Search Documents

By E. Ghali, W. Zhang, G. Gabra, N. Sorour, G. Houlachi

The additives polyacrylamide, 1-Butyl-3-methylimidazolium chloride, Tetra-butylammonium bromide, Benzalkonium chloride and chitin are evaluated during zinc electrolysis from synthetic acidic sulphate electrolyte containing Mn2+ ions, in absence and in presence of 0.0055 mg dm-3 of Sb3+ ions. Galvanostatic polarization tests for 2 hours at 50 mA cm-2 and 38oC were carried out to determine the cathodic and anodic potentials, and current efficiency of the deposited zinc. Potentiodynamic polarization and cyclic voltammetry tests have also been employed to study the electrochemical behavior of each additive on the zinc deposit on aluminum electrode. Results showed that, in presence of Sb3+, adding 1 to 3 mg of 1-Butyl-3-methylimidazolium chloride increases the cell voltage by ˜0-7 mV. Current efficiency is increased by ˜4.90-6.40%; power consumption is reduced by ˜147-173 kWh t-1 by adding 1-3 mg, respectively. However, in absence of Sb3+, cell voltage is decreased by ˜7-28 mV, current efficiency is increased by ˜0.70-1.50%; power consumption is reduced by ˜41-47 kWh t-1 by adding 1-3 mg. The effect of the other additives on cell voltage, current efficiency, lead content and morphology of zinc deposit has also been examined. Surface morphology and crystallographic orientation of the deposit was studied using scanning electron microscopic (SEM) and X-ray diffraction (XRD), respectively. The content of lead in the deposit has also been measured using inductively coupled plasma spectroscopy (ICP).

Jan 1, 2015

By Gerald Blackmore

This paper discusses the present state and future trends within the coal industry, and then goes into the reasoning behind these planned trends. Such factors as marketing, costs, new mining techniques and machinery, and manpower and human resources are considered. Finally, the author refers to the effect that these trends will have on the coal industry of Cape Breton.

Jan 1, 1968

By A Falter

Gyroscopic surveying instruments, which apply the physical law of a gyroscope, are being used for deter-mining the azimuth of lines with a high degree of ac-curacy. In the past ten years, gyro-theodolites have been introduced widely for underground orientation in the mining industry of Russia, Germany and South Africa. Gyroscorpic methods eliminate awkward procedures of conventional shaft plumbing, and provide more safety, excellent control and the highest precision at any point under-ground without interference with hoisting operations. The advantages of gyroscopic orientation in geodetic surveys become obvious in primary and secondary triangulation, in the determination of co-ordinates of single triangulation points, using the method of trigonometric re-section and intersection, and when traversing over long distances or in areas with obstructed view. Other fields of application are found in geophysical surveys and in the orientation of technical objects; e.g. radar stations, relay stations and ballistic missiles.

Jan 1, 1964

By G. H. Robbins

"Originally presented at TORONTO 94, CIM-AGM, this paper has been updated to reflect the present status of business development for theSO2/AIR process. The paper reviews the back-ground leading to the invention, discusses the process chemistry and historically tracks the commercial development. Engineering and cost considerations are presented.IntroductionThe year 1994 was particularly significant in terms of the technical and business development of the INCO SO2/AIR cyanide destruction process. The year marked a decade of service to the world mining community since INCO acquired the Canadian patent in 1984. In that time period, the technology had become widely recognized as the state-of-the-art process in the field of cyanide detoxification and today we enjoy the distinction of having licensed the process at over 50 project sites worldwide. The application for the process has mostly been in the mining industry in precious metal recovery plants where it offers treatment for a wide range of waste streams such as: CIP/CIL slurries, Merrill-Crowe barren bleed solutions and/or re-pulped filter cakes, tailings pond water recycle or discharge, make-up water to flotation circuits and feed to underground backfill plants. The process also applies to the treatment of high cyanide rinsewaters from metal plating shops. More recently the process is being applied to the rinsing and abandonment of heap leach pads where it has proven to be a very cost-effective application of the INCO process. The distinct advantages that have led to the success of the process are the ability to work on slurries as well as solutions and the significantly low cost of sulphur dioxide products. The process is safe and easy to manage and uses all forms of SO2(liquid, gas or salts) which gives the process tremendous versatility with respect to geographic application. Having more than ten years of service"

Jan 1, 1996

By Jean-Francois Magnan

"The old conventional process to produce lithium raw material dates from 1954 (CA patent #504477A). This process produces low purity lithium carbonate (Li2CO3) only. To obtain battery-grade carbonate, another polishing process is needed. To further obtain lithium hydroxide, another chemical conversion process is needed. That is why historically, the value of lithium hydroxide has always been higher than that of the lithium carbonate precursor. With the old conventional process, the low quality lithium carbonate is precipitated from a lithium sulfate solution (Li2SO4) by adding soda ash (sodium carbonate and its impurities). The resulting reaction produces significant quantities of sodium sulfate (salt cake) as a by-product with amounts larger than the impure Li2CO3 recovered with part of the soda impurities. When this conventional process was invented, the salt cake by-product was not an issue: it was discarded in a river near the plant. This practice cannot be done today in North America. While looking to find a solution for salt cake, electrolytic salt splitting of Na2SO4 into NaOH and dilute sulfuric acid appears as a technically feasible solution to get a rid of the salt cake. However, the sodium sulfate salt splitting process has difficulties to economically compete with the chlor-alkali process, which produces millions of tons of NaOH from sodium chloride (NaCl) every year.In contrast, the process developed by Nemaska to directly produce LiOH by Li2SO4 salt splitting not only solves the environmental problems related to the conventional process to produce lithium carbonate raw material, it also produces very high purity lithium hydroxide monohydrate directly at very competitive OPEX cost in comparison with industry peers (Figure 1). It also drastically reduces the amount of reagent and the direct greenhouse gas emissions."

Jan 1, 2016

By L. Bratek, K. Jaworek, M. Czaplicka

Methods for arsenic compound removal from aqueous solutions include processes such as: coagulation, adsorption, membrane techniques, electrochemical and biotechnology techniques. Advanced oxidation using both UV radiation and strong oxidizing agents such as ozone and hydrogen peroxide may also decompose these compounds. It is known that effluents from metallurgical processes contain inorganic arsenic compounds in addition to the organic compounds such as: dimethylarsinic acid and phenylarsonic acid. This paper presents the conditions that lead to the formation of deposits containing mainly arsenic, such as pH, the wavelength of the radiation and the type of oxidant, for this type of effluent.

Jan 1, 2014

By H. J. H. Pieterse

Agitation requirements in oxidation autoclaves can vary widely depending on the mineralogy of the feed material and the specific process selected. Before selecting an agitation system it is important that the client specify the desired throughput, mineralogy, chemistry, kinetics, compartments, overall retention time, and the desired oxygen utilization. In selecting the agitation system, the factors mentioned above as well as oxygen solubility, oxygen mass transfer coefficients, and specific power are evaluated. Much research effort has been directed toward open tank systems for fermentation and oxidation processes. However, for high pressure autoclave oxidation processes little information is available. In this review the author's experience in the autoclave industry and some of the available literature are utilized to compare the installed power per unit volume with some of the methods proposed for open tank oxidation. Equations that appear to give results close to that experienced in the industry have been identified. Further work is required in this area to develop a higher degree of confidence in the ability to predict the power required for any given case.

Jan 1, 2004

By P. H. Agson Gani, T. Sitorus, N. P. Widodo

"PT ANTAM UBPE Pongkor underground mine use blasting to develop its tunnels which will cause poisonous and dangerous gases trapped inside mine. To analyze this case, a study of mine ventilation, the dispersion of carbon monoxide (CO) gas concentration and diffusion coefficient is commenced. At the end, the re-entry time formula will be determined. Results indicate that this study is site specific and could only be applied in the place this study executed. The aim of this study is to be further developed by applying Principal Component Analysis (PCA) to find a universal re-entry formula. KEYWORDS Mine Ventilation, Re-Entry, Smoke Clearing, Diffusion Coefficient, Carbon Monoxide Gas, Gas Dispersion INTRODUCTION Pongkor underground mine is using cut and fill as its mining method. Thus, its development and production processes require blasting to develop its tunnel. This process caused poisonous and dangerous gases spread and trapped inside the mine, one of them is carbon monoxide (CO) gas. CO is formed in an unbalanced reaction of explosives detonation and could be the cause of headache, blackout and death to people who inhale CO at certain concentration (McPherson, 2011; Hartman, Mutmansky, Ramani, & Wang, 2012). Mine ventilation system is installed in the mine to resolve this problem. Mine ventilation play an important role to disperse CO gas by absorb the poisonous/dangerous gases and deliver clean air into mine. The important parameter is diffusion coefficient, because diffusion is affecting particulates or gasses spreading from its sources throughout the mine. Diffusion coefficient is the total diffusion in axial direction of turbulent flow mainly by convection of bulk motion, advection and eddy diffusion, while the effect of molecular diffusion is appreciably negligible (Widiatmojo et al, 2015). Taylor (1953, 1954) develops a theory about the dispersion by inducing a slow stream of solvent into a capillary tube. Taylor used Reynolds assumption of radial diffusivity to be analogous with the transfer of the matter in turbulent flow as well as the transfer of momentum and heat. Then, Taylor proposed the formula of diffusion coefficient, D (m2/s), against pipe diameter and turbulent shear velocity are as follow:"

Jan 1, 2019

By F. Siciliano, D. Bai, S. Yue, A. M. Elwazri

The influence of niobium addition and very low temperature (`cool') deformation on the microstructure and properties of low carbon microalloyed steels was investigated. In this work, the specimens were heated at 1200°C and held at this temperature for 20 minutes. Some specimens were aged at 400°C for times ranging from 10 minutes to 10 hours followed by air-cooling. Others were subjected to deformation at 400°C (`cool deformation') prior to aging. It was observed that the proportion of acicular ferrite was increased as the amount of Nb was increased. It was found that cool deformation increased both yield and tensile strengths significantly compared to that of the aged only specimens.

Jan 1, 2005

By P. W. Ware

The majority of all refined copper is consumed to produce electrical conductors. Most copper conductors are drawn into wire from 8 mm ETP copper rod produced from high purity copper cathodes. Southwire Company has more than 40 years experience using, designing, fabricating and marketing a process for continuously producing ETP copper wire rod. This process is called the SCR® (Southwire Continuous Rod) process. Today, approximately half the copper wire rod produced in the world, or more than one third of all refined copper consumed, is produced using the SCR process. Southwire has sold 75 SCR copper rod mills to metal producers and wire manufacturers around the world. Southwire is North America's largest electrical wire and cable producer. Southwire operates a 48 metric ton per hour SCR® copper rod system in Carrollton, Georgia. This allows Southwire to provide technical support for existing SCR® system customers based on first-hand knowledge. Rod fabricators and their wire customers are always striving for copper rod that improves productivity. They are looking for improved surface quality, finer wire sizes and fewer wire breaks per ton of rod drawn. This paper will present a brief history of the SCR® process, a description and recent process developments.

Jan 1, 2007

By Allan R. Punkkinen

Safe extraction of the valued ore resource in the deep levels of VALE Creighton Mine has progressed in a pillar-less fashion using vertical retreat, slot-slash and uppers retreat methods since the cessation of ?cut and fill? mining in the late 1980?s. Sequencing of the panel extraction and filling has been the key to successful exploitation of high stress orebodies at depth. In late 2010, discussions between the Operating Department and Creighton Ground Control revealed an opportunity to evaluate a trial primarysecondary sequence in the west end of the 400 Orebody at the 2340m horizon. To manage the trial primarysecondary project, a high level risk analysis and management of change was carried out to mitigate potential danger. As part of the requirements, an instrumentation project was conducted in the hanging wall and footwall bottomsills of the secondary panel and within the secondary panel itself. The extraction sequence was modeled with Map3D® software, confirming high stress levels with the advance of the primary panel. Enhanced ground support was installed based on modelling results. A key objective of the instrumentation project was to verify support system response to mining and to obtain knowledge in regards to the behavior of the stope. This paper describes the first time that this type of new innovative instrumented rockbolt technology had been used in a hard rock mining environment. Understanding of the physical deformation mechanisms of ground support in response to high stress conditions is the basis for an effective ground control strategy. The data played an important role in subsequent enhanced ground support system design at the mine and importantly, established the fact that the secondary pillar had not totally failed. Subsequent cavity monitor results helped establish that fact.

Jun 1, 2012

By H. R. Oliveira, C. R. Aragonez de Vasconcellos

Pipeline operation and maintenance necessarily involves geotechnical studies at points and areas with deflagrated instabilities or still to map and monitor areas prone to geotechnical problems. Landslides, erosions and debris flows are some examples of natural hazards, that not rarely, can bring high consequences to pipelines, sometimes leading them to high stresses levels and ruptures. Bolivia-Brazil Natural Gas Pipeline has 2.593 kilometers since Rio Grande City in Bolivia until Canoas City, in south Brazil. The pipeline crosses a lot of types of geological fields and difficult topography. The south spread of the pipeline has the most prone areas to geotechnical hazards because of its hard topography combined with the variety of geological materials, such as, colluvium deposits and debris flow areas. The aim of this paper is to present the right-of-way geotechnical risks that affect pipelines, presenting some practical remedial works done by TBG at Bolivia-Brazil Natural Gas Pipeline as well as the integrity plan and the adopted actions in way to prevent geotechnical accidents.

Jan 1, 2005

By T. G. Joseph, M. Bolster, M. Curley

"High tirerim loading on haul trucks operating on rough ground frequently manifests as mechanical separations and rim base cracking caused by cyclic fatigue. This paper provides an understanding of the impact of high loads on rim component life and tire footprint, bulge, and deformation behaviour; and develops a maintenance planning tool to predict strain implications of high g loading for a given rim location. Loading tests and analyses were conducted for a tirerim arrangement under increasing load and internal tire pressure. Graphical models were developed, allowing higher g load extrapolation predictions for specific rim components.KEYWORDS g load, Mining, Model, Prediction, Rim, Strain, Tire bulge, Tire footprint, Ultra-class vehicleRÉSUMÉ L’application d’un chargement élevé sur le système pneu/jante de camions de transport rou¬lant sur des terrains accidentés se manifeste fréquemment par des séparations mécaniques et une fissure à la base de la jante engendrée par une fatigue cyclique. Cet article nous permet de mieux comprendre l’incidence de l’application de charges élevées sur la durée de vie des composantes de la jante ainsi que sur l’empreinte, la hernie et le comportement de déformation des pneus. Il développe également un outil de planification de l’entretien visant à prévoir l’incidence des contraintes en cas d’application d’un chargement g élevé sur un endroit donné de la jante. Des essais et des analyses de la charge ont été effectués pour un agencement pneu/jante soumis à une charge et une pression interne du pneu croissantes. Des modèles graphiques ont été développés, ce qui a permis d’établir des prédictions sur la base d’une extrapolation du chargement g plus élevé appliqué à des composantes spécifiques de la jante.MOTS CLÉS charge g, contrainte, empreinte du pneu, exploitation minière, hernie du pneu, jante, modèle, prédiction, véhicule ultralourdINTRODUCTION The purpose of this paper is to report on a proposed and trialed tire performance test based on data obtained from controlled testing that is used to predict the impact of high g loading on hauler rims and tires with greater accuracy. For example, for many years oil sand mining operations have expressed qualitative beliefs that an impact load of the magnitude experienced by a rim and tire arrangement is not detrimental to a rim as a stiff component; however, mining equipment components are subjected to cyclic loading where failure can result from repeated load/unload activity, truncating the peak region of a stress–strain response and resulting in fatigue failure at a stress value that is less than the peak value. The outcome reported by oil sand haul truck maintenance groups indicates they have realized that most high g impacts—such as those experienced by hauler tires and rims operating on poor ground conditions—can result in failure due to cyclic loading, where higher loads require fewer cycles for failure. This high-level loading and the resulting strain transmitted to the rim is evident in the results of the laboratory testing presented in this paper."

Jan 1, 2019

By Jayne Somers

Methane (CH4) is a potent greenhouse gas, accounting for 15 percent of all global greenhouse gas emissions in 2005. Since methane has a much shorter atmospheric lifetime than carbon dioxide (CO2), reducing methane emissions can achieve considerable climate benefits over the next 25 years. Coal seams often contain significant quantities of methane and CH4 released to the atmosphere from gassy mines during coal extraction is a major source of greenhouse gas emissions. Methane (CH4) emissions from coal mining activities constitute approximately 6% of total global human-related methane emissions. Coal mines around the world have recognized that methane is a clean energy resource that can be captured and used productively. Coal mine methane (CMM) is currently utilized for power generation, natural gas pipeline injection, vehicle fuel, industrial process feed stocks, on-site mine boilers, mine heating, and home heating distribution systems. Upgrading mine degasification systems can often improve gas quality and create favorable project economics. The United States has been a leader in coal mine methane (CMM) recovery and use since the 1990?s. There are now 15 projects at active underground mines in the U.S., as well as 26 abandoned mine methane projects. Recovery and use projects at active underground U.S. mines reduced methane emissions by approximately 49 Billion cubic feet in 2010. In an exciting new development, a ventilation air methane (VAM) mitigation project at the CONSOL McElroy mine in West Virginia was installed by Verdeo. Operational since September 2012, this is the first commercial-scale VAM project in the U.S. and the project will reduce methane emissions by an estimated 920 MMCF/yr. As part of the U.S. Greenhouse Gas Reporting Program, actual data on methane emissions from underground coal mines was collected for the first time in 2011 and reported to U.S. EPA in September 2012. The data collected will help inform stakeholders, particularly the underground coal mining industry, of CMM emission sources on public and private lands. The detailed data will also shed light on the specific sources of methane from active underground coal mines and highlight project opportunities for the U.S. coal industry. The paper will cover U.S. coal mine methane emissions, U.S. CMM utilization and destruction projects, Federal policies and State incentives for CMM capture and utilization. 2011 CMM data from the U.S. Greenhouse Gas Reporting Program Subpart FF will be analyzed and compared with previous U.S. Greenhouse Gas Inventory estimates. Other developments, including the voluntary carbon market, will be discussed.

Aug 1, 2013

By F. Chachula, A. Molinaro

"Sulphide mineral flotation operations continuously strive for a balance between mineralogy, mineral liberation, circuit conditions and reagent solutions to maximize the production rate and recovery of payable metals. The Taseko Gibraltar copper – molybdenum mill operations underwent an extensive project focusing on the fundamentals to identify the effects of process conditions and mineral liberation to improve the bulk circuit copper – molybdenum recovery efficiencies in the bulk flotation circuits. This discussion will provide process data that demonstrates; 1) fundamental relationship between mineral liberation to recovery and grade, 2) flotation circuit condition testing and optimization, 3) reagent combinations resulting in efficient/economical mineral recovery, and 4) the development of a xanthate free reagent solution. The data presented and discussed will also touch on flotation parameters including pH, retention time, kinetics and the effect on bulk circuit recovery performance.INTRODUCTION Taseko's is the owner (75%) and operator of the Gibraltar copper-molybdenum mine, located in south-central British Columbia, the second largest open pit copper mine in Canada and the largest employer in the Cariboo region. Taseko restarted Gibraltar in 2004. From 2006 until 2012, the company invested ~$700 million to expand and modernize the operation which was originally scheduled for demolition when the company acquired it in 1999. In the spring of 2011, construction commenced for Gibraltar Development Plan 3 (GDP3). GDP3 included the construction of a standalone 30,000 ton per day concentrator, built adjacent to the existing 55,000 ton per day facility. The new design capacity of Gibraltar was designed to be 85,000 tons per day. An integral part of the project was a new molybdenum recovery facility. In addition to the new concentrator, the mining fleet was upgraded with a new mining shovel, production drill and ten haul trucks (Taseko, May 2015). In May of 2015, the Company completed an updated mine plan for Gibraltar featuring a 50% decrease in strip ratio. This new mine plan was a result of a detailed, six-month engineering study and forms the basis of an updated NI 43-101 compliant reserve (Taseko Announces Improved Economics At Its Gibraltar Copper Mine, 2015). The new mine plan took into account lower milling costs as a result of the modernized processing facilities (Taseko, May 2015)."

Jan 1, 2018

By Nirmal Weerasekara

Mill liners serve the dual purpose of protecting the shell from wear and transferring the rotary motion of the mill to an effective grinding action. As the liners wear, the efficiency of energy transfer changes, so there is balance between liner profile for wear and for milling efficiency. A tool that can simultaneously predict the evolution of the liner profile and the associated change in milling efficiency should prove most useful in optimal liner design. This paper presents such an approach, based on measured 3D liner profile data informing 3D DEM simulations of charge motion and liner wear modelling.

Jan 1, 2012

By T. Grammatikopoulos, SGS Canada Inc.

"The Nechalacho rare metal deposit, located in the Northwest Territories, Canada, is currently being taken through Feasibility Study by Avalon Rare Metals Inc. QEMSCAN analysis and supplementary electron microprobe analysis were utilized to identify and quantify the mineralogy of the deposit, and determine REE distribution among the minerals. QEMSCAN mineralogy was performed to provide textural information on the mineralization, determine the variability of the ore and identify REE domains, and the liberation and association of the REE minerals. The sample matrix consists predominantly of silicate minerals. The REE minerals include allanite, monazite, synchysite, columbite, fergusonite, and bastnaesite. Zircon is present in considerable amounts and is a REE carrier. Fergusonite and zircon account for most of the HREE, and monazite, allanite, synchysite and bastnaesite the LREE. QEMSCAN mineralogical data is extremely valuable in assessing the mineralogy of the ore. The data are implemented to define the mineralogy of the ore body, support metallurgical test work, and predict recoveries and grades.INTRODUCTIONThe term rare earth elements (REE) is used to describe the 15 lanthanide elements or metals and, more recently, the metals yttrium and scandium, which display similar physical and chemical properties.Economic and potentially economic REE deposits form two main groups, a more commonly occurring “light rare earth element” (LREE) group containing lanthanum, cerium, praseodymium, neodymium, and samarium and a less commonly occurring “heavy rare earth element” (HREE) group which, in addition to the LREE, contains elevated concentrations of the more valuable REE, europium, gadolinium, terbium, dysprosium, holmium, yttrium, erbium, thulium, ytterbium, lutetium and scandium. The first group is hosted primarily by carbonatites and the second by highly alkaline (Na + K > Al) silicate igneous rocks. The LREE are produced mainly from bastnaesite, monazite, etc., while HREE are produced almost exclusively from low-grade secondary ion adsorption clay deposits in which the REE are adsorbed onto the surfaces of kaolinite and halloysite, clay minerals produced by the weathering of granite and sediments. HREE are also found in fegusonite, zircon, xenotime, etc but are not produced presently from these minerals. China is responsible for 97% of the World’s production of the REE, mainly from the giant Bayan Obo, carbonatite-related deposit and from the clay deposits mentioned above.Quantitative automated mineralogy is increasingly being applied to ore deposits. It helps users to understand and improve mineralogical parameters for geological and metallurgical purposes. Data include textural characterization, to quantification and distribution of ore and gangue minerals, liberation and association of the REE minerals. The data can be used to define mineralogical domains and predict the metallurgical response of the ore (Gunning, de Souza, & Grammatikopoulos, 2009)."

Jan 1, 2012

By A. O. Dufresne

The mineral wealth of pre-Cambrian rocks in Canada has been the subject of much study by geologists and engineers (members of this Institute), particularly so in the past few years, following discoveries of mineral deposits in areas far a part. This interest is well worth sustaining knowing the numerous rich producing mines within the pre-Cambrian formations, and the vast area covered by its rocks throughout this country. The pre-Cambrian has yielded minerals, both metallic and non-metallic; of these a much diversified list could be made. In more than one district we can point to mining as being responsible for the opening up of new sections, attracting a population into regions which otherwise would have remained virgin land of little commercial value. In these pre-Cambrian formations are found the rich copper deposits of Michigan, producing without interruption since 1845, and from which seven billion pounds of copper has been won; while in Minnesota and the adjoining district, at the head of Lake Superior, are mined iron ores which have rendered possible the great steel manufacturing industry of United States, the base of the economic structure of that wealthy country. The pre-Cambrian has given Canada the nickel-copper mines of the Sudbury district, the silver deposits of Cobalt and the gold camps of Porcupine and Kirkland Lake. With all of these our members are familiar; and it suffices to mention them to bring to mind pictures of the wealth and 'the growing population, in a word the importance of mining in?those sections of the country.

Jan 1, 1926

By D. L. Cluff

Ventilation Air Methane (VAM) is a high volume low concentration methane source. The capture or use of methane from VAM is challenging, which results in the routine discharge of methane into the atmosphere. Mitigating VAM has the benefits of providing an energy source and reducing the atmospheric Greenhouse Gas (GHG) burden. The GHG radiative forcing effect of methane is 17?23 times as potent as carbon dioxide on a 100-year time horizon. Thus, any reduction in atmospheric methane would be beneficial. The calorific value of methane is 55.5 MJ/Kg; therefore, a 100 m3/s flow with VAM concentrations from 0.1?1% can provide 3.8?38 MW of exploitable power. Strategies to mitigate VAM such as: Thermal Flow Reverse Reactors (TFRR), Catalytic Flow Reverse Reactors (CFRR), Lean Burn and Catalytic Gas Turbines, Biothermica Vamox®, Megtec VOCSIDIZER©, and Vamcat? are briefly reviewed. The review of VAM mitigation technologies reveals disadvantages such as the need to maintain a minimum internal heat capable of oxidizing the methane. This requirement uses all of the available methane up to the point of reaction sustainability and up to half at the highest methane concentration in VAM. Some systems may introduce a pressure drop to the ventilation system, which would impinge on the existing ventilation system design. These impediments necessitate the development of a more amenable technology. In the proposed system, gas turbines (GT), coupled to a combustion chamber with an external fuel supply, assist the combustion of the VAM. The combustion-chamber coupled system provides electricity, while the heat contained in the GT exhaust gases increases the temperature of the VAM, encouraging the development of a flame inside a combustion chamber. The flow from the combustion chamber streams through a primary air/fluid heat exchanger capable of producing steam of a high enough quality to generate electricity using conventional steam turbines. The residual heat after primary extraction, directed through other equipment, provides additional heat based products such as industrial scale dry air, chilling by an absorption chiller or hot water. The overall design of the system is scalable for low to high VAM flows or variations in concentrations and is capable of providing the company or community with heating, chilling, hot water, electricity or motive force as needed by the particular site or community. The Multi-generation system uses heat from three sources to provide clean efficient energy while mitigating the atmospheric emissions of methane. These sources are heat from the GT, often considered waste heat, heat from fuel injected into the igniters and heat from the VAM. The opportunity to collect carbon credits may improve the economics. In order to design a system with this capacity, a detailed analysis of the combustion characteristics of three separate flows is required. VAM is the main airflow, having the highest volumetric effect, while the GT exhaust and the additional fuel added to the hot exhaust flow of the gas turbine are lower flows, but have a higher velocity and temperature. The aim of the modeling undertaken in this work is to establish the combustion dynamics, degree of pre-heating required and the geometry essential to the design of combustion based VAM mitigation multi-generation systems.

Aug 1, 2013

By N. W. Xu, M. D. Wei, F. Dai, B. Li

"Chevron notched samples achieve general acceptance for measuring the Mode-I (opening mode) fracture toughness of rocks. The cracked chevron notched semi-circular bending (CCNSCB) sample, which is developed from the International Society of Rock Mechanics suggested the cracked chevron notched Brazilian disc method, has recently received much attention. However, these chevron notched methods have not been fully mastered, some ideal assumptions based by their theories and formulas, such as the straight-through crack assumption (STCA), have not been verified detailedly. Fractures of CCNSCB specimens were numerically simulated considering different heterogeneities, geometrical and mechanical parameters. The results show that, the real fractures of CCNSCB specimens are never satisfied with the STCA. In fact, micro fractures not only occur in the notch tip but also the two chevron edges. Consequently, the crack front features prominently in a shape of parabolic curve, far from being straightthrough. Moreover, curvature of the crack front is only affected by shape of the chevron ligament. Cracks usually start from two sides of the notch tips rather than center of the notch width, and propagate deviating from the postulated fracture routes. These fracture mechanisms induce errors with the measurements, and thus more attentions should be paid to the real fractures of the chevron notched samples for measuring fracture toughness more accurately. INTRODUCTIONWith the increasing requirement of people for resources and energies, frequent rock engineering activities have been conducting, such as underground excavation, oil exploration and deep burial of nuclear waste. Many problems appear in rock fracture. Consequently, there are more and more attentions paid in rock fracture mechanics due to its broad application prospects for solving these engineering problems. Since Mode-I (opening mode) fracture is the most common failure mode in rocks, Mode-I fracture toughness is a primary parameter to predict rock mechanical properties in actual engineering, and thus its accurate values are necessary to the researches of rockburst, rock mass slope stability, rock cutting, hydraulic fracturing, tunneling, et al. Therefore, it is thus significant to evaluate and study relevant methods to obtain the reliable value."

Jan 1, 2015