Search Documents

The competitiveness and future growth of the Australian mineral resources industry face a number of challenges. The paper addresses key factors likely to influence the attainment of high performance and continuous improvement including organisational leadership, management/employee relations, technology, safety, health and the environment. Business practices such as benchmarking, Total Quality Management and re-engineering to achieve process and performance improvements are commented on. Future success for the industry will largely hinge on global business skills, a sustained focus on Quality principles and achieving performance through people.

Jan 1, 1997

By R-H Yoon

Increasing the upper particle size limit of flotation would allow operators to increase mill throughput, save operating costs, simplify flow sheets, and increase rate of return. However, coarse particle flotation is difficult for various reasons, of which bubble-particle detachment has been identified as the major limiting factor. In the present work, the process of bubble-particle detachment has been studied by directly measuring the forces required to detach air bubbles from hydrophobic solids. The measurements were conducted using a hanging balance apparatus. The measured forces were converted to detachment energies that can be compared with the work of adhesion, which in turn is a function of hydrophobicity, surface tension and contact area. The results were converted to detachment energies using the Young-Laplace equation for capillarity. In the present work, the solid surfaces were hydrophobised by coating them with octadecyltrichlorosilane and cetyltrimethylammonium bromide. The results show that bubble-particle detachment occurs in two steps. In the first step, air bubbles are deformed, while the three-phase contact (TPC) line is pinned, until contact angle reaches advancing angle. In the second step, the TPC line moves along the surface until solid/air interface is replaced by solid-liquid interface. In general, the energies of detachment measured in the second step are in good agreement with calculated work of adhesion. Thus, the energy required during the first step effectively represents an energy barrier for bubble-particle detachment. It has been found that the energy barrier varies with surface roughness and surface tension. The results of the present investigation suggest, therefore, that coarse particle flotation can be improved by control of particle hydrophobicity, surface roughness, and surface tension.

Jan 1, 2005

By T Baard, A Pieters

This paper deals with the design and implementation of a 17 MW (nominal) surface cooling installation at Impala Platinum No 14 shaft located in Rustenburg, North West Province, South Africa.The cooling requirements included the installation of a surface ammonia refrigeration plant complete with the storage of hot and cold mine service water for underground use. It was also necessary to install a surface bulk air-cooling facility, which cools 400 kg/s of ventilation air going to the underground workings. Primary cooling is to the surface bulk air cooler. The cooling duty of a surface bulk air cooler is heavily dependent on the ambient wet-bulb temperature. Because of the daily wet-bulb temperature variation in this part of the world, use was made of a cold thermal storage facility of four million litres. The excess chilled water is stored during the night, for use by the main drilling shift during the day. This keeps the refrigeration machines as close as possible to full load during the summer, thus maximising the use of the capital expenditure. This paper discusses the control philosophy used to maximise the cooling output, as well as the thermal process. The project consisted of two phases resulting from the underground development phases of the mine. The first phase started in January 1999 and was commissioned by the end of the same year in record time. The final commissioning of the second phase took place at the end of 2002. The most difficult part of the construction phase was the tunnelling of a subsurface air duct from the bulk air cooler to the operating vertical shaft. This was done without disruption to the hoisting of men, material and ore in the shaft. Owing to the size of the refrigeration machines, the ammonia quantities involved and the application on a mine (no ammonia can go underground, either in the service water or in the mine air) special precautions had to be taken. South Africa has developed high standards for ammonia refrigeration plants used on mines, which will be partially dealt with in this paper.

Jan 1, 2005

By Brasnett TC

A wide variety of problems are encountered on a day to day operating basis in the Isa Mine Concentrators. These vary from complex textural problems in the lead-zinc concentrator and their subsequent effect on grinding and flotation to scheduling of converter slag treatment in a chalcopyrite concentrator. With the advent of process control, metallurgists need to specialise and keep up to date with technology improvements. This paper will attempt to describe the significant problems'faced by a Metallurgist û Control.

Jan 1, 1978

By T. Baker

The Eloise Cu-Au deposit is 60 km SE of Cloncurry in NW Queensland and has a current indicated reserve of 3.2 Mt @ 5.8 per cent Cu, 1.5gA Au and I9g/t Ag. It is hosted by metasediments and metabasic rocks that underwent amphibolite facies metamorphism at 550-600¦C and less than 3.5 kb. Peak metamorphism coincided with the regional D2 event which produced an S2 foliation with north-south strike and variable sub-vertical to steep east or west dip. The deposit is associated with several major shear zones parallel to the S2 foliation. The lodes form part of a large alteration system that is localised by the retrograde shear zones. Homblende-biotite-quartz with minor sulphides occur early in the alteration paragenesis which is overprinted by chlorite-muscovite-pyrrhotite-chalcopyrite ¦calcite+¦nagnetite. The later assemblage replaces the earlier Fe-K alteration as well as Fe-rich metamorphic assemblages such as homblende, biotite and staurolite indicating a post peak metamorphism timing for ore formation. Although replacive textures are the most common, the alteration can display open space infill and brecciation as well as durchbewegung and mylonite textures indicating that mineralisation occurred during ongoing ductile deformation. All these features are crosscut by a later brittle phase of calcite-chlorite-quartz¦pyrite alteration.

Jan 1, 1994

By Wright D. J

Successful heap leaching depends on three major factors: 1. Chemical conditions appropriate for the dissolution of the valuable metal; 2. Contact between the leach solution and the valuable metal particles; and 3. Movement of the leach solution through, and out of, the heap. Given that appropriate chemical conditions can be provided, and the individual particles have sufficient permeability to allow solute/solvent contact, the problem of getting the solution to and from the particles remains. Non-uniform percolation of solution throughout the heap, caused by the presence of fines, is a common problem which occurs, to some extent, with all heap leachable ore. The conventional solution to this problem is agglomeration, which involves the attachment of fine particles to larger particles, effectively modifying the size distribution by preventing the fine particles from acting on their own. While agglomeration must be considered as an extremely effective technique with virtually no limit to its application from a technical point of view, its application is limited by economic considerations. A new technique has been developed which is not only a low cost alternative to agglomeration, but also has the potential for enabling the application of low cost heap and vat leach techniques to a significantly wider range of ores than current practice would suggest. The new technique, known as Electrokinetic Leaching, utilises electro-osmotic flow to enhance percolation through the heap. This paper describes and presents results of the laboratory testing, pilot heap operation and commercial application of Electrokinetic Leaching of a low grade gold ore and a tailings deposit. Comparative cost analyses between conventional and the alternative processing techniques are presented.

Jan 1, 1994

By B Veera Reddy

For thick seam extraction, the Blasting Gallery (BG) method is ideal for obtaining the maximum percentage of extraction at fast rates. The continued use of this mining method is threatened by strata control and spontaneous heating problems. The strata control problems are managed, to some extent, by supporting the roof with cable bolting and roof bolts of 2.5 m length and with regular induced blasting. However, a number of BG panels were sealed off prematurely due to spontaneous heating problems, losing 1.12 million tonne of coal. The use of compressed CO2 for controlling mine fires is not uncommon in the coal mining industry, but its use is something new for controlling active spontaneous heating in a BG working panel goaf. This method was attempted at the BG I/8 panel of the Godavarikhani (GDK) 8 Incline, Singareni Collieries Company Limited (SCCL). The spontaneous heating was effectively controlled and the remaining coal in the panel was completely extracted by continuous flushing of carbon dioxide (CO2) into the goaf for 40 days. One thousand and twenty four CO2 cylinders, each of 45 kg at 80 bar pressure were flushed into the goaf at the rate of 25 to 30 cylinders (350 m3 of CO2) per day. A quantity of 35 510 tonne of coal was extracted during the period from 30 July 2002 to 7 September 2002. The main objective of this paper is to present the complete process of controlling the spontaneous heating by CO2 flushing and to report on the study of the behaviour of gases and their analysis. The unique experience of controlling the active spontaneous heating in the working Blasting Gallery I/8 panel goaf at GDK 8 Incline with CO2 flushing (till the completion of the panel) will go a long way in establishing a working procedure for handling fire/spontaneous heating problems in BG panels.

Jan 1, 2005

The investigations of the Leningrad ruining lilstitute on this problem are carrying out in the following main directions: 1) The analysis and study of contaminants migration at particular sites of mining development; 2) The working out of theoretical and me- thodical basic principles of aquifers migration tests; 3) The work- ing out of methods of the forcasting of groundwater pollution pro- cesses; 4) The theoretical and uethodical substantiation of hydro- geological observations of groundwater pollution processes; 5) The wort ing out of the measures at the groundwater control and their rational use at the particular sites of mining development. The research that have been carried out by the present moment have covered the wide range of wining and geological conditions -- as from the point of view of specific genetic types of water-be- aring rocks (porous, fissured and fissured-porous), as well as from the point of view of pollution sources (surface waste water basins and underground basins of non-standard water) and the cha- racter of the latter's migration (tracers, physically neutral ef- fluents, heavy or light ones). The combination of specialized mi- gration tests and observations carryed out at uoayi, sites, as well as the following ar~,alysis o:i the data of field study allowed to get useful theoretical, methodical and practical results on the all directions above mentioned, ns the summing up of these results the author proposed the concept of controlled ground :ester polluti on. This conception is based on three whales" - groundwater self- purification, engineering prevention measures and ground-water monitoring correlated with each other by succes i.vely refined (ac- cording to the observation data) hydrogeologicZl forecasts.

Jan 1, 1988

By J Cook, S Pike, D Pridmore

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The application of high-resolution seismic reflection to map structure and/or mineralisation in hard rock environments has progressed significantly in the last decade. Improvements in equipment, field practice, processing and understanding has seen the seismic reflection technique emerge as a cost-effective tool for high-resolution three-dimensional structural and lithology mapping to depths far greater and with superior accuracy than other more conventional geophysical techniques.This paper outlines results and preliminary interpretation of 2D and 3D seismic reflection surveys aimed at defining fault zones and locations for quartz load development in favourable host lithologies at the Cracow low-sulfidation epithermal gold system in Queensland, Australia.As this is possibly the first time that high-resolution seismic reflection data has been used to define the structurally-controlled location of low-sulfidation epithermal gold mineralisation, an important aspect of this work was the derisking or due diligence steps taken prior to commissioning the full 3D surveys at each site. This included full wave sonic logging, vertical seismic profiling and trial 2D lines. Interpretation of the 2D profiles and the drilling of interpreted structure provided the confidence to proceed with the full 3D survey.The advantage of collecting 3D data extends beyond ensuring that the received reflections are located correctly in 3D space. The final 3D data cube can potentially map the entire fault network, thus highlighting flexures and changes in orientation of the structures both vertically and along strike, which is an important aspect in the deposition of gold and for direct targeting.CITATION:Smith, R, Cook, J, Pike, S and Pridmore, D, 2015. Application of high-resolution seismic reflection surveys to exploration for blind vein systems at the Cracow low-sulfidation epithermal field, in Proceedings PACRIM 2015 Congress, pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The sole reason for a mine to exist is to extract the finite mineral resource. Accurate grade control is critical to the economics of any mine. If grade control is not optimised, then no matter how good the downstream processes are, the full potential of the operation will not be realised. The detailed implementation of grade control varies but typically consists of sampling and assaying to determine the location of the ore zones. A lot of time, money and effort are spent defining the location of the ore as accurately as possible à but then it is blown up! The effect that blasting has on grade control is rarely adequately accounted for when the rock is excavated because there has never been an accurate and practical method for measuring blast movement. This paper draws on over six years of research into measuring and understanding blast movement, which started at the Julius Kruttschnitt Mineral Research Centre (JKMRC) of the University of Queensland. The research has made a unique contribution to open pit blasting by helping to develop a practical tool for measuring blast movement, which was then used to improve the understanding of three-dimensional blast movement dynamics. However, these achievements would be of largely academic interest without taking the final step of using this technology and knowledge to account for blast movement by translating the ore polygons in response to the measured movement vectors. This paper provides an overview of blast movement but focuses on one site where blast movement was measured during three separate periods, with significantly different orientation of the mineralisation on each occasion. The theoretical ore loss varied from nine per cent to 24 per cent. The differences are primarily due to the orientation of the ore polygons relative to the direction of movement. The optimum grade control solution is a combination of accurately accounting for blast movement and designing appropriate blasts.

Jan 1, 2009

Predictive chemical models facilitate the selection, design and assessment of aqueous chemical processes. The development of expertise in aqueous themochemistry has not matched the explosion in computer technology for modelling, which has placed pressure on the need for acquisition of skills to critically assess the appropriateness of the models produced. The 'blind faith' culture which appears to be developing must be arrested by appropriate programs at the tertiary level and professional development strategies in the minerals industry.

Jan 1, 1996

By A Robertson

Australia has been slow in adopting the use of underground space as a part of our urban planning process. Australia has one of the highest levels of tunnel advance per capita per annum in the world, yet the use of underground space in our cities appears difficult for our planners and politicians to comprehend, not withstanding the general availability of good quality rock and contractor expertise in Australia. However, the lack of space in our urban areas is being highlighted as our major cities expand outwards and people and businesses gravitate towards city centres. Typical potential underground space uses include car parking, self-storage and archiving facilities, water storage, underground quarrying, small industrial facilities and another layer of traffic (electric and fuel cell) and services network. Historically, blasting in high density population areas has resulted in blast vibrations and blast overpressures exceeding the limits, which in some case have been set extremely low in terms of peak particle velocity (PPV). This makes conventional blasting difficult, often requiring low charge weights per delay and associated small blast sizes and slow advance rates. However, the introduction of new technologies, such as computer aided drilling, electronic delays and low-energy explosives has made this task considerably easier. Although more expensive than conventional blasting, excavation by blasting using these products and technologies in relatively good quality ground is believed, in most cases, to be less than the cost of mechanical excavation. In this paper, the authors look at innovative trends in underground quarrying, underground commercial space and tunnelling and put forward their concept of future excavation demand, future product requirements and technical specifications to the drill and blast community.

Jan 1, 2007

By M Pratt

For up to 75 years large scale coal mining has been carried out within the Latrobe Valley region of Victoria. Withdrawal of groundwater from Tertiary aged sediments within the Latrobe Valley is essential to allow coal mining to proceed to depth. Water within the overburden layers, coal seams and interseams must be drained to avoid flooding during the mining process. The pressure in deeper aquifers must also be lowered to avoid floor heave, batter instability, and to maintain safe operating conditions as the mines develop in size and depth. The cost-effective management of the groundwater systems at and adjacent to the mining operations in the Latrobe Valley is essential to enable the efficient utilisation of the coal resource whilst minimising the environmental impact of this major industry in rural Victoria. Large-scale depressurisation and dewatering programs within the Latrobe Valley mines are managed through the use of detailed groundwater management plans. These incorporate:an extensive monitoring network which extends up to 60 kilometres from the mines; detailed mine scale and regional groundwater and hydrogeological models; and established operational procedures aimed at minimising capital and operational costs associated with the mine groundwater systems. Groundwater extraction system optimisation programs have been introduced into two of the mines with the aim of reducing extraction rates, improved risk management, and reducing operational costs by approximately whilst not compromising mine safety. This paper reviews the aquifer depressurisation and mine dewatering operations of the Latrobe Valley mines and illustrates the techniques utilised to ensure that high artesian pressures do not adversely impact on the mining operations.

Jan 1, 2003

Gold mineralisation at Wapolu lies within an exposed arcuate zone at the decollement contact between a basement dome of high grade metamorphics and an overlying ophiolite sequence. This contact was originally a thrust fault which has since become a decollement zone for gravity sliding in association with basement doming. Hydrothermal models for the gold mineralisation postulate an epithermal system in which fluids were channelled up the decollement with boiling of those fluids causing hydrothermal brecciation and subsequent gold deposition. The alteration assemblages, fluid inclusion data and geochemistry indicate that the upper levels of the system are exposed.

Jan 1, 1987

Historical exploration of the Ballarat East goldfield defined two primary quartz vein lode types. Tracking the intersection of these lodes with vertical lines of enrichment (or so-called æindicatorsÆ) was the basic practice for historical mining. This strategy proved highly successful in terms of identifying quartz veins associated with mineralisation. However, it provides little understanding of the timing or processes involved in the formation of these veins, or the associated emplacement of gold. Current underground mapping shows the Ballarat East gold deposit can be subdivided into four stages of vein formation. The earliest veins (V1 and V2) strike north-south and formed during bedding flexural slip and limb thrust fault propagation in parasitic chevron folds. V3 veins are subhorizontal and relate to further fold tightening involving a transition from east-west compression to north-south extension that initiated re-shear of bedded slip surfaces and additional strike-slip faults. Sporadic V4 veins overprint the shallow-dipping sections of V2 and V3 veins and are associated with weak north-south compression. The V4 veins mineralogy is distinguished by a high carbonate content and sphalerite-galena sulfide assemblage. Vein sampling indicates a significant increase in gold mineralisation where overprinting by the later deformation/veining has occurred. As a result of these observations, a new model is emerging that identifies the chronology, structural control and spatial distribution of respective quartz vein types. This is a major advance in terms of exploration targeting, resource modelling and mine planning.

Jan 1, 2008

By A Cooper

The current financial climate has given rise to fears that falling mineral prices and tight credit will force mining companies to cut back on production and new project development in a bid to cut costs and conserve cash. However, a prolonged squeeze on global supply can have only one result: a massive and potentially explosive demand for metals in the not-too-distant future. A resurgent global economy will also generate dramatic new demand for oil and energy, with a return to higher oil prices likely. How then should the mining industry plan for the future? In-pit crushing and conveying (IPCC) could lead the way as a partial or complete substitute for trucks. In 13 of 15 studies undertaken by Sandvik and Snowden, comparing IPCC with truck-optimised pit designs, IPCC generated operating savings ranging from US$0.18 to US$0.82 per tonne moved, compared to trucks. Trucks have higher operating, maintenance and energy costs than conveyors. New emission standards on diesel engines may make them more emission friendly but less efficient in terms of energy usage. With far more efficient energy use and cheaper operating costs per tonne moved than trucks, conveying offers an attractive alternative for the bad times ahead and into the apparent energy depleted future. When evaluating alternatives, a reasonable first step would be to conduct a scoping level study which analyses the differences in capital and operating costs between a truck and shovel operation and an IPCC solution. The study can also determine what type of IPCC is best suited to the particular mining application. The results can then be used to decide whether a more detailed study is justifiable. IPCC is a proven process that, with a fresh mindset, can make a significant improvement to mining operations. Sandvik (as an OEM with a full suite of IPCC equipment) can undertake these studies in ten working days in conjunction with Snowden or any other independent mine planner who knows how to schedule for IPCC. Because most mining industry personnel have been æborn and bredÆ on trucks and shovels û this paper focuses on some of the practical considerations necessary to make IPCC systems work that the Sandvik Technical Services Group has encountered during these studies.

Jan 1, 2009

The known coal resources of South Australia are either of poor quality, or expensive to extract, or both. Export quality coal occurs only at great depth in the remote north of the State; the balance of the State's coal resources are suitable only for local electricity generation. Currently there is only one coal mine in the State, at Leigh Creek. This provides fuel for approximately 34% of the State's electricity generation, the balance being fuelled by natural gas. In the near future, new fuel sources must be developed to augment diminishing supplies of natural gas, and to cater for increasing demands for electricity. The South Australian Government has determined that future electricity generation will be based on the combustion of local coals. The geological and geographical environment of the known coal deposits and the quality of these coals are such that the most up to date and innovative technology must be applied to both extraction and combustion processes. The Government, the Electricity Trust of South Australia, and several Australian and overseas companies have embarked on an extensive research and development programme to ensure that these otherwise useless resources can be developed to the benefit of the State.

Jan 1, 1987

By D V. Bright

Oroya Mining LimitedÆs Mt Gibson Gold Project, 280 km north east of Perth, is one of Western AustraliaÆs more recent discoveries of a major gold resource. Modern gold mining commenced in 1986, on a shallow laterite reserve of 6.62 million tonnes averaging 1.50 g/t gold. By the end of 1998, mining had progressed from an initial three shallow laterite pits to a series of 14 open pits with maximum depth of 100 m, on three separate trends with a combined strike length of over 10 km. The Project has yielded 868 400 ounces of gold from 16.5 million tonnes of ore at an average recovered grade of 1.64 g/t gold, from near surface laterite, supergene and primary sulfide ores. This includes a 160 m deep underground decline operation which mined 120 000 tonnes at an average grade of 9.1 g/t gold and a four million tonne Dump Leach on a synthetic base which yielded 68 900 ounces. The Project was placed on Care and Maintenance in 1999 pending drilling to refresh reserves. Hosted by strongly tectonised and altered Archaean volcanic rocks within and adjacent to a major regional shear, primary gold mineralisation occurs as structurally emplaced sulfide and quartz lodes. On the main Gibson Trend, multiple zones of mineralisation occur within a zone up to 600 m in overall width. The overall footprint of known mineralisation exceeds 20 km2 and the potentially mineralised domain exceeds 100 km2. The current estimate of a combined resource of 9.4 million tonnes averaging 2.47 g/t gold (749 500 ounces) is derived from a database of 10 500 drill holes, of which only four per cent test below 100 m vertical depth. Ore envelopes which remain open at depth and major gaps in the drilling pattern beyond the currently defined resources promise straightforward potential to define additional resources. Oroya Mining Limited and its joint venture partner Barrick Australia are targeting a major gold mining operation from this potentially world-class mineralised system. Oroya has the exclusive right to produce up to 500 000 ounces and is working toward the completion of a feasibility study into a resumption of mining using the existing 1986-built 1 Mtpa processing plant. The joint venture is in the early stages of testing the depth and lateral potential of the Mt Gibson mineralised system. Mining options currently under review include progressive open pit extension and amalgamation leading to one or more large open pits, and underground operations. It is too early in the development of the Project to offer definitive economic models of potential large-scale mining operations.

Jan 1, 2003

By J Leppinen, B Johanson, R Kalapudas, G McMahon

The Suurikuusikko gold deposit was discovered in 1987 in western Finnish Lapland, 54 km NNE from the town centre of KittilS in the volcanic belt of Central Lapland. It is hosted by tholeiitic basalts in a graphite-bearing albitite breccia. The ore is located in subvertical shear zones characterised by strong albitisation, carbonatisation and sulfidisation. The ore minerals consist of arsenopyrite, pyrite, chalcopyrite, sphalerite, tetrahedrite, bournonite and rutile. Small amounts of pyrrhotite, gersdorffite, jamesonite, bornite, gudmundite, tetrahedrite, stibnite, kermesite, berthierite and native Sb are also present. Gold occurs as invisible and as 1 - 2 ¦m size inclusions in arsenopyrite and pyrite, on their grain boundaries and in fractures. The average amount of gold leached by cyanide is 2.93 per cent. The æinvisibleÆ gold contents were studied in pyrite and arsenopyrite by electron microprobe analysis (EPMA) and secondary ion mass spectrometry (SIMS) at CANMET/ MTL. Gold element distribution images show zoned patterns both in pyrite and arsenopyrite. SIMS analyses range from 343 to 55 ppm Au in arsenopyrite and from 217 ppm down to 0.32 ppm (detection limit 478 ppb) Au in pyrite. EPMA results range from 939 to below the detection limit 24 ppm Au in arsenopyrite and from 267 ppm to below 22 ppm Au in pyrite. Recovery of the refractory gold ore was studied using grinding, flotation, bio-oxidation and cyanidation tests. A sulfide bulk concentrate containing 40 ppm Au was obtained by flotation at 90 per cent recovery (As content 5.5 per cent, S content 22 per cent, and mass recovery 15 per cent). The grinding fineness in flotation was P80 -100 to 120 ¦m. At the original fineness the cyanidation recovery from the concentrate was lower than ten per cent, after ultra-fine grinding P80 -10 to 2 ¦m the Au recovery was less than 17 per cent. After bio- oxidation, Au recovery of 95 per cent was obtained in carbon-in-leach (CIL). The bio-oxidation time was two weeks in laboratory test, but after regrinding the oxidation rate was faster and recovery of Au higher. However, the selected method for the mining to be started in summer 2008 is open pit mining and mineral processing methods sulfide flotation and pressure oxidation in an autoclave. The ore reserves were estimated 31 December 2007 as: Probable 18.2 Mt with 5.1 g/t Au, Indicated 5.4 Mt with 3.0 g/t Au and Inferred 10.8 Mt with 3.4 g/t Au. The production capacity will be 3000 t/day.

Jan 1, 2008

By F Jiao, J Wang

By the year 2000, China was the sixth largest gold producer in the world, with about one-quarter of total production being derived from refractory or semi-refractory deposits. Although bacterial oxidation plants had been previously tried in China using local technology, these plants had not been commercially successful. The Laizhou Gold Enterprise (Tarzan BioGold Co Ltd) located in Shandong Province, undertook to modernise their gold processing facility in 2000 with the introduction of Bacterial Oxidation (BACOX) Technology. In 1997 BacTech Australia and Mintek of South Africa had formed a technology partnership, combining forces in the provision of bioleach technology. Under a cooperation agreement, BacTech/Mintek were chosen as the preferred technology providers for this first application of commercially proven bacterial oxidation technology within China. The paper describes the successful operation of this plant over the last three years. The events of project implementation are described, from the metallurgical testing of concentrate; through to the commissioning at the design throughput of 100 tonnes per day resulting in 80 000 ounces (2.5 tonnes) per year of refined gold. Process aspects of the operation encountered over the last three years are discussed which illustrate the robustness of the operation. The success of the bioleach facility has led to an advancement of plans to double plant capacity and some of the innovations, which may be employed in this expansion phase, are discussed.

Jan 1, 2004