Morwell is a major new initiative in the use of Victorian brown coal. Many other new developments are in place and emerging in the utilization of low rank coals. Examples of these developments are, the large-scale gasification of lignites in the USA, and value-added products such as bulk chars, solid fuels, activated carbons and coal-water mixtures. The Government of Victoria has created the Coal Corporation of Victoria to promote current sales of briquettes and to encourage further new industrial developments based on the State's brown coal resources, in particular the Loy Yang coalfield. The Coal Corporation also has a vigorous product and process oriented research and development Programme.

Jan 1, 1987

Economic and technical reasons forced the mining industry all over the world to increase the unit size of mineral processing equipment. in large flotation cells, this development leads to problems in areas of air dispersion and keeping solids in suspension. Outokumpu, an operating mining company, designed and developed a mixing mechanism for large flotation cells at its own concentrators and also studied problems related to tank design. Ideal conditions for flotation can only be achieved if the flow pattern created by the mixing mechanism fits well into the tank configuration and the risk of short circuiting is minimized. In large deep flotation cells, four different zones can be found which improve the behaviour of large cells when compared to small cells. Selectivity is increased and in some cases final concentrate grades can be produced from the rougher cell. The largest units have also been used as final cleaners in some installations. When modernizing old plants by installing fewer larger flotation cells, immediate and substantial savings in power consumption are achieved. Additional power savings are made in pumping costs because of simpler circuit design and decreased circulating loads

Jan 1, 1978

By R W. Wilson, A R. Branch, T S. Pooe

The original bulk air cooling system at this particular mine made use of two water chilling refrigeration machines to produce peak cooling of approximately 12 MWR with a downcast air temperature of about 7°C; however, as the shaft is not used for transporting personnel, the opportunity existed to supply more cooling to the mine by lowering the downcast air temperature. An ice storage facility has been constructed and provides a range of opportunities in operating the system: colder air temperature sent to the shaft, enabled by using near-zero degree water produced by melting ice to cool the air; electricity time-of-use management, by shifting electricity usage out of peak tariff periods; and increased peak cooling capacity, by melting ice while chilling water. Ice is created in the storage facility at night while the ambient air temperature is low and then melted to produce cold water when required by the cooling process. An ice dam was constructed and serpentine stainless steel coils installed where the ice is produced; one of the refrigeration machines was converted to chill a glycol solution to subzero temperatures to create the ice on the coils; a plate heat exchanger was installed to allow the glycol chiller to act as a water chiller as well; and a third spray stage was added to the bulk air cooler to utilise the near-zero water. This paper describes the thermodynamic design, construction and performance assessment of the new system, which is unique, novel and represents the state-of-the-art of this type of cooling system and energy management.CITATION:Branch, A R, Wilson, R W and Pooe, T S, 2015. Novel use of ice thermal storage for energy management on a mine refrigeration plant, in Proceedings The Australian Mine Ventilation Conference, pp 185–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

Traditionally, the term ætotal systemÆ design applied to comminution conjures images of a design that addresses the usual business and operational drivers, including health, safety and environment (HSE), capital cost, operating cost, throughput and product size. In terms of the physical process, the mine to customer type studies also exemplifies an approach that satisfies a normal ætotal systemsÆ approach. As an industry there are drivers that are forcing a re-consideration of what we regard as our total system. This modification of drivers will require changes in approach and implementation to provide the best solutions. Some of the major changes that impact the drivers are shortage of skilled personnel, changing social attitudes to remote mine site work, greenhouse gas emissions (GHGE), quality of available orebodies and geographical location of new mine sites. One approach to the challenges presented by the changing business environment is to expand the system envelope around comminution to ensure that comminution, in its widest sense, helps to meet the new realities. Background to the new drivers and constraints is provided and some of the appropriate responses are examined in relation to the impact on the total system.

Jan 1, 2007

An efficient stores organisation is essential for an efficient undertaking. Unless the stores organisation is able to meet the requirements of its requisitioners promptly and economically, the undertaking as a whole cannot function efficiently.Delays or errors in supply of material, or substitution due to lack of material availability from the stores are costly and must be eliminated. This then makes the objective of a store, to supply on demand at the cheapest possible price, those items of stock which it is organised to carry, also to procure as quickly as possible and at the lowest price those special items required which are not normally carried in stock. To do this it is necessary to set up a stores organisation consistent with the size and requirements of the undertaking. Stores organisations vary with the nature of the undertaking they are designed to serve. In the case of the Broken Hill Associated Smelters Pty. Ltd., an organisation has been established to meet the operating and maintenance requirements of the Port Pirie Works. These embrace the particularly wide range 0:1; activities associated with roasting" blast furnacing and refining the lead concentrates from the Broken Hill Mines in a continuous metallurgical process producing a variety of refined metals; also many associated activities including power production and engineering maintenance and construction.

Jan 1, 1951

By Abdulhadi H. M, Soliman S. A

The Western Desert of Egypt is a part of the arid Great Sahara of Africa which extends from the Nile Valley in the east to the Atlantic Ocean in the west. It is covered by a sedimentary sequence of Mezozoic and Teriary rocks. Recently this part of the country (about 65% of its surface area) has attracted an increasing attention in the plan of finding new agricultural and industrial communities outside the crowded Nile Valley. The plan aims to reduce the high population density in the narrow Nile Valley and to cover a considerable part of the increasing food demands in the country of Egypt. Accordingly, the groundwater exploration work in the Western Desert has been remarkably increased in the last decade, however it is still limited compared with the vast area of the Desert. The present work is a part of the groundwater exploration in the 6th October City, a new community located at 40kms west of Cairo. The rock exposures belong to a sedimentary stratigraphic section starting from the Cretaceous in the east to the Pliocene in the west. The Cretaceous outcrops due east are attributed to an almost N-S uplift and forms a thick massive limestone plateau which separates the present area from the Nile Valley. The Teriary section in the west have alternations of different porous formations such as the sands and sandstones which may acquire a good potentiality of groundwater resources. The previous groundwater exploration work included combined geological and geophysical investigations followed by exploration drilling. Although the area lies directly to the west of the Nile Valley, the discovered groundwater is saline and located at deeper reserviores compared with the groundwater in the Nile Valley. This groundwater was described as marine fossile water by the oil companies working in the Western Desert. From the geological point of view, it is believed that the Cretacious massive limestone plateau, in the east, roots to a depth which far exceeds the groundwater levels in the Nile Valley and acts as an impervious barrier between the aquifers in the Nile Valley and the area under investigations.

Jan 1, 1988

Uranium minerals were found in Australia as early as 1869, but it was not until the 1940's that a search specifically for uranium was begun. Instrument types and techniques used in early exploration are still used today, but have been developed into more sophisticated and portable types. Recent improvements in exploration have been the introduction of the gamma ray spectrometer, radon sampling and geochemical surveys. The environments of presently defined uranium deposits are predominantly sedimentary. Known deposits in igneous environments are usually small. The size of targets which are likely to provide economic deposits is of the order of 10,000 tons U308, producible at a cost of less than $10 per pound. Such targets are most likely to be in Precambrian sediments or in granitic masses. Recent exploration in Australia has included investigation of Precambrian sediments, Precambrian and Palaeozoic granites, Mesozoic and Tertiary sediments, Precambrian volcanic rocks and brecciated masses of unknown age. The origin and method of emplacement of uranium in these environments is not well known but there are indications that syngenetic sedimentary processes are important, and volcanic rocks may make a major contribution to the supply of uranium.

Jan 1, 1970

The Ok Tedi copper and gold mining project is located in the headwaters of the Fly River system in western Papua New Guinea. The project's Feasibility Study was completed in 1979, and in- cluded a preliminary environmental assessment and an environ- mental management program. Construction commenced in 1981, an environmental impact study was completed in 1982, mining and treatment of gold ore commenced in 1984, staged construction of copper ore processing facilities took place during 1986-1988, and a further major environmental study was carried out for the operat- ing mine during 1986-1989. A very considerable data base of environmental information has been assembled by means of a comprehensive monitoring program. Environmental management criteria applied to the Project have reflected the stages and nature of development and operation. Criteria have been designed to regulate potential environmental impacts in the Fly River. An Acceptable Particulate Level of suspended sediment is the principal criterion. Compliance is con- ditional upon -a limited reduction in fish biomass, and upon dis- solved and particulate copper concentrations not exceeding predicted values at various locations throughout the river system. The criteria were established by the Government of Papua New Guinea following evaluation of environmental studies undertaken by the mining company. Compliance is checked by a detailed monitoring program, frequent reporting and statistical evaluation of monitoring results.

Jan 1, 1991