Search Documents

THE South Mine. owned by the Broken Hill South Limited, occupies mineral leases 7 and 8 on the Broken Hill lode. The ore reserves are 4,250,000 tons, and the ore hauled for the year ended June, 1930, was 387,000 tons, the total to date being 7,840,000.The mine, down to the 1070-ft. level, is naturally divided into two sections, the northern and southern ends. Ore extraction is practically completed in the northern end to this horizon, while the southern end is developed ready for a concentrated attack.Fig. 1 shows the state of the 8215-ft. level, after connection to the new shaft.The levels above and below to the 1070-ft. level are in a similar condition, while below the 1070-ft. level the stoping has been confined to the north end, but not completed. The south end on these levels is also partially developed.The ore at present is hauled up No. 1 shaft, which is centrally situated to the present workings. This shaft was put into use in 1909, and in 20 years has had approximately 5,000,000 tons of ore pulled through it.The company, having proved the existence of large ore-bodies in the southern end of the mine, decided to sink No. 7 shaft. This is a six-compartment frame-set shaft (see Fig. 2) equipped with two cages and two 5-ton skips, the remaining compartments being utilised for electric cables, pipes, and ladders. The surface arrangements will include a steel head frame, electric winders, and breaker station.

Jan 1, 1930

By Noakes MJ, Willsteed TV

In the past few years an elevated gold price has resulted in the evaluation of many small scale surface gold deposits in Australia typically containing about 2-3 g/t Au. Operators have tended to assume that at the lower end of the grade spectrum only heap leaching is economically possible whereas above some assumed "cut-off" grade, carbon-in-pulp or similar techniques can be considered to have economic advantages.Studies made on a number of these prospects has indicated that this rather arbitary choice of treatment method can be mis-leading.A case study has been prepared assuming a "typical" situation and is presented. The deposit contains three million tonnes of ore assaying 3 g/t Au and is amenable to open pit mining methods. The mine site is remote but accessable and existing infrastructure is minimal. There are no unusual environmental constraints.

Jan 1, 1984

By Streichfuss M, KeBler H-W, Burgwinkel P

This paper describes the design of an expert system used as a part of a diagnostic system for diesel hydraulic drives. A PC-based diagnostic system ruDi (KeBler and Burgwinkel, 1993) was developed to minimise the time for diagnosis and repair work of vehicles with diesel hydraulic drives used in the mining industry. One part of ruDi is an expert system that helps to locate errors in any of a vehicle's subsystems, and supports technicians in removing the cause of a malfunction. Apart from the standard knowledge of diesel engines and hydraulic transmissions, the expert system supports the interpretation of the data obtained during sophisticated engine analysis tests such as high-resolution speed analysis or high-pressure analysis of the diesel injection system. The expert system is designed to diagnose various vehicles of the same type. Data for each vehicle is stored separately allowing checks to be carried out individually for each machine. An additional feature of this system is a database interface to a Maintenance Planning and Control System (MPCS) that allows an automatic generation of work orders for the defects found during the expert system sessions.

Jan 1, 1995

The epizonal Ag-Pb-Zn vein deposit at San Bartolome is characterised by a base-metal sulphide assemblage containing the spectacular development of interpenetrating, bladed networks of pyrrhotite which have been replaced by marcasite and pyrite. A similar assemblage displaying the same crystal habits and textures are also a diagnostic feature of the Sn and Sn- Ag deposits of Bolivia. On this basis, it is reasonable to conclude that both deposits were formed from fluids of similar nature and origin. Although no economic accumulation of Sn is known in San Bartolomr, further comparison of the geologic setting, age, mineralogy, fluid inclusion data and magmatic association of this deposit with the Bolivian systems has highlighted additional similarities consistent with a hypothesis that more extensive Sn mineralisation might exist in the San Bartolomd area.

Jan 1, 1995

Tin mining has taken place in the New England region of New South Wales since 1872. Until fairly recent times there was little pro- vision made for environmental protection. Mining methods,which included ground sluicing and open cutting,had considerable environmental impact. Much of the topsoil was lost and there is little vegetation on the infertile and at times toxic, subsoil. Thus much of the lands disturbed by mining have not been stabilised and are eroding, causing extensive pollution of adjacent watercourses. There are more than 1500ha of abandoned tin mine sites in the New England, representing one of the worst rehabilitation problems in New South Wales and reflecting poorly on the mining industry as a whole. Recent tin mining operations incorporate progressive rehabilitation in their mining cycle. Topsoil is stockpiled and later respread. This topsoil contains a seed source, facilitating revegetation and thus stabilisation. The tin mining industry, under considerable cost pressures at present, is seeking a cost- effective revegetation technique. Most of the mines in the New England are situated in a forest environment. Trials have been conducted in the past using exotic pasture species with limited success due to the characteristics of the subsoil. Other revege- tation trials have used pine or eucalypt tree species. The cost of these techniques is a major disadvantage. Certain acacias species were observed colonising disturbed tin mining areas on very infertile subsoils. Acacias have a number of characteristics indicating a possible applic- ations in mine rehabilitation programmes.

Jan 1, 1987

By Simmons SF, Fleming J

Alteration and mineralisation at the Island Copper deposit is related to the intrusion of Early Jurassic quartz feldspar porphyry dykes into surrounding comagmatic Bonanza volcanic rocks. The pyrophyllite alteration zone forms an upward flaring cone, largely hosted within a breccia body that c ross-cuts the Cu, Mo, and Au-rich ore shell. This alteration zone contains pyrophyllite, dumortierite and diaspore and resembles alteration occurring in some high-sulfidation deposits, but which is barren. Fluid mineral equilibria and fluid inclusion studies indicate formation at approximately 300 ¦C from fluids dominated by steam and gases. These fluids appear highly acidic, but sulfur poor, leading to extreme base leaching within the breccia body and surrounding rocks.

Jan 1, 1995

By Parker RJ, Swindells CF

The authors have used the geotechnical study for design of the South Wall of Mt. Newman Mining's Mt. Whaleback Mine to illustrate how geotechnical studies can be economically justified. This is achieved by relating the savings resulting from increased ore recovery and prevention of failure to the cost of the study. An outline of the geotechnical study is provided in the paper, including a brief description of the innovative methods used to investigate geological structure of the mine and descriptions of the methods of slope reinforcement adopted.

Jan 1, 1986

By Eggins SM, Crawford AJ, Maillet P

The Fiji Islands are remnants of a once continuous Solomon-Vanuatu-Fiji-Tonga volcanic arc (the Vitiaz arc), located at the boundary between the Indian-Australian and Pacific plates. They record a history of (i) arc volcanism the late Eocene to late Miocene, (ii) an extensive magmatic response to arc rifting (5.5-3.OMa) during which volcanism was dominated by shoshonitic to tholeiitic basalts, and as rifting continued, (iii) a transition from arc to intraplate volcanism. The Hunter Ridge-Hunter Fracture Zone separates the inactive South Fiji Basin from the actively spreading North Fiji Basin, and has been considered to be a transform zone, almost parallel to the motion vector of the Australian plate. However rocks dredged during the 1993 `Alize' cruise, from along the northern part of the Hunter Ridge are typical arc tholeiites, and therefore demand that subduction has occurred beneath the Hunter Ridge sometime during the last û 5Ma.

Jan 1, 1995

A non-contacting under-belt capacitance and gamma-ray backscatter technique has been developed for the on-line measurement of moisture in coal. In this technique, moisture was correlated with radio frequency susceptance and conductance determined using an under-belt capacitance sensor in which a fringing electric field Interrogates a layer of coal on the conveyor belt directly above the sensor. To compensate for variations in the density and thickness of the coal layer, an under-belt gamma-ray backscatter gauge was used to measure an equivalent volume of coal.A plant trial of the technique was conducted at Stockton Borehole Colliery, SW Australia, where the gauges were installed on the coking coal product conveyor. Product moistures, in the range 7 - 14%, were determined with r.m.s errors of 0.50 and 0.25 wt% using on-belt and static off-belt gauges, respectively. The difference in the on-belt and off-belt gauge measurement accuracy was attributed to sampling errors in the calibration of the onbelt gauge.

Jan 1, 1989

Integrated geological interpretation of aerial photographs and Landsat images revealed that the gold mineralisation at Kyauk Pahto took place in a narrow zone of tension fractures within part of a previously unrecognised dextral wrench fault system. The latter is the wider manifestation of the well known Sagaing (right-lateral) strike-slip fault which has a length of more than 1 000 km, and it demarcates the boundary between the Indo-Australian and Asian plates. A subtle, right-handed kink affects the full width of the Sagaing Wrench-fault System at about the latitude of Kyauk pahto, and the extra dilatancy imposed on the tension fracture zone facilitated episodic ingress of mineralising hydrothermal fluids by "seismic pumping".

Jan 1, 1987

Reconnaissance geochemical exploration in the vicinity of low angle detachment faults which bound the core of the Paparoa metamorphic core complex yielded Au up to 14 ppm, with 35% of greywacke, granitoid and quartz vein samples in the northern range exceeding the 0.01 ppm detection limit. Au is associated with Ag, As, Sb and Cu anomalies consistent with epithermal-type mineralisation. The Ag and Cu anomalies also distinguish this mineralisation from older, mesothermal Au deposits widespread in the Ordovician 'slate belt' greywackes, which comprise much of the upper plate of the core complex. Baryte, molybdenite, fluorite and stratiform U mineralisation in the northern Paparoa Range may also be related to hydrothermal activity along the detachment fault zones.

Jan 1, 1995

By G Munro

he Melbourne City Link project will complete a missing link between two existing major freeways in the Melbourne road network, providing a much needed bypass of the Central Business District for through traffic. The project, which is being financed under a BOOT arrangement with the Victorian State Government, involves the upgrading of significant stretches of existing freeway and the construction of new sections involving viaducts and tunnels. The tunnel sections, which are the focus of this paper, are beneath residential and business areas, the Yarra River, the Royal Botanic Gardens and significant sporting facilities where surface construction would be either impossible or unacceptable (reference Figure 1). The shorter, 1.62 km west bound Domain tunnel comprises two cut and cover sections through Olympic Park then the Yarra River, the driven section of 0.68 km length and exits through a common cut and cover section with the east bound tunnel under St Kilda Road and Sturt Street. The longer 3.76 km east bound tunnel commences at the common portal, through cut and cover under St Kilda Road then 2.86 km of driven section before exiting at a cut and cover section at Burnley. The longer Burnley tunnel has an access and ventilation shaft at approximately its mid point.

Jan 1, 1999

By S G. Gatehouse

Extensive gold mining activity û dominantly alluvial û has taken place in the Sofala-Wattle Flat district since the 1850s.This work will have located most, if not all, of the visible sources for the gold in current stream systems.Also, there are many gold bearing elevated Tertiary alluvial terraces in the district which may confuse possible gold signals from primary hard rock sources in the streams.Associated element signatures eg As and other chalcophiles, will discriminate non-alluvial signatures but will not necessarily distinguish non gold bearing mineralisation.Both trace elements and conventional gold analyses will dominantly re-identify known occurrences. Conventional BCL sampling is considered misleading as experience from the Oberon area to the south of Sofala demonstrated that BCL sampling was very sensitive û perhaps too sensitive.All occurrences û major or minor û of gold will be detected (Gatehouse, 1992). To improve on BCL sampling, a small, -120# sample with selective duplication was recommended to screen coarse-grained gold anomalism and a program of sampling covering an area thought to be prospective was enacted.Samples returning anomalous Au were analysed in duplicate and if the results demonstrated reproducibility, indicating fine gold only, the sample site was assigned a high priority.It was found that most of the reproducible samples clustered in one area û Spring Gully. The results of this sampling program led to immediate identification and, ultimately, the successful delineation of the Spring Gully gold deposit near Wattle Flat.

Jan 1, 2004

By Blom MS

Two well-developed styles of mineralization occur in the Nevados del Famatina mining district, Famatina ranges, La Rioja province, Argentina. Porphyry molybdenum- copper-gold mineralization and high level acid sulphate alteration/mineralization (Nevados del Famatina) are related to intrusion of the Pliocene Mogote rhyodacite porphyry complex. High sulphidation epithermal mineralization (La Mejicana) is developed peripheral to the Nevados del Famatina deposit. Both are hosted mainly by the Ordovician Negro Peinado metapelites.At Nevados del Famatina, five mineralized fracture events have been identified and correlated with four distinct alteration assemblages. Stage I (barren quartz) and stage II (molybdenite¦sphalerite¦pyrite) mineralization are associated with a K-silicate alteration assemblage of K-feldspar+biotite+quartz+magneti te¦ilmenite¦anhydrite. Stage III (bornite+pyrite+sphalerite+molybdenite ¦chalcopyrite¦idaite) and stage IV (chalcopyrite+pyrite +sphalerite+gold¦tennantite-tetrahedrite) mineralization are related to a quartz-sericite assemblage of quartz +phengite+illite+pyrite+rutile. Stage V mineralization is divided into two substages. Stage Va (chalcopyrite +pyrite+sphalerite¦ tennantite-tetrahedrite ¦ tellurides ¦ gold ¦enargite¦famatinite¦stibnite¦molybdenite) is related to a sericite-clay assemblage of quartz+illite+kaolinite ¦montmorillonite¦alunite. Alunite-kaolinite alteration (alunite+pyrophyllite+kaolinite+ aluminum - phosphate -sulphate minerals ¦illite¦fluorite¦corundum¦anhydrite) occurs in the upper part of Nevados del Famatina associated with the later stage Vb (quartz+famatinite +chalcopyrite+covellite + chalcocite ¦ marcasite ¦ enargite ¦ luzonite¦sphalerite¦melnikovite) mineralization.

Jan 1, 1990

Most of the copper deposits in the Lachlan Geosyncline fall within areas having either a common host rock, mineral assemblage, form of ore body or time and method of emplace- ment. On this basis a Cobar-type ore has been recognised in the deposits of the Cobar -- Mt. Hope - Melrose region. The copper ores in the Tottenham-Girilambone area to the east have a different mineral assemblage. In the more rugged Central Highlands nearer the coast copper deposits are generally concentrated either in one of several Ordovician andesite belts, particularly between Wellington and Woodstock, or within Silurian acid volcanics developed in irregular fashion over a considerable portion of this region. In only a few instances is copper known in the granite batholiths which adjoin these volcanic belts. Native copper and magnetite are characteristic of the deposits of the andesite province and it is possible that future mineragraphic studies will indicate significant differences in the base metal sulphides of both the andesitic and the more acid volcanic belts. Ores having similar mineralogy and form to the Captain's Flat deposit are known at various localities in the eastern segment of the latter belt. In the Gundagai area several small copper deposits with associated nickel minerals have been developed in the Coolac Serpentinite belt.

Jan 1, 1969

By Thornber MR, Davidson LR

The cause of spontaneous combustion of pyritic black shale has been studied by calorimetry and other techniques. The conditions required for ignition to occur are: 1. A critical mass of pyritic black shale. 2. Acidity. 3. Fine shale particle size. 4. A high ambient temperature. 5. The exclusion of air during the preparation of a calorimeter charge. The reaction is characterised by an initial incubation period during which an unknown phase is produced. The build up and oxidation of this phase results in a chain reaction culminating in ignition. The mechanism is believed to involve the interaction of pyrite, sulphuric acid, ferrous sulphate, or meta-stable oxysulphates, with ammonium nitrate. The recommended strategy for prevention of premature detonation is to neutralise the acids in the shale with quick and slow release alkaline materials.

Jan 1, 1986

By McQuade CV, Riley SJ

Acid mine drainage is an unavoidable consequence of some coal mining operations. Typically runoff pH is below 3.5 and at these pH levels heavy metals are mobilised. Leachate from coal reject dumps may require collection and treatment to raise the pH and precipitate the metals before being discharged.A bi-product of coal mining operations at Clarence Colliery is coarse washery reject. At present the coarse reject is deposited above ground and rehabilitated. Adjacent to Clarence Colliery is the Kable's Transport Pty Ltd sand mining operation. It has been proposed that co-disposal of the rejects from both operations may produce a product whose leachate has near neutral pH.

Jan 1, 1998

By Tilley J. L, Chicu D

The development of the Yallourn East Field brown coal open cut has involved the adoption of novel investigational programs into coal qual- ity. For example, weighted average coal property statistics for key proper- ties are determined by using a unique blend of traditional and 3-dimensional geostatistical estimation. Predicted property values are made freely available from the mainframe computer in the form of kriged esti- mates of 60 000 tonne coal blocks. Geostatistical predictions are being incorporated within the Mincom/Intergraph CADD system which is used for mine design. Key properties relating to coal type, moisture, and ash have been evalu- ated to provide the required data for the design and operation of both the open cut and the power stations as well as the briquette plant.

Jan 1, 1989

By B Walker, A Robertson, C Wels, S Fortin

A background characterisation study was carried out in the Sangre de Cristo mountains, New Mexico, to: quantify naturally occurring contaminant loads from mineralised areas; define site-specific background concentrations; and to determine key factors controlling spatial and temporal variations in contaminant concentrations. The study included a comprehensive sampling and testing program (paste pH/EC, ABA, leach extraction tests) of soil/bedrock from mineralised areas (including erosional scars), and a ground water and surface water quality monitoring program in selected mineralised watersheds. Results demonstrate that high concentrations of contaminants occur naturally in ground and surface water draining the mineralised area of the Red River basin. The erosional scars were found to represent the major source of acid rock drainage (ARD) (~66 per cent) in this area due to: high rates of weathering and erosion, which continually exposes sulfide-bearing outcrops; and high rates of run-off as a result of high elevation and lack of vegetation. The scar material is generally very acidic (paste pH ranges from 8.5 to 1.5; average = 3.6) with highly elevated concentrations of sulfate and leachable metals. The composition and concentration of leachable metals vary significantly, not only between scars but also within a given scar. While all streams draining the various scar watersheds are highly acidic, each has a characteristic æfingerprintÆ of sulfate and metal concentrations. Most of the run-off from the scars infiltrates into alluvial debris flow aprons and reaches the Red River via groundwater flow.

Jan 1, 2003

Exploring for deep shallow dipping orebodies can be very expensive and very difficult. Surface exploration is often not an option and obtaining the best location for underground drilling can cause production delays if drilling is carried out from development headings. The Otter/Juan mine has been in production for approximately 34 years. All of the production is now sourced from more than 1000 metres below the surface from an area known as the Edwards Lode. The orebody is shallow dipping and open at depth. Exploration drilling has been performed from decline stockpiles and from hangingwall drill drives. Drilling from footwall positions (eg decline stockpiles) into shallow dipping orebodies can often produce intersections which are unusually thick thus leading to optimistic resource figures. The decision to develop a dedicated hangingwall drilling position can vastly improve the quality of the data used to generate an orebody model. In 1997 a new extension to the Edwards Lode was discovered and named the æFÆ surface. In 1999 a resource calculation was performed using data obtained from drilling that was carried out from decline stockpiles. In 2002 a dedicated drill drive was developed into the hangingwall of the æFÆ surface to obtain better data to verify the previous resource calculation. For this case study obtaining more representative data reduced the resource estimate by 66 per cent. This information was obtained early enough to allow for alteration to the mine plan and without loss of capital.

Jan 1, 2003