Search Documents

By P Allum

This paper presents a case study to reduce the operational cost on the secondary ball mill circuit in the Lead/Zinc Concentrator at Mount Isa Mines. The circuit includes two five-metre diameter ball mills each closed with a cluster of ten 15-inch cyclones. The operating cost for both ball mills is about six million Australian dollars per annum.The concentrator achieves 75 per cent of the plant design capacity with one ball mill operating, but will have to use two ball mills when 100 per cent plant capacity is required. The optimisation study on the circuit identified a new flowsheet that enabled the concentrator to reach 100 per cent of the capacity by using one of the two secondary ball mills. The success of the project utilised the existing equipment rationally and saved the operational cost for one ball mill at full concentrator capacity. A further simplified secondary circuit is proposed using the IsaMill for the secondary grinding duty. Performance of the IsaMill circuit and the potential cost savings are predicted.

Jan 1, 2002

By U Briem, R Verreet

The level of wire rope technology used in mine hoisting applications has a significant effect on the overall efficiency of the hoisting system. This paper discusses the effect that a reduction in rope mass per unit length and an increase in rope breaking strength can have on rock skip capacity and hence mine shaft output. A 20 per cent reduction in rope mass per metre for a typical 48 mm hoisting rope, while maintaining the breaking strength, increases the skipÆs capacity by circa 30 per cent at a suspended rope length of 3000 m. Such gains in shaft output, without any significant changes to the shaft or winder design, can have major implications for the feasibility of future deep mine projects. The technical challenge for rope manufacturers is how to get rid of 20 to 30 per cent of the rope mass while keeping the breaking strength and modulus of elasticity of the whole rope constant. CASAR are currently developing steel wire rope constructions where the steel IWRC has been replaced with high strength, high modulus fibres such as Kevlar«, Spectra« and Dyneema«. One of the key aspects of such composite rope designs is to ensure equal load sharing between the different rope components, ie in proportion to their area. If there is a significant difference in modulus between the fibre core and the steel outer strands, the core may not carry its proper proportion of the load and the outer strands would be overloaded. Some technical aspects of the design of composite steel wire ropes are discussed. A design and operational issue that needs careful consideration is the safe non destructive testing (NDT) of composite ropes. Traditional magnetic NDT would only be capable of inspecting the steel wires. Techniques therefore need to be developed that would give operators a reliable indication of the condition of the load bearing fibre core. This paper also discusses possible solutions to this very important NDT question.

Jan 1, 2005

By Misk A

Several logging methods are presently available to the oil industry for the evaluation of formation porosity: the Sonic and Neutron logs are already widely used, the Gamma-Ganmia log is being progressively introduced. The readings of these instruments are primarily a function of the rack-porosity, hence the general term of "porosity tools". Apart from porosity, however, other variables such as type of fluid in the pores, nature of matrix and degree of shaliness have an important influence.The response of each device is a different function of such parameters: therefore, a cci bination of porosity tools can lead to information on these variables in addition to the evaluation of effective porosity.For example, the presence of gas; rather than water or oil, in a formation which is not deeply invaded, will tend to give Neutron derived porosity values which are too 'low; on the other hand, the Sonic derived porosity: value will be too high in such- a case. For the same porosity, the Sonic gives a longer transit time in sandstone than limestone, whereas in the low porosity range, the Neutron will read more counts per second in a sandstone than in a limestone of the same porosity. The presence of shale also affects the readings of the various porosity tools in different ways so that the combination of two or more methods may lead, in some cases; to an evaluation of both the-effective porosity and the shale, content.In conclusion, it may be said that the various porosity tools pre-sently available, are, to a large extent, complementary, and that in many problems the use of two porosity tools, instead of one, is very likely to bring valuable additional information.

Jan 1, 1962

BHP Minerals Ltd operates an open cut iron ore mining operation on Koolan Island, off the coast north of Derby in the Kimberley region of Western Australia. The mine comprises a number of pits, the largest of which is situated adjacent to the coast on the southern side of the island. The lowest bench is currently at RL +2 m, and the mine has planned ultimate depth of RL -82 m. Mining has already extended below the pre-existing water table level, and below mean sea level. In 1984, an extensive program of drilling, geophysics and test pumping was instigated to evaluate the aquifer hydraulic properties and the nature of the groundwater flow regime. With the aid of computer modelling, predictions have been made of the likely dewatering and depressurization requirements, and a conceptual pumping and drainage system has been designed.

Jan 1, 1986

By D Langberg, R Taylor

Many metallurgical operations produce fine residues and dusts as by-products which can be difficult to handle and offer little direct financial incentive to treat. There is a growing imperative to deal with these materials particularly since land fill is fast becoming an uncertain long term solution. One possible means of treatment is to extract the valuable metals while fusing the remainder into a slag. In this way valuable metal components of the material can be recovered and the less valuable components be converted into useful products, eg cements and inorganic polymers which have a high environmental stability and a growing market. The aim of this project is to establish solids injection and fusion in a slag bath as a viable method of treating industrial wastes and residues. The benefits of this approach are expected to be: the ability to treat a wide range of organic and inorganic residue materials, ease of recovery of volatile and valuable elements and the production of final materials which could be used in other industries. In ongoing experimental work at the CSIRO Minerals a 250 kg slag bath reactor has been used to test the injection of Paragoethite residue into an iron silicate based slag. An experimental apparatus has been designed and commissioned to pneumatically inject solid material at feed rates of up to 80 kg/hour. The capture efficiency of injected solids by the slag bath was calculated by monitoring the composition of the slag. Using this method of treatment, the zinc contained in the residue can be recovered as a fume by varying the oxidation state of the slag. Other valuable elements could be recovered by creating a matte or metal phase in the reactor with the final material being used in the production of cement. A capture efficiency of injected solid paragoethite particles in the slag bath of up to 97 per cent was achieved. Under the conditions of the experimental work capture efficiency was found to be independent of injection velocity and slag depth. The rate of fuming during injection was found to increase slightly with injection velocity and was independent of slag depth.

Jan 1, 2002

By Moorrees C

Carbonic acid leaching of crude iron-containing magnesia derived from Savage River magnesite yields a magnesium bicarbonate leachate with a substantial soluble iron concentration. The iron concentration depends upon the leaching conditions (particularly time, temperature and pulp density) but is generally in the range 0.005-0.5 g/litre. If this soluble iron is not removed prior to the precipitation of the magnesium as a hydrated carbonate, then this product will be contaminated by the iron, and will not yield a final product (high-purity magnesia) that meets specifications.The soluble iron content of the magnesium bicarbonate leachate can be reduced to an acceptable level by addition of solid aluminium sulphate either during carbonic acid, leaching of the crude calcine or to the clarified leachate. Chemical analysis and X-ray diffraction revealed that the iron is precipitated as an iron-containing hydrotalcite-type compound, [Mg6(Al,Fe)2(OH)16]CO3.4H2O. The actual composition of the precipitate depends on the amount of aluminium sulphate added and the precipitation technique used. Because precipitation of iron in this manner also results in reduced magnesium recovery from the leachates, It WIll be necessary to develop methods for recovering the magnesium component of the precipitates.

Jan 1, 1984

By Hughes A

Nchanga Division of ZCCM has installed and operated a trolley assist system on part of their truck fleet for some three years. This paper examines how the system came to be chosen and how the many features of construction and operation were dealt with. The economics and productivity of the system are presented as are the personnel aspects of acceptance and training. Zambia Consolidated Copper Mines is a state controlled copper mining company formed by the amalgamation of the former Nchanga Consolidated Copper Mines and Roan Copper Mines. The company operates seven copper mines the largest producer being the Nchanga division, which is scheduled to produce some forty-two percent of Zambia's copper production. The division operates four open pits and an underground mine which produce annually some 192 000 and 96 000 tonnes respectively of copper contained in ore.

Jan 1, 1986

By P Cundall

Three-dimensional DEM (Distinct Element Method) simulations were conducted in order to examine the performance of screw conveyors, which are installed to transport bulk materials as parts of many industrial machines, including mining and construction machinery. To apply the DEM to the analysis of screw conveyors, we added a spiral object and cylinder objects, which correspond to the helical screw, the casing pipe, and the driving shaft of a screw conveyor. These objects are represented analytically to enhance the precision and efficiency when calculating the interaction between objects and particles. Simulations were conducted for some real applications: inclined and other types of screws, as well as the basic types (horizontal and vertical). Results were compared with previous work and empirical equations. It is concluded that this method is sufficiently well-developed and useful to analyse various kinds of screw conveyors.

Jan 1, 2000

In early 1985, Bougainville Copper Limited commissioned an automatic truck despatch system to control its fleet of 44 trucks and 9 shovels. Productivity gains in the past have been the result of increasing equipment size then improving availabilities. The emphasis now is on improving the use of that availability and in particular for trucks, in reducing non-productive truck movement. A batch allocation computer based truck control system had been in operation since 1978, so to achieve the desired improvements it was necessary to move to an automatic dynamic control system. A description of the system installed is given, together with a review of how the project was engineered, the problems encountered and the results achieved to Date.

Jan 1, 1986

Iron ore in the Pilbara Region of Western Australia varies in composition giving iron ore a range of densities. An accurate density figure of the material leads to accurate calculations of production throughput. Density studies of two separate iron ore mines were conducted in the Pilbara. Procedures and results are reported here.The Pilbara Region of Western Australia has a number of iron ore operations. Two mines have conducted density studies of their materials. The purpose for the studies was to determine an accurate in situ bulk density that could be applied to volume and tonnage calculations of the operation. It was identified that density was one culprit causing calculation variations. Density is an important figure used to estimate ore reserves, equipment requirements, production rates and indirectly costs and sales revenue. One study was conducted at Rio TintoÆs Robe River Mine based near the town of Pannawonica. Its Mesa J orebody is currently being mined and is a low-grade deposit of goethite and hematite (Burnham, 2003). A separate study was conducted at BHP BillitonÆs Yarrie Mine situated north of Newman and east of Pardoo. Its orebody consists of high grade formed by a supergene enrichment of cherty material and a burial metamorphism to produce hematite (Richardson, 2002). The method used to determine density was by large-scale samples using the pre-mining in situ volume of the material and the weight in tonnes after mining.

Jan 1, 2003

By A Califice, E Pirard, M Benzaazoua, R Mermillod-Blondin

Image analysis is more and more considered as a powerful tool for quantitative analysis of ores and concentrates. Apart from being very much dependent upon the quality of the imaging principle and the adequacy of the imaging sensor, quantitative image analysis is also the result of a long chain of material, image and pixel sampling strategies. The most reliable way to demonstrate the accuracy and the precision of modal analysis obtained from images is probably to use a blended material with known proportions of pure minerals and confront the results obtained from different analytical tools. This operation has been performed on a series of mineral blends mimicking the tailings of a flotation operation in a plant operating on massive sulfide mineralisation. The intention was to be able to better predict acid mine drainage potential from direct mineralogical observations. Selected sulfide minerals: pyrite (Py), pyrrhotite (Po), chalcopyrite (Cp) and sphalerite (Sp) were mixed as variable amounts within gangue minerals (quartz, calcite, dolomite and siderite). Typical blends contained six to ten per cent (Py); one to three per cent (Po); 0.5 to one per cent (Cp, Sp); 15 to 40 per cent carbonates and 40 to 75 per cent quartz by mass. The 1000 gram blends were carefully sampled and prepared for X-ray diffraction, chemical analysis by ICP-AES and optical microscopy image analysis (OMIA). Results obtained for the different analytical techniques are compared and discussed revealing the limits and strength of each method in the accurate quantification of sulfide and gangue minerals.

Jan 1, 2008

By Harris RW

Acoustic Emission structural integrity evaluation tests rely on the validity of the detected acoustic emission data and the ability of the practitioner to both analyse and interpret the data to make a correct decision on the future use of the structure tested. Unfortunately with acoustic emission surveillance testing, it is not possible to know that all the available data has been assessed property. The equipment sensitivity, threshold settings, and event capture capacity, when combined with the decision making ability of the operator in real time, make it very difficult to achieve reliable integrity evaluation. The main problem is to interpret the data and so any monitoring system should involve expert systems in conjunction with both acoustic emission and other operational monitoring data to maximise the utilisation of the large amounts of information now available from operating plants, mines and structures.

Jan 1, 1991

By R Gaze, J Horton

Block models generated with all linear interpolation algorithms contain inherent smoothing that typically results in an underestimation of grades and overestimation of tonnes in resource estimates. For mineral deposits that are anticipated to be exploited by underground mining methods excessive smoothing may result in materially misleading estimates of Ore Reserves. To account for smoothing in the open pit mining environment recoverable reserve techniques such as indicator kriging and uniform conditioning are employed to provide non-spatially located proportions of the large blocks above the cut-off grade. These models are not suitable for underground mine planning where the actual location of material above cut-off is required to design its extraction. To correct for excessive smoothing it is proposed to modify the ordinary kriged block estimates a posteriori using an affine correction with a local variance adjustment factor. The proposed methodology is demonstrated for a base metal deposit during a feasibility study.

Jan 1, 2009

This paper carries on from an earlier paper 'Cemented fill practice and research at Mount Isa' and reports further on the laboratory programme at Mount Isa to develop a cheap cem- ented fill using Company waste products. The practical economic significance of availability of cheap cementing agents is re- viewed, with the various alternative approaches available The basic approach adopted within this paper is that use of reactive pozzolans such as ground slags to replace a proportion of the Portland cement in the fill can make mining methods employing cemented fill more economic- ally competitive with other mining methods.

Jan 1, 1973

Arising from prospecting success, the underlying worth of the shares of a publicly listed mining exploration company can increase many-fold. Prompt and accurate reporting during the exploration stage is therefore essential. While there is scope for varying degrees of optimism or caution in statements about the future economic prospectivity of a mineral deposit which has been discovered, the directors of a mining exploration company have both a legal and ethical obligation to keep their shareholders and the general public fully informed as to the state of progress of, and significant factual results arising from its exploration efforts. Suggestions are made as to the desirable form and content of exploration reports up to and including the time when the orebody has been delineated in terms of assured tonnage and grade. The benefits which will flow from this greater disclosure are discussed.

Jan 1, 1979

By Hoskings AD

Bolting forms a prestressed elastic layer of rock which is capable of supporting loads at right angles to the bolted surface. Investigations on rock bolting made with a number of different models give rise to empirical and theoretical prin- ciples for the formation and action of the layer. In the models, flat and arched layers of many materials were used simulating rock conditions ranging from closely interlocked blocks to fragments of various shapes. Results of observations made in the underground works of the Snowy Mountains Scheme are related to the mode of action of bolted surface layers of rock. There is abundant experimental, theoretical and practical explanation for the well-demonstrated capability of bolting as a means of rock support.

Jan 1, 1971

By A McCarthy

Spatial modelling has been used to determine potential locations of granite-related nickel skarn mineralisation throughout eastern Australia. It is believed that during granite intrusion, fluid can leach nickel from nearby mafic lithologies and combine with sulfur to form nickel sulfides. Currently exploration for this style of deposit has been limited to the region around the Avebury Deposit in western Tasmania. As the lithologies near Avebury are not unique it is feasible that similar deposits could exist elsewhere in Australia. The weights of evidence spatial data modelling technique was used to evaluate the wealth of geological data available over eastern Australia and included known economic deposits as training data to weight the themes of the model. These weighted themes were combined to create a prospectivity map showing areas favourable for granite-related nickel deposits. Several regions were identified by the model to have good potential to host nickel mineralisation similar to the Avebury deposit. These include areas located throughout New South Wales, Victoria, Tasmania, the Tasman District of New Zealand and, in particular, the Rockhampton region of eastern Queensland. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

The introduction of legal certification of mine managers is a matter of history. It was introduced as part of legislation for mine safety. It has been said that such legislat- ion was written in blood. Like all legislation this legislation is divided into three sections; commands, obligations and sanctions. While legislation in all States on this subject is similar, the differences are great enough to have prompted the preparation of a Uniform Code by the Annual Conference of Chief Inspectors of Mines. This Uniform Code has not been adopted fully by any State to date. Legal certification of mine managers has made managers more aware of the requirements of the legislation covering their industry, legislation that reads as a summary on past accidents and methods of preventing them. While budding managers spend considerable' time in their early years in the preparation for certification, history has shown that the industry has benefited from their efforts. A better knowledge of the safety acts by the managers has produced safer operations, and a higher standard of management has raised the technical standards of mining operations to a stage where Australia can be proud.

Jan 1, 1980

By Erceg MM

The Red Dome deposit is located about 15 kilometres by road west of Chillagoe in far north Queensland. The deposit is within a well known band of mineralisation which is adjacent to the Chillagoe - Mungana railway line. Earlier this century several mines were operating in this area, some of which were supplying feed-stock to the copper smelters which were operating in Chillagoe at that time.The area around Chillagoe has long been an interesting geological region with numerous locations exhibiting significant gold and base metal mineralisation.The Red Dome area of some time, however it was not became involved that the apparent. The upsurge in seventies added further investment.mineralisation had been known for until Noel Adam, a prospector,true potential of the area became the gold price in the late encouragement for additional

Jan 1, 1986

It is difficult with inadvertent explosions to establish fundamental data, especially of original dust, of pressure, temperature etc. and of ventilation oscillations, as exposed personnel rarely survive. Retrospective data from explosions must be derived from damage, from fatalities, from ventilation analyses, from analyses of dusts and other indications of temp- erature and duration of temperature. The five disastrous explosions selected for analysis provide examples of what data can be established as to the cause and extent of explosions. Such information is required for legal etc., inquiries subsequent to explosions, but most importantly to give the best guidance for avoidance of possibility of further Disasters.

Jan 1, 1981