Search Documents

By R. Holmwood, M. Faris, P. Holloway, M. Collins

Sulphuric acid addition is a major driver of the economics in the processing of nickel laterite ores by high pressure acid leaching (HPAL). Understanding the optimal acid addition rate is essential for the success of any HPAL operation, and this is especially true at Ambatovy, where the composition of the feed tends to vary significantly on a day-to-day basis. Most studies on the effect of acid on nickel extraction in HPAL have used laboratory testwork as their basis. Although these studies are invaluable in assessing the economics of a new project, they are limited by the range of ore composition that can be tested and the differences between the operation of the laboratory equipment and the commercial plant. To enable optimization of the acid addition at Ambatovy, operating data from the HPAL operation were obtained using OSISoft’s PI system and the data from several periods were examined to develop relationships between acid addition and nickel extraction. The initial relationships from 2014 focused on the acid required to achieve a target nickel extraction of 95%, with aluminum and magnesium in ore and feed slurry solids content as the major variables. As Ambatovy ramped up through 2015 and 2016, the calculated acid requirement was further refined to address the effects of HPAL temperature and retention time, and the oxidizing/reducing characteristics of the ore, and to generate acid requirement relationships as a function of ranges of nickel extraction. These relationships supported raising the target nickel extraction to 96% and enabled the development of an economic model between acid addition and nickel extraction.

Jan 1, 2017

By J. R. Morris

"A hoisting plant design should satisfy two basic requirements:1. to provide the necessary materials handling capacity, including ventilation where applicable, while meeting the requirements of good practice and, as a minimum, government regulation; and2. to optimize the economics of the project. Selection of hoisting equipment to meet the first objective is a complex but logical engineering process. The necessary calculations of payloads, accelerations, speeds, rope strength, hoist size, and power requirements are very readily carried out on computers or programmable calculators. A variety of hoist options can be quickly examined to assess the effects of changes in design parameters.Meeting the second requirement involves balancing the costs of various hoist arrangements and shaft designs, together with the time cost effects of differing shaft sinking rates and potential advances to be gained by concurrent level development. The proposed mine layout is significant here, as is the possibility of future shaft deepening and/or production increase. The availability of used equipment may be significant, both as regards first cost and delivery time. The factors are interactive, with their relative effects .varying from project to project. This paper sets out the primary factors to be considered."

Jan 1, 1990

By S. Koski

The Cerro Verde copper-molybdenum porphyry mine, majority owned and operated by Freeport- McMoRan Copper & Gold, is located 30 km southwest of Arequipa Peru. The concentrator, which produces copper and molybdenum concentrates, started operating in late 2006 with a 108,000 tpd design capacity, processing primary sulfide ore (mainly chalcopyrite and molybdenite). Plant capacity was recently increased to 120,000 tpd. The comminution circuit consists of one 60? x 113" primary crusher, four MP-1000 secondary crushers in closed circuit with dry screens, four 2.4m x 1.6m High Pressure Grinding Rolls (HPGRs) in closed circuit with wet screens, and four 7.3m x 11m gearless ball mills in closed circuit with cyclones. The HPGR circuit is fed by the Secondary Crushing circuit product at a T80 of 35 millimeters, and the HPGR circuit product feeds the Ball Mill circuit at a T80 of 3000 microns. This paper describes operating experiences with HPGRs during these first four years highlighting improvements in operating practices and presentation of data regarding operational efficiencies, also discussed are the primary benefits provided by HPGRs such as production of micro fractured particles, reduced ore Bond Work Index, and reduced power consumption. Cerro Verde represents the first installation of HPGRs in both the copper industry and large scale hard rock mining.

Jan 1, 2012

By Xiong Tong, Jiushuai Deng, Yingbo Mao, Lingyun Huang

Ammonium carbamate has been used as a reagent for the leaching of copper from the copper oxide ore found in the Honghe state, Yunnan province, China. In order to find the optimal conditions for the leaching of copper from this copper oxide ore,the effects of several processing parameters, including the concentration, time, temperature, particle size and stirring intensity have been investigated. The results of these optimization experiments showed that the leaching rate of copper reached up to 72.76% under the following conditions: liquid-to-solid ratio of 10:1, ammonium carbamate concentration of 2.5mol/L, leaching temperature of 45 °C, stirring speed of 300rpm, a reaction time of 1.5 h and 85% by weight thereof passes through a sieve having 0.074 mm.

Jan 1, 2015

By N Robb

This paper gives an account of the laboratory testing, plant testing and final inclusion of the two-stage sulphuric acid leaching process in the Milliken mill. Operational results for September, 1962, are presented, showing a uranium extraction of 95.5 per cent, with a saving of some 16 lbs. of 100 per cent H~S04 and some 9 lbs. of lime per ton milled. Methods for effecting further improvements in the process are indicated. HISTORY P RIOR to the incorporation of two-stage leaching, the process for the treatment of uranium ores at Milliken consisted of a single-stage sulphuric acid leach, followed by a solution recovery step involving washing in thickeners and two-stage filtration. The thickener overflow solution was subsequently concentrated and purified by ion exchange, and the uranium was recovered, by two-stage precipitation, as ammonium diuranate. Figure I illustrates this flowsheet. For satisfactory extraction of uranium from the. Milliken ore, a high residual acidity, of the order of 40 grams per litre of free acid in the discharge solution, must be

Jan 1, 1963

By K. Eklund, T. Ahokainen

The Flash Smelting process is the most used production method for primary copper in the world. The basic idea of the Flash Smelting is to utilize the thermal value of sulfidic concentrates and melt the reaction product, in controlled conditions, without a need for external energy. This basic principle is utilized both in matte smelting and in Direct-to-Blister Flash Smelting Processes. In this paper, the behavior of normal (CuFeS2) concentrate of FSF-process is compared to the behavior of high grade feed material produced by Outokumpu Concentrate Upgrade Process with the aid of computational fluid dynamics (CPD) simulation using add-in subroutines developed by Outokumpu Technology. Results consist of the information concerning the behavior of the suspension, reaction efficiency and other parameters concerning the reactions of the feed material. It will be shown that, using the Upgrade Process, the throughput of copper from the Flash Furnace can be almost tripled.

Jan 1, 2007

By C. G. McLachlan

INTRODUCTION The work described in the following paper was under-taken with a view to determining, if possible, the relative importance of some of the phenomena on which flotation seems to depend, in the hope that, if this information could be obtained, it would be of value in dealing with the problem as a whole. At the outset, brief reference will be made to three papers which had a considerable bearing on the course followed in the present investigation. In 1919, Langmuir, in a paper on 'The Mechanism of the Surface Phenomena of Flotation', showed that mono-molecular films of very great stability could be produced on solid surfaces with oleic acid, but that pure paraffin oil, though spreading readily on a dean dry surface, was easily displaced by water.

Jan 1, 1926

By Paul T. Fitzgerald

Risk financing solutions are emerging to fully address environmental liabilities for mining operations. Supported by specialized insurance and alternative risk transfer (ART) products, mine owners can fund, cap and guarantee the environmental liabilities and closure obligations of a mine within a financial structure that will be acceptable to regulators. An environmental risk financing program will permit an owner to transfer the liabilities and indeed the ownership of a site to a third party that has the ability and resources to responsibly execute the closure plan. A properly structured program will be financially viable for the owner and will also respond to community and environmental opposition concerns about sustainable development and the environmental legacies associated with mining activities.

Apr 1, 2005

Over the years, efficient on-line monitoring of performance and status of an electrolytic copper refining process has been challenging due to the need for complex electrical measurement systems and the management of the enormous volume of data. Recent innovative developments by Kennecott Utah Copper Corporation and Outokumpu Technology in wireless cell voltage and individual cell temperature sensing opens new possibilities to improve and modernize tank house management. This paper describes the powerful Outokumpu CellSenseTM refinery monitoring system for efficient interpretation of data produced by wireless CellSensorTM system with traditional refinery measurements. Examples from commercial tank house installations demonstrate the benefits of the system to improved process control and operation. The Outokumpu CellSenseTM monitoring system is simple to operate and accessible to all the plant operation teams.

Jan 1, 2007

By H. G. Warrington

Abstract As part of the active development programme pursued by Dominion Magnesium Limited since 1945, a modern extrusion plant was erected and has been in operation for about twelve months. The only source of nigh purity magnesium in the world, Canadian metal is produced by metallurgical processes within the frame-work of the mining industry, which gives a different viewpoint to every phase of production from other world suppliers of commercial grade metal whose operations are based on chemical industries and techniques. The superior properties of corrosion resistance and grain refinement have aided a programme of standardization, reducing the number of alloys supplied in extruded form from seven to four as an aid to economic production. The first big step was the development of a general purpose alloy known as AZ?21x covering all decorative and medium stressed applications, which will supersede two older alloys. Sales approaching a million feet in this alloy show that it bids fair to become the 'mild steel' of the magnesium industry, its applications ranging from terrazzo floor strip to textile machinery and television mast components. In the high stressed field, metallurgical features preclude low-cost extrusion of the older high-strength alloys, but recent development of a magnesium alloy containing zirconium promises an easily workable metal. Hitherto produced by expensive chemical additions, research now shows that the alloy can be produced by metallurgical means, which may make this alloy available for a wide range of commercial applications. Thus the future development programme for extruded products in the form of tube, bars, shapes, and structural angles and channels may evolve two alloys to cover all applications for strengths up to 52,000 lb. per sq. in. Such standardization is the result of taking advantage of the physical and metallurgical properties of high-purity magnesium instead of accepting techniques based on metal produced by older processes.

Jan 1, 1951

By V. C. Pandolfelli, L. Paulino, C. E. Zangiacomi

The continuous improvement in aluminum industry over the last years has increased metal output at lower cost. The potlining plays an important role in this regard due to high cost involved and more recently in its environmental aspects. In order to increase potlife and thus minimize the aluminum cash cost, a systemic approach is needed, through investigating the main cathode failure mechanisms by using a pot autopsy as a powerful tool, and then making the necessary chances to achieve extended potlife. In addition, preheating and pot start-up may also damage the cathode if not performed with an appropriate technique or even if the lining materials are not specified correctly, among other factors. All these aspects will be presented and discussed in this paper. Increased potlife, especially now that the current is reaching values up to 300kA, will allow aluminum plants to match their goals more efficiently at lower costs.

Jan 1, 2006

By M. A. Gomez, V. Yahorava, J. A. Strauss

"It is accepted widely that pressure oxidation (POX) is the most appropriate technology for processing of arsenic containing refractory gold ores. However, studies on the stability of various iron-arsenic precipitates formed during POX are limited. Since the behaviour of these phases could have significant practical implications for gold processing plants, it is important to study them in isolation. This paper compares two synthetic precipitates, basic ferric arsenate sulphate (BFAS) and basic ferric sulphate (BFS) in terms of their formation, behaviour during hot curing and cyanidation, as well as their environmental stability. BFS and BFAS were synthesised hydrothermally at 205°C and their mineralogy was confirmed using various techniques. During synthesis, the addition of H3AsO4 into an aqueous Fe2(SO4)3-H2SO4 mixture significantly decreased the iron yield to BFAS in comparison to BFS under equimolar initial iron and acid concentrations. The BFAS dissolution kinetics was slightly faster, as compared to BFS, during subsequent hot curing. Cyanidation test work on the washed synthetic precipitates indicated that the lime consumption of BFAS was three times lower in comparison to BFS, while cyanide consumptions were comparable. Fresh BFS and BFAS precipitates, as well as their cyanidation residues, were found to pass the respective environmental tests in terms of arsenic release.INTRODUCTION Pressure oxidation (POX) is generally viewed as the most appropriate technology for the processing of arsenic-containing refractory gold ores due to the stabilisation of arsenic in the leach residue (Dutrizac & Jambor, 2007; Gomez et al., 2008; Harris, 2003; Collins, Berezowsky, & Weir, 1988). Detailed laboratory studies indicated that several Fe(III)-arsenate type compounds may be formed under typical conditions of autoclave treatment of refractory gold ores (Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2010; Gomez, Becze, Cutler, & Demopoulos, 2011). The basic ferric arsenate sulphate (BFAS) phase (Gomez et al., 2008), also known as Type II ferric arsenate (Swash & Monhemius, 1994) or Phase 3 (Dutrizac & Jambor, 2007), is one of the most common arsenic-bearing products (Harris, 2003; Dutrizac & Jambor, 2007). BFAS precipitation is viewed as one of the best routes for arsenic stabilisation and performed equally well to scorodite during environmental stability tests (Harris, 2003; Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2011)."

Jan 1, 2017

By Gyeonghye Moon, Inhyeok Choi, Jyothi Rajesh Kumar, Jin-Young Lee

"This paper deals with the recovery of the tungsten and vanadium from spent SCR catalyst leach liquors by different hydrometallurgical methods. The first part consists of pressure leaching of spent SCR catalyst using caustic soda followed by metal recovery by liquid-liquid extraction. In a leaching process, the following experimental parameters were tested and optimized: NaOH, particle size of feedstock, temperature, and solid to liquid ratio. The optimum condition for leaching of tungsten and vanadium was under the following conditions: NaOH 3 mol/L, temperature 250°C, particle size <300 µm, and solid to liquid ratio 0.4. From these optimum conditions in this experiment, the dissolution efficiency of vanadium and tungsten was 91.5and 87%, respectively. Liquid-liquid extraction following commercial extractants were tested: TBP, Cyanex 272, D2EHPA, Aliquat 336, Primeme JM-T, Alamine 308, Alamine 304-1, and methyl-tri-octyl-ammonium chloride. The conditions for both valuable metal recoveries were optimized.INTRODUCTIONSelective Catalytic Reduction (SCR) catalyst has become the most effective to reduce nitrogen oxide (NOx) emissions from stationary segments such as power plants and waste incinerations around the world due to the reinforcing regulatory trend and emerging environmental issues (Forzatti, 2001; Spivey, 2002; Li et al., 2011).Currently, the most widely used SCR catalyst is V2O5-WO3/TiO2 system due to its great catalytic properties (Li et al., 2011; Marshneva et al., 1995; Marbergeret al., 2015). In general, the composition of the SCR catalyst used in the stationary application is 0.5 to 1 wt% of V2O5and 7 to 10 wt% of WO3(Marberger et al., 2015; Chen &Yang, 1992, Vuurman et al., 1991; Alemany et al., 1991). Currently spent SCR catalysts are treated as waste and disposed of in landfills. This causes a lot of waste of secondary resources of vanadium and tungsten. In terms of industrial value of vanadium and tungsten (Gupta &Mukherjee, 1990; Moskalyk &Alfantazi, 2003) and reduction of pollutant emissions, it should not be disregarded for their recovery for their material recycling from spent SCR catalyst. However, investigations for recovery of metal values from spent SCR catalyst has been rarely carried out."

Jan 1, 2017

In the last five years, new iron ore pellet plants have been built with significantly reduced air pollution levels compared to the older generation of plants. European and American pollution controls are more stringent that in China and Brazil. The recent American plants have successfully employed circulating fluidized beds for sulfur control, baghouses for particulate control, activated carbon injection for mercury and a new design of specialized low-NOx burners.

Jan 1, 2015

By E. M. Cameron

Reconnaissance radiometric and geochemical data have been obtained for an area on the western shore of Wollaston Lake that includes the Rabbit Lake uranium deposit. The study area is extensively drift cover ed. The geochemical data were obtained by analysis of center-lake sediments and surface waters for a variety of elements and other constituents. The airborne radiometric data comprise measurements of eU, eTh and K obtained with a .50,000-cc NaI (Tl) detector at a mean terrain clearance of 120 m and 5-km flight-line spacing. Uranium in lake sediments and uranium in waters are the most effective geochemical indicators of uranium mineralization; the other elements measured are not notably anomalous. A sample site density of one per 1 8 km 2 is more than adequate for identification of the mineralized area. Because many water samples contain close to or below the current analytical detection limit of 0.05 ppb U, the use of sediments is generally favoured. for broad-scale reconnaissance in the region. Uranium in these lake sediments appears to be little influenced by variations in the organic or iron and manganese content. The most effective radiometric indicator of the mineralization is the eU/eTh ratio. This parameter is less influenced by environmental variation on the ground beneath the flight line than eU alone . The eTh/K ratio is anomalous under the Athabasca Formation unconformity where, in places, the uranium mineralization is localized.

Jan 1, 1977

By S. Kelebek, U. Demir, T. C. H. Richards, E. Koss

"Laboratory-scale tests were carried out to investigate the response of a high-grade (~143 g/tonne) well-liberated gold ore to flotation using two collector types. Octyl and amyl xanthates, representing conventional types of collectors, were tested against an n-octanoic and hexanoic acids under moderate and high redox potential conditions. The latter was based upon a suggestion in literature that monocarboxylic acids are able to adsorb onto the surface of gold at redox potentials near 600 mV (SCE). This investigation did not demonstrate that these carboxylic acids could function as collectors for gold in real ores. In fact, they appear to have slightly depressed gold. However, the results demonstrated that octyl and amyl xanthates acted as highly effective gold collectors for this ore and that an increase in the collector dosage led to an increase in recovery for all mean particle sizes. In some tests, gold recoveries of around 95% were attainable in concentrates with grades around 6 kg/tonne, indicating that xanthate flotation remains a viable means of concentrating gold even at coarse grain sizes. Various aspects of the process such as grade-recovery performance and recovery by size are discussed.INTRODUCTION Three methods are used for the recovery of gold in mineral processing, either alone or in combination: gravity concentration, cyanidation and flotation. Gold occurs as a by-product in some ores together with platinum group metals and as the primary metal in other ores in the form of native gold and electrum, which are alloys of gold, silver and minor amounts of copper. Flotation is a viable method for recovering liberated gold where the gold is visible under an optical microscope (greater than 1 µm in size) and where the attachment of gold grains is not prevented due to bubble loading by competing minerals. It is generally known that grains finer than 150 µm in size will float with most collectors."

Jan 1, 2017

By Xuanxue Mo, Zengqian Hou

"Abstract -Yidun Island Arc in Sanjiang Region is one of the important Kuroko-type volcano­ genic massive sulfide deposits (VMS) districts in southwestern China. Tectonically, the region is situated in the eastern portion of the Tethys orogenic belt, and is a late Triassic extensional island-arc. The island-arc underwent earlier arc construction, intra-arc rifting, later arc construction and back­ arc spreading during its evolution and formed a complete trench-arc-basin system, i.e., the Ganzi­ Litang suture zone, forearc basin, outer arc, intra-arc rifting zone, inner arc and back-arc basin from east to west across the island-arc.Kuroko-type VMS deposits and occurrences discovered so far are limited to within the intra-arc rifting zone of the Yidun Island Arc and tend to occur in groups or clusters distributed in separate fault­ bound basins; e.g., Zengke, Gacun and Xiangcheng basins, in which submarine volcanic rocks, especially bimodal volcanic suites, were extensively developed. The VMS deposits formed in the waning stages of volcanic eruption in the late Triassic and are hosted in the uppermost section of acidic volcanic rocks (rhyolitic-dacitic) within a bimodal suite. The orebodies are associated with these host rocks: rhyolitic-dacitic pyroclastic rocks and exhalites and chemical sedimentary rocks.Ali VMS deposits in Sanjiang are of the Zn-Pb-Cu type. The architecture of the deposits is two­fold, consisting of concordant lenses and layers of massive sulfides and an underlying discordant stockwork. Ali deposits show metal zoning. The hydrothermal alteration related to mineralization is strong and asyrnmetrical, and is found dominantly within the stockwork zone and host rocks surrounding the ores. There are two alteration patterns: (1) chloritization - sericitization - silicification from outer sides to core of the alteration pipe; and (2) silicification + sericitization - silicification + carbonate from the lower to upper part of the alteration pipe_The mineralization temperatures of ore-forming fluids vary in the range 200°C to 335°C. Thermal evolution of the fluids displays temperature profiles that first increase and then decrease with progression of mineralization processes. The majority of black-ore minerais (Groups I and II) formed during intensifying stages of hydrothermal activity, and the majority of serni-yellow-ore minerals (Group III) formed during a thermal maximum . There followed the formation of fine-grained black-ore minerals (Group IV), which interacted with barite layers during decreasing temperature phases.Oxygen and hydrogen isotope studies show that the sources of ore-forming fluids for the Kuroko­ type VMS deposits are two-fold: seawater and magmatic hydrothermal solutions, represented by the Kuroko deposits in Japan and Kuroko-type VMS deposits in Sanjiang, respectively. In the latter case the hydrothermal solutions reacted with host rocks and mixed with cold seawater percolating downward, and circulated through volcanic rocks resulting in development of alteration zones and formation of ore minerals in Kuroko-type VMS deposits."

Jan 1, 1993

By Philippe Caudal

This paper presents a case study in which a slope failure was observed on the west wall of the LAB Chrysotile mine in the vicinity of the main ramp in January 2010. Airborne LiDAR results were used to evaluate slope geometry before and after the failure occurred. Back analysis of the failure was performed to assess rock mass properties at the slope scale using various numerical techniques: limit equilibrium, finite elements and fracture networks. The various approaches correlated well with field observations.

Aug 1, 2013

By Dani J. Alldrick, Alastair J. Sinclair, Colin I. Godwin

"Abstract - The Stewart mining camp has a long history of precious and base metal mining. The camp is abundantly mineralized, with more than 200 widespread, varied, vein prospects, deposits and orebodies. These show wide variations in the mineralogy of ore, gangue and alteration assemblages, and wide variations in textures and structural settings. This report establishes the timing of the different metallogenic epochs and suggests a specific exploration application for systematic lead isotope analyses.Galena lead isotope ratios from a range of mineral occurrences indicate that all these varieddeposits formed during two main mineralizing events. Lead isotope data from the Stewart mining camp do not provide absolute ages for the formation of mineral deposits, but the relative distributions of data are consistent with dates determined in other studies. One ore-forming episode occurred in the Barly Jurassic and the other in the Middle Eocene. Both metallogenic epochs were brief, regional-scale phenomena. Sorne deposits from the younger mineralizing episode were em­ placed adjacent to or superimposed on the older deposits.Field and laboratory studies show that the two metallogenic epochs are characterized by different base and precious metal suites: Barly Jurassic gold-silver-zinc-lead-copper; and Middle Eocene silver-lead-zinc. Therefore, showings of different ages have different base and precious metal potentials and deserve different exploration emphasis. Lead isotope studies provide a reliable, cost-effective method for evaluating the age and commodity potential of small or recently discovered mineral showings and for setting exploration priorities on properties with several varied mineral occurrences . The determination of the age and metal potential of a prospect at an early stage of exploration may govern the urgency, intensity or even the necessity for further exploration work."

Jan 1, 1993

By K. J. K. Weglo, M. U. Savich

"At the Falconbridge Limited, Canadian Nickel Division, Sudbury Operations, we investigated the ""NO NOISE"" ear muffs model NN3-F which is a Swedish product with foam-filled sealing rings (the Hellberg Standard Volume Hearing Protector). It is used extensively at Falconbridge mines in Sudbury.The research which was carried out in the four Falconbridge mines was conducted under three different headings: manufacturer&apos;s attenuation data (psychophysical method), clamping force and head size (bizygomatic diameter), and attenuation tests (physical methods) under working conditions.Manufacturers of hearing protectors claim their products offer noise reductions of 23 decibels (NRR) or more, but they fail to point out that this reduction is obtainable only under ideal conditions. The reality of attenuation under working conditions, as several studies have found, is quite different.Methods for using short measurements to determine the noise exposure index, and for controlling muff-wearing habits, were developed at the Elliot Lake Laboratory. Measurements taken at Falconbridge on ""NO NOISE"" ear muffs revealed that they have a practical attenuation of some IO to 13 decibels. It is important to note here that measurements also revealed that clamping force (thus attenuation) was in an inverse relationship with ear muff comfort. Measuring attenuation using noise dosimeters was a difficult job. Not a single surveyor would accept these measurements (physical method) for absolute accuracy. Apart from that, it was impossible to measure, in one shift, more than two work stations. Because of this, we sought a solution: measuring head size and clamping force in relation to actual attenuations.A detailed analysis of the relationship between attenuation and head size/clamping force was done at four mines. Standard deviation ellipses (standard error ellipses) for head size versus clamping force are in close agreement with measurements that were carried out. In order to measure clamping force an apparatus was constructed and a method for measuring suspension system durability is described in Appendices Band C of this report. At the same time we sought to reduce deterioration of ear muffs in mines as well as to put in place a system whereby attenuation can be controlled and improved. The clamping force apparatus can be operated automatically. The proposed control system is quick, simple and efficient . This system is equally applicable in small and large mining operations, and it can be totally automated and the data computerized for audit of the results. This control system is a new step in controlling ear muff attenuation in working environments.From these measurements of NN3-F ""NO NOISE"" muffs it can be concluded that ear muffs are not the total solution to protect the worker from noise.As the results were evaluated folio wing measurement, Falconbridge switched from the NN3-F ""NO NOISE"" muffs to approximately 90% Mark V ""NO NOISE"" muffs and 10% Mark V MSA muffs. These new muffs showed much better head size versus clamping force relationship and can be expected to produce 14 dBA or better attenuation of noise. RESUMEUne étude des casques antibruit ""NO NOISE"" modèle NN3-F, de fabrication suédoise, avec anneaux d&apos;étanchéité en mousse (dispositif de protection contre le bruit ""Hellberg "" pour volume ordinaire)a été effectuée Ii la Falconbridge Ltd. , Division canadienne du nickel aux installations de Sudbury . Ces casques sont largement utilisés dans les mines de la Falconbridge Ii Sudbury.Cette étude aeu lieuen milieu de travail dans les quatre mines de la Falconbridge sous trois rubriques différentes soit: les données d&apos;atténuation du bruit du fabricant (méthode psychophysique), la force de serrage et la taille de la tète (diamètre bizygomatique), et les essais d’atténuation de bruit (méthodes physiques). Les fabricants de dispositifs de protection contre le bruit prétendent que leurs produits offrent une réduction du bruit s&apos;élevant Ii"

Jan 1, 1986