Search Documents

By Lockyer PC, Reed MR Bartlett PM

Difficult ground conditions have plagued the underground operations at Mount Windarra since mining started in 1974.The ore at Mount Windarra consists of seven vertically dipping, sub vertically plunging ore shoots. The ore zone in which the shoots lie is characterised by moderate to heavy cleavage and the presence of serpentanite. The ore is known to extend to 1100 metres below surface.Long hole open stoping under cover of backfill has been used as the primary mining method at the mine, but its poor performance brought the mine near to closure in 1984. The mine had been closed from 1979 to 1980.

Jan 1, 1985

Mount Isa mine is the largest underground mine in Australia and is located 2,000 kilometres north-west of Brisbane. This mine has been in continuous operation since 1931 and in 1986/87 the silver/lead/zinc stream achieved the peak annual mining rate of 4.7 million tonnes. At present about fifteen different steeply dipping stratiform orebodies are being mined to maintain an annual production rate of around 3.0 million tonnes. Out of these, only two orebodies (2 & 5) are amenable to sub level open stoping (SLOS) type bulk mining methods. This year only 150,000 tonnes are scheduled from pillars and remnant areas but in future, more sources will be required to meet the budget production targets.

Jan 1, 1990

By Eaton R. A

The design of most underground mining machines shows little evidence of regard for ergonomic principles and operator comfort. Likewise, efficiency and ease of operation often appear to have been given little consideration in machines where ruggedness and simplicity have tended to dictate the configuration. Improvements in productivity are amongst the benefits to be gained by a different approach to machine design. The paper describes the philosophy and features of a test bed Load-Haul-Dump Vehicle undergoing trials at Mount Isa Mines. This machine is the outcome of a Research and Development Programme conducted by the Department of Mechanical Engineering at the University of Queensland and Mount Isa Mines Limited. The diesel powered test bed features an enclosed, air conditioned cabin, with a suspended operator's control station and electrically operated controls. An electronically controlled hydrostatic transmission incorporating wheel slip control, is another innovation. The performance and operator acceptance of the machine has led to adoption of most of the concepts in a new machine now being put into production.

Jan 1, 1987

By Hall ST, Miles NJ

Recently an inorganic salt, sodium polytungstate (SPT), has become available that allows the preparation of non-toxic solutions of relative densities up to 3.1. It is relatively expensive and at the higher relative densities achievable, highly viscous. Alternative inorganic compounds may in the future be identified that overcome these limitations. The Australian Mineral Industries Research Association Ltd (AMIRA) has initiated a project to examine possible alternatives. However, it has been found that by the addition of finely divided ferrosilicon to solutions of SPT, relative densities of up to 4.0 can be achieved. A laboratory technique for density fractionation of sized mineral samples utilising this finding has been developed. This is currently being extended to study the potential applications of such liquids and suspensions in dynamic systems for mineral, coal and recycled waste separations.

Jan 1, 1993

By Waters A. G, Nightingale R. J

The quartzite added at the blast furnace for the purpose of adjusting the chemistry of the burden inputs is shown to have a disproportionate impact on both the level and the variability of the hot metal silicon (HMSi). This conclusion is supported not only by direct correlation involving data from five blast furnaces, but also by mass balances. In one case the R2 correlation coefficient was 0.96 and the mass balance was accurate to within five per cent for a wide range of quartzite additions. The results indicate that as much as 43 per cent of the silicon in the added quartzite reports directly to the hot metal. Indeed, silicon from quartzite was found to be much more likely to report to the hot metal compared to silicon from regular sources (eg coke and sinter), reflecting differences in the activity of the silicon source.

Jan 1, 1994

By Howard G. L

The gold treatment plant of Great Western Consolidated N.L. is at Bullfinch, Western Australia, 22 miles north of Southern Cross, which is 100 miles west of Kalgoorlie. A railway to Southern Cross connects the mine with the main Perth-Kalgoorlie line.The plant, which commenced operations on the 31st October, 1952, was, designed by Messrs. Alex: Stewart & Co. in consultation with the technical staff of Western Mining Corporation Ltd. to treat 1,000 long tons a day, made up of approximately equal parts of quarry oxidized ore and underground sulphide ore, by moderately coarse grinding (2-3 per cent plus 65 mesh Tyler) and straight cyanidation without straking. The design had to allow for future treatment of all sulphide ore at the rate of 40,000 tons per 28-day periodand to make provision for the possible later inclusion of preaeration treatment.The test work on .which design was based was done on representative development samples, the mine being divided into zones for this purpose, to check possible local variations from average treatment behaviour. Proposed mill feed mixtures were made up from time to time for complete ore dressing tests, which were conducted in the Western Mining Corporation laboratory at Kalgoorlie.The chief feature of the design was that the plant had to handle the extremes of very soft, poor settling and filtering oxidized ore and very hard, good settling and filtering sulphide ore. On one hand, crushers and mills had to be large enough to handle the sulphide ore and on the other, thickeners and filters had to be large enough to handle the oxidized ores.The design is marked by simplicity, the use of large units of equipment, and flexibility to cope with a variety of ores.

Jan 1, 1956

By Henderson J, Ward RG

Dissolved oxygen has been measured directly using a rugged, reliable, accurate electrochemical probe system developed for steelworks application by B.H.P. Central Research Laboratories. Furnace measurements show that the steel is generally supersaturated with oxygen and that oxygen contents vary considerably from heat. to heat. Ladle measurements also show considerable heat-to-heat variations. Analysis in terms of ladle deoxidation chemistry differentiates between carbon monoxide controlled and manganese silicate controlled oxygen levels. Deviations from these levels are sometimes due to aluminium present in other added ladle alloys but in some cases the plant applicability of laboratory derived equilibria is questionable.

Jan 1, 1972

The Charters Towers 1:250 000 Gravity Data Set represents a new initiative of the Department of Resource Industries (DRI, formerly Queensland Department of Mines) to provide high quality regional gravity data over areas of the State that have high potential for new mineral discoveries. The Department has adopted a strategy to upgrade geophysical data to complement the ongoing Regional Geological Mapping Program (RGMP) of this Department and in areas where the data would be of most benefit to the mineral exploration industry. Part of this strategy is to ensure that these data are released within 6 months of data collection.The 1989 Charters Towers survey was completed as a joint project with the Bureau of Mineral Resources, Geology and Geophysics (BMR), and is the first regional geophysical data acquisition project undertaken by the DRI. Prior to this survey, the only gravity data in this area dates from the B MR regional surveys carried out between 1960 and 1967.

Jan 1, 1990

By Eldridge B. J

During recent years, Central Queensland has experienced a boom in its coal mining industry. This has involved many companies in projects requiring large capital expenditure. As with most projects of this size, many operating problems are now being experienced which were unforseen at the feasibility stage. One of these problems is the failure of pit slopes and spoil piles at some of the strip mining operations. There have been serious stability problems associated with Utah Development Company's strip mining operations in Central Queensland, in particular the Goonyella Mine. A field investigation programme was under- taken to determine the cause of highwall and spoilpile slope failures. Spoilpile failures were found to result from weakness near the spoil/floor contact zone. Highwall failures were found to result from a combination of unfavourable bedding plane dips and weakness, and the presence of joints in weak o~erburdep; Satisfactory solutions fa the staiity, problems are difficult to formulate, and-field stability experimentation is still at an early Stage.

Jan 1, 1974

By Bhattacharyya A. K

In this paper, the current methods for predicting surface subsidence due to underground coal mining are evaluated first. A single index, called a strata parameter (P), is then proposed to describe the overall character of the undermined strata in the context of surface subsidence. Based on the strata parameter, a method for predicting the maximum surface subsidence for various panel width (w)/depth (h) ratios is presented, which has been tested against specific empirical curves or data from several coalfields in different countries. From the data relating to several coalfields, a linear relationship between the reported average angle of draw and the strata parameter has been established. It has also been found that the strata parameter can be used for studying the locations of the inflection points and the shapes of transverse subsidence profiles.

Jan 1, 1995

By Butt C. R M

Resurgence in Au exploration during the past decade has been characterised by a considerable emphasis and dependence on geochemical procedures. This has been made possible, firstly, by marked improvements in analytical sensitivity over those previously available and secondly, of particular importance to exploration in Australia, by a better understanding of the distribution of Au in the regolith, which has led to the optimisation of sample media. These developments have given exploration companies the ability to seek and detect subtle and widespread geochemical signatures of concealed Au mineralisation and provided an enhanced capability to interpret the data. As a consequence, several new discoveries have been made, even in areas that have been intensively explored in the past. In the deeply weathered Yilgarn Craton (WA), and in equivalent areas elsewhere in Australia and overseas, Au has accumulated in the upper lateritic gravels and duricrusts of the regolith, probably during humid climatic periods in the Tertiary. The laterites may not only be Au ores in themselves, but research by CSIRO and CRC LEME has shown them to be very important sample media, (eg Anand and Smith, 1992). In many areas, however, the laterite has been eroded and hence is unavailable as a sample medium and chemical modification under more and conditions since the Tertiary has leached Au from the upper saprolite. This has greatly increased the difficulties of exploration, particularly where reliance was placed on sampling between 2 and 15 m of the surface. Further research, however, has demonstrated that, despite this leaching, recent remobilisation of An has caused it to concentrate in a specific soil component, pedogenic carbonate, usually in the top I - 2 m, thereby giving surface expression even to mineralisation that is concealed by over 20 in of leached overburden. Secondary carbonates, commonly referred to as calcrete, may precipitate as calcite and/or dolomite in regoliths where the average annual rainfall is less than about 600 mm. Pedogenic carbonates are those that form in unsaturated (vadose) soil horizons. They are widely distributed in the Gawler and Yilgarn Cratons. In the Yilgarn Craton south of about 30¦S ('the Menzies Line'), they are seemingly more abundant over more basic rocks and towards the south east (Figure 1). In contrast, groundwater calcretes form in saturated (phreatic) environments, typically in the axes of major drainages north of the Menzies Line. These are known to accumulate economically-significant grades of U but not, apparently, An.

Jan 1, 1997

By K-S Kim, C-Y Kim, D-G Kim

In tunnel construction or other underground construction, a detailed knowledge of the rock mass ahead of the face is essential for both safety and efficiency of work. Many tunnel collapses have been reported to occur because of lack of appropriate information, such as the geological conditions ahead of the tunnel face. One of the methods which can identify rock mass conditions is the application of drill monitoring data obtained from blasting drill holes, which can detect abrupt and unexpected changes in ground conditions, geological structure and the mechanical and physical properties of rock mass. This paper presents a new approach to how drill performance parameters can be used for prediction of geological conditions ahead of tunnel face. The predictions are based on monitoring the drill parameters of instantaneous advance speed, torque and tool pressure. In order to assess conditions ahead of tunnel face, tunnel seismic profiling (TSP) and a horizontal boring investigation were undertaken and the obtained data compared to the drilling data. The predicted results using drilling performance parameters correlated well with geological conditions ahead of tunnel face.

Jan 1, 2008

By Komosa T, Muir D. M

Mixtures of ammonia and cyanide at low concentrations leach gold selectively from copper-gold ores. The effects of various reagent compositions on three different ore types containing between 0.3 - 1.5 per cent Cu are reported. It is shown that the results and optimum compositions vary according to the ore, which is attributed in part to the mineralogy and adsorption of solution species on the mineral surfaces. The solution chemistry of the Cu-NH3-CN system indicates that Cu(CN)a - and Cu(CN)3 species are involved in the leaching mechanism. Rotating disc studies on pure gold and copper are reported which show that the Cu(CN)32- species leach gold at about half the rate of CN but leach copper at the same rate. The presence of ammonia retards the leaching rate further. Mixtures of Cu(CN)a3- and NH3 effectively leach gold from Telfer tailing without leaching copper. The role of ammonia appears to be to control the precipitation of copper rather than the kinetics of leaching.

Jan 1, 1991

By Bevan JE

The US Bureau of Mines is conducting research to improve the health and safety for underground coal miners, and the efficiency of the mining systems that are used. In 1986, the Bureau began a major research effort on the technology for computer-assisted mining systems for underground coal mines. The initial target was technology for continuous mining machines that would allow them to extract coal by computer-assisted operation. Technology areas being investigated include guidance systems, machine condition systems, computer systems, machine control, human-machine interfaces and planning. In each of these areas, individual system development has progressed to where underground testing of these systems will begin in 1991.In addition to coal extraction, the Bureau has also begun research for the development of technology for computer-assisted roof bolting. The Bureau is developing technology for a "smart" roof bolter that would be able to sense and analyze strata conditions to determine the requirements to provide a competent roof. The system would determine the location of the hole, drill the hole to length, and select and install the appropriate bolt.

Jan 1, 1991

By S Pollak, A Amon

This paper describes the current and finished design work which has been performed for shallow rock station caverns for New York CityÆs first new subway construction in 60 years. A new robust, sophisticated, design procedure has been developed for two up to 30 m wide caverns, with overburden of less then 12 m, and rock cover to span ratios (C/S) in the order of 0.25. The design is based on empirical input parameters like the Q-value, rock mass rating (RMR) values, rock mass class after Cording (1984), cover to span ratios, which have been validated by the use of structural computer models as well as two- and three-dimensional numerical discontinuum models. The design approach is a staged approach using first principles, empirical models and non-linear FEM and DEM models. In addition, the paper describes the factors and circumstances why shallow caverns have been selected instead of cut-and-cover structures and why all the underground station structures have been developed as drained structures.

Jan 1, 2008

Synthetic seismograms of reflectivity method and some field records available are studied to detect the amplitude anomalies at the interface of the gaothermal reservoir the gas and/or oil boundary, and the underground tunnel. The first arrival of PO wave on the P-SV record are weak and emergent while those of P wave only rotated with respect to an incident angle are clear. This can, be explained by means of the energy loss of P-SV wave conversion. The primary reflections of P waves about depth fade away as compared to SH waves which do not perform any conversion, although they hold high attenuation in the fully saturated fluid layers. Reflection of comparable strength is present at the P-wave and S-wave... boundaries, but gas-saturated zones correlating with P wave bright spots do not show equivalent attenuation anomalies. Thus the comparative technique of P-SV wave and SI i wave records is very useful to indicate the strong amplitude anomalies at the boundaries of sealing targets.

Jan 1, 1990

By Sijing Cai, Chengpu Zhou

The requirement of mineral resources is increasing as the economy is continually increasing in China. The mining practices of various complex sulphide deposits and precious metal deposits, and the treatment of mine tailings and other industrial solid wastes, have greatly improved fill quality in the metal mines. From early-1980s, high density slurry fill, paste fill of total tailings, low density slurry fill with addition of silicate gelling agent, etc has been studied and applied, and some progress has been achieved. Today, mine tailings, slag and power plant ash are widely used as fill materials in mining. A number of cemented fill mines equipped with large capacity trackless mining machines are in production. Recently, The 3rd Chinese National Symposium on Mining with Backfill, 1995 has been held, the progress of fill technology in mines has been exchanged and summarised. In the paper, some aspects of fill technology used in the metal mines of China are briefly introduced and some applications of fill research work are presented.

Jan 1, 1998

By Z B. Rakisheva

By explosion rock mass behaviour is conditioned by preset complex of rocks natural characteristics. Very important role of blockness, which is percent (share) content at examining massif of natural separatenesses of different dimensions and configurations, separated each from other by the cracks of geological and technogene origin. Besides natural properties of massif the power, detonational characteristics of applied explosives, parameters of explosives charges disposition at massif and technology of explosion influence vastly at lumpiness (granulometric structure) of exploded rocks. The mathematical model of rock mass destruction by explosion had been elaborated and substantiated. It ties mutually the initial data (rocks properties, parameters of the charges disposition) and final results of explosion (granulometric structure of exploded rocks). The program of this complicated problem solving had been compiled. Analysing the received results of the problem solving, one can reveal contribution of each group of influence factors for lumpiness of exploded rocks. This fact creates preconditions for elimination or diminution of negative role of some controlled initial data.

Jan 1, 2003

The paper re-visits an old and proven concept of winzing, a method widely used in the past to gather exploration data for accurate definition of the orebody. It is proposed to use a mobile Supersucker (a giant vacuum cleaner also known as vacuum lift), to carry out winzing activities underground. A brief description of conventional underground winzing used in the past is provided, together with a discussion on other underground bulk exploration methods used in Australia to date. Historical background, principles of the proposed system, Supersucker construction details and productivities, and benefits and advantages of the proposed system in comparison with other exploration methods, are outlined. Other relevant applications of the mobile Supersucker, including surface winzing, are also briefly discussed in the paper. With a view of using the mobile Supersucker to recover all broken ore stocks underground, included are also results of floor sampling conducted recently in the in-stope decline excavated in a coarse gold type, high-grade orebody.

Jan 1, 2002

By T Akiyama, J A. de Castro, H Nogami

Blast furnace is a countercurrent moving bed reactor that produces pig iron from iron bearing materials like pellet, sinter or lump ore. The furnace has cylindrical shape and the lump solid materials are alternatively charged onto the top of the furnace. Hot air is introduced through tuyeres that are set on the lower furnace wall. Auxiliary fuels (pulverised coal, oil or natural gas) and raw materials (fine ore or fluxes) are injected into the furnace with blast air from the tuyeres. In front of the tuyeres, coke particles react with oxygen in the blast air and generate carbon monoxide. The hot reacting gas heats up the lump solids and reduces iron oxides in the upper furnace. In the middle height of the furnace, the reduced iron and slag are fused by the combustion heat and form the cohesive zone. The molten iron and slag that are generated in this region trickle down through the packed bed of coke particles and flow into the bottom of the furnace. Therefore, the flows of gas, lump solids and liquids exist at the same time in the lower part of the blast furnace.

Jan 1, 2000