Search Documents

By M. N. Bassim, W. W. Tennese

"Concepts of linear elastic fracture mechanics were applied to study two cases of failure, namely an equalizing beam from a tandem rear axle of a highway tractor unit and the main beam of a flat bed trailer. In the first case, the presence of a crack, initiated by stress corrosion cracking followed by significant fatigue crack propagation produced a state of stress which was sufficient to produce brittle failure. Calculation of the fatigue life agreed with the number of cycles that the structure experienced before final fracture. In the second case, it was demonstrated that a combination of low temperature and high loading rate was sufficient to cause brittle fracture.IntroductionFailure analysis of engineering components has generally been carried out without the benefit of fracture mechanics. It is generally understood that real structures inevitably contain internal or surface flaws which under an applied load, may propagate to fracture. Fracture mechanics relates the applied stresses to the crack size in specified geometries. Since its introduction approximately thirty years ago, fracture mechanics has evolved as a design philosophy which can be used to develop fracture-safe designs. It can be also applied in analysis of failures, to ascertain if sound design and fabrication methods have been used."

Jan 1, 1985

By D. W. Euler, D. G. Brophey

"In an attempt to address the issue of rising labour costs, and to improve productivity, a laser-based system to guide underground LHDs and trucks has been developed. This comprehensive system is known as the Opti-Trak system.Essentially, the vehicle is equipped with front and rear-mounted lasers which scan a reference strip mounted on the drift back. The vehicle follows this reference strip and in addition, based on reflective bar codes mounted beside the reference strip, initiates certain functions (i.e. dump cycle, speed change, brake check, etc.). Any programming that is drift-specific is handled by the positioning of the reference strips and bar codes. Consequently, the vehicle can easily travel to many different haulageways or branches, providing the reference strip and bar codes are in place.The advantages of this system are an immediate elimination of haulage operator costs and an increase in available hauling time to 7 hours out of an 8-hour shift as compared to the typical 5Y2 out of 8 hours that a manned haulage system offers.This paper describes the Opti-Trak system and the benefits to be realized from automation of mine haulage requirements."

Jan 1, 1994

By D. Schleiss

Reduced access to knowledgeable workers is creating challenges for operations. We are doing more 4D Operations - dirty, dull, dangerous, and distant. Personnel costs in these environments are high, and it is not always possible to get the people where you need them. Integrated Operations is a strategy to integrate people, process, and technology for faster and better decision making. Adopting an integrated operations approach can help to relocate personnel, improve collaboration, and align objectives to deliver reduced costs and improved performance. In this paper, the authors will highlight the required infrastructure to enable an Integrated Operations platform. Key decision points for enabling this technology for both Greenfield projects and existing mines will be discussed. Furthermore, the benefits and improved return on investment that result from deployment of an Integrated Operations strategy will be presented.

Jan 1, 2014

By G. W. Govier

Measurements of the settling rates and the rheological behaviour of heavy media formed of fine suspensions in water of each of magnetite, ferrosilicon, and galena have been made. For media ranging from 1.6 to 2.8 specific gravity the settling measurements gave initial settling rates of from 0.5 to 0.01 ?cm. 'Per minute for magnetite; from 4.0 to 0.8 cm. per minute for galena; and from 35 to 1.6 cm. 'Per minute for ferrosilicon. These measurements indicate the ?relative stability of the suspensions and should be helpful in establishing the useful specific gravity range for each medium. Measurements of the consistency of the media were made with a Fann Model 35 rotational viscometer. Aibnormal or non-Newtonian behaviour was observed in the case of each media, the apparent viscosity being dependent upon the rate of shear or the intensity of motion. Measurements were made over the rate of shear range of 10? to 1,000 reciprocal seconds. The apparent viscosities of the magnetite media ranged from 450 down to 4?0 centipoise at 2.30 specific gravity, and from 2,450 down to 700 centipoise at 2.80 specific gravity. In the case of the galena media, the variation was from 40, through a minimum of 6, to 10 centipoise at 2.20 specific gravity, and from 950, through a minimum of 180, to 450 centipoise at 3.6 specific gravity. The ferrosilicon suspensions exhibited apparent viscosities ranging from 42, through a minimum of 5.6, to 9 centipoise at 1.9 specific gravity, and from 160, though a minimum of 35, to 85 centipoise at 2.8 specific gravity. The dependency of apparent viscosity or consistency upon intensity of motion is considered to be of particular significance in applications of heavy media where the medium is in rapid motion.

Jan 1, 1957

By Peter R. Drummond

THE paper consists of four sections: (1) a discussion of early work; (2) presentation of the results of a chemical investigation of Falcon-bridge nickel-copper blast-furnace matte; (3) application of the results of this investigation to mattes in general; and ( 4) a summary of conclusions. All general discussion will be confined to the fundamental system of ferrous-cuprous sulphides (FeS-Cu2S). Nickel-, lead-, and zinc-bearing mattes will be treated as minor varieties of the parent system. DISCUSSION OF EARLY INVESTIGATIONS Matte investigations may be divided into three classes: first, those treating the sulphides as alloys-theoretical studies of the system FeS-Cu2S, such as those of Hofman (ll)t or Carpenter and Hayward (2); second, chemical research on mattes made under smelter conditions, such as that carried out by Hawley (3) or Avetision ( 4); third, combinations of the . above, such as the investigations of Gibb and Philp (5) or Fulton and Goodner (6). Much research in the first of these classes, including determinations of . freezing points and of data for structure-composition diagrams of the system FeS-Cu2S, was carried out in the period 1890-1910. LeChatelier and Ziegler (1, 13) proved that FeS, when heated alone above its melting point, dissociated in part, and Friedrich ( quoted by Fulton, 6) showed the same for Cu2S. The reactions may be expressed by the following equations: [xFeS yFe + yS (volatilized)+ (x -y)FeS xCu2S )'Cu+ yS ( vohtilized) + (x -)')Cu,S ] Sulphur is lost by volatilization, leaving a melt of metallic iron plus ferrous sulphide in the one case, and of metallic copper plus cuprous sulphide in the other. If the mixed sulphides are heated far above their melting points, there results either an iron-rich matte containing Fe-FeS-Cu2S or a copper-rich matte containing FeS-Cu2S3-Cu, depending on the relative amounts of each sulphide in the mixture.

Jan 1, 1940

By Youjun Tao

Falcon centrifugal gravity separation tests were conducted to study desulfurization and de-ashing performance with different size fractions of a high-sulfur Chinese -0.5mm fine coal in a dense medium. Performance indicators such as combustible recovery, ash and sulfur rejection, and desulfurization efficiency were used to evaluate the separation efficiency. The results show that for -0.5 mm coal particles, all performance indicators except ash rejection are higher for the Falcon concentrator than for flotation. More specifically, for the +0.125 mm size fraction, Falcon centrifugal separation produced better ash and sulfur rejection performance than froth flotation. However, the Falcon concentrator also showed higher combustible recovery but lower ash and sulfur rejection than froth flotation for the -0.125 mm size fraction.

Aug 1, 2013

By Peter Makuvise, Alain M. Bantshi

"The Mazowe Gold Mine is managed by Metallon Gold (Zimbabwe) and is situated in the west-central part of the Harare greenstone belt. Orebodies here generally comprise shear zones which are in-filled with gold-bearing sulphides and quartz. The mineralised zones are up to 1 m in width, have average grades of 4 to 5 g/t, and mostly dip between 10º and 60º to the north.Mazowe Mine is one of the oldest mines in Zimbabwe, and exploration and development in this region dates back to 1890, with over 1.4 million ounces of gold produced to date. Mazowe mine comprises two underground operations, Mazowe and the BSV sections. Ore is processed in a single plant which consists of conventional crushing and milling and carbon-in-leach facility.Baldmin Projects was awarded the contract for the design, construction and commissioning of the 60,000 tonnes per month plant at Mazowe mine in 2014 for the processing of sand and slimes tailings from previous operations at Mazowe mine. The average grade of the tailings is 1.1 g/t. The plant consists of feed preparation, grinding, flotation, thickening of flotation concentrate, and carbon in leach (CIL). A pump station for hydraulic mining of the slimes tailings dam also part of the plant.Key features of the Mazowe sands Plant are described and include:• Hydraulic mining of gold tailings dump.• Feed preparation section that includes a (W x L) 2.4 m wide x 4.8 m trash screen, 250 m3 surge tank, a cluster cyclones with 2 x 500 mm diam. Cyclone.• Comminution circuit designed for a bond work index range of 10-12 kwh/tonne. comminution circuit is constituted with 3 ball mills, 1.83 m diam. X 6.71 m Long, 280 kW.• Flotation circuit comprising rougher bank, scavenger bank and cleaner bank. Rougher Scavenger bank is constituted of 6 x 6m3 flotation cells and 3 x 30 m3 flotation cells and the cleaner is constituted of 3 x 6 m3 flotation cells.• Concentrate Thickening with 6 m diam. Thickener.• Concentrate CIL (carbon in leaching): CIL circuit is comprised of 7 tanks with 2 leach tanks and 5 Carbon in leach."

Jan 1, 2017

By Côme Carbonneau

The ten -year case history of La Société Québécoise d'Exploration Minière (SOQUEM) is reviewed under the headings of the company's raison d'être, objectives, policies, structure and final goal. A brief analysis of its past operations is presented: aborted efforts, findings and developments. A projection is made of the future earnings, in terms of estimated present value, of its three main discoveries - Louvem , Niobec and Selim.

Jan 1, 1978

By Selwyn G. Blaylock

I.-THE HISTORY OF THE SYSTEM TO trace the history of the development of the Co-operative Committee System in The Consolidated Mining and Smelting Company of Canada, Limited, one must look backward about twenty years. In 1915 and 1916, the first years of the W ar to really affect Canadian life, there were sixteen hundred men working in the Trail plant. These men were, on the whole, a splendid body of men and pa trio tic to the core. They were almost one hundred percent organized, ninety-five percent of them be-longing to the Union of the Western Federation of Miners. Most of the tradesmen belonged to their craft unions as well. For example, there were ? local machinist, steel workers', electrician, boiler maker, bricklayer, and carpenter unions. The Company had always maintained an open-shop policy and refused to enforce membership in any union, but recognized the right of every man to belong to unions. The only exceptions have been the I.W.W. and the One Big Union. Both of these organizations have always been fought by the Company. By 1916, membership in the Western Federation being practically 100 per cent, the Company recognized this organization's authority to make agreements, and a wage and hour agreement was drawn up and signed by the Company and the local officials of the Union, and ratified and signed by the Head Office of the Union in Denver, Colorado. This agreement was for the duration of the war.

Jan 1, 1936

By V. A. Ettel

Current practices in electrolytic winning and refining of copper , nickel and zinc are reviewed from the point of view of their respective energy requirements. The electrical energy requirements of these processes are broken down in to the individual components, which belong to two basic categories: (a) thermodynamic energy requirements (G of the desired reaction) : (b) energy losses (anode and cathode polarizations, ohmic drops in the electrolyte and in the cell hardware, energy losses due to unwanted side reactions and electrical shorts). The individual energy components are separately examined for each electrolytic process and the potential for energy saving in these processes is discussed. It is shown that many potential energy-saving measures are uneconomical at the present time, as they increase over-all operating costs. The discussion is focused on those approaches which hold most promise for the future.

Jan 1, 1977

By G. B. Harris

In recent years, increasing attention has been focused on the hydrometallurgical treatment of base metals feeds, especially nickel laterites and polymetallic sulphides. One approach that has received some attention is the use of high?concentration chloride solutions (brines), which are now showing some promise after initial setbacks. Iron is usually the major component in the base metal feed to such processes, and if physical means cannot be used to remove it, then the iron concentration in the pregnant leach solution is always significant. This paper presents some of the background theory on the hydrolysis of iron in high-strength (>3M) chloride brines, and discusses the roles of temperature, solution concentration and free acidity. It is shown that the system is complex, but that crystalline and readily-filterable hematite can be generated, and that the system has a low energy requirement.

Jan 1, 2006

By M. Yamine, R. J. Ring, D. J. Waters

"An experimental program has been carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's acid as an alternative oxidant to pyrolusite in the leaching of uranium ores from the Alligator Rivers region of northern Australia. Batch leaching tests on Ranger, Nabarlek, Koongarra and Jabiluka ores showed that uranium extraction was unaffected by choice of oxidant, but that Caro's acid reduced acid requirements by 15 - 25%. Lime requirements for neutralization of tailings liquors were reduced by 20 - 30%.The batch studies were extended to a four-stage continuous leaching circuit with a capacity of 400 gore h-I. Comparative leaching tests confirmed the reagent savings obtained in the batch tests. Following these encouraging laboratory results, lnterox Chemicals Pty Ltd carried out plant trials using Caro's acid. Reagent savings in the mill were similar to, or better than, those obtained in laboratory test work. The trials also established that Caro's acid has a number of operational advantages over pyrolusite.IntroductionUranium is most commonly extracted from its ores by leaching in sulphuric acid. Simple hexavalent uranium oxides and compounds are readily soluble but uranium in the tetravalent form is insoluble and must be oxidized for dissolution to occur. The most commonly used oxidants have been sodium chlorate and manganese dioxide. They act indirectly by maintaining iron as the ferric ion which oxidizes uranium by a surface electro- chemical reaction. An Fe3+ concentration of about 1 - 2 g L-I is usually considered adequate for the effective dissolution of uraninite(1)."

Jan 1, 1984

By S. Schwartz, T. Bilney

"Over recent years a number of techniques have been developed as part of the AMIRA1 P9 project to represent mathematically or measure directly sub-processes occurring in flotation cells. These include the determination of:•,?a machine parameter (bubble surface area flux, Sb);•,?a froth parameter (froth recovery, Rf );•,?entrainment and drainage parameters (???and d); and•,?an ore floatability parameter (Pi).These flotation parameters allow the plant engineer to develop a model of the flotation circuit that can be used as a powerful tool to diagnose the performance of that circuit. The recently developed JKSimFloat V6 flotation simulator uses these parameters to predict the flotation circuit performance that would arise from changes in operating conditions and circuit configuration.This new flotation technology was applied to the Placer Kanowna Belle Gold Mine in Western Australia. A series of plant surveys, cell characterisation measurements and laboratory batch tests were conducted to determine the flotation circuit model parameters to be used within the JKSimFloat V6 simulatorA thorough flotation circuit analysis was then performed at Kanowna Belle using JKSimFloat V6. The recommendations that were provided by this circuit analysis have resulted in large improvements in the flotation performance at Kanowna Belle. These include a 1.3% increase in flotation gold recovery and a substantial decrease in operating costs. The analysis is still ongoing, however, the benefits already obtained from applying this technology have resulted in a US$1.3 million a year improvement to the mine."

Jan 1, 2005

By H. A. Schnell

"The Phase I Mill at Cluff Lake in northern Saskatchewan was designed to accommodate a very specific high grade uranium ore. As this high grade ore was depleted, construction was undertaken on a new mill circuit (Phase 2) to process a more conventional lower grade ore deposit.The Phase 2 Mill expanded the ore throughput to 800 tonnes per day. The new process employs crushing, grinding, leaching, counter—current decantation, solvent extraction and magnesia yellowcake precipitation and drying to produce a yellowcake concentrate.This paper discusses the process decisions required for this expansion and outlines the new mill circuit. Included is a review of the start up in August, 1984.1.,INTRODUCTION The Cluff Lake Uranium deposit is located 720 kilometers north of Saskatoon in northern Saskatchewan. A high grade deposit was discovered in 1970 with the first production taking place in 1980 after lengthy hearings. The original mill (or Phase 1 Mill) was specifically designed to accommodate this very high grade ore for a very limited plant life.Pilot plant work was carried out in 1981 on the other lower grade ores found in the immediate Cluff Lake area. Feasibility and process selection studies were then undertaken as the Phase 1 mill was nearing its end of life. These studies were completed in March 1983 when approval was given to construct the new Phase 2 mill."

Jan 1, 1985

By A. K. Snelgrove

Introduction ?Concerning the inland commodities, as wel to be drawen from this land (Newfoundland) there is nothing which our East and Northe.rly countries of Europe doe yeelde, but the like also may be made in (ît) as plentifully by time and industry : Namely, rosen, pitch . . . metalls, and many moe. All which the countries will aford, and the soyle is apt to yeelde ... For besides these alreadie recounted and infinite moe, the mountains generally make shew of minerall substance : Iron very common, lead, and somewhere copper. I will not auerre of richer metalls: albeit ... more then hope may be concieued thereof. " - Narrative of Captain Hayes, second-in-command to Sir Humphrey Gilbert's Expedition, IJ83 (From Hakluyt). The investigations set forth in the following pages were made in the field in Newfoundland during the summer of 1927, and later in the laboratories and library of McGill University, and in the library of the Canadian Geological Survey at Ottawa, with the purpose of collating and adding to our knowledge of the geology of an area roughly wedge-shaped in outline, and nearly nine thousand square miles in extent, stretching across the centre of the island of Newfoundland, from the southwest to the northeast coasts. To the description of this district, which contains most of the known mineral occurrences of Newfoundland, the term mineral belt is here introduced.

Jan 1, 1928

By Amauri Garcia, Rodrigo Valenzuela Reyes, Noé Cheung, José Eduardo Spinelli, Leonardo Fernandes Gomes, Rafael Kakitani

"The present research work deals with directional solidification (DS) of both Al-15wt.%Si and Al-15wt.%Si-1.5wt.%Mg alloys and further characterization of the related microstructures. The growth of refined primary Si and refined eutectic is well-known as positive in order to improve mechanical properties of the Al-Si based alloys. Alloying is also an effective method to strengthen the Al-Si based alloys, in which Mg is considered an important alloying element. However, lack of investigation regarding the effects of Mg on microstructure of these alloys is noted. So, in the present research work emphasis is given on both dendritic and eutectic growth being affected by solidification kinetics (V-growth rate and G-thermal gradient) during transient directional solidification. Experimental evolutions of microstructural spacing of both alloys have been determined which becomes possible to understand the effects of Mg coupled with the effects of growth rate on the final microstructural arrangements. A direct comparison of the tensile mechanical properties obtained for the alloys is also performed. It is shown by these correlations that the addition of Mg generally improves the tensile mechanical resistance with a minor decrease in ductility. Furthermore, the Scheil solidification path of the ternary Al-Si-Mg alloy was determined using the computational thermodynamics software Thermo-Calc, resulting in the following sequence of precipitation: Liquid-Si-a (Al)+Si- a(Al)+Si+Mg2Si. This sequence is compared with the experimental microstructure findings.INTRODUCTION Al-Si alloys containing from 4wt.% to 22wt.% Si comprise more than 90% of all Al-based castings. Parts manufactured with these alloys have a wide range of industrial applications due to their excellent castability, crack resistance, good corrosion resistance, good weldability, low density and high strength (Bray, 1976; Zolotorevsky, 2007; Reyes, 2017). Hypereutectic Al-Si alloys are widely used and researched in the automotive and aerospace sectors due to the low coefficient of thermal expansion, resistance at high temperatures, good wear resistance and high strength (Reyes, 2017; Tebib, 2013). Above the equilibrium eutectic composition (~12.5wt.%Si) the amount of primary Si particles becomes significant (Lasa, 2003). In the place of conventional hypoeutectic Al–Si, there is growing interest in hypereutectic Al–Si alloys as a candidate material for the high-quality engines because a higher volume fraction of silicon may bring about superior properties (Matsuura, 2003)"

Jan 1, 2017

By A. Wright, P. Lacombe, R. del Villar, D. Hodouin, C. Sepulveda

"The data acquisition from industrial plants is a fundamental step for process modelling in process optimization, process analysis and automatic control.The introduction, some years ago, of modern distributed control and data acquisition systems in concentrators imposes a new approach in designing experimental schemes for data acquisition campaigns and new criteria for the treatment of the obtained discrete information.This paper presents the methodology applied to sample a zinc flotation circuit at Les Mines Selbaie, Joutel, PQ. Values of 85 process variables were obtained form the Distributed Control and Data Acquisition System (Bailey Network 90) and transferred to the DOS environment. Another 11 variables (flowrates and valve positions) were directly sampled using an IBM-PC compatible computer equipped with a data acquisition card and a signal processing circuit.All variables, under the vector form, were processed in the PC-MATLAB environment to either filter or eliminate the non-linear disturbances and noises, producing useful data for model development. The filtering algorithms are also presented.INTRODUCTIONProcess control does not need to be justified. Whether manual or automatic, any processing plant requires some form of control to accomplish its main objectives: a good quality product and a target throughput. Process control of mineral processing plants has steadily evolved from manual control, where the operator skills and/or experience play an important role, to some level of automatic control, usually considered better, as less human subjectivity is involved, at least when actions have to be taken.The design of these control systems requires the knowledge of the dynamics of the process it is deemed to control. Process modelling is therefore an essential step in the assessment and the design of a control strategy. The choice of model will depend on the available resources and manpower."

Jan 1, 1991

By S. Deonarain, L. S. Schultz

"This paper details the process and methodology followed to rehabilitate a rectangular ventilation shaft, situated in the Free State region of the Witwatersrand Gold Fields in South Africa. The shaft consists of seven compartments where self-mining of the sidewalls had taken place and damage to the decayed steel work in the shaft had taken place, thus limiting access down the shaft. The paper will provide some insight into the successes and challenges encountered during the project and may provide some learnings for future projects of a similar nature. INTRODUCTION The ventilation shaft forms part of the Phakisa Mine, situated in the Welkom area of the Free State province of South Africa, and is located in the Southern part of the Witwatersrand Basin, one of the world’s largest known and richest gold deposits (Figure 1).As is typical in South African gold mines situated in the Witwatersrand basin, the shaft is 1 770 metres deep (below collar). The shaft was sunk during the early 1940’s and comprised a rectangular shape with 7 compartments, used for both rock hoisting and men and material winding, respectively, with a single lift “Mary-Anne” compartment. Early in 2003, the mine decided to change the shaft from a downcast hoisting shaft to an up-cast ventilation shaft. The conveyances, ropes, winders and headgear (head frame) were removed and replaced with a high volume fan delivering 323m³/s of air at a pressure of 4.2Pa on surface. The up-cast velocity in the shaft was 6.5m/s, however this reduced significantly with the scaling of the shaft and the restrictions at shaft bottom. Although Harmony had converted the shaft from a downcast service shaft to an up-cast ventilation shaft some years back, the shaft steel work in the barrel of the shaft was left intact. Over the years, the steelwork in the shaft had decayed (rust and grime) and portions of this steelwork fell down the shaft. Concurrent with the decaying steel work, portions of the shaft lining had collapsed and it was getting progressively worse."

Jan 1, 2019

By Dharmendr Kumar, Pradip, Sivakumar Subramanian, Beena Rai, Venugopal Tammishetti

The separation efficiency in a mineral processing plant is generally assessed and reported in terms of elemental assays constituting the minerals of interest. However, different minerals comprising of same elements behave differently under similar process conditions. Thus, it is imperative to track the mineral composition thank elemental composition of different streams in a processing plant. The availability of automated mineral analyzers such as QEMSCAN and TESCAN in recent times has made it possible. However, due to the high cost and expertise required, their adaptation in day to day monitoring of operations is not yet a common place. X-ray diffraction (XRD) profile fitting (Rietveld Refinement) is another technique which can provide estimates of mineral proportions in a sample. The results of Rietveld Refinement however are affected by coating of fines on coarse particles, method of sample preparation, particle size distribution of sample, elemental substitution in mineral crystal lattice. In the present work, we propose a simple and efficient method for quantitative estimation of minerals in iron ores using elemental assays and thermo-gravimetry analysis data. The minerals (hematite, goethite, gibbsite, kaolin and quartz) are identified using powder XRD analysis. It is also observed that goethite contains Al substitution in the crystal lattice. The samples were analyzed for %Fe, %Al2O3 and %Silica using chemical analysis. The measured Loss on Ignition (LOI) in the sample is contributed from goethite, gibbsite and kaolinite phases. LOI from gibbsite and goethite occur in temperature range 250–350°C and LOI from kaolinite occur in temperature range 400–700°C. According, LOI are determined in two different temperature ranges that are 100–400°C and 400–850°C. We have used the data to successfully determine the mineral compositions of iron ore samples. We have also employed a data reconciliation algorithm on the calculated data for further improvement and consistency of our results. Our method is very convenient for quick estimation of mineral proportions in a sample. The proposed method can also be used for quantitative phase estimation in bauxite ores and red muds.

Jan 1, 2016

The properties required for a com-pound to form useful thermoelectric materials are described. Uranium compounds which might have these properties are reviewed. Several of these compounds have been prepared and fabricated into compacts. The apparatus used for hot pressing, and for the measurement of thermoelectric power, electrical conductivity and thermal conductivity, is described. Detailed attention has been given to the properties of the nitrides. Preliminary studies on a number of other uranium compounds are reported. The figures of merit of the best materials so far examined are one-tenth of those necessary for a useful thermo-electric material. THE efficiency of thermoelectric materials for power generation and cooling is determined by their figure of merit, Z = a2 a/K, where a, a and K are thermoelectric power, electrical conductivity and thermal conductivity, respectively. It is well known that the largest values of Z are achieved with semiconductors (1). High mobility of charge carriers is necessary for simultaneously high thermoelectric power and electrical conductivity.The properties required for a com-pound to form useful thermoelectric materials are described. Uranium compounds which might have these properties are reviewed. Several of these compounds have been prepared and fabricated into compacts. The apparatus used for hot pressing, and for the measurement of thermoelectric power, electrical conductivity and thermal conductivity, is described. Detailed attention has been given to the properties of the nitrides. Preliminary studies on a number of other uranium compounds are reported. The figures of merit of the best materials so far examined are one-tenth of those necessary for a useful thermo-electric material. THE efficiency of thermoelectric materials for power generation and cooling is determined by their figure of merit, Z = a2 a/K, where a, a and K are thermoelectric power, electrical conductivity and thermal conductivity, respectively. It is well known that the largest values of Z are achieved with semiconductors (1). High mobility of charge carriers is necessary for simultaneously high thermoelectric power and electrical conductivity.

Jan 1, 1963