Search Documents

By H Zorychta

Based on underground measurements made at the Nova Scotia coal mines of the Dominion Coal Company, Limited, this paper presents a comparison between the physical properties of hardwood packs and steel friction props when used for longwall support. The probable loads sup-ported by steel friction props on a longwall face at both the Dominion No. 20 Colliery and the Princess Colliery are delineated, and the results of the tests are presented in graphical form. It is concluded that the steel friction props are more efficient than the hardwood packs that they replaced as roof supports. Introduction AN evolution in the methods of longwall face support is taking place in the Sydney coalfield. Longwall face support had consisted primarily of timber props and hardwood packs. In 1957, however, at the Princess Colliery, Sydney Mines, Nova Scotia, the first longwall was equipped with steel friction props. At the present time, eleven longwall faces are supported on wood and sixteen faces are carried on steel friction props.

Jan 1, 1965

By L. J. Cunningham

Introduction The property of Rouyn Merger Gold Mines, Limited, is in Rouyn and Joannès townships, Western Quebec, seven miles east of the town of Rouyn. Traversing it is the east-west trending Cadillac-Bouzan fault. Diamond drilling in 1944 and 1945 along a shear zone south of the fault indicated an ore deposit lying at the contact between sedimentary and volcanic rocks and dipping approximately 60° to the northwest. In the summer of 1945 it was decided to sink a shaft to investigate the indicated ore zone. In the immediate vicinity of the deposit, bed-rock is overlain by clay beds, in some places as much as 70 feet thick. Consequently, possible shaft sites were limited to those locations where overburden would not be excessive. The most favourable site was about 125 feet to the south of the ore zone as projected vertically from bed-rock to the surface. Accordingly, it was decided to sink the shaft at this point, with an inclination of 60° N. W., paralleling the dip of the ore zone.

Jan 1, 1948

By Louise Pearce

?Environmental and social impact assessments (ESIAs) are: ??process-driven and scientific processes ??The process entails a number of steps and procedures which result in obtaining a licenceto operate ?and moving more towards a social license to cooperate. ?However, the primary premise of ESIA is to facilitate the consideration of environment and the communities in planning and decision-making which would ultimately make it possible to arrive at decisions that are ?sustainable?. ?Hence, ensuring the development of the mining sector on a sustainable basis is a critical challenge that needs to be addressed by the global community.

May 1, 2011

By Hamid-Reza Manouchehri

Mining & Sustainability? A Paradox?! ? Production: gradually or exponentially increasing (giant mining) ? Ore Grades: gradually declining, ? Open Cut Mining: now widespread, likely to be sustained in the future though the long-term is hard to predict as new mineral deposits are likely to be deeper ? Waste Rock / Overburden: increasing rapidly, likely to be sustained in the future and closely linked to open cut mining, especially for coal and base metals ? Economic Resources: commonly increasing but some remain stable or gradually declining, future is linked closely to exploration, technology and economics; Increasing population, changing life style and technology development, ultimately result in sustainability in mining industry to hang in the balance and continue.

May 1, 2013

By Staff

One hundred thousand miles of flying over the North country without a single air casualty; much of it over virgin territory probably never before visited by white men; some of it over regions that abound with possibilities for minerals; all of it effective, for exploration and the establishment of bases and supply-stations, and for the carrying of men and their tools and provisions- this, briefly, is the record of Northern Aerial Minerals Exploration, Limited, a Canadian company organized Jess than nine months ago, which has been functioning, without interruption, during spring, summer, and now into winter. Our planes have ranged from the Alaskan boundary on the west to the Labrador coast on the east, and from the Transcontinental railway north to the Arctic circle. Our prospectors, carried on trips of hundreds, and occasionally thousands, of miles, have gone over large sections of country which were never before explored, and at the end of the prospecting season the Company finds itself in possession of several groups of important gold claims, which look most promising. In addition to this, we have been in contact with deposits of almost every known mineral.

Jan 1, 1929

By A. M. Childs, R. F. Mather, K. R. Rawling

"The challenges encountered in the design and construction of mines and their process facilities today are becoming more intense and the engineering more competitive. The need to incorporate new techno1ogy to compensate for ever rising costs is always present, but its application in the harsh environment of Northern Canada increasingly requires the inclusion of new proven methods and innovative approaches to arrive at economically attractive projects.This paper deals with the development of the process design for the Cullaton Lake Gold Mine in the Northwest Territories. Particular emphasis is given to the interaction of the imposed construction and testwork schedules, and their effect on certain process decisions.The challenge that faced the project team may be defined by the following factors:1. A schedule which required that metallurgical testing, engineering, and procurement and delivery of all equipment and construction supplies should be complete within a period of ten months.2. Transportation of all personnel, equipment and supplies to the site by airlift, as no road was available or affordable.3. A six week period when transportation to the site was impossible.4. The extremes of temperature beyond the tree line in the Northwest Territories.5. A complete lack of infrastructure in the area."

Jan 1, 1983

By P. D. Kondos, J. R. Goode

Given the global inventory of low grade and refractory gold deposits, processes that could turn these challenged deposits into mines are of considerable interest. Such gold deposits have low value and potentially high operating costs and so they pose special challenges for the mining engineer and metallurgist. Conventionally, refractory gold ores have been processed by whole ore pressure oxidation and roasting, or flotation followed by roasting, pressure oxidation or bio-oxidation of the concentrate. Halide-based processes have recently been developed that might be applied to concentrates. Low grade refractory gold ores have been processed using heap bio-oxidation followed by cyanide heap leaching or milling. Other processes are emerging. Barrick has completed an inventory of emerging technologies (1). A summary of the current status of these developments will be presented with the view that, with additional development, some of these technologies or a combination thereof may unlock the value of these deposits.

Jan 1, 2005

By H. Marquis

The present paper consists of a survey of the literature on the problems of abrasion and wear of metals and materials by suspended matter. This problem is a very general one in industry, and is especially notice-able in the operation of cyclones and other types of dust collectors. The problem of abrasive dust in corrosive gas environments, such as commonly encountered in metallurgical industries, is particularly severe. Very little work has been done in the study of this type of abrasive wear, especially at high temperatures. However, a general review is presented here of all the work published on related subjects, such as that involving sand erosion in turbines and water wheels and the effect of temperature on friction wear. Topics in this paper include: blasting wear by sand, quartz, limestone, silicon carbide and other refractory particles; methods of investigation; effects of velocity, temperature and *Canadian Armament Research and Development Establishment, Valcarter, P.Q. angle of attack; correlation between indentation hardness, scratch hard-ness and resistance to abrasion; the effect of protective coatings; resistance of various metals; etc.

Jan 1, 1962

By K B. Bowley

This paper covers the application of a systematic maintenance plan by the Plant Engineering Department of Rio Algom Mines Limited, Milliken Division. The plan established the function of work study, developed and installed formal work planning and labour cost control procedures, and extended the existing preventive maintenance routines. In June, 1961, assisted by management consultants, a more scientific approach to maintenance was instituted. The emphasis was placed on the control of labour. The development and application of the primary control system was established with-in six months. Since then, the Department has operated for a year, consolidating the system. The procedure of the installation, the results achieved and the results to be expected will be discussed. JNTRODUCTION THE Milliken Division of Rio Algom Mines Limited operates a 3,000-ton-per-day uranium mine, in the Elliot Lake district of Ontario, which went into production in April of 1958. The lowest operating level is 3,000 feet below surface. Mining is carried out by open stopping, with planned pillar support and footwall haulage on rail.

Jan 1, 1963

By Manjeet Chowdhry, Qingxia Liu, Phillip Choi, Zhenghe Xu

Computational chemistry methods, such as density functional theory (DFT), are powerful tools to quantify reagent-mineral interactions encountered in sulphide mineral flotation. A quantitative relationship between theoretically calculated parameters based on chemical structure of collectors and their reactivity with different metals/minerals can provide valuable insights for design and development of more powerful and tailor-made reagents offering enhanced metal/mineral selectivity. DFT calculations at B3LYP/6-311++G(3df,3pd) level were employed to elucidate the reactivity of neutral sulphide collector reagents, including thionocarbamates (TC), thioureas (TU), xanthogen-formates (XF), dialkyldithiocarbamates (DTC) and dialkyltrithiocarbonates (TTC) with different heavy metal ions (Cu2+, Zn2+ and Pb2+) in solution. The extent of delocalization of lone pair electrons of heteroatoms (attached directly to C in C=S) over C=S group was found to be the dominant factor in determining the collector’s reactivity. Order of reactivity was established as: TU > TC > XF > DTC > TTC. All the collectors showed superior affinity towards copper followed by lead. Unidentate binding was observed through sulphur atom except for xanthogen-formate for which bidentate binding mode was observed. Effect of nature of substituent groups at N and/or O atom on reactivity of thionocarbamate and thiourea was also investigated. The results obtained through DFT calculations are consistent with the experimental data reported in literature.

Jan 1, 2015

By G. S. Dobby, J. A. Finch

"I. INTRODUCTIONA significant development in flotation over the past few years has been the increasing industrial use of flotation columns, primarily in Canada. The column differs dramatically from conventional mechanical flotation machines, both in design end operating philosophy, which has been a principal reason for its slow acceptance by the mineral industry. Boutin, Tremblay and Wheeler (1. 2) developed the concept in the early 1960's and since then plant and laboratory columns have been marketed commercially by Column Flotation Company of Canada Ltd. In 1980-81 at Mines Gaspe, Quebec, three columns replaced 13 conventional cleaners in a molybdenum upgrading circuit, with superior results (3). Since then many of the copper producers in British Columbia have installed columns for copper and molybdenum cleaning, including Gibraltar, Lornex, Highmont and Island Copper. There now appears to be widespread interest in flotation columns.The column is particularly attractive for applications involving multiple cleaning stages and can upgrade In a single stage compared with several stages of mechanical cells. This results in simpler, more controllable circuits. Importantly, the column itself is well suited to computer control. A significant problem, however, has been that of translating laboratory data to plant performance. The purposes of this communication are to address the problem of column scale-up and to describe some of the transport mechanisms of a flotation column, leading to a kinetics based model.A schematic of a flotation column is shown in Figure]. Industrial columns are up to 13 m high and 0.3 to 1.8 m in cross section (either square or circular). Three zones can be identified:a collection zone, with feed entering 2 to 3 m below the top of the column and descending against rising bubbles generated at a gas sparger; a washing zone, where a packed bubble bed is generated by a downward flow of wash water; and a conventional froth (2 - 5 cm thick), the sole purpose of which is particle transport to the launder. The tailings withdrawal at the bottom of the column is controlled at a rate slightly greater than the feed flowrate (called a positive bias).An important element is the washwater, added just below the froth zone. The component of the washwater that flows downward (to make up the bias) is sufficient to prevent coalescence of rising gas bubbles. The packed bubble beg so generated is very efficient at suppressing gangue entrainment to the concentrate."

Jan 1, 1985

By L. López

Argentina reported about 40,000 tonnes of uranium (tU) as reasonably assured resources and inferred resources for the production cost category <130 US$/kgU in the OECD-NEA/IAEA classification scheme. These resources belong to the following projects: Sierra Pintada, Cerro Solo, Don Otto, Laguna Colorada, Laguna Salada, Meseta Central and Amarillo Grande. With three heavy water reactors in operation and an approximate installed capacity of 1.7 GWe, the current natural uranium requirements are about 220–250 tU per year. Based on various nuclear growth scenarios, it is estimated that by 2030 there will be a generation capacity of some 3,092 GWe for the reference case, with raw material needs of some 486 tU per year. Currently, there are no perspectives for local uranium production in the short term, and it is thought that uranium projects with identified resources must complete resource delineation and advance in technical pre-feasibility studies for the recovery of uranium. It is expected that Argentina continue meeting the uranium demand with imports in the next following years. In the Latin America region, both Brazil and Paraguay could be considered as potential uranium suppliers. In conclusion, despite the apparent growth prospects for the use of nuclear energy to generate electricity in Argentina, there are no immediate prospects for the provision of uranium oxide concentrates from domestic deposits for fuel fabrication. This has implications for supply and energy security.

Jan 1, 2020

By Q. G. Reynolds, R. T. Jones

The choice of furnace design parameters has a marked effect on the integrity of the furnace that is constructed. The design methodology for DC arc furnaces typically begins with the chemical reactions and feed materials that define the process. The specific energy requirement of the process, and the feedrates of the raw materials largely determine the power requirement for the furnace. A chosen value for the &apos;power intensity&apos; sets the diameter of the furnace. Justification is provided for why this is a good choice of scale-up parameter. Equations are presented to quantify the resulting trade-off between thermal efficiency and the degree of error that can be tolerated in the balance between power and feedrate. This improved understanding should provide a better rationale for selecting an appropriate power intensity (or furnace diameter) for future furnaces.

Jan 1, 2015

By L. Newman, R. Wyrick, R. Berezowsky

The Stillwater Mining Company operates an integrated mines, mill, smelter and base metals refinery complex in Montana, USA for the production of a high-grade platinum group metals (PGM) bearing concentrate, nickel sulphate crystal and cathode copper from the PGM-containing nickel-copper converter matte. The complex was constructed in stages over several years, starting with the mine and the mill, followed by the smelter and finally, a base metals refinery, which was commissioned in 1996. Due to the relatively small quantity of matte production, a straightforward refinery process was initially selected to extract the base metals, which reported to a mixed nickel-copper solution for further treatment off-site, and yielded a high-grade PGM concentrate suitable for treatment in a PGM refinery elsewhere. Subsequently, as a result of increased matte production, the process was modified to separate the nickel and copper, and to produce a nickel sulphate salt and cathode copper. This paper describes the design and operation of the original and the modified processes utilized in the base metals refinery (BMR).

Jan 1, 2004

By Marc C. Bétournay

A mine production locomotive, the world?s first applied industrial fuelcell vehicle, has been designed and tested in the context of a number of proof-of-concept projects supported by the Fuelcell Propulsion Institute, an international consortium of stakeholders dedicated to facilitate the commercialization of fuelcell vehicles. The locomotive?s simple electric-powered motor and controller system was ideal to study a number of requirements related to fuelcell power application: hydrogen power plant operation, underground hydrogen use, risk and regulatory requirements, production performance versus the conventional battery-powered locomotive version under measured duty cycles and production requirements, power plant design improvements for other fuelcell vehicles, and cost-benefit aspects. This article will focus on the design and testing aspects of this project which has led to successful performance demonstrations of the vehicle under surface and underground conditions at two mines. It will also present information on the creation of a safe, reliable and efficient power plant which fulfilled its design objectives, including longer productivity time for a given vehicle fill-up.

May 1, 2003

By John L. Hatton

The author will introduce and describe the nature of Fiberglas-Reinforced Plastics. Successful applications of corrosion-resistant structures will be shown and described, including pipe, ducts, tanks and other equipment. These structures are generally designed to handle corrosive liquids and gases and have proved both satisfactory and economical in service in various industries in Canada. The specification of structures will be discussed in relation to materials, construction and workmanship, physical properties and methods of testing.

Jan 1, 1970

By K. G. Thorne, M. J. McLeod, D. Hoy

"Throughout the Paleozoic, a variety of gold depositional environments were created in the New Brunswick segment of the northern Appalachians because of the complexity of arc and continental plate collisions and subsequent erosion of the orogen. In southwestern New Brunswick, recent exploration and research has focused on deposits and occurrences that can be broadly classified as intrusion-related, generated by late- to post-orogenic felsic to intermediate plutonic rocks emplaced during the Early to Middle Devonian. This work has led to the establishment of models for gold mineralization and guidelines for exploration in this area, which might also be applicable elsewhere in the southern part of the province and, perhaps, throughout the northern Appalachians. The deposits in the vicinity of Clarence Stream in southwestern New Brunswick exemplify this deposit type, and highlight the emergence of a possible major gold district in the region. Durant le Paléozoïque, une grande variété d’environnements aurifères ont été créés dans le segment néo-brunswickois des Appalaches du nord en raison de la complexité des collisions entre arcs et plaques continentales ainsi que durant l’érosion subséquente de l’orogène. Dans le sud-ouest du Nouveau Brunswick, les travaux d’exploration et de recherche récents se sont tournés vers les gisements et les indices appartenant à la classe des gîtes associés aux intrusions, générés par des roches plutoniques felsiques à intermédiaires tardi- à post-orogéniques mises en place au Dévonien précoce à moyen. Ces travaux ont permis d’établir des modèles de mise en place pour la minéralisation aurifère ainsi que des guides d’exploration pour ce secteur, lesquels pourraient aussi être appliqués ailleurs dans le sud de la province et, possiblement, dans l’ensemble des Appalaches du nord. Les gîtes aux environs de Clarence Stream dans le sud-ouest du Nouveau Brunswick sont un exemple de ce type de gisement, mettant en valeur ce qui pourrait devenir un district aurifère majeur dans la région."

Jan 1, 2008

By Milton C. Graves, Marcos Zentilli

"Gold has been reported from most geological environments in Nova Scotia; however, virtually all production (circa 2,000, 000 troy ounces; circa 60 tonnes) has come from that part of the province to the south of the Glooscap Fault which is underlain by Lower Paleozoic rocks of the Meguma Group. Over fifty concordant sets of quartz-carbonate-arsenopyrite veins have seen production. The host rocks are greenschist-grade equivalents of Cambro-Ordovician flyschoid quartz wackes and shales folded and metamorphosed during the Devonian Acadian Orogeny. The veins were emplaced under conditions of greenschist-grade regional metamorphism and under the same conditions of tectonic stress that later resulted in the regional folds and penetrative, axial-plane slaty cleavage. Rapid filling of hydraulic fractures caused by excess metamorphic pore fluid pressure under Acadian tectonic stress conditions can account for the geometry and paragenesis of these veins.The ultimate source for gold deposits in most greenschist-grade domains remains in doubt, but these domains seem to have had ample gold within them available for mobilization. The work done, to date, on the gold geology of Nova Scotia suggests that regional greenschist metamorphism was an effective mobilizer and a potential concentrator of Au, As, W, Fe and S from these vast reservoirs.In rocks of pre-Acadian age north of the Glooscap Fault, gold occurs as an important accessory in volcanogenic massive sulphide ore, as a minor constituent in other types of basemetal concentrations and in one small concordant group of quartz veins.The post-Acadian metallogenetic domain, which overlies and overprints the two older domains, contains small amounts of gold in many mineralizing environments. Veins, with stibnite and gold, cross-cut crystalline rocks. Disseminated gold is present in basal conglomerates of post-tectonic molasse. Gold has been a by-product of Mississippi Valley-type Pb-Zn-Ba-Sr deposits in Lower Carboniferous sedimentary rocks and has been reported with Pb-Zn-Ba-F in veins which cross-cut Lower Carboniferous and older rocks. Small post-glacial placers have also seen minor production."

Jan 1, 1982

By M. N. Bassim, W. W. Tennese

"Concepts of linear elastic fracture mechanics were applied to study two cases of failure, namely an equalizing beam from a tandem rear axle of a highway tractor unit and the main beam of a flat bed trailer. In the first case, the presence of a crack, initiated by stress corrosion cracking followed by significant fatigue crack propagation produced a state of stress which was sufficient to produce brittle failure. Calculation of the fatigue life agreed with the number of cycles that the structure experienced before final fracture. In the second case, it was demonstrated that a combination of low temperature and high loading rate was sufficient to cause brittle fracture.IntroductionFailure analysis of engineering components has generally been carried out without the benefit of fracture mechanics. It is generally understood that real structures inevitably contain internal or surface flaws which under an applied load, may propagate to fracture. Fracture mechanics relates the applied stresses to the crack size in specified geometries. Since its introduction approximately thirty years ago, fracture mechanics has evolved as a design philosophy which can be used to develop fracture-safe designs. It can be also applied in analysis of failures, to ascertain if sound design and fabrication methods have been used."

Jan 1, 1985

By W. Torres Pino, L. Mariscal Samaniego

The Ilo Smelter has been continuously operating since 1960 with Reverberatory furnaces and Pierce Smith converters producing blister copper. The original installed capacity of 1.134 tons per day of concentrated was expanded in 1976. A process of modernization started in 1995 and 1998 with the installation of an El Teniente Converter, a sulfuric acid plant and an oxygen plant to reduce the gaseous emissions to the atmosphere. With the official approval of the Environmental Compliance and Management Program (Programa de Adecuaci6n y Manejo Ambiental - PAMA) in January 1997, Southern Peru Copper Corporation made a commitment to capture 91. 7% of the S02 generated at the smelter by January 2007. After an evaluation of six different technologies, the ISASMEL T process was selected because it can be easily adapted to the present operation, has a lower capital cost and it is a simple process. The fast learning curve to reach the total capacity will allow to fulfill the PAMA commitment in time. The project construction is in process and SPCC is prepared for a successful start-up and transition of the current operations at the end of year 2006. This paper outlines the factors considered by SPCC in its choice of ISASMEL T technology and describes the construction and the start-up activities of the new facilities.

Jan 1, 2007