Search Documents

By Mould G. R

The paper presents a general background to the subsidence research programme being undertaken by the Department of Mineral Resources and Development in New South Wales. The results of the studies undertaken over the last ten years are summarised. The differences between these results and those obtained by the National Coal Board are discussed. The results of a study carried out on the effect of total extraction beneath a freeway in the southern coalfields are discussed in some detail. The procedures developed for the const- ruction of a 500 mm diameter natural gas pipe- line crossing a number of collieries in the northern coalfields are also outlined. The future direction of the Department's subsidence research programme is discussed.

Jan 1, 1980

By J Kok

"In some underground mines it has been observed that the primary focus during feasibility studies is to determine the best way to mine the defined orebody. Some studies have been conducted without sufficient consideration of the ventilation and cooling requirements or the risk from exposure to associated airborne pollutants caused by the mining operations.Following the hierarchy of control to manage risk, numerous problems of the ventilation systems in some underground mines could have been avoided if sufficient consideration was given to the ventilation requirements to manage heat, airborne pollutants and leakage during the feasibility study phase. If the constraints and hazards were well defined and understood at the time of the study, efforts could have been made to eliminate or substitute the hazards to decrease the risk. Some of these problems include but are not limited to: primary fan locations heat loads diesel exhaust ventilation design based on the production requirement fire/emergency response strategies.This paper highlights areas in the ventilation discipline that are sometimes overlooked during feasibility studies. It will also highlight the importance of the Ventilation Specialist during these studies. Experience and knowledge of best ventilation practices must be applied in feasibility studies.As a result of adequate consideration to all ventilation aspects in the feasibility study phase, risks will become lower in terms of health, safety, production loss and equipment downtime caused by heat.CITATION:Kok, J, 2014. Feasibility studies – what should be considered in terms of ventilation, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 197–204 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By Schommarz KH, Dunne RC, Goodall CM

Column cells are widely used today for the recovery of base metals by flotation. Their use for the flotation of iron sulphides has not been as rapid. Australia has pioneered the use of large rougher flotation columns. During the last six years, seven rougher columns have been installed on gold mines treating iron sulphides and the technical viability of this technology has been demonstrated. Laboratory column testwork on a gold bearing iron sulphide ore demonstrated the effects of both physical and chemical parameters. In general the large commercial columns operate over a broad range of conditions depending on the downstream treatment of the flotation concentrate. The addition of wash water to commercial columns is not universally applied and there appears to be a need for a better wash water System.

Jan 1, 1993

By Gillies A. D S

A device has been developed for modelling the behaviour of coal under conditions which may lead to spontaneous combustion. It is designed to model the behaviour of a stockpile of large mass. The apparatus can test coal samples taken from the flow stream from mine through washing, stockpiling and transportation to the point of utilisation. It tests samples in an as received' condition and so takes into account the effect of aspects such as particle size and moisture content on propensity for spontaneous combustion to occur. Results of the preliminary tests undertaken are given and future applications of the apparatus are Discussed.

Jan 1, 1995

By Sirayanone S, Rashad MZ

An important problem occurring in the iron and steel industry of Egypt is the presence of manganese oxide and chlorine with different percentages in the Bahariya Iron Ore Deposit, Western Desert, Egypt. In this work we used a geostatistical method known as the Volume- Variance Relationship to predict grade fluctua- tions of Fe% , Mn% and Cl% in the ore after blasting a certain volume from the ore deposit, on the other hand, if we have a certain limit for each of these chemical components, we can select the bench blasting dimension to give these limits.

Jan 1, 1986

With the advent of the resources boom in the late-1960s most of the larger scale resources projects in Australasia were commissioned on an æowner miningÆ basis, where the mine owners owned and operated the primary mining equipment. Then, in the 1980s with the arrival of the gold mining boom in Western Australia and elsewhere, a change occurred û most of the mining activities were carried out on a contract mining basis. Over recent years, however, there has been a marked trend amongst larger Australasian open pit mining operations back towards owner-controlled and operated mining operations. The reasons for this are many and are addressed in the paper, but centre on the concept of the owner being prepared to assume more of the mining risk in exchange for the advantage of not having to pay a contractorÆs profit margin. Where mining contracts are entered into, the older æschedule of ratesÆ format is being replaced with less adversarial and more entrepreneurial contract alternatives involving operating cost and risk sharing in a spirit of æfair dealingÆ. Leasing and maintenance issues have also been influenced in recent years by the advent of more flexible contract arrangements with equipment suppliers. Group purchasing has also had some influence for project operators. For many mine owners, the optimal risk management profile involves a practical offsetting of the assumption of mining risk on the one hand, against the removal of litigation risk and potentially reduced operating costs on the other. Potential pitfalls may arise where equipment size and type requirements vary with time or where manpower management, mining flexibility, job skills or safety exposure factors are relevant. These issues are commented on in the context of some well known examples, and an update is provided on contract mining versus owner operation in large-scale Australasian open pit mining generally.

Jan 1, 2002

By Bhattacharyya A. K>

The Pemali Open Pit Mine is situated in a small island called Bangka in Indonesia. It produces approximately 165,000 m3/year of tin ore with an average grade of 3.67 kg/m' of tin from a primary deposit. The deposit occurs at the rim of a granitoid intrusion within sedimentary beds. The rock formations, all extremely weathered, and the overlying alluvium, are exposed to a rainfall exceeding 3m/year. Serious slope stability problems are experienced at the mine, despite using overall pit slopes of 20¦-29¦, the latter resulting in a stripping ratio of 4:1. This paper outlines a computer based back analysis of a major slope failure involving some 250,000 m' of material which occurred on the west wall of the pit in February, 1984. The findings from the analysis, together with other information, are used to examine the stability of the east wall of the pit, where tension cracks developed later. The results indicate that the large influx of water was the most significant cause of such slope stability problems and a more intensified water management programme would be beneficial.

Jan 1, 1989

By Richardson G. W, Yap L. C

Friction rock stabilisers (FRS) are steel-based, thin-walled tubular ground reinforcement widely used in underground mines in Western Australia. Following installation these stabilisers are subject to corrosion which may reduce the load carrying capacity and lead to unexpected ground falls. Although corrosion has been recognised as a common occurrence, particularly under aggressive mine water and mineral conditions present in underground mines, the knowledge of the effects of corrosion on the mechanical behaviour of FRS is limited. The Department of Minerals and Energy of Western Australia has conducted a laboratory based program of studies to investigate the effect of corrosion on the mechanical properties of FRS. The studies have focused on the effect of corrosion on tensile strength of FRS and frictional resistance along the interface between FRS and the drillhole wall. The results indicate that under certain conditions corrosion damage can significantly reduce the effectiveness of FRS.

Jan 1, 1996

A biological column leach testwork program was undertaken on a chalcocite ore. Three tests were conducted in all, using 65 in x 100 mm columns in three sections. The tests were started with varying acid strengths and inoculated with bacterial solutions from previous column testwork. The leaching of Cu was found to occur in three stages. These stages consisted of direct acid leaching, bacterial oxidation and ferric iron leaching. These leaching stages can most easily he described through the examination of not only Cu dissolution but also Fe dissolution and its subsequent oxidation and precipitation. The p11 of the system was found to he critical in establishing and maintaining the bacterial leaching system. The oxidation potential was seen to he influenced by the leaching system as the oxidation states altered. Test variables such as, 02, COz, and temperature were all found to influence the system. Final copper recoveries were in excess of 90 per cent in each column test over a leach time ranging from 211 to 328 days. Given similar leach conditions are applied, the application of this technology to site is expected to give comparable results.

Jan 1, 1994

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

By Singh RN, Yuejin LI

The problems experienced with longwall mining machinery motivate the development of an expert system for fault diagnosis. The techniques of knowledge representation, database, knowledge base and inference engine guide the selection of the expert systems and languages -"Turbo Prolog"- as exemplified in the case study of hydraulic support. The aim is to hasten future development of a fault diagnosis system and the design of a system to locate and determine the causes of failure of longwall machinery. The system would use its stored case history and other information to make fault diagnoses and suggest appropriate remedies. Consequently down-time would be reduced and production and profitability should increase.

Jan 1, 1991

By Pinn N

Geosynthetics is an all encompassing word to describe a number of man-made products usually from hydrocarbons which are used in conjunction with the soil. The specific products are:Geotextiles Geomembranes GeonetsGeogrids GeocompositesIn mine establishment and associated construction work, Geosynthetics have proven to be successful in a wide range of applications. For example, geotextiles are now used to assist with the establishment of access roads, site preparation, haul roads and in connection with the construction of embankments for storage ponds and dams as well as for general hydraulic and foundation engineering problems.

Jan 1, 1990

Selection of the mining method and most appropriate mine layout for deep open cut coal mines is discussed, giving particular attention to the types of mines expected to be developed in the future in Australia. Because of the more complex nature of these operations a large number of alternatives for mine design are available, and the constraints associated with these designs are discussed. Potential problems to be overcome are identified to allow setting of realistic targets for maximum output and build-up production rates.

Jan 1, 1981

By Slattery T. E

Recent develognents in zinc flotation at the North Broken Hill Limited concentrator are discussed. An outline of the history of zinc flotation and a description of current practice is presented. Installation of on-stream X-ray analysis probes has resulted in inproved metallurgical performance and focussed attention on automatic control. Results are presented of investigations made over the past six years which have led to the formulation of experimental schemes for the automatic control of zinc flotation.

Jan 1, 1983

By Scaife PH, Cripps Clark J, Cameron DB

Tuyere coke samples have been taken through the tuyere openings of B.H.P. International Blast Furnaces since 1978 with Whyalla No. 2 Blast Furnace taking samples on a regular basis since 1982. The degradation of coke during it's passage through the Blast Furnace can be measured and the relationships between these data, feed coke data and blast furnace operating data demonstrated. Tuyere coke sampling has been useful in revealing misleading external coke testing results and is still the method to monitor directly the performance of coke within the Blast Furnace.

Jan 1, 1987

By Marshall T, Nicholson DS

Reserves of high-grade quartz gravel, lignite and timber suitable for the production of silicon metal and ferrosilicon on large scale occur within 40 miles of Bluff Harbour. Undeveloped hydroelectric power resources on the Clutha River are located within 50 miles of the most promising quartz gravel deposits while ooencastable lignite, potentially suitable for electric power production, occurs in the same locality as the quartz gravels. A preliminary study of production economics indicates that the commercial feasibility of silicon/ferro-silicon production would depend mainly on the cost of electric power, total capital cost of plant, and the market value of the products. The proximity of Bluff Harbour is advantageous for the export of products.

Jan 1, 1971

By Mercer J. K

Shaft guide reaetions in No. 2 Ore Shaft, Mount Isa Mines Limited, have been reduced to a low order of magnitude by the use of self aligning slippers and spring loaded guide rollers. Before commissioning the new 4500 h.p. winder at No. 2 Ore Shaft in January, 1958, it was realised that the increase in hoisting speed from 1800 to 2650 ft/min. would cause high shaft guide reactions which would be increased further when the elongated 12 ton skips replaced the existing 7 ton skips.The Cambridge accelerometer was used to measure the shaft guide reactions and to confirm that progressive skip modifications were resulting in reduced reactions. The skip modifications were completed in 4 weeks.INTRODUCTIONIn 1956 an expansion programme was initiated to increase production from 5000 to 11000 tons per mining day. At No. 2 Ore Shaft the 1500 h.p. winder operated at 1800 ft./min. and hoisted a 7 ton capacity skip. The new 4500 h.p. winder operates at 2650 ft./min. and hoists a 12 ton capacity skip. No. 2 Ore shaft is equipped with two 5 ft. by 5 ft. hoisting compartments (Fig. 1) and any increase in skip capacity meant an abnormally long skip. This feature, coupled with the increase in hoisting speed, could have caused very high shaft guide reactions. Before commissioning the 4500 h.p. winder, a Cambridge accelerometer was borrowed from the University of Adelaide and was used to measure the shaft guide reactions. Rather than carry out an extensive shaft timbering programme, the skips were modified by fitting cushioned guide shoes and spring loaded guide rollers (Fig. 1). Testing commenced in February, 1958, and was completed in March, 1958.

Jan 1, 1961

The Shamrock Gold Mine has been brought from exploration to production within three years. Mining of the openpit is scheduled for June 1990 with commissioning in April of the 180 000 TPA carbon-in-pulp mill on old tailings and rock dumps. The development of a small openpit containing 344 000 tonnes at 3.6 g/t Au in a complex sulphide ore has required extensive metallurgical testwork to optimise recovery, and ensure profitability. The project has been undertaken in a changing economic climate, with increasing restrictive legislation. The decision to mine was further complicated by the escalating cost of installing a heap leach operation in South East Queensland. Decreasing costs of consumables, in particular sodium cyanide, and the opportunity to purchase a suitable transportable mill at a reasonable price made the project robustly viable as a CIP operation.

Jan 1, 1990

By Ramsden AR

The ability of the scanning electron microprobe to provide non-destructive qualitative and quantitative mineralogical analysis at the micrometre scale makes it a very versatile tool for the mineralogical characterisation of ore deposits and their host rocks. With the trend towards exploitation of large tonnage low grade depositsnd precious metals at the parts per million level it is becoming increasingly important to have full mineralogical characterisation and knowledge of the mineralogical residence of the valuable elements to assist formulation of a cost-effective exploration program and obtain optimum recovery in the case of exploitation. Mineralogical applications include

Jan 1, 1989

By Doxford CI, Perry AJ

Mining Lease 908, situated on Gorge Creek near its confluence with the present Cape River system, has been subjected to intensive recent exploration for alluvial gold.The gold is hosted by a buried palaeochannel, the Gorge Creek Lead and by an overlying remnant meander of the Cape River. The principal, if not sole, sources of gold within the Gorge Creek Lead are the northwest trending Great Australian Reef and Green's Specimen Reef systems which are situated on adjacent high ground. Lower grade gold bearing eluvial ground separates the reefs from the Gorge Creek Lead. The sources for gold within the old Cape River system channel (Canton Lead) are thought to be situated some distance upstream, one source perhaps being the Lolworth Diggings located 30 kilometres to the northwest.Exploration of previously "heavily dug" ground on both leads consisted of detailed geological mapping followed by the collection and treatment of bulk samples from eight costeans. The wash samples varied in size from 120 to 396 cubic metres. Treatment was undertaken through a commercial sized conventional wet screen and jig plant.

Jan 1, 1986