Search Documents

By G. Stokreef, B. R. Davis, M. Kadiyski, Alvear Montenegro, H-P. Loock, V. Montenegro

An optical probe for burner monitoring in copper flash smelting, first developed at the University of Concepcion, is being industrially tested in a collaboration between Kingston Process Metallurgy, Aurubis AG, and Queen’s University. The sensor uses fibre-optics and optical emission spectroscopy to analyze the light emitted from combusting particles in the furnace reaction shaft. Information that can be extracted from the emission spectrum includes the temperature and brightness of the flame, as well as emission lines or bands from excited atomic and/or molecular species. Laboratory proof of concept testing of the sensor was first completed in a continuously fed drop tube reactor using O2/S stoichiometric ratios between 0.8–4.0. These O2/S stoichiometries capture the industrial operating condition, which is typically less than 1. The results from lab testing justified a plant trial of the optical probe, which was done in the Aurubis Hamburg flash furnace in September 2018. From this trial, approximately 31 hours of spectral data were collected and synchronized with furnace operating data. The results from both drop tower test work and the plant trial are discussed with implications for process monitoring in the commercial furnace. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process. It is used to treat copper sulphide concentrates and small amounts of secondary materials, such as dust generated by the process. O2 enriched air and the concentrate blend are fed into the furnace reaction shaft through the concentrate burner. As the particles fall through the reaction shaft, they heat up and ignite, causing rapid, exothermic reactions that oxidize the iron sulphide, some copper sulphide and impurities in the feed. Reacted particles fall into the settler of the furnace, melt and separate into a matte and slag, while the SO2 enriched off-gas is carried out of the furnace for heat recovery and H2SO4 production. Operation of the furnace is achieved by adjusting a limited number of control variables. The main variables are the blast feed rate, blast oxygen enrichment, SiO2 flux feed rate and CH4 combustion rate (CH4 is used when the chemical energy of the concentrate is low) all measured relative to a set feed throughput. (Davenport & Partelpoeg, 1987; Davenport, King, Schlesinger & Biswas, 2002) The batch tapping nature of flash furnaces makes operation difficult because these control variables impact each other, and product quality can only be measured when matte and slag are tapped from the furnace. This means that operation of a furnace is based on feedback control from matte and slag assays. Because of the time-delay associated with understanding product quality, there is interest in using technology to monitor the combustion reactions that happen in the furnace reaction shaft.

Jan 1, 2019

By R. F. Neider, W. R. Bain

"Expanding upon one aspect of a recent paper on ""Fluid Column Roasting at Sherbrooke Metallurgical Co. Ltd.,"" the present paper deals with the operation of the fluid column process to achieve substantial elimination of cadmium and lead during the roasting of pelletized zinc concentrates. Designed to meet the need for additional feed for Matthiessen and Regeler Zinc Company's vertical retort zinc smelter in West Virginia, without recourse to a sintering operation, the plant is capable of simultaneously attaining very low lead and cadmium levels on demand, through operation in the manner described. Fluidizing air admitted via the wind box is supplemented by natural gas admitted via a tuyere bank 15 ins. above the hearth, in quantities adjusted to maintain a reducing atmosphere within the interstices of the bed. In addition, careful attention is paid to bed temperatures, which run from 1,080° to 1,100°C. Under these reducing conditions, 90 per cent of the cadmium and 92 per cent of the lead in the feed are eliminated, the sulphate sulphur content is decreased by 0.5 per cent, sulphide sulphur is held at 0.6 to 0.08 per cent, and the zinc content correspondingly in-creases. The fuel value of the natural gas is recovered as extra steam, which carries a credit. There are some added difficulties with fume accretions, gas conditioning and gas -cleaning, some of which have yet to be overcome."

Jan 1, 1967

By W. C. Zhu, C. H. Wei, L. L. Niu

With an increase of mining depth, a series of mining-induced hazards such as rockburst, coal and gas outburst, roof collapse, and water burst are getting more serious and more frequent. The intrinsic mechanism responsible for the occurrence of mining-induced hazards is the damage and unstable failure of rockmass or coal seam. The most distinct difference between deep and shallow levels is the so-called three ‘high’ (H3) conditions, i.e. high geo-stress, high fluid pressure and high geo-temperature. Therefore, the response of rock or coal to the deep mining operation is a phenomenon involving thermal (T), hydraulic (H), and mechanical (M) processes. Most importantly, mining excavation may vary the rock stress condition greatly, which may be a key factor to trigger the mining-induced hazards such as rockburst. In this regard, it is of great significance to clarify the damage and failure mechanism of rock and coal under coupled THM conditions, in order to clarify the rock failure mechanism responsible for the occurrence of mining-induced hazards. Thereafter, the mining-induced hazards cannot be predicted with confidence by considering each process independently. Of course, the requirement to include coupling of these processes depends on the specifics of the mining-induced hazards under consideration. For example, the water inrush is considered as a coupled hydro-mechanical (HM) process, in which the unstable failure of rockmass occurs under the combined contribution of geo-stress and water pressure. As for the coal mining at depth, in addition to high geo-stress and gas pressure in coal seam, the high geo-thermal condition that may greatly change the adsorption / desorption of gas and gas flow should be taken into account. Firstly, a general-purpose mathematical model for rock damage and failure process under coupled THM conditions is formulated based on damage mechanics principle, and it is solved by finite element method (FEM). In this model, the deformation and damage of rock, fluid flow and thermal transfer in rock would interact with each other, one process affects and initiation and progress of another. Then, the model is used to predict the mining-induced water outburst, where it is simulated as coupled hydro-mechanical (HM) problems. Based on the numerical simulation, the dimension of water-proof pillar is designed. Finally, the gas drainage from deep coal seam is numerically evaluated, where the coupled coal-gas interaction considering the effect of gas adsorption/desorption, gas flow in coal seam and geo-stress and geotemperature, is comprehensively taken into account. The proposed model could be used for clarifying the mechanism of mining-induced hazards in deep-level mining.

Jan 1, 2015

By John E. Udd

I N Part I of this paper, Professor Morrison suggested that our technique of causing cracks to develop around openings in a sheet of photoe1ashc plastic is, in effect, a laboratory-scale rockburst. Our investigations have indicated that the location and direction of these cracks are predictable, and that their growth can be controlled. On several occasions, we have been able to cause these cracks to propagate sufficiently slowly to be followed, with the naked eye. In practice, the rate of growth, gradual or sudden, would depend upon rock properties. This part of the paper presents an analysis of the stresses surrounding the openings before and after failure and also this author's views on the causes and after-effects of cracking. An attempt is made to correlate the stress patterns with those deter-mined from pure mathematics. Considering that the openings, except for the central enlargement, are long apertures with somewhat rounded corners, they might be compared with elongated ellipses having axes ratios of about 20:1 or with

Jan 1, 1963

By M. Somppi, D. Weirmeir, Z. Yamak

"Milling operations commonly employ activated carbon to capture complexed gold from lixiviants in leaching processes. As the carbon moves through pipes, pumps, vessels, kilns and other processes in the gold leaching circuit, this consumable may experience losses by various mechanisms like attrition, breakage, and rupturing. Whenever possible, capturing the fine gold-bearing carbon portion of this stream could provide value to milling operations at low capital cost and manageable financial risk. Identifying, testing, and validating the successful payback of a low-tech flocculant system is described. However, the work more closely explores a Monte Carlo risk-based methodology for understanding the potential payback of this project at various confidence levels – an approach that many improvement projects can follow where some level of uncertainty exists.INTRODUCTION Gold milling operations commonly employ activated carbon to adsorb gold from solutions. Normal handling causes the carbon particles from this material to abrade, break, rupture to a size that becomes too small for further use in the process. Operations often concentrate on capturing the fine particles because gold is associated with the carbon and this metal content can be a valuable revenue stream for toll processing. However, the small particle sizes become difficult to separate from the process and can ultimately leave the facility in the waste stream. Hence, operations often place a great deal of care in capturing as much fine carbon as possible by a variety of methods including using screens, settling tanks, and chemical methods. Retrofitting a circuit to capture more carbon fines is common but can expose the operation to financial risk. Approaching this potential improvement by leveraging a Monte Carlo methodology can be effective in understanding the risk and the associated payback of a project at various confidence levels. This method provides a strong framework for capital go-no-go decisions and the structure to validate the potential project success before implementation."

Jan 1, 2019

By Zygmunt Kowalczyk

"A theory permitting the determination of expected surface deformations for planned underground exploitation is proposed and discussed in this paper. The relations between surface subsidence and various methods of mining are analyzed, and allowable horizontal .deformations for protected objects, according to the degree of their significance, are reviewed."

Jan 1, 1966

By E. W. Thorton

"This paper is intended to show that grinding media can effect flotation results, and in some instances the results are vastly different. I do not suggest that autogenous grinding is beneficial in the separation of all complex base metal ores, in fact I know of a case where autogenous grinding would be disastrous to any selective flotation. I do however contend that prospective flow sheets and reagent balances of any complex base metal ores should be tried with both types of grinding. I feel fortunate that the paper to be presented later in this meeting by Rene Klymouski will, I think, compliment and perhaps explain some of the results of my research.This paper will be in four parts. The first part deals with a literature survey on the subject. Surprisingly enough, very little information has been printed on the subject. The second part deals with results obtained in bench scale tests on an ore from Chester Mines Limited. It was in these tests that we realized that steel grinding was giving us serious problems. So bench scale tests are shown giving results with a stainless steel grind, a mild steel grind and a grind in a ceramic mill with ceramic billets.The third part of the paper deals with results obtained in the Mines Branch Pilot Plant, when again we ground the ore with three different types of grinding media. Incidentally, this has been the only pilot plant test made at the Mines Branch in which flotation products were made on both steel grinding and autogenous grinding on the same ore. The fourth part deals with two other New Brunswick ores and is intended to show that changing the grinding media effects ores other than that of Chester Mines Limited."

Jan 1, 1973

By O. Schnake, M. Isakson, C. A. Landolt

The paper presents the conceptual basis for the development of an Activity Based Costing system (ABC) for the analysis and estimation of process costs in mining and metallurgy. In particular, it discusses three major thrusts towards attaining increased efficiency in extraction and processing systems: (a) understanding the link between process and expenses, (b) identifying the chemical and physical factors that govern process costs and ( c) using process and cost models of the production systems. The authors have developed computer techniques to analyze data from conventional accounting and apply them to the development of process based ABC systems. The cost causing activities are linked to management units patterned after the organizational structure of the production system. All costs are associated with specific process functions such as charge preparation, smelting, refining, etc. The level of detail is determined by the quality of data available in conventional accounting systems. The system permits data analysis of historical cases and the projection of costs for new production schemes. Results can be presented in various levels of aggregation, following organizational and/or functional structures. The outputs of the system are tabular and graphical, typically following Pareto analysis concepts.

Jan 1, 2007

By Michael Samis

Conventional project valuation techniques, such as discounted cash flow (DCF) method, are more frequently being criticised for the manner in which they consider the interacting effects of uncertainty and project structure (including management flexibility) on project value. Modern asset pricing (MAP; often called ?real options valuation? when applied to the analysis of flexibility) is a more general valuation framework that corrects many of the shortcomings of common valuation methods. Previous mining applications of MAP have tended to treat the ore deposit as a homogenous entity. While useful for demonstration purposes, this is inadequate for practical application in industry. This paper presents a MAP valuation example that allows for the heterogeneous nature of an ore deposit. It shows that deposit structure may increase the complexity of the mine planner?s decision so that results of a standard DCF analysis, or a simple MAP analysis that ignores the details of deposit structure, are misleading. In the example, a management is considering the development of an adjacent low-grade zone while mining operations in a high-grade zone are ongoing. If the low-grade zone is developed before high-grade reserves are exhausted, the proposed development will include both low-grade zone development and a capacity expansion to handle additional low-grade reserve production. If development of these reserves is delayed until the high-grade reserves are depleted, then the low-grade reserves can be developed without a capacity expansion. A typical DCF analysis would reduce the management?s decision problem to three alternatives: 1) continue mining only in the highgrade reserves, 2) immediately develop the low-grade reserves and expand capacity, and 3) delay low-grade zone development until the high-grade reserves are exhausted. The model presented here allows the management to reconsider the development and capacity expansion decision on a discrete half-year basis. It delineates price regions, for given levels of high-grade zone reserves, in which it is optimal to develop the low-grade zone, defer low-grade zone development and abandon the mine irrevocably. The model presented here extends the ability of mine planners to describe actual project structure while using the MAP valuation framework that is already noted for its capacity to combine project uncertainty and risk insights with a dynamic project description.

May 1, 2001

By Mel Owen, Bob Tipman

"A number of studies have identified the presence of heavy minerals in the Athabasca oil sands. A 1996 Mineral Development Agreement study into the recovery of Co-Products identified low operating costs, a simple flowsheet and access to market as key drivers in advancing interest in a viable project.Commercial bitumen extraction processes recover 50% of the titanium heavy minerals and 85% of the zircon into froth containing 1 % of the feed solids. Froth treatment tailings grade is 11.5% Ti02 and 3.6% Zr02.Processing this high grade feed in a combination of flotation, roasting, screening, gravity concentration and magnetic separation, results in concentrates of rutile, leucoxene, ilmenite, zircon and rare earths of marketable quality.A combination of high grade feed and a simple process lead to operating costs among the lowest in the industry. Low cost heavy minerals and low energy costs indicate an intriguing potential for low cost pigment production in Alberta. The production of heavy minerals from oil sands remains one of the largest untapped resources in the Province of Alberta1.0 IntroductionThis paper describes the results of an investigation into the recovery of heavy minerals from tailings produced by the major oil sands plants. The study was carried out under a Canada-Alberta Mineral Development Agreement (Alberta Chamber of Resources 1996). The MDA Co-Products Study examined the potential for the economic recovery of heavy minerals from oil sands tailings."

Jan 1, 1998

By H. W. Leon, F. J. Ellis

"This paper covers the new six-strand curved-mould billet casting machine at the Contrecoeur Works of SidbecDosco. It commenced production of 3 Yz-in. square billets at the beginning of January 1972. Together with two 100- ton ultra-high-power electric furnaces in a new meltshop, it is the principal source of billets for the existing rod and bar mill also located at Contrecoeur. The paper develops the reasoning for casting-to-size 3Y2 -in. billets and for choosing a six-strand machine. It indicates the significance of Sidbec-Dosco Montreal Works' extensive experience in operating a four-strand curvedmould billet machine since 1965 and the ways in which this experience influenced the design and operation of the new caster. Machine features are described in detail, as are the reasons for some of the features. The installation, checkout and crew training are briefly discussed as well as the tundish teeming trials. The first cast on January 5, 1972, is covered and a log is shown of the first casts to an empty ladle. There are operating statistics covering the first 100 casts, which produced 8000 tons of good billets in ten weeks of operation. Machine performance and billet quality were good and the few minor problems encountered are described."

Jan 1, 1973

By A. Abadías Llamas, N. Bartie, M. Stelter

Evaluating the economic viability as well as the sustainability of the Circular Economy (CE) system requires a deep understanding of the distribution of all elements, compounds, alloys, materials etc. in flows. In this paper, the circularity of the copper value chain, including primary and secondary processing, is rigorously evaluated. The studied system comprises the metallic copper production from primary sources (from mineral to metal), copper-containing commodity production (copper is mixed with other metals) and copper recycling through secondary smelting to close the loop. This is linked to photovoltaic (PV) panels and battery storage. A simulation model of this system is created using HSC Sim, considering more than 30 elements (and its various compounds), 180 unit operations and 800 flows. From the mass and energy balances obtained through the simulation, an exergy analysis is conducted to evaluate the resource consumption from a second law (entropy) perspective. Additionally, these results are complemented through a Life Cycle Assessment (LCA), the recovery of technology elements and by-products is discussed, while quantifying the losses through the value chain. Through the digitalization of the complete system, a better CAPEX and OPEX understanding of the metal recovery and losses can be obtained, as well as the associated resource consumption and environmental impacts. New flowsheets and technologies can be evaluated. Several scenarios show how the resource consumption and the environmental impacts are affected by the recovery of different materials to produce different products. INTRODUCTION A key challenge of the circular economy (CE) is the linkage and optimization of both resource and energy efficiency of the (renewable) energy infrastructure and the resource cycle depicted by Figure 1 simultaneously. In addition, the CE requires the linkage of all stakeholders as shown by Figure 1. This has been discussed in some detail by Reuter and Bartie (2019) and Reuter et al. (2019). Copper and all its associated technology elements is one of the key enabling metals that is an economical copper colored thread through CE society (Reuter & Kojo, 2014). The Metal Wheel (Figure 2) shows the linkage of and recovery of various elements associated with copper and other carrier metals. This reveals that copper acts as an important carrier metal because of its properties i.e. the wealth of technology elements it carries from geological ores, but also its capacity to act as solvent of valuable elements and thence a key closer of various complexly connected element and material cycles when these technology elements are released during copper refining. The same applies to all other carrier metals of modern CE society as shown for example recently in a lead policy brief (Blanpain, Reuter & Malfliet, 2019).

Jan 1, 2019

By A. Akerman, C. P. O’Connor, N. Vayenas

"Stereolithography is a well-known rapid prototyping technique in the manufacturing sector. Essentially, it is a three-dimensional printing process that produces plastic prototype parts from standard CAD files. At present, Canadian mining companies are not fully aware of the potential of rapid prototyping techniques (RPTs) for their production and mine design systems. Mining engineers and geologists attempt to visualize and understand the characteristics and layouts of orebodies on computer models, and in cases where it is decided to develop physical models, the process is time-consuming, based on simplified constructions. RPTs, such as stereolithography, can facilitate engineers and geologists to quickly, and with satisfactory accuracy, visualize sections of orebodies and evaluate alternative ore extraction techniques using 3D solid models.The research discussed in this paper is carried out by the Laurentian University Mining Automation Laboratory (LUMAL) in collaboration with Inco Limited and the Integrated Manufacturing Technologies Institute (IMTI) of the National Research Council of Canada. The main objective with this research is to evaluate the applicability of state-of-the-art RPTs to underground hard rock mining systems. RPTs can play a significant role in accelerating the design and development process of mining systems."

Jan 1, 2006

By F. McGravie, S. T. Solinski, W. W. Robertson

During this, the Centennial year of the discovery of the Hall-Heroult process, it seems appropriate to review some of the developments which have taken place in Canada and to explain why it has become an important world centre for the production of primary aluminum. For many years after it was recognized that the element aluminum existed, scientists were frustrated in their efforts to isolate it. In the early 1800s H. C. Oersted and Frederick Woehler prepared small quantities sufficient to measure some of the physical properties. A quasi-commercial process involving reduction with metallic sodium was developed by the French scientist H. St. Claire Deville in 1855 but the cost was very high ($30. 00 per kg). It was not until 1886 that Charles Martin Hall in the United States and P.L.T. Heroult in France, more or less simultaneously but completely independently, discovered the process which is essentially that in use today. Some of the early pioneers in the industry quickly recognized the potential of the hydro-electric resources in Canada as economic energy suppliers for aluminum production. The first commercial production in Canada was in Shawinigan, Quebec in 1901, only 15 years after the process was discovered. Subsequently operating plants were established at nine different locations in Canada (Quebec and British Columbia) (Table 1). Operations continue today in all locations except one (La Tuque). The table shows present plant capacity which for the older plants was reached in an evolutionary manner including replacement of obsolete capacity or upgrading and modernization of existing designs.

Jan 1, 1999

By Mario E. Rossi

The full economic evaluation of a mining project requires a block model that provides an estimate of the tons and grades of available resources. The model must be representative of the mineralization to be found at the time of mining for specified extraction periods and within acceptable error margins. In an operating mine, there may be a reasonable understanding and estimates of actual dilution and ore loss. This paper discusses the issue from the perspective of a project at a feasibility or preproduction level of development. Three types of dilution are discussed. Internal dilution (or change of support) is function of the spatial distribution of the mineralization and its relation to the operation?s selectivity. Geologic contact dilution is the unavoidable mixture at contacts or boundaries of material with different geologic characteristics, grades, or metallurgical performance. Operational planned and unplanned dilution should also be considered, sometimes incorporated by factoring the resource model, but more accurately by mimicking the grade control process. The resource estimation process always carries uncertainty, which is sometimes significant, and usually caused by several factors. These include quantity and quality of drill hole information; quantity and quality of geologic data; grade estimation methodology; dilution and mining recovery factors applied; etc. A key decision is to whether estimate as accurately as possible the in-situ geologic resource or to estimate the tons and grade of the material to be fed to the processing plant. The geologic modeling and grade estimation methods used are conditioned by this decision.

May 1, 2009

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (300 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 130 machine-years of operation at locations in North America and Europe. ST has also installed separators for the beneficiation of industrial minerals in North America and Europe. The technology has been successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, barite, and potash.

Aug 1, 2013

By R. W. Schutz

"Titanium possesses an exceptional and wide-range resistance to chlorides and their compounds when compared to most corrosion-resistant engineering alloys (CRAs) used in the chemical process industry. This natural resistance to chlorides stems from titanium’s protective, tenacious, and readily rehealable titanium oxide surface film, which is chemically stable over a wide range of pH and redox potentials in aqueous environments. This passive film explains titanium’s elevated resistance to anodic pitting, crevice and stress corrosion, and erosion-corrosion in aqueous chloride environments.Guidelines for successful selection and application of industrial titanium alloys are derived from an extensive laboratory test database and more than forty years of industrial/chemical service experience. These guidelines are simplified, and alloy corrosion performance is assessed with respect to four basic aqueous chloride service categories where selection or consideration of titanium is highly merited. An overview of historical titanium alloy applications in chloride-rich environments in a wide variety of process industries substantiates their exceptional chloride tolerance. These industrial titanium alloys are cost-competitive with stainless steels and nickel alloys, readily commercially available, and routinely fabricated and welded in the shop and field via well-established methods."

Jan 1, 2002

By A. Supomo, H. Resendiz, C. Burbidge

"Freeport-McMoRan Inc. (FMI) commissioned the expansion of the Morenci Metcalf concentrator in 2014. The concentrator included many design and equipment innovations, including the first-of-its-kind Metso Hydraulic Roll Crusher (HRC), variable speed ball mills and variable speed crushers. In addition to the innovative design, FMI commissioned the Metso APC team to design a realistic process simulator and the plant APC. The process simulator was utilized to train operators before commissioning, which led to a smoother plant start up. The plant APC utilized the concept of dynamic constraint control, which controls the feed to the primary ball mills by “pulling” the tons from crushed rock storage bins, which then automatically are filled by the upstream HRC and secondary crushing circuits. The primary ball-mill control also adjusts the water addition to the cyclone clusters to avoid overload and achieve sufficient grind size. The constraints include in-circuit constraints for feeder capacity, screen-deck capacity, ball mill power, cyclone mass flow, pump capacity and pump motor capacity. The APC system was implemented shortly after the start of commissioning and immediately demonstrated increased throughput and an ability to highlight and quantify process constraints and bottlenecks. The following paper outlines the control strategy, discusses system implementation, results and challenges.INTRODUCTION The FMI Metcalf Concentrator is located in Morenci Arizona on the site of the old original Concentrator. The new Metcalf concentrator started operation in May of 2014. This plant was designed for an average of 63,500 tpd (70,000 stpd), increasing the total Morenci concentrator complex production to a nominal 113,400 tpd (125,000 stpd). The process flow diagram is shown below in Figure 1.The process consists of primary crushing feeding a coarse ore stockpile followed by secondary crushing operating in closed circuit with vibrating screen decks. The screen undersize feeds the first of its kind Metso hydraulic roll crusher (HRC) operating in a closed circuit with vibrating screens. The primary crusher is a Metso 60x110 gyratory crusher. Secondary crushers are Metso MP1250 Crushers with variable speed drives. Secondary crusher discharge is recycled to the dry screen feed bin and screened with oversize returning to secondary crushing and undersize feeding the Metso HRC3000. The product from the 3.0 meter X 2.0 meter roll crusher is wet screened with the undersize feeding the grinding circuit, which is comprised of two each 24-foot diameter by 40- foot-long variable speed ball mills running in parallel with each in closed circuit with a cyclone bank of 12 cyclones. The wet screen oversize is recycled to the HRC feed bin."

Jan 1, 2019

By J. Shibata, N. Murayama

"Rare earth elements are present in more than 100 minerals, of which monazite, bastnaesite and xenotime are typical. Rare earth elements have excellent chemical and physical properties for industrial use in functional materials such as phosphors, magnets, electronic components, abrasives and catalysts. China produces more than 90 % of the world’s rare earths, and Chinese trends significantly influence the demand and price of rare earths. From the viewpoint of resource securement, it is desirable to separate and recover rare earth elements from low-grade resources and wastes. Phosphate gypsum, which is a by-product of wet phosphoric acid manufacturing, contains low concentrations of rare earth elements. In this research, the separation and recovery of rare earth elements from phosphate gypsum were investigated. A series of recovery methods including washing of phosphate gypsum, leaching of the rare earth elements with sulfuric acid, adsorption and desorption of rare earth elements by using ion-exchange resin, and precipitation of rare earth oxalates were carried out. The separation of rare earth elements from Ca2+ simultaneously leached from phosphate gypsum was also investigated."

Jan 1, 2014

By M. Pekguleryuz, S. A. Argyropoulos

"The recovery of additions in light metals is an important parameter influencing consistency of the finished product, which ultimately means cost. Recovery is a function of many parameters such as assimilation speed, addition density, addition practice, liquid metal processing conditions, etc. In liquid metal processing operations, it is desirable to have the maximum possible recovery at the shortest possible time.In this paper a new index will be presented, namely, the rate of recovery (RR). This index quantifies the addition recovery and introduces the time dimension in the recovery increase. As such, the RR equips the liquid metal practitioner with an accurate picture of addition assimilation in liquid metals. Results will be presented on how this index is applied to a variety of additions in liquid aluminum. IntroductionThe data on addition assimilation kinetics offer a valuable parameter describing how fast a given addition enters the metal bath. These data may be expressed as gr m-2 s-1 of additive for a set of experimental conditions which might include bath temperature and degree of bath agitation among others. However, the liquid metal processing practitioner is more interested in the recovery of additions. In other words, the point of interest is the percentage of the used addition entering the metal bath. Ideally, the addition recovery can reach the 100% level. However, in practice, the addition recovery never or rarely reaches that level. Many factors can contribute to this. Some of these factors can be slow assimilation kinetics, addition density, addition practice, turbulence of the melt, etc. In some cases, sloppy addition practices can contribute to low recoveries, or even worse, to erratic recoveries.In this paper a new parameter is introduced. This parameter relates the maximum addition recovery observed over the time needed to achieve this maximum recovery."

Jan 1, 2002