Search Documents

By Lawrence D. Hoy, Armand Savoie, Pierre Trudel, Ghislaln Tourigny, Robert Crépeau, Lao Kheang

"Recent fluid inclusion and stable isotopic studies in the Bousquet mining district have identified spatial and temporal trends in mineralization temperatures and isotopic compositions of vein forming fluids. These studies indicate that mineralizing temperatures were lower during sterile vein formation (T=200-300°C) than during auriferous vein formation (T = 300-400°C), and that 8 80 values of minerals in sterile veins are lower by 1-3 %o than in associated auriferous veins. In addition to these small differences in 8 80 within individual mineralized zones, a trend of increasing 8 80 values of vein minerals is identified from west to east across the district, with 8 80 of vein minerals increasing by4-6%o. Quantitative evaluation of potential causes of the observed oxygen isotopic shifts suggests that the best explanation for these trends is the derivation of the mineralizing fluids from an isotopically inhomogeneous terrain in which the fluid isotopic compositions are controlled by the isotopic compositions of the host lithologies due to high rock/water ratios in these source terrains. This inhomogeneous source terrain is interpreted as consisting of the Blake River Group volcanics (low 8 80 component) and the adjoining Kewagama and Cadillac Group sediments (high 8 80 component).The genesis of the hydrothermal fluids is attributed to crustal heating during metamorphism, with the fluids representing metamorphic dewatering products and/or fluids incorporated during deposition and burial of the host lithologies. Ductile deformation of the fluid source regions impeded fluid migration during metamorphism; the ultimate release of the mineralizing fluids is attributed to the penetration to depth of vertical structures (fault and shear zones) during brittle deformation of the crust under waning metamorphic conditions. Release of fluids caused by this puncturing of the closed hydrologic source regime produced a localized zone of lowered pressure, drawing fluids from adjacent lithologies toward the fault zones, feeding further hydrothermal fluid upwelling. Au mineralization resulted from chemical processes related to cooling of the hydrothermal fluids and/or interaction with lithologies encountered during fluid migration; the level of crust at which Au deposition occurred likely migrated upward with the thermal anomaly caused by hydrothermal fluid upwelling, eventually reaching the level of current exploitation. Cessation of fluid flow along the vertical structures is attributed to inadequate recharge of the hydrothermal systems as fluid contents were depleted in the lithologies proximal to the vertical structures and/or sealing of the structures by mineral deposition."

Jan 1, 1990

By P. J. Lunder, R. C. Pakalnis

This paper presents the results of research that has been undertaken in order to develop an improved method of determining the strength of hard-rock mine pillars. Pillars are found in various shapes and sizes in all underground mining operations. Prudent engineering design requires that if pillars are to perform as desired, both the pillar strength and the pillar stress must be determined. A detailed pillar stability study has been combined with an extensive database of published pillar case histories (178)resulting in a new “hybrid” pillar strength formula, “The Confinement Formula”, that utilizes classic strength of rock methods combined with empirical methods. “The Confinement Formula” utilizes a “mine pillar friction term” calculated from the average minor/major stress ratio with-in the pillar core. Statistically, the new formula provides better results at predicting pillar strength for the combined database than the best empirically ft pillar methods that currently exist. “The Confinement Formula” allows for the determination of the strength of mine pillars with an increased level of confidence over previously applied methods.

Jan 1, 1997

By C. Hunt, J. Vivas, D. M. Allen

"In this paper we present the results of a combined remote sensing - numerical modelling study to improve our understanding of groundwater seepage in open pit and natural rock slopes, and to investigate the interaction between groundwater, in-situ stress conditions and brittle fracture. The location of seepage is a key element in the characterisation of rock slope stability in open pits and natural slopes; definition of the fracture network geometry and its inter-relationship with seepage, however, remains a challenge in engineering practice. Current techniques used to characterize groundwater seepage locations require direct access to the rock slope for a detailed and exhaustive investigation, and can be severely limited due to access and the limited coverage of the survey methods both with respect to the height and length of the sampled rock slope. Herein, we describe remote sensing methods, which allow the collection of structural and seepage information over a wide spatial area. Remote sensing techniques are shown to have the potential to provide additional insights into the orientation and general connectivity of fractures that may play a major role in the general stability of a rock slope. A preliminary methodology for the use of remote sensing in the characterization of seepage zones in a natural slope through the application of ground-based LiDAR and Infrared Thermography (IRT) is presented.One of the most challenging problems in rock slope engineering is the realistic simulation of fluid flow through fractured and deforming rock slopes. Deformation and the development of brittle fractures can cause significant local changes in the permeability and strength of the rock mass, potentially affecting rock slope performance. Understanding fluid flow through fractured and deforming rock slopes, especially in highly-stressed environments is of great importance for slope stability analysis. Changes in the interconnectivity of fractures during slope failure are an important, yet are relatively unstudied in rock slope engineering. We present the results of hydromechanical UDEC-Trigon rock slope models focussing on the potential role of brittle fracture in rock slope failure, its interaction with groundwater pressures, and the influence of the assumed in-situ stress ratio. Damage intensity parameters are used to characterize damage within different regions of a biplanar slope failure."

Jan 1, 2015

By B. K. Ayres

Modern management of uranium mine or mill waste storage facilities (WSFs) often requires that they be remediated or decommissioned with a cover system. In addition to creating a self-sustaining landscape that supports the end land use, cover systems are intended to reduce long-term risks to human and ecological receptors from the stored waste to acceptable levels. The performance and longevity of a cover system will be strongly influenced by the features or shapes of the WSF final landform. Hence, cover systems and landforms must be thought of as an integrated design. Based on the author’s experience, the most important elements of the design process for maximizing the potential of WSF final landforms / cover systems being sustainable over the long term are noted in this manuscript. Several key items that must be considered and addressed during the planning phase of constructing a WSF final landform are also described. Various methods for monitoring performance of a WSF final landform are also reviewed. Key aspects associated with decommissioning a tailings WSF and waste rock pile at the former Cluff Lake uranium mine in northern Saskatchewan are included to illustrate many of the practical insights provided in this paper.

Jan 1, 2020

By L. K. Daneshmend

"Competitive pressures dictate that the mining industry moves to larger mobile underground haulage equipment with more advanced equipment mechanization, higher levels of autonomous operation of machines, and longer periods between access by maintenance personnel. Since such new machines will of necessity be more complex than existing designs, machine reliability has become a key issue in progressing toward advanced mobile underground haulage equipment. Reliability and maintainability models of such equipment are practically non-existent in the literature. This paper addresses the issue of reliability and maintainability of mobile underground haulage equipment on two fronts: reliability modelling to enhance decision making for maintenance planning; and reliability simulation to enable evaluation of more rigorous production planning scenarios. A case study from a gold mine in the Chilean Andes is presented, for which reliability models of mobile underground haulage equipment, specifically load-hauldump vehicles and underground haul trucks, are developed, and a reliability-based simulation implemented. IntroductionMaintenance accounts for 20% to 35% of the overall operating budget for a typical underground operation, and hence represents the largest portion of the mine’s controllable operating costs (Cutifani et al., 1996; Campbell, 1997; Goddard, 1998). This, coupled with the fact that industry today is faced with an ever more complex and demanding marketplace, has led to an increasing interest in methods to reduce maintenance costs.Although significant effort has gone into developing effective maintenance strategies for industry in general, application of these to the"

Jan 1, 2003

By Paul E. Lamoureux

Introduction The Author As the pail of smoke and wartime destruction gradually rises from the surface of the earth, from all countries, statesmen assemble to discuss and prepare pacts and treaties which are designed to, once more, bring people of all nations to understand each other and live in harmony. Scientists and engineers throughout the world are also undergoing a drastic reconversion in their ideas and objectives. No longer do they think only in terms of destruction and twist their brains to develop more devastating weapons or to surpass production records of war machinery. They have turned their eyes and ambitions to more pleasant tasks and are taking stock of wartime developments in materials, fabricating procedures, and equipment, many of which had been carefully shrouded with a veil of secrecy, and are applying their new knowledge to the fabrication or improvement of the tools of peace. The next few years will see the gradual elimination of scores of substitutes and makeshifts, expedients which the constantly changing law of supply and demand' under wartime stress necessitated. The universal search for satisfactory substitutes, however, has resulted in a general awakening of plant engineers to the possibilities of materials with which they were relatively inexperienced, with the result that, in many instances, what was considered a substitution at the outset turned out to be more satisfactory than the original material, and, in reality, can be considered a worthwhile development. Not only have materials been explored, but existing fabricating processes have been reviewed, and others, built around the properties and characteristics of new materials, created.

Jan 1, 1947

By Norman A. Grant

"Location and Transportation FacilitiesTHE BEAVERLODGE area of North Saskatchewan is on the north side of lake Athabasca, 500 air miles northeast of Edmonton.The main Eldorado operation and townsite are on the north •side of Beaverlodge lake, which is immediately north of lake Athabasca and is separated from it by only a mile long portage at Lodge bay. The once famous town of Goldfields. Saskatchewan, and the Box property of the Consolidated Mining and Smelting Company of Canada, Limited, are located on lake Athabasca nine mines from Beaverlodge townsite.Previously, all Eldorado freight was delivered by barge at the Lodge Bay portage, hauled across the portage, and across Beaverlodge lake by small Northern Transportation Company barges, which involved many handlings.In 1952 the port of 'Bushell' was established at Black bay. This is a particularly snug harbour, well protected from the main body of the lake and with good foundations for docking facilities. A Butler building, 300 ft. by 60 ft., and tank farms provide storage at the port. A •road from Bushell to the main Beaverlodge operation, a distance of twelve miles through rugged terrain, was built by the Saskatchewan Government. The cost was shared by the Saskatchewan Government, the Federal Government, and Eldorado and other mining companies.Along this road are located the properties of several enterprising mining companies and near the midpoint lies the ambitious budding town of Uranium. This road has made portaging unnecessary and palletized freight loaded at Waterways, Alta., is now loaded directly on trucks at Bushell and delivered to the point of consumption."

Jan 1, 1953

By Link. Theo A.

Introduction Since the discovery of a major oil pool at Leduc, Alberta, on February 13th, 1947, the long spell of 'oil drought' in Western Canada is now being turned into an oil and gas flood which requires immediate action to obtain the optimum economic benefits. The Woodbend, Section 9, and Okalta extensions of the Leduc field itself have been established; the Redwater pool, lying thirty-seven miles northeast of Edmonton, has been discovered and is being drilled up, and the Imperial Schoepp No. 1 or Golden Spike discovery holds promise of something phenomenal in view of the 500 feet of oil-saturated coral-reef porosity whose areal extent is not known. Imperial Stanolind Barrhead No. 1, northwest of Edmonton, revealed the presence of oil in the Madison, and just recently Gulf N.J. Ellis No. 1, some sixty miles southeast of Leduc, found commercial production in the Leduc D-2 discovery zone. In addition to these Paloeozoic discoveries, gas and oil reserves have also been established in the Upper and Lower Cretaceous, which must be penetrated by all tests on the way through the geological column to the Devonian. If ever there appeared to be an index of 'things to come' in the oil industry, this is it. However, without these recent discoveries the picture in Western Canada does and always did, look very promising indeed. A brief survey of the geological setting in Western Canada is the object of this contribution.

Jan 1, 1949

By A. Todd Davis

"Introduction“CAN YQUR Company afford not to train?"" This question was asked by Jack Taylor in the Factory Management Magazine for June, 1950. Mr. Taylor went on to say, ""No, it can't; no Company can"". It's true that many training programmes have not done the job they were designed to do because of a number of factors such as parts of management resenting training, management failing to understand the abstract values of training, and management giving impossible assignments or picking the wrong trainers. However, Mr. Taylor summarizes his article by saying that a properly-designed and •conducted training programme brings a company or a corporation to the point where the question is: ""Can my Company afford not to train?""About two years ago, in July, 1952, Nevada Mines Division of the Kennecott Copper Corporation embarked on a training programme, the same type of programme that had been inaugurated earlier at the •Utah Copper Division at Bingham, Magna, and Garfield, Utah. President Charles Cox of Kennecott, in •a speech made •before the Utah Bankers Association in June of 1951, stated that, ""I think that our programme of employee training is one of the most important phases of our entire operation"". That statement might be said to be one of the guiding principles of training at Nevada Mines Division. Training is supported by top managements and down the line to Division managements. As the years go by, the Company expects to receive many benefits from training."

Jan 1, 1954

By Marvin E. Lane

Viburnum, located in the foothills of the Ozarks in south-east Missouri, is the site of a modern lead mining and milling operation. Two mines are currently producing a total of 5,000 tons per day and a third mine is in the final development stage, with full production scheduled for late this year (1964). These mines will supply the tonnage required to keep the Viburnum mill operating at a full capacity of 7,000 tons per day for many years. The efficient underground mining operation is completely trackless. Drill jumbos are used to break the ore in a room and pillar method of mining. Transloaders, or St. Joe shovels, and trucks do the loading and hauling. The Viburnum mill has a world-wide reputation as a most efficient operation. This is due to the extensive use of automatic process controls, and labour saving materials handling facilities. Introduction THE St. Joseph Lead Co., has operated lead mines in southeast Missouri for 100 years. These operations have been confined largely to the area called the

Jan 1, 1964

By J. Ita, F. Malekzadeh

"Multi-scale simulation in coupled fluid flow- geomechanical systems is a computationally efficient method for numerically solving large poroelastic systems. When using multi-scale methods, care must be taken in ensuring consistency when information is exchanged between systems that have a different discretization. Here a method is presented which provides consistency between the pore pressure being calculated on a fine scale fluid flow domain and upscaled to the coarser scale geomechanical domain and the pore volume change being calculated on the coarse geomechanical domain and down-scaled to the fine fluid flow domain. Central to this process is the characterization of the mechanical properties of the poroelastic system at both scales.Another advantage of the method presented here is that it is applicable to hydraulically disconnected but laterally drained (i.e. multi-porosity) layered systems as well as hydraulically connected, layered systems. Thus it can be used in geological situations where thin shale streaks or hardpans impede flow between laterally extensive, hydraulically conductive units. This is significant as the pressure evolution of such a hydraulically disconnected, laterally drained system can be very different than a hydraulically connected one as shown here. INTRODUCTIONA multi-scale treatment of fluid flow and deformation is a key enabler when simulation of poroelastic phenomena is limited by computational resources. As the spatial domain of the geomechanics model is usually larger than the fluid flow model, it is desireable to use a coarser discretization in the geomechanical model compared to the fluid-flow model. This type of multi-scale simulation requires a consistent up-scaling of pore pressure from the fine scale fluid flow model to the coarse scale geomechanical model and down-scaling of pore volume change from the geomechanical model to the fluid flow model (see Figure 1)."

Jan 1, 2015

Experimental determination of the response of an AG/SAG mill treating two components of significantly different impact resistance is challenging for two main reasons: firstly, small scale laboratory tests have yet to be confirmed as valid representations of the full scale milling environment, and secondly pilot plant testing requires 10-20 tonnes of ore per scenario which precludes the use of drill core, rendering the process very expensive. In order to mitigate these difficulties, modelling was considered as a potential way forward. However, as the JKSimMet AG/SAG model currently has no capacity to simulate the interaction of two ore types with differing impact resistance, density and/or feed size distributions, an alternative modelling approach was developed. This approach aims to essentially calibrate the AG/SAG process under a set of given conditions, for which survey data and the ore properties of the main components in the feed blend already exist. This paper describes a new conceptual model, which provides a simplified approach for investigating the multi-component behaviour of two ores of differing hardness/SG in a given AG/SAG milling environment, and which can potentially be used for scale-up from laboratory/pilot testwork and geometallurgical estimation of throughput.

Jan 1, 2012

By Paul Staples, Chris Morley

"The development of the Cerro Verde, Amplats Mogalakwena and Boddington projects over the last few years has helped to establish the use of high pressure grinding rolls (HPGR) in comminution circuit designs in large-scale hard-rock applications. The increasing acceptance of this innovative and sometimes controversial technology has had the natural effect of prompting many other new projects to examine HPGR as an alternative to the established, usually SAG-based, comminution circuit design approach.At the current stage of development of the technology, HPGR-based circuit capital costs are generally higher than for the equivalent SAG-based circuit, so that HPGR must offer sufficient operating cost benefits to offset the additional capital costs over an acceptable pay-back period. It is usually necessary to undertake comprehensive project-specific trade-off studies to quantify this effect.This paper describes the processes involved in the execution of a typical SAG-HPGR trade-off study, from the preliminary assessment of ore characteristics and project criteria, through testwork, circuit modelling, equipment selection and cost estimates, to a project-economics comparative assessment of the options. The trade-off study determines both the technical feasibility of the respective technologies and their commercial viability in the given project setting.The paper concludes with a cautionary note to the effect that, while HPGR has many potential benefits, it is not a panacea, and that, for some ore types and project conditions, the more established conventional technologies are often more appropriate."

Jan 1, 2010

By Simon W. Houlding

The mining community is geographically remote and widely dispersed. There is a growing requirement for formalized professional development of members by professional associations, and increasing recognition of the advantages of continuing education and training by both individuals and corporations. Working against these trends are the increasing expense and time commitments required for attendance at conventional courses and workshops. The result is a perceived need for a readily accessible source of continuing education and technical reference on the Internet. The design constraints for an Internet model for professional development include: ? browser compatibility, with any time, any place, any pace accessibility; ? a content presentation model with low bandwidth requirements, appropriate interactivity for examples, tools and reviews, and viewer performance monitoring capabilities; ? formal accreditation of content, presentation and process so that viewer achievements may be formalized in terms of widely recognized Continuing Education Units; ? availability of tools for conversion of source material to the presentation format with minimal effort. A model that meets the design constraints is presented and illustrated by examples from an existing Internet site for continuing education in mining.

May 1, 2002

By R Zavadil, S Kuyucak, F Fazeli

Proton exchange membrane (PEM) fuel cells generate electricity by reacting hydrogen and oxygen. A thin, bipolar electrode material provides a medium for electron exchange with the electrolyte, alternately serving as anode at the hydrogen-rich side and cathode at the oxygen-rich side. Stainless steels have sufficient corrosion resistance to qualify as bipolar plate materials. However, the protective chromite layer increases the contact resistance, the battery’s internal resistance; and thus, decreases the electrical efficiency of the fuel cell. A heat-treatment is proposed and investigated via simulation by ThermoCalc / Dictra and experimentally, to generate a sufficient quantity of conducting surface carbides that breach the protective layer. Once carbide growth is arrested, a subsequent heat-treatment is also needed at a higher temperature to restore the corrosion resistance by filling-in the Cr-depleted layer (sensitization) around the carbide particles.

Jan 1, 2014

By E. O. Chisholm

Synopsis The colour changes effected in a solution of dithizone by trace amounts of copper, lead, and zinc mineralization provide a sensitive field test for these metals. The method has been used with success by the United States Geological Survey to trace zinc orebodies under residual soils. The dithizone test is used here on samples of non-residual soil overlying a gold-bearing zone in which the gold is associated with disseminated sphalerite, galena, and chalco-pyrite. A gold-bearing zone was successfully traced under overburden ranging from a few inches to five feet in depth by means of this method. The method may prove useful in guiding preliminary trenching through light overburden, by outlining the extent of copper, lead, and zinc mineralization. Introduction The dithizone test affords a rapid, simple, and delicate test for the presence of zinc in soil and water and is suitable for use under field conditions. It has recently been used with success by the United States Geological Survey to outline a zinc-rich area in the residual soil over a primary zinc deposit in Tennessee. The purpose of the present study was to ascertain whether the method could be used to trace a gold-bearing zone, containing associated zinc mineralization, under shallow, non-residual, glacial overburden. The results obtained indicate that the method can be used to guide preliminary trenching in overburden up to six feet in depth. Tests made of the water near lake-shore outcrops also indicate that favourable prospecting zones may be located from the water, within five feet of the shore. It is felt that this simple field test should find a wider use in prospecting, because, under certain conditions, it can outline favourable zones and thereby reduce the amount of blind trenching necessary. The following pages describe the type of deposit tested, the method used, the .results obtained, and the difficulties encountered by a novice in the use of this chemical procedure. The author is indebted to the officials of Nor-Penn Mines, Limited, for their co-operation while the tests were being made; to the late Richard Bouska, Kenora prospector, for helpful suggestions; and to F. W. McCamus, University of Toronto undergraduate student, who ably assisted with the work.

Jan 1, 1950

By T. Backers

In fracture mechanics modeling the rock mass is seen as the combination of rock material and fractures, which are evident on different scales. The activation and propagation of fractures dominates the stability and performance issues as well as fluid flow potential. Once fractures have started to grow into each other and create through going separations, stability of rock engineering constructions may be violated. Further, as fracture mechanics inherently incorporated a scaling law in the form of the participating fracture length, scaling issues can be more accurately mirrored. This contribution highlights some examples of application of a fracture mechanics based code on some rock mechanics issues such as numerical laboratory experiments, borehole stability or the creation of fluid pathways due to underground constructions. The results show explicitly the creation of fractures and connection of existing ones, and hence the safety and performance issues. It has to be concluded that the basis for frequent application of fracture mechanics on specialized challenges in Geomechanics is laid, and the needs for future developments are defined.

May 1, 2009

By Deepak Bhadouriya, Saurabh Singh, Aditya Raj Suman

"An experimental study of chemically enhanced filtration and dewatering of fine coal slurry with and without additives was carried out. The experiment involved determination of effect of slurry concentration, additives (cationic, anionic and nonionic), filter area, filtration velocity, particle size and cake resistance on dewatering and filtration using vacuum filtration cell. Finally, the rate of filtration and dewatering and optimum amount of additives used were determined under suitable filtration condition. Overall, it was found that the filtration and dewatering characteristics were enhanced by increased slurry concentration, larger filter area and larger particle size. In addition of additives, the kerosene was found to be best for enhancing the filtration which yielded cake moisture reductions of approximately 17% by weight. At optimum dosages, the final cake moisture contents were reduced by 3.6% and 5.8% by weight using the appropriate surfactant and flocculent, respectively.INTRODUCTIONFor India, it is estimated that coal constitute a principal source of energy for the next several decades. It is majorly used at thermal power plants to generate electricity and also to a great extent in steel and cement industry. It has been observed that its consumption is increasing so as to meet the energy requirements of the country. It has been found that in a coal preparation plant; approximately 20-25 percent coal is of the mined coal of the range below minus 0.5 mm (28 meshes). Generally, this fine fraction is discarded due to its high cost of processing and further utilisatisation is very minimal. But with ongoing research and development for advanced clean coal technology, various new techniques have been evolved to maximize the utilization of available coal. In recent time technologies such as column flotation, cleaning of fine size coal to lower the ash content and low pyretic sulfur is feasible at high recovery value. But in various researches it is found that one of the biggest hurdles in utilization of fine coal cleaning technology by the coal industry is the economic dewatering of the fine clean coal product. Thus, until an economical and practical solution to dewatering of fine clean coal is achieved, the efforts devoted to developing fine clean coal technology will be wasted. In this paper an effort toward enhancing and developing the optimum technique of dewatering and filtration of fine coal slurry has been made."

Jan 1, 2016

By Anil K. Beersing

Effective drainage systems are required for reclamation of mine-disturbed areas to control surface water runoff and avoid excessive erosion. For the conventional structural design approach, armouring material necessary to satisfy the design criteria should not move during the design flood event since displacement would uncover the erodible underlying materials. This paper discusses an alternative geomorphic approach for designing drainage channels and watershed landscape. The approach is based on quantitative studies of geomorphic processes operating in a watershed. A design based on the geomorphic approach replicates the configuration, channel regime, sediment volume and hydrology of natural and mature drainage systems. Movement of some armouring material is acceptable in such an approach because the channels are allowed to mature by natural degradation and aggradation, with erosion rates comparable to the natural environment. The key advantages of a geomorphic approach over a purely structural approach include reduced sizes of armouring material, geomorphologically sustainable landscapes, ?walk-away? or maintenance-free design and reduced liability in the future. The geomorphic approach is illustrated using the example of a coal mining operation in northwest U.S.A. The paper discusses field data collection, design criteria, typical design details, and construction methods.

Apr 1, 2005

By A. Romero

"Most underground mines require heating or cooling systems to meet health and safety standards in the working areas. In regions where daily or seasonal fluctuations of environmental conditions exist, these systems tend to be over-sized and operate at low average load factors, which increase both investment and operating costs. One possible approach to reduce the temperature variations of the fresh air supplied to the mine, and so reducing the investment in large heating or cooling systems, is to use rock as a thermal regenerator or thermal storage system. Packed rock beds act as thermal inertial units, damping the atmospheric temperature oscillations to provide a more constant fresh air temperature. However, although regenerators exist in some mines, and packed bed rocks have been studied in detail in solar thermal power applications, there is a lack of tools to design new and sufficiently large storage systems of this kind. This work fills the existing gap by presenting a methodology to design and evaluate the impact on the ventilation systems of these regenerators. The method is validated using existing rock bed systems found in the literature and illustrates possible designs for small and large size regenerators in both hot and cold climates.1 INTRODUCTION “ It is quite amazing how often answers to extremely complicated problems can be obtained in this way, by using greatly simplified models of the real situation for the purpose of calculation.” Whiller, A. in private communication to J. S. Stachulak (1989). Motivation Most underground mines located in regions with extreme climatic conditions require the thermal pre-treatment of the fresh ventilation airflows, whether for heating or cooling. Heating commonly is needed in sites with sub-zero temperatures and is usually effected by direct or indirect burning of natural gas or propane. Alternatively, cooling is required in areas with hot temperatures, or in mines with high underground thermal loads where the fresh air at ambient temperature cannot provide enough refrigeration. Thus, when the ambient air conditions cannot provide by itself enough thermal power to ensure safe underground working conditions, a heating or cooling plant is required, which involves a considerable equipment and operation cost."

Jan 1, 2019