Search Documents

By B. Dubreuil, J. -M. Lalancette, D. Lemieux

A gold bearing pyrite concentrate was treated at the pilot scale for the extraction of gold. Mineralogical analysis of the concentrates identified gold to be mainly present in the form of a solid solution in pyrite. Gold distribution resulted in a poor extraction yield of 55 % by direct cyanidation. A piloting campaign including an oxidative pre-treatment by roasting in a fluid bed was followed by treatment with halogens for gold extraction and has led to a gold extraction yield of 94%. Sulphur removal during the oxidation was very efficient at >99.5% and gold extraction by the halogens was completed within a 1 hour contact time. The piloting was performed on a 300 kg sample and used a diluted solution of hypohalites as the oxidizing agent for gold extraction. Sulphuric acid was injected in the reactor during the halogens treatment to lower pH to 2. The diluted solution of hypohalites (1-3%) was generated by electrolysis during the piloting campaign in a diaphragm-less electrolysis cell. The extracted gold was recovered via adsorption over silica and the gold depleted brine was treated for impurities removal. This brine was recycled for further gold extraction. With the recycling of water and brine, the regeneration of hypohalites and with a barren solid that is inert and stable, the Nichromet Extraction technology is a green process where the protection of the environment does not preclude profitability.

Jan 1, 2014

By Nathan P. Schmidt

Climate and hydrology data are required during all phases of mining projects, including impact assessment, mine planning and design, operational water management and mine closure and reclamation design. In the Canadian north, data sources are spatially sparse and often short-term in nature, and design parameters are often estimated based on data collected at sites far distant. Confidence in such data can be increased by verification or modification using data collected during properly implemented baseline and operational monitoring programs. A data set that accurately reflects conditions at the project is more readily accepted by regulatory agencies during the permitting process, and allows development of more effective and economic water management, mitigation measures and compensation. Data requirements and collection methods for developing an adequate data set for mine development are reviewed. These are illustrated using examples from oil sands, diamond and metal mines in the Canadian north.

May 1, 2004

By M. E. Holuszko

Although there is no widely accepted rigorous definition of handleability, the handling coal characteristics often referred to as handleability define whether a coal has the ability to flow unhindered through the processing and transportation systems. The handleability may be severely affected if fine coal particles tend to aggregate. In the pelletization process, the rolling action of the drum is applied to bring the individual particles into proximity with each other so that they can aggregate and form pellets. Because of apparent similarities between these two processes, the pelletization tests are carried out in parallel to the handleability tests in this project, and the pelletization results are used to explain coal handleability properties.

Jan 1, 2004

By Bob A. Hamaguchi

The Trojan Tailings Pond at Highland Valley Copper developed in only 15 years from a biologically inactive water body into a productive lake with a well established aquatic ecosystem. This process was assisted by a few simple and inexpensive procedures including fertilization and introduction of essential organisms. The success at the Trojan Pond has encouraged the use of similar techniques in other water bodies on the mine site. This paper details: ??The history, water quality and thermal behavior of Trojan Tailings Pond ?Techniques used in fertilization; introduction of micro-flora (algae etc.), large aquatic plants, zooplankton and invertebrates ??Selection and sources of suitable transplant materials ??Rate and extent of vegetation establishment ??Biomass production ??Rates of organic sediment accumulation over tailings ??Bacterial activity in the sediments ??Improved water quality through the bioaccumulation of aqueous metals in plants and the subsequent bacterial binding or precipitation of that metal during decomposition in the tailings sediment. Robert A. Hamaguchi graduated with a Mining Diploma from the British Columbia Institute of Technology in 1971, followed with a Bachelor of Applied Science in Mineral Engineering from the University of British Columbia in 1975. Since graduation, he has worked for numerous open pit mining operations throughout British Columbia. In 1991, he joined Highland Valley Copper working as an Environmental Engineer responsible for government liaison, reclamation, decommissioning and other environmental duties. Heather M. Larratt graduated from the University of Calgary in 1978 with a B.Sc. in Environmental Biology (First Class Honors). She has provided drinking water management and reservoir design for numerous cities and irrigation districts in British Columbia for 20 years. Heather has also worked for 12 years in reclamation of mine water, including passive SRB water treatment systems. Mark R. Freberg joined Highland Valley Copper in 1991 after working at number of mining operations in British Columbia and the Northwest Territories. He graduated in 1979 with a Bachelor of Applied Science degree in Mineral Engineering from the University of British Columbia.

May 1, 2001

Safe underground mine backfilling with hydraulic fill requires efficient fill drainage and stable fill retaining walls or bulkheads. If any or both the above two requirements are not satisfied, such a backfilling operation creates unsafe conditions and may lead to backfill retaining wall failures. Mine backfill retaining wall failures are always associated with economic losses, fatalities and interruption to mine production. Mining industry wants to either reduce or eliminate these fill retaining wall failures. The fill retaining wall failures could be effectively avoided through the use of fibre reinforced shotcrete fill retaining walls and engineered drainage systems through the retaining walls. This paper presents the experience of the author in developing, implementing, and monitoring several hundred fibre reinforced shotcrete fill retaining walls at a mine in Australia with the highest safety standard. The details on the mine backfill drainage system and fibre reinforced shotcrete fill retaining wall designs are also presented.

May 1, 2007

"Dry crushing trials at pilot scale have shown that the IMPTEC Super-fine Crusher has the capacity to generate ultra-fine products from hard mineral assemblages presenting at either coarse or fine feed sizes. The super-fine crusher was introduced at the 27th International Mineral Processing Congress in Santiago Chile, with results from a range of duties, which demonstrated the crusher’s potentially expansive operating scope. This paper focuses on current preparations to progress the technology from pilot scale to commercial scale within a concrete production plant, where lead blast furnace slag will be crushed to ultrafine sizes to generate an active silica product for use as a supplementary cementitious material, which can replace Ordinary Portland Cement. A key objective of the operation is to demonstrate an economical route to reducing the cost of concrete production, improving concrete quality and reducing greenhouse gas emissions. The paper also highlights the potentially key contribution super-fine crushing can make to the long-term viability of iron ore beneficiation by simplifying comminution flow-sheets and reducing operating costs. There is every indication that the technology has the potential to feature universally in metalliferous and industrial mineral flow-sheets. INTRODUCTIONToday’s IMPTEC super-fine crusher is the successful end product of development work over 19 years and is the third particle size reduction device conceived, built and tested over that time. The concept evolved as engineering design progressively developed a mechanism capable of harnessing a highly efficient combination of fundamental particle breakage mechanisms. Early development trials at pilot scale indicated that super-fine crushing had the potential to establish a wet or dry, media free, low energy route to ultra- fine products from hard mineral assemblages. Having achieved some impressive results from open circuit pilot tests on fly ash and granulated blast furnace slag it became clear that the cement industry may well provide opportunities to apply the technology commercially. Following expressions of interest from local cement and concrete plant operators, IMPTEC negotiated an agreement to undertake commercial trials with a SFC 350 super-fine crusher installed on site at a concrete supply plant in South Australia. Super-fine crushing scope was recently expanded following further expressions of interest from research groups involved in the processing of iron ores. Pilot trials are progressing in these areas."

Jan 1, 2016

By Ray Holmes

This paper describes one approach in our search for greater stope efficiency and lower costs. The uppers technique with wagon drills in cut-and-fill stopes was commenced, on an experimental basis, in our Sudbury mines in 1961. To date, the method has developed into an accept-ed production operation. This technique minimizes the intermittent aspects of the drilling, blasting, mucking and filling operations associated with other cut-and-fill methods. However, studies show that not all cut-and-fill stopes are suitable for uppers, the governing factors being ore width, dip of the orebody, and ground conditions where large areas of unsupported back remain stable for ex-tended periods of time until rockbolting can be accomplished. Introduction F ALCONBRIDGE Nickel Mines Limited operates seven mines within a radius of 30 miles of the city of Sudbury, Ontario. These mines extend in depth from 1,500 to 6,300 ft. The ore consists of brecciated, massive and disseminated sulphides, and the ore minerals consist primarily of pentlandite, pyrrhotite and chalcopyrite. Widths are generally irregular and vary up to 150 ft. The ore dips at between 35 and 90 degrees.

Jan 1, 1965

By M. S. Badollet

Introduction The manufacture of some asbestos products involves the use of asbestos in combination with water, cement and granular fillers. This type of production is often called the wet or semi-wet process and requires the use of either pressure or vacuum to eliminate the excess water in the fibrous blend so that the product may develop the proper strength during the curing stage. Asbestos - cement products available today are numerous and are a valuable contribution to the building industry. Their production in quantity depends upon the type of equipment employed, the speed at which it can be operated, and the factors involving the? blending of asbestos, cement, water, and fillers. Assuming that all mechanical troubles at a plant have been eliminated or are under control it is still advisable to study the basic properties of the raw materials used in the asbestos-cement products. The type of cement used is an important factor, but usually the manufacturer of the cement is willing to work with the asbestos development engineer and recommend the proper type to be used for the product. The source of the water should not be overlooked as a general factor involved in the production cycle. Waters containing a high percentage of contamination such as silts, humus, or soluble salts may adversely affect the setting of the cement or cause a slowing down of the production rate in the factory. Asbestos in combination with cement is an ideal material fo1 building products. It is inorganic, will not deteriorate, and can be handled by mechanical equipment with a minimum reduction of fibre length. The many physical properties peculiar to asbestos fibres should be well understood by the manufacturer. They may be briefly enumerated as follows: fibre strength, fibre composition, sliminess, length, harshness, softness, and filterability or porosity. This last named property is important and it is the purpose of this paper to present some basic studies on filtration as applied to production problems.

Jan 1, 1949

By T. H. Wilson

In 1901, the Crow's Nest Pass Coal Company, Limited, began producing industrial coke in 212 beehive ovens at Michel colliery. By 1908, 486 ovens had been installed and in that year 147,623 tons of coke were produced. Coke manufacture has been continuous from 1901 until the present time (1946), with total production of 2,795,402 tons. At present writing, only 100 beehive ovens are operating and production is reduced to 1,800 tons per month, due to the shortage of suitable labour. These ovens are drawn by hand, on contract, and the workmen are exposed to considerable heat. A man draws three ovens in eight hours, thereby producing approximately 1072 tons of coke per day. In addition to the inefficient and costly method of drawing coke in beehive ovens, tremendous losses are experienced in the wastage of gas and tar, which are driven off into the atmosphere. Also, the yield of coke per ton of coal fed to the ovens is low as part 9f the carbon is utilized in producing heat to carbonize the remainder of the coal. A recovery of only 55 per cent of the carbon, as coke, is obtained. The coking process takes place from the top of the charge, which is 21/2 feet deep, downward to the floor. Six and a half tons of coal are charged and 3.6 tons of coke are drawn from the oven after 72 hours' carbonization. The beehive ovens using Michel coal produce a very hard and tough coke, large in size and of silvery appearance, which has served the requirements of both foundry and smelter for many years. In 1938, the Company made a careful study of coking processes with a view to introducing a more economical method than beehive ovens and one that would be less dependent on skilled labour, the supply of which was rapidly diminishing at that time. Various methods of by-product coking were investigated, and it was decided that the Curran-Knowles process offered the greatest possibilities because of the low capital investment in relation to output and also because the horizontal oven design was suitable for an expanding coal. Consequently, a test on Michel B seam coal, supervised by Mr. E. Burrough, of the Fuel Research Department, Ottawa, was run in the Curran-Knowles plant at West Frankfurt, III. The results of this test led to the construction of a ten-oven battery of 32 ft. 6 in. by 8 ft. 3 in. Curran-Knowles ovens at Michel, which were completed in November, 1939. This battery was built as an experimental unit, with provision for an additional ten ovens if the coke proved satisfactory for the market. In 1942, an expanding coke market led to the construction of a second battery of ten ovens, which were completed in April, 1943.

Jan 1, 1947

By G. G. Richards, Y. Oyediran, V. Chow

The oxygen softening process for partial removal of arsenic and antimony from lead bullion has been in use at Teck Cominco's Trail smelter since 1986. In this process, industrial oxygen is injected into bullion to remove As and Sb with the formation of an oxide slag. In Trail, the levels of these elements are reduced to concentrations suitable for processing in the Betts electrorefining plant. Recent moves toward the treatment of higher arsenic-bearing feeds have necessitated an increase in the process capacity to meet the specifications for drossing plant bullion. Process intensification trials were conducted in-plant to develop an operating strategy for higher bullion processing rates. This was preceded by a study conducted with McGill University to develop a fundamental understanding of the therm ochemistry and kinetics of the process. The results have yielded more effective control of the operation, and identified opportunities for further improvements.

Jan 1, 2008

By S. Gregory

Many gold treatment plants have sulphides and coarse particle gangue components that contain gold in their tailings (cyanide leach residues and flotation tailings). Coarse and very fine liberated gold may also be present in some tailings streams. Two issues usually govern the economics of recovering additional gold from gold occluded in sulphide and gangue particles. The liberation characteristics of the gold in the sulphide and coarse gangue (gold liberation versus grind size) is the first and most important of the two. If fine grinding can liberate a reasonable amount of the gold, then the next important issue is how effectively these two constituents can be concentrated. Flotation will achieve high sulphide recovery but is usually costly. Selectivity is also an issue because of entrainment. Continuous centrifugal gravity concentration offers a viable solution to the recovery of both sulphides and coarse gangue however selectivity is also likely to be a problem. The possibility of improving concentrate grade by using a Falcon B separator was investigated. This paper describes a program of test work carried out on a gold leach tailings using a laboratory Falcon '13' separator. The program involved three different bowl angles: 10, 12 and 14 degrees and two bowl speeds (giving 250 and 350G accelerations). A number of tests were also performed on samples that had free gold present to ascertain the size-by-size recovery of gold in these samples.

Jan 1, 2005

By M. J. Scoble, H. L. Francis, D. F. Salter, G. R. Baiden

Intelligent ore delineation refers to the ability reliably to characterize the geological setting of a mineralized body and its grade distribution. This necessitates using all available geological information in a timely and efficient manner, such that effective geological control is achieved. The importance of geological control is paramount to improving the efficiency and competitiveness of underground mines. As a result, the development of new geosensing tools designed to provide more reliable and timely information should be a priority. However, as the sensing tools advance then so, too, must the decision support system in order to allow the full benefits of these tools to be achieved. One potential system considered able to provide this architecture is ’true 3D-GIS’ (Geographical Information System). GIS promises to provide a seamless data flow and to connect information currently unavailable to the underground mine operations by bringing together previously disparate and spatial data sets in a visually effective and timely way. This paper considers the potential revolution GIS offers over the flow and use of data in mining by focusing on the integration of geosensing data and GIS to facilitate intelligent ore delineation.

Jan 1, 2000

By Sami Hindstrom, Travis Orser, John Starkey

"A great deal of effort has been expended in the last 11 years by the authors and others to identify the correct power required to grind ore in a SAG mill, by developing ore hardness variability functions for the ore body to be mined. This paper describes the next step in the SAG design process, which is choosing a SAG mill to accomplish the required specified design performance.At the test work stage, each ore hardness data point is a unique and discreet bit of information that represents the energy required to grind the ore represented by that sample at optimum SAG conditions. When the design criteria are set, it is now considered necessary that the required power draw in the mill chosen be provided at optimum conditions as well.Based on actual 3-ft diameter pilot plant results, we can now show that the grinding efficiency and throughput drop when the optimum load limit is exceeded. Future work is expected to show a similar reduction in efficiency when exceeding optimum speed. Providing specified power by exceeding these optimum conditions is not adequate and leads to a lower cost but underperforming SAG mill.It is possible in some cases to modify a SAG circuit to force it to perform better, but this often takes time, much effort and costly modifications. In most cases the capital spent on a properly sized SAG mill may prevent production losses that would be many times greater over the extended start up period. This is the direct result of choosing the proper SAG mill at the start.INTRODUCTIONThe sequential steps required for the design of any grinding circuit, have changed dramatically in the last seven years. Previously, it was considered necessary to do six foot diameter SAG mill pilot plant tests on representative samples of minus six inch ore (F80), in order to understand design requirements. It can now be shown that this method is costly and not likely to produce the desired result because it is difficult to recover six-inch material from deep within a new mine. The representative nature of the sample is often compromised when the sample is selected."

Jan 1, 2003

By Pierre Gratton, Gordon Peeling

The Mining Association of Canada launched the Towards Sustainable Mining initiative in 2004. TSM’s goal is to improve the mining industry’s performance by aligning its actions with the priorities and values of Canadians. The initiative currently includes performance indicators for four areas: tailings management, energy use and greenhouse gas management, external outreach and corporate crisis management planning. Over the past year, the association has been designing a performance assessment and verification system for these performance areas, as its members prepare to move to external verification of their performance in 2006. The presentation will describe the initiative and its evolution, as well as the challenges faced in developing a verification system applicable to an entire sector.

Jan 1, 2006

By E. J. Burrough

Coal Reserves The Crowsnest Pass coal fields form part of a greater area which comprises the Inner Foothills belt of the Alberta coal fields and the southeastern coal fields of British Columbia. The most valuable and most extensive reserves of the bituminous coals of Canada are concentrated in this?area, of which the Crowsnest Pass fields form an important part. The extent of these coal reserves together with those of the rest of Canada were recently studied by the Geological Survey of Canada for the Royal Commission on Coal of 1946 (1). Quotin from the report, it is of interest to note that, prior to this work, the most widely known, and in fact the only Canadian-wide estimates of, coal reserves of Canada available to the Commission were those prepared by Dr. Dowling in 1913 (2). At that time it was estimated that Canada's reserves of coal were over twelve hundred billion tons. The more recent estimates of mineable coal for the whole of Canada are of the order of 10 per cent of that figure and are reported. as 99 billion tons, which is further reduced to 40 billion tons on the basis of the estimation of recoverable coal. This considerable divergence in estimated reserves is explained in part by the big difference in the bases of measurements. For example, in the original report, seams of one foot occurring at a depth of 4,000 feet were included in the estimates.

Jan 1, 1951

By A. Kapoor, L. Morin, S. Mortazavi, P. Béedard, Gould. W. D., A. Kuiper

The degradation of thiocyanate in a simulated gold mill effluent was studied using a laboratory scale rotating biological contactor (RBC). Complete SCN- removal was obtained at temperatures of 8 and 12°C, and a hydraulic retention time of approximately 3.3 h. The NH4+ produced by thiocyanate hydrolysis was oxidized by nitrifying bacteria to NO2 and NO3-. The HS- produced by thiocyanate hydrolysis was chemically and biologically oxidized to elemental S, which was subsequently biologically oxidized to sulfate. Incomplete sulfur oxidation occurred in the RBC, particularly at 8°C and elemental sulfur deposition was observed on the RBC disks. The RBC feed exhibited toxicity to rainbow trout but the RBC was effective in removing the acute toxicity of thiocyanate.

Jan 1, 2005

By S. Isaac

The networks of interdependencies between elements in building projects, referred to as the project topology, are often complex and difficult for project teams to comprehend. It is hypothesized that a graphbased model of the project topology can be based on existing data in Building Information Models (BIM), facilitating the application of graph-theoretic algorithms to analyze this topology. The objective of this study is to propose an outline for the synthesis of BIM and graph theory. This synthesis is expected to contribute to the development of new tools for representing, managing and analyzing the design of building projects.

Aug 1, 2013

By Maciej Wrobel, Joerg Hammerschmidt, Dana Nurgaliyeva, Alexandros Charitos, Jochen Guentner

"Smelting of copper concentrates in the flash smelter generates a flue dust stream that contains a substantial amount of copper and accumulates more than half of the arsenic input to the smelter. In view of its high copper content flue dust recirculation to the flash smelter is common practice. Globally traded copper concentrates are affected by ever increasing arsenic contents and cause an increasing circulating arsenic load in flash smelter operation. Control of the arsenic level in the smelter slag becomes a challenge. This interaction of arsenic loaded copper feedstock, need for flue dust recirculation and slag quality control call for possibilities to reduce the arsenic load of the recirculated flue dust stream.The technology of partial roasting is known from pre-treatment of copper concentrates before smelting, and gold concentrates before cyanide leaching, to remove the harmful element arsenic. The partial roasting technology can be adapted for use in the purification of the flue dust. A major challenge for flue dust treatment is its extremely fine particle size compared to usual concentrates. For this reason Outotec developed a new process, which allows handling of such fine flue dust. This process solution provides an efficient possibility to reduce the arsenic burden in copper smelter operations.The suggested process aims at reducing the arsenic load to the smelter by treating the flue dust prior to recirculation to the smelter. The presented results are based on test work in the Outotec R&D-centre in Frankfurt. It is possible to remove 80-85% of the contained arsenic and to collect it in an arsenic trioxide residue with a concentration above 90%. The final off gas contains SO2 from decomposition of sulphates that are contained in the flue dust. The off gas stream is relatively small. We assume that it is possible to combine the off gas stream with other smelter process gas streams and to treat it in an existing sulphuric acid plant. Coal is used as fuel and as reductant to reduce pentavalent arsenate to trivalent arsenite. Arsenite can be kept in gas form at temperatures above 450°C. This permits separation of a calcine stream with arsenic levels of 0.2 – 0.3%, which is recirculated to the furnace.Outotec has a wide range of roasting testing facilities from lab-scale to pilot-scale. Outotec has both capability to modify and adapt technology to specific ore or concentrate requirements, but also the necessary infrastructure in its research centers in Frankfurt and Pori to do appropriate validation tests in lab and pilot scale size plants."

Jan 1, 2016

By Alex Rown

"THE SYDNEY COAL FIELD has long been afflicted by high costs and low productivities. However, a distinct possibility now exists that improvements can be made in costs, productivities and revenues. If these hopes materialize, the Sydney coal field will once again be regarded as a valuable asset in our national inventory of energy and metallurgical coals. The economic possibilities for the Sydney collieries depend on performance at the pits and in the market place. Because this audience is already well informed about colliery planning, I would like to start with an assessment of the modern coal market insofar as it may relate to the Sydney field. Since 1950 we have seen a vast growth in the population and industrial empires of the western world which has resulted in an enormous and escalating demand for energy. If the energy supply pattern of the first 50 years of this century had been followed, this would have led to an immense demand for coal."

Jan 1, 1972

By E. A. Roux

As the first mine-to-metal zinc operation utilising atmospheric leaching, solvent extraction and electrowinning, Skorpion Zinc faces unique challenges and opportunities. One of these challenges is found in the solvent extraction circuit, in which di-ethylhexyl phosphoric acid (D2EHPA) is used as the organic extractant. Although D2EHPA is an excellent extractant for zinc, it suffers from the co-extraction of ferric iron, which is produced during leaching and by the corrosion of the grinding media. This situation is partially mitigated by iron precipitation in the neutralisation step prior to solvent extraction. Unfortunately, some ferric iron still reports to the solvent extraction process. This leads to a slow build up of iron in the organic phase. Chemical stripping is used to maintain the Fe concentration at an acceptable level. In this paper, the efficiency of the iron removal process is discussed.

Jan 1, 2006