Search Documents

By CH. Liu, H. X. Jiang, X. Xiao

"A study has been conducted to characterize the fatigue life in 7050-T7451 thick plate by the comparison between an experimental alloy and commercial alloy. The fracture origins were specified and their sizes were measured by scanning electron microscope (SEM). Additionally, the size, number density and spatial distribution of porosity in the experimental material and commercial material were characterized and compared, using X-ray Computed Tomography(XCT). The results showed that microporosity was the predominant site for crack nucleation and subsequent failure of the experimental alloy. However, as for the commercial alloy, fatigue cracks were found to originate from constituent particles. The presence of microporosity in 7050-T7451 thick plate reduced fatigue life of an order of magnitude or more compared to the commercial alloy. The relationships between size of origin and fatigue life were proposed. It was showed that the fatigue endurance was reduced when the size of porosity increased.INTRODUCTION 7xxx series aluminum alloys, due to their combination of high strength, high resistance to stress corrosion cracking, and good fracture toughness, are widely used in structural engineering applications where high-strength and low-density characteristics are fundamental design requirements (Williams& Starke, 2003). Every designer is striving to find an optimal combination of properties including strength, corrosion resistance and fatigue resistance (Wanget al., 2016). Based on the design principles of aircraft, a higher fatigue resistance of aluminum alloys are required. Thus, many investigations have been carried out on the microstructures and its effect on fatigue properties of the 7xxx series aluminum alloy (Robson, 2004; Schubbe, 2009).Microporosity, which is a common defect in casting materials, can lead to a significant deterioration of mechanical performance and fatigue resistance, especially in the high alloyed 7xxx aluminum alloys. The actual valid loading area decreases due to microporosity, which results in detrimental effect on the mechanical properties. Many experimental studies have been conducted in this research field. Mayer et al.(2003) investigated the fatigue properties of magnesium alloys produced by high-pressure die-casting. The results show that porosity in magnesium alloys greater than0.18mm diameter may be considered as the most important material defect for high cycle fatigue and fully reversed loading conditions. Nadot et al.(2004) found that the near surface defects are much more dangerous than the internal defects. Wang et al.(2001a) used the Weibull statistics method to analysis the influence of the microporosity, oxides and particles on the A356-T6 alloy fatigue life. The results show that, the porosity is more detrimental to fatigue life than oxide films and particles. With regard to fatigue resistance, although the deleterious effect of microporosity has been generally acknowledged, a quantitative understanding between casting microporosity and fatigue life in 7050-T7451 plate is not well established."

Jan 1, 2018

By Shen Zhengchang, Dong Ganguo, Chen Dong, Zhang Ming

"It is advantageous to process low grade ores with large scale flotation cells. Large-scale flotation cells have been enhanced with effective volume scale-up. In this paper, the latest and largest flotation cell with effective volume of 680 m3 in China is investigated. The hydrodynamics and flotation kinetics characteristics are conducted using CFD simulation. The similar circulating flow is formed compared to the previous BGRIMM (Beijing General Research Institute of Mining and Metallurgy) flotation cell and it is a suitable fluid dynamics environment. It is demonstrated that the flotation cell produces good gas dispersion and solid suspension. It is indicated that kinetic eddy dissipation plays a key role on collision kernel and collision probability profile. The higher collision probability profile appears at the impeller and stator regions aiding good metallurgical performances. The properties of the large-scale flotation cell are assessed using hydrodynamic numbers. The variation of hydrodynamic numbers such as the power number Np, the Froude number Fr, the air flow number Na, etc with flotation cell volumes show similar properties to previous flotation cells proven to be good in engineering applications. This research would aid structure optimization of the 680 m3 flotation cell.INTRODUCTIONFroth flotation is one of the mains method used in the mineral industry, which is used to process the most of metallic minerals. The proportion of low grade ores has increased with the minerals exploited around world. The increased capacity of concentrators demands large-scale flotation cells. Therefore, flotation equipment has seen a significant increase in size, for which large-scale flotation cells have prominent advantages in improving metallurgical performances, reducing area of plant blueprint printer, lowering the power consumption of the unit ore, decreasing labor cost and overall capital cost. Since the end of 1940’s, flotation cell sizes have continuously increased. To the end of 1990’s, flotation cells with the effective volume of 200 m3 were developed. In the last two decades, flotation cells have achieved a dramatic increase in size. In 2003, an industrial experiment on 257 m3 Smart Cell flotation cells was carried out in Minera Los-Pelambres, Chile. In 2007, the first 300 m3 Tank Cell flotation cell was designed and obtained industrial application in Macraes gold ore, New Zealand. And 320 m3 BGRIMM flotation cells are also in good operation in Toromocho Copper Mine, Peru and Wunugetushan Copper Mine, China. However, flotation cells are conventionally designed using empirically derived relations and geometric similarity. The continual scale-up of flotation cells is still a significant developing process. A 500 m3 Tank Cell was designed for the industrial experiment in Finland and a 620 m3 Tank Cell have also been completed the design. A 660 m3 Super Cell also was manufactured for the industrial experiment released in IMPC 2014. So, the flotation cells with volume exceeding 600 m3 become a pioneering research field for researchers worldwide."

Jan 1, 2016

By P. Hr?enjak

Two groups of methods are usually used in design procedures of underground excavation of dimension stone: the analytical and numerical methods of analysis. In all of these methods the in situ rock mass strength represents the main problem. This is due to massive rocks in dimension stone deposits, consisting of large blocks of rock separated with particular discontinuities, for which the Hoek-Brown empirical criterion, developed for jointed rock masses, cannot be realistically used to estimate rock mass strength, especially for a particular block of rock mass or a particular pillar. On the basis of the regular underground excavation process of dimension stone by separating blocks with the flat jack application, we developed the in situ flexural strength testing method. We carried out numerical analyses and evaluation of uncertainty of measurement in order to validate the in situ flexural strength testing method. On the basis of very good validation results, as well as results of the in situ flexural strength testing of exploitable layers on the ?Kanfanar? quarry, we introduced a new coefficient of reduction, which can be used for correction of other strength parameters determined by laboratory testing for obtaining a realistic value of rock mass strength.

Aug 1, 2013

By C. G. Bruce

"ON NOVEMBER 15th, 1950, the Department of Mines and Technical Surveys announced the discovery of vermiculite near Perth, Ontario. The announcement followed nearly a month of study to determine so far as possible the potentialities of the deposit and quality of the material from surface indications. The mineral was identified by the writer in the field among samples submitted by Mr. Arthur Powers of Stanleyville or, September 22nd, 1950. Within a week of the announcement, mining rights to properties covering a major portion of the deposit had been acquired by commercial interests.Hitherto, Canada has had to import her entire requirements of vermiculite. Prospects of .a domestic supply gave promise of considerable benefit to many industries, particularly the building industry, and to the consumer public. Should the deposit •prove large enough there was also the possibility of exporting to centres in the United States.Field and laboratory studies were continued at the Mines Branch during the winter of 1950-51 as opportunity occurred. It is the purpose of this paper to describe the results of these •preliminary investigations, to attempt to present the Stanleyville occurrence in its proper perspective with regard to similar occurrences elsewhere, and to review the salient features of the vermiculite industry.Properties and UsesVermiculite is a hydrated magnesium aluminum silicate. In appearance it resembles mica, having the same micaceous cleavage, but it differs from that mineral in being very soft, pliable, and inelastic. Colours range from black through dark olive-green and brown to almost colourless."

Jan 1, 1952

By Jamie Archibald

The Department of Mining Engineering at Queen?s University conducted a study of backfill practices in underground mines across Canada to assess the current state of backfill usage and to overview potential hazards associated with backfill practice, from preparation to transportation to placement. The primary aim of this study was to cover each component of a typical mine backfill system, and to identify potential incidents leading to the disruption of backfilling operations and any associated corrective actions. This paper, Part II of the study, deals with underground operations consisting of backfill transportation and backfill placement. Part I of the study, which deals with surface operations consisting of backfill material supply and backfill plant preparation, is also presented in these proceedings. A review of safety measures associated with current backfill operations and recommendations for procedures of best practice that should be implemented to reduce fill-related hazards in all mine backfill workplace environments are presented. In general it has been found that system failures normally lead only to minor losses to the operations.

May 1, 2009

By M. Rafieazad, P. Fathi, M. Mohammadi, A. M. Nasiri

This study examines the impact of low-temperature heat-treatment cycles on microstructure and corrosion performance of Direct Metal Laser Sintered (DMLS) AlSi10Mg_200C alloy. It is known that the morphology and the size of eutectic silicon are the two most critical factors affecting mechanical properties of the AlSi10Mg alloy. Although high-temperature heat-treatment cycles are common practice for the strengthening of the cast Al-Si-Mg alloys, in the case of DMLS fabricated AlSi10Mg alloy, high-temperature solutionizing and low temperature annealing cycles result in mechanical properties degradation primarily due to a dramatic decrease in the solubility of Si in the super-saturated a-Al matrix of the as-printed alloy. In this study, low-temperature heat-treatment cycles that only promote precipitation of Mg2Si accompanied by the interruption of the silicon network were investigated. SEM and XRD analysis were utilized to observe the evolution of microstructure after different annealing heat-treatments at 200, 250, 300, and 350°C for 3 h. Increasing the heat-treatment temperature contributed to the Si networks interruption and an increased precipitation of Mg2Si phase. Low-temperature annealing from 200 to 350°C was found to promote the homogeneity of the microstructure characterized by a uniform distribution of eutectic Si in ??-Al matrix. Additionally, in order to investigate the impact of different heat-treatment cycles on corrosion resistivity of DMLS-AlSi10Mg_200C, the potentiodynamic polarization testing and electrochemical impedance spectroscopy were performed in a 3.5 wt.% NaCl solution. The results revealed more uniformly distributed pitting attack on the corroded surface by further increase in the annealing temperature, which was attributed to the uniformity of Si dispersion. In comparison, low temperature annealing at 200°C led to a penetrating selective corrosion attack along the melt pool boundaries, resulting in a higher corrosion rate associated with the lower absolute value of impedance of the protective passive film on the surface.

Jan 1, 2018

By G. F. Cross

INTRODUCTION THE electrical system associated with the mining development of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, may be conveniently divided into three main parts, namely, the Island Falls power plant, the transmission line, and the distribution systems at the mine and metallurgical plants. For a description of the Island Falls power plant and the transmission line, the reader is referred to the paper, to be presented at this meeting, by R. W. Davis and M.F. Huffaker (1). The transmission line and sectionalizing combinations are shown diagrammatically in Figure 1. The present paper deals with the distribution systems at the Flin Flon mine and metallurgical plants. THE FLIN FLON DISTRIBUTION SYSTEM In the high-tension sub-station at Flin Flon, each incoming 110 kv. line is provided with manually operated, gang-type disconnecting switches. Each line is connected to Canadian General Electric type F.H.K. 39-60B-F.2 T.P.S.T. 110 kv. 400 amp. oil circuit breakers, each provided with M.K.4 centrifugal motor-operated closing mechanism. Gang-type disconnecting switches are installed on each side of incoming line breakers, and a complete ring bus system is formed through station tie breaker, which is' further provided with gang-type disconnecting switches on either side. The?bus tie breaker is of Canadian Westinghouse design, type G.22B, 110 kv., 400-amp., solenoid-operated. All three breakers are provided with bushing-type current transformers, and the two line breakers are further equipped with bushing-type potential devices. Oxide film lightning arresters (121 kv.) are installed on each incoming line and are located outside the station. Each line is further provided with interlocked gang-operated ground disconnecting switches. All disconnecting switches are mechanically connected to auxiliary switches, which provide pilot service to indicating lamps in the remote-control room, located in a separate building.

Jan 1, 1935

By N. Saeidi

"For a mine section comprising 100 different stoping activities, there are ~10158 different possible stoping sequences to explore in the mine schedule optimization search and this figure is indicative of the challenge posed in maximising profitability through mine schedule optimization. Any viable excavation timetable must satisfy all conditions that will constrain feasible sequences. In general, consideration of additional constraint will tend to reduce profitability. Geomechanical constraints on mine schedules, introduced with the aim of avoiding excavation instabilities, can be established for underground mine schedule optimization processes but, currently, this is done only rather crudely; precedence relations between excavation activities (stoping or development) are encoded to produce particular stope sequence patterns (e.g. ‘chevron’ or pyramidal sequences).The work reported aimed to investigate automated processes for formulation of such geomechanical constraints. The timetable optimization approach to the problem precipitated a fresh look at time dependent, and excavation sequence dependent, deformation. Abundant evidence emerged that supported the notion that any methodology developed that failed to account for such time and sequence dependencies was itself bound to failure. Yet, it was also recognised that any deviation at all from an assumption of linear elasticity for geomechanical numerical modeling, adopted to inform geomechanical constraint formulation, would rapidly lead to impractical levels of computational effort.Thus the approach presented here represents a compromise: the elastic stress fields induced by individual mining activities are computed for each activity, independently considered within a computational domain identical to that of all other activities. These are stored in a database. Instability risk for a specific sequence of mine activities can be assessed through superimposition of stress fields drawn from the pre-computed database. Time stamps allocated to events corresponding to the excavation processes permit the conversion of the sequence of elastic stress fields into a time table of stress fields. For specific locations within the computational domain, the aggregate effect of the sequence of mine activities leads to stress-time histories having a castellated appearance, a result of the near instantaneous response of an elastic medium to the excavation perturbations. Time dependent deformation responses are crudely allowed for through the re-profiling these castellated histories through graphical construction of curved responses, where the curve gradients are related to a viscous parameter. Such curves form the basis for a geomechanical constraint formulation to be adopted for mine schedule optimization."

Jan 1, 2015

By Alexander Smith

"The Silver Standard mine is 6 miles by road northwest of New Hazelton, B.C., a small town on the northern line of the Canadian National Railways some l 75 miles northeast of Prince Rupert. The deposits lie on the western slope of Glen Mountain (elevation 2,100 feet), with the main adit, mill, and campsite at 1,300 feet. The deposits were found in 1910, shortly after the area had been swept by forest fire and during a period of prospecting activity spurred by the construction of the railway. Crude ore only was shipped until 1918, when a 50-ton gravity mill was built which operated until 1922. Gross value of production of this period, at present metal prices, was about $1,000,000.In 1947 the present company was formed and a 50-ton flotation mill installed. Production from 1948 to 1955 has been in excess of $10,000,000, and net smelter returns about two-thirds of this amount. More than 60 per cent of the production and 80 per cent of the profit have come from one vein, No. 6. On the 1,300-foot level this vein had an ore section 375 feet long and 2.5 feet wide, averaging 0.18 ounces gold, 85 ounces silver, 10 per cent lead, and 16 per cent zinc.The mine workings follow a simple pattern. A series of parallel veins, striking northeast and dipping southeast, are numbered from 0 to 12, starting at the northwest. They lie within a zone trending south 70 degrees east, and the distance between Nos. 0 and 12 veins is about one mile. Recently several cross-veins, dipping northeast, have been found between Nos. 8 and 12. They are apparently of the same type as the others, though they may not have the same structural controls. They could be an important new source of ore.The mine has been developed principally by crosscut adits at the 1,500- and 1,300-foot levels and a 510-foot shaft with levels at I, 150, 1,000, ·and 850 feet. Drifts and crosscuts total 17,000 feet, chiefly on Nos. I, 4, 6, 7, and 8 veins. The drifts are stoped by shrinkage, top shrinkage rill, cut-and-fill with resuing, or open stope methods. The mill produces a lead-silver-gold-copper concentrate and a zinc concentrate, with indicated recovery of more than 96 per cent (4)."

Jan 1, 1949

By R. T. Jones

"Technical publications in the field of mining and metallurgy have existed for a long time. Recent developments in electronic publishing on websites make it possible to disseminate information more widely and cost effectively than before. Professional societies have an opportunity to serve their members and their industry by publishing high-quality peer-reviewed papers on their websites as well as in printed form. Older publications can be scanned, and optical character recognition can be used to provide searchable text. Various business models exist around this process. This paper outlines the approach used by the Southern African Institute of Mining and Metallurgy (SAIMM) to provide free open access to their journal papers and conference proceedings, as well as the work being done by OneMine.org to collect technical papers from a number of international societies and make them available to subscribers via a large database. An approach is outlined that should be of benefit to authors, readers, and society at large.INTRODUCTIONGeorgius Agricola (1494-1555) was not the first writer on the subjects of mining and metallurgy, but is well known as the author of De Re Metallica (‘of things metallic’ or ‘on the nature of metals’), a book that documents and illustrates the observations he made in the course of his extensive travels in the 1500s. Agricola wrote extensively about mining methods and metallurgical processes that were in place in the Middle Ages. The original Latin version of De Re Metallica was published in 1556, the year after Agricola died. It was translated into English by Herbert Hoover, a mining engineer and later President of the United States, and his wife Lou Henry Hoover, a geologist and classicist. The English version of De Re Metallica was published in 1912."

Jan 1, 2012

By Robert B. Parsons

"New tax rules that can apply to the repayment, extinguishment, or other settlement of a company's debt are finally taking shape. These new rules are far-reaching in their application, and can affect mining companies in a serious, negative way.IntroductionIn his February 1994 budget, Finance Minister Paul Martin announced changes to the Income Tax Act that could have an adverse impact on a company that restructures its debt. Since then, the new rules have undergone considerable transformation during their fetal stage: draft legislation was introduced in July 1994; revised draft legislation was introduced December 1994; and a third version of draft legislation was introduced February 1995. It seems that the new rules have now been pretty well finalized, and they contain some serious traps that the unwary could fall into. The new rules are of particular importance to mining companies, because a mining company's resource pools will be caught under the new rules, whereas these pools escaped the wrath of the old rules. The following commentary summarizes the new rules that are generally referred to as the ""debt forgiveness"" rules."

Jan 1, 1995

By Baisheng Nie

The process of gas diffusion through coal particles and the mathematical physical model under the third kind boundary condition was determined to obtain the rules of gas diffusion through coal particles of different sizes. The analytical solution of the equation was obtained by the Method of Mathematical Physics. The parameters of analytical solutions and the implications of parameters were analyzed. The Biot criterion (Bi) and the Fourier criterion (F0) of mass transfer can represent and reflect the features of gas diffusion field of coal particles. Moreover, the measurement method of gas diffusion coefficient and surface mass transfer coefficient is introduced and an example of measurement is given. The achievement can provide the support to prevent disasters related to methane in coal mines.

Aug 1, 2013

"At the May 15, 2006 and the May 1, 2007 Canadian Securities Administrators (CSA) Canadian Institute of Mining, Metallurgy and Petroleum (CIM) meetings in Vancouver and Montreal, CSA requested CIM consider certain issues arising out of the CSA review of Technical Reports and public disclosure, in general, regarding the practice of estimation and reporting of Mineral Resources and Mineral Reserves. The following is a summary of the issues raised by the CSA and the responses of the CIM.Preamble: At the May 15, 2006 and the May 1, 2007 Canadian Securities Administrators (CSA)-Canadian Institute of Mining, Metallurgy and Petroleum (CIM) meetings in Vancouver and Montreal, CSA requested CIM consider certain issues arising out of the CSA review of Technical Reports and public disclosure, in general, regarding the practice of estimation and reporting of Mineral Resources and Mineral Reserves. The following is a summary of the issues raised by the CSA and the responses of the CIM Reserve Definition and the CIM Estimation Best Practices Committees (the Committees). This information is intended to provide the Qualified Person (QP) with further guidance when estimating Mineral Resources and Mineral Reserves and in preparing a technical report written under National Instrument 43-101 (NI 43-101). Several members of the CIM Reserve Definition Committee, the CIM Estimation Best Practices Committee and some members of the Committee for Mineral Resources International Reporting Standards have reviewed these issues and provide the following commentary.Issue 1. - CSA requested CIM review and comment on the selection of an appropriate commodity price to be used in Mineral Resources and Mineral Reserves estimates.Commodity prices are used in the estimation of Mineral Resources and Mineral Reserves and in the economic analysis of a property. In times of rapidly changing commodity prices, or when prices are at the extreme ends of a commodity price cycle, the QP has a difficult job in selecting an appropriate commodity price.• The selection of appropriate technical variables, including commodity price, is clearly the responsibility of the Qualified Person (QP). The QP must describe the reasons for selecting these variables, including price, in the technical report.• The definition of a ""Mineral Resource"" contains the wording ""reasonable prospects for economic extraction,"" therefore, a QP must select economic parameters, including commodity price, that will result in an estimate of Mineral Resources and Mineral Reserves that have ""reasonable prospects for economic extraction""."

Jan 1, 2003

By A. Farzanegan, D. A. Lowther, A. R. Laplante

"Off-line optimization studies are often necessary to improve the efficiency of grinding circuits. These studies are primarily based on the mathematical modelling of processing units (e.g., ball mills and hydrocyclones) and computer simulations. To complete an optimization task, process engineers must possess skills and knowledge of different subtasks involved in such efforts, e.g., plant audit, laboratory tests, and data analysis. Such know-how can be in part provided by Knowledge-Based Systems (KBSs). One such system, being developed in C Language Integrated Production System (CLIPS), is presented here, with focus on the estimation of ball mill selection functions for the purpose of both diagnostic and simulation, and its use for the optimization of ball size. Some of the interpretation and diagnostic rules will be presented, as well as grinding kinetics and classification data likely to fire them.IntroductionSince the late eighties there has been a growing trend in applying Knowledge-Based Systems (KBSs) to mineral processing [Meech 1990, Bearman and Milne 1992). Table l lists some KBS (often referred to as expert systems) applications that have been used mainly as tools for improving on-line monitoring and control of grinding circuits. However, there has been fewer attempts to add the symbolic processing powers of KBSs to conventional off-line grinding simulators. Figure 1 shows a relatively standard procedure to perform an off-line optimization study [Napier-Munn and Lynch 1992]. In brief, a typical program includes taking representative samples from a number of streams, running laboratory tests on collected samples, estimating model parameters which describe physical processing units (e.g. ball mills and hydrocyclones) validating model predictions and using models for simulation trials. One inevitably needs to be familiar with concepts of process modelling and simulation as well as various computer programs to be able to complete all steps of the study. Much of this ""expertise"" can be captured by KBSs, given their inherent capabilities for symbolic knowledge representation and manipulation."

Jan 1, 1997

By R. K. Rajamani

Discrete Element Method simulation of charge motion in ball, SAG and autogenous mills has become a standard for design of mill internals, power draft evaluation, etc. Both two-dimensional and three-dimensional codes are being used. The two-dimensional code dominates the user market since the code completes a simulation in one or two hours. On the other hand, three-dimensional codes have been in the domain of specialists who can handle the complexity of the code and have access to parallel computing hardware. For the first time, this barrier is overcome via computing with graphic processing units (GPU). Commodity graphics cards now allow parallel computation with hundreds of processors. It is shown that the computational time has been reduced by a factor of fifty using GPU computing. Hence, SAG charge simulation results in three dimensions are achievable in a few hours using affordable desktop machines. The GPU computing shown here enables the three dimensional simulation into a manageable daily task for mill designers and researchers. On the technical side, the simulations can be elevated to a higher level of complexity to simulate breakage and transport. First, the speedup factor of fifty is established for the Nvidia GeForce GTX 580 graphics card. Next, four simulation tasks, consisting of AG, SAG and ball mills are reported. The simulation of AG and SAG mills are completed in less than 8 hours. The ball mill simulation with 1.25 million spheres is completed in 27 hours. In the near future, as the graphic card hardware advances the compute time can be halved.

Jan 1, 2012

By Robert Strachanm

The East Kootenay coal-field, situated close to the boundary between the provinces of Alberta and British Columbia, is composed of four small areas locally called the Crow's Nest Pass, the Upper Elk, the Flathead and Crown Mountain, and comprises an area of about 3 78 square miles. From eleven to twenty-five seams have been exposed of two feet and over in thickness, with a total thickness of about 200 feet of coal, and reckoning about one hundred feet to be workable, gives an estimate of coal available of about thirty-seven billion tons. The coal is a high-grade bituminous, occasionally tending towards anthracite, and the majority of the seams furnish a. very good quality of coking coal as well as an excellent steam coal. The coal-field is found in the mountain ranges in long narrow strips. The age of the fonnation and the thickness of the covering beds have had considerable influence on the character of the coal, and lateral pressure and disturbances in the process of mountain-building have wrought great changes. With such an abundance of coal, it has been a disappointment that the East Kootenay field has not figured larger industrially. So far only one portion of the coal-field has been utilized. This is the Crow's Nest, where, in 1898, the Crow's Nest Pass Coal Company commenced development. Access to the coal seams was easily obtained, the mountain creeks having eroded away the covering, and mines were driven into the coal seams. In that year about ten thousand tons of coal were produced from the mine at Coal Creek.

Jan 1, 1924

By Arthur L. de Carle

"IntroductionThe Key Lake uranium-nickel deposits are located within a Mineral Lease centred at latitude 57 ° 12' north and longitude 105 °39' west along the southeastern rim of the Athabasca sedimentary basin in northern Saskatchewan, approximately 240 km north of La Ronge (Fig. 1). Access is provided by an allweather provincial highway from Pinchousc, situated about 200 km to the south, and a private airstrip maintained at the mincsitc.These deposits have been developed by Key Lake Mining Corporation on behalf of the Saskatchewan Uranium Joint Venture. Participants in the joint venture include Saskatchewan Mining Development Corporation (50%), Urancrz Exploration and Mining Limited (33 1/3 %) and Eldor Resources Limited (16 2/3 %).Considerable geological work has been conducted on the Key Lake orebodies and reported in summary papers published by Dahlkamp and Thn, (1977), Dahlkamp, (1978), Gatzweiler eta/., (1979) and Kirchner el a/. , (1980). However, intensive geological research is ongoing, particularly since many problems regarding ore genesis and controls remain unresolved . Exploration History and DevelopmentThe events (Gatzweiler eta/., 1980) which led to the discovery of the Key Lake ore bodies began in the summer of 1971 by following up on the reports of airborne radiometric anomalies and anomalous radon values in the Zimmer Lake water situated approximately 5 km to 6 km to the southwest. This work succeeded in locating a few high-grade uranium and nickel-bearing boulders associated with esker material. An integrated program, consisting of various geochemical and geophysical surveys along with diamond drilling, culminated in the discovery of the Gaertner orebody during July 1975. Subsequent fence drilling across the strike extensions of this ore structure located the Deilmann deposit, approximately I km to the northeast, in June 1976"

Jan 1, 1986

By W. B. Coker

A helicopter-mounted lake-sediment and lake-water survey was carried out over Grenville rooks in the Renfrew area (parts of Renfrew and Lanark counties) during four days of October, 1975. In the course of this survey. 1150 square kilometers were covered, with 246 lake-sediment and 276 lake -water samples collected from every body of water on which the helicopter could land. Sample sites, which averaged one per 4.6 square kilometers, included lakes, ponds, beaver ponds, swamps and marshes. Lake-sediment samples were taken using a G.S.C. sampler. Waters were collected directly into polyethylene bottles. At each sample site , surface and bottom-water pH, dissolved oxygen content, conductivity and temperature were measured using a Martel. Water Quality Analyzer. The lake sediments were air dried and then ball milled to pass a minus 80-mesh sieve. Lake sediments were analyzed for U by delayed neutron activation and for Mo, Cu, Zn, Pb, Fe, Mn, Ni and Co by atomic absorption techniques. The organic content of the sediments was determined by loss on ignition at 450 °C. Lake waters were acidified with nitric acid on the day of collection. The U content of the water s was determined by fluorometry; the Cu, Zn, Pb, Fe, Mn , Ni and Co contents of the waters were determined by solvent extraction - atomic absorption techniques. A close relationship was found between bodies of granitic, syenitic and pegmatitic bedrock and elevated U levels in the lake sediments. The Hurd Lake and White Lake granitic intrusive were encompassed by an annulus of higher U activity. Field inspection revealed that the U concentrations occur within a zone which may represent a contact metamorphic aureole. Within these complexes, anomalous concentrations of U appear to be associated with Mo. Information derived from the lake-water data reinforces the geochemical distributions outlined by the lake-sediment survey . This survey was carried out in order to develop optimum sampling and analytical procedures for geochemical reconnaissance of the Grenville Province that may be carried out under the auspices of the Uranium Reconnaissance Program.

Jan 1, 1977

By I. S. Thompson

"Exploration properties form a continuum from grass roots to those with favourable geology, geochemical and/or geophysical anomalies, mineralization, showings (prospects), and finally to those with defined mineral deposits. Often, properties exhibit a composite of these categories.The most problematic to value are properties or deposits that are not economically exploitable at the time of the valuation due to a lack of exploration, insufficient grade or tonnage, poor mining conditions, or the imposition of socio-economic, environmental, or legal constraints.Various acceptable methods of valuing the range of all such mineral properties or deposits are reviewed. Some less appropriate methods are also discussed."

Jan 1, 2002

By David G. Meadows

During the last decade Antofagasta Minerals? Los Pelambres Mine has dramatically increased its ore throughput following the fast initial phase ramp up through a series of planned incremental expansions. The original 85,000 mtpd, two SAG line plant was commissioned in 1999 and rapidly exceeded nameplate tonnage in only a few months. Following this, the inclusion of a pebble crushing circuit resulted in throughputs in excess of 114,000 mtpd and a recent, final third line SAG and ball mill addition have taken the plant to over 175,000 mtpd even with increasing ore hardness and changing ore feed characteristics. The progressive changes are described in this paper together with how the technical challenges have been met.

Jan 1, 2012