Search Documents

By K. Ohto, B. B. Acihikari, H. Kawakita, M. Gurung, S. Alam

Two kinds of adsorbents were prepared from persimmon tannin extract to investigate their adsorption behavior of metal ions from hydrochloric acid solution; one was prepared by treating with concentrated sulfuric acid while another was prepared by immobilizing functional groups of quaternary amine. The former adsorbed only gold(III) and its maximum adsorption capacities was evaluated as high as 1510 g/kg while the latter adsorbed not only gold(III) but also palladium(II) and platinum(IV), the maximum adsorption capacities of which were evaluated as 820, 89 and 101 g/kg, respectively. For both adsorbents, practical adsorption of base metals was not observed.

Jan 1, 2011

By A. G. Lylie

Introduction At the Britannia Mining and Smelting Company's mill, the equivalent of 2,500 to 2,800 pounds of copper sulphate crystals per day is made from copper which is precipitated from the mine-water. This copper sulphate is used in the mill for the recovery of sphalerite by2 flotation. From 1932 until 1936 it was produced by exposing the precipitate to air for thirty days and then dissolving the oxidized copper with dilute sulphuric acid. In 1936, the flotation of sphalerite was discontinued and, when it was resumed in 1947, steps were taken to try to improve the former method. The present paper outlines the way in which this was done, and describes the plant and procedure by which copper sulphate is now being made, and by means of which an appreciable saving is being effected. Aboratory Tests The previous work had established that the precipitate, which consists mainly of metallic copper, must be oxidized before the copper would dissolve in dilute sulphuric acid. Various methods for oxidizing it were tried but in the early laboratory work the only suitable one found was to heat the precipitate to 600°C. and hold it at this temperature for two hours. When this was done, approximately 90 per cent of the copper became soluble in .acid. This percentage was considered satisfactory for practical purposes, but the cost of roasting was prohibitive because only a small amount of roasted precipitate was required each day.

Jan 1, 1951

By G. M. Card, K. D. Card, B. V. Sanford

Abstract-The Canadian Shield and its extensions are traversed by an orthogonal system of northwest and northeast trending arch-style uplifts. These basement arches were formed by repeated vertical movements along pre-existing structures during compressional and extensional tectonism connected with events in surrounding Proterozoic and Phanerozoic orogens and ocean basins. The arches influenced patterns of sedimentation and tectonism in the intervening epicratonic basins and marginal platforms throughout the Proterozoic and Phanerozoic. Movements on the arch structures also triggered minor magmatism and controlled the location and timing of alkalic rock-carbonatite, kimberlite, and related intrusions in the Canadian Shield, the Western Canada Sedimentary Basin, and West Greenland.

Jan 1, 1997

By F. H. Wheeler

CONSIDERING the nature of this audience, I perhaps, in addressing you on the subject of air transportation as related to the mining industry, should speak with tongue in check or at least with some reservation. I know full well that many of you, veterans in the great mineral development in Canada, are perhaps more conversant with the overall aviation picture than I, for aviation to you has been the means to an end, and in many instances has been part and ?parcel in the success of your particular projects, in the form of the initial means of transport. I feel, however, that we in this room today have somewhat parallel geographic interests - yours in relation to what is in the ground, mine in the air - and also in the forests and in the streams - aviation, hunting, and fishing - things which have occupied my attention practically all my adult years. In the light of what has gone. before, and in view of present developments, I think you will agree with me when I say that I do not think there could be a more intriguing pursuit than playing a hand in rolling back Canada's tremendous northern frontiers, even if, at this stage, we have made but slight impression on the untold opportunities which lie in our wide-spread, undeveloped areas.

Jan 1, 1956

By Ralph V. Stewart

"The asbestos orebody is contained within ultrabasic rocks of Precambrian age, being located in the continuous permafrost zone of the Quebec Ungava Peninsula, some 300 miles north of the tree line at approximate latitude 61'49' and longitude 73°58'.The asbestos deposit is at the western tip of a folded ultrabasic sill complex which trends northeast and covers an elliptical area 4.5 miles wide by 15 miles long. Locally. the asbestos occurs in. a completely serpentinized dunite rock. The principal rock types in the vicinity of the ore-body originally consisted of dunite, peridotite and pyroxenite, all of which have experienced at least two periods of alteration, so that no fresh rock now remains.The main ore zone in the open pit is approximately one quarter mile in length, 150 to 200 feet in width, and plunges at 25 to 30 degrees in a northeast direction below surface, to a vertical depth of at least 1,200 feet, Consider¬able tectonic activity resulted in favourable structural conditions which culminated in the formation of the ore zone in its present form.The deposit consists principally of cross-fibre ""gash type"" veins which vary in length from several inches to several feet. The principal fibre vein direction is parallel to the dip of the enclosing serpentinized dunite and sill complex.Some of the problems encountered during diamond drill¬ing in permafrost are briefly discussed."

Jan 1, 1976

By G. M. Card, K. D. Card, B. V. Sanford

The Canadian Shield and its extensions are traversed by an orthogonal system of north-west and northeast trending arch-style uplifts. These basement arches were formed by repeated vertical movements along pre-existing structures during compressional and extensional tectonism connected with events in surrounding Proterozoic and Phanerozoic orogens and ocean basins. The arches in?uenced patterns of sedimentation and tectonism in the intervening epicratonic basins andmarginal platforms throughout the Proterozoic and Phanerozoic. Movements on the arch structuresalso triggered minor magmatism and controlled the location and timing of alkalic rock-carbonatite, kimberlite, and related intrusions in the Canadian Shield, the Western Canada Sedimentary Basin, and West Greenland.

Jan 1, 1997

By M. Samuels

"Block and panel cave mining methods are being increasingly proposed as they allow massive, deeply situated ore-bodies to be mined economically at a time when discovery rates of significant near surface deposits are declining. Cave-to-Mill, a mine-to-mill approach for block cave mines, defines ore block models with respect to both mine and mill performance. A cave-to-mill study for the New Afton block caving operation focused on identifying value opportunities related to fragmentation and sorting for a future lift as development progresses deeper. The lack of selectivity and potential for dilution associated with the block cave mining method results in many caving operations having to mine and either dispose of or process material that is below cut-off grade at certain stages of production. As an outcome of the study, the variation in cave fragmentation size and the sensitivity of mill throughput to feed size was examined. To evaluate the amenability of bulk and particle sorting, Prompt Gamma Neutron Activation Analysis and X-Ray Fluorescence sensors were tested. A conceptual bulk and particle sorting flowsheet is presented. Grade data from regular underground sampling was used to predict the performance of a bulk sorter. A heterogeneity analysis of material reporting to drawpoints helped to identify areas of the extraction level that experience high variations in grade and thereby stand to benefit from dedicated ore and waste material handling systems should underground bulk sorting be implemented.INTRODUCTION Block and panel caving are low-cost underground mass mining methods that are suitable for excavating weak, massive and steeply-dipping orebodies. Accordingly, cave mining methods have predominantly been used to mine copper porphyry and diamond bearing deposits. Due to the increasing depletion of near-surface orebodies, it is expected that block and panel caving methods will be increasingly used in the copper-gold industry. Their implementation holds significant potential to extend the life of existing open-pit operations by providing an economic means to access ore located at depths that are beyond the practical limits of open-pit mining. Examples of cave mines proposed for British Columbia include the Kwanika Mine, Red Chris underground, Kemess Underground project, and the Iron Cap and Mitchell cave mines of the Kerr-Sulphurets and Mitchell (KSM) project (Moose Mountain Technical Services, 2017; Imperial Metals, 2017; Golder Associates, 2017; Tetra Tech, 2016)."

Jan 1, 2018

By J R. Barber, B. E. Rogers, R. Fukuzawa

Mercury is sometimes present in non-ferrous ores including gold, zinc, copper and lead. The selection and use of appropriate mercury abatement technology is critical for preventing its release to the environment during ore processing and to protect workers from mercury exposure. This paper presents a general decision-making process for mercury abatement technology selection for major emission sources in the gold industry. Mercury abatement can be accomplished through making process changes and/or by adding a process step to an existing system (i.e. "end-of-pipe control"). Advantages and limitations of the technologies along with waste / by-product management options are discussed through case studies of current operating mercury abatement systems.

Jan 1, 2015

By J. F. Harkom

Introduction The importance of the preservative treatment of mine timbers need scarcely be stressed here. Increasing the life of mine timbers will reduce one of the major costs of mining and also conserve the available timber supply which lies within easy access of the mines. When treated, several species of timber may be used which otherwise could not be considered, owing to their short life. Another feature which should appeal to the mining industry is that wood preservatives are a mine product, and the benefit to be derived from the increased consumption of wood preservatives due to the example set by mine owners is not inconsiderable. Mine timbers may be divided into three classes when considering preservative treatments. (1) Timber obviously not profitable to treat owing to long natural life or short period of time in service. (2) Timber that obviously should receive protection from decay. (3) Timber installed in locations where the length of service required will depend on future developments, so that preservative treatments might or might not prove to be a profitable investment.

Jan 1, 1930

By Alice H. Zhu

Belt conveyors are widely used in materials handling industries. The bulk materials which can be transported include ores, coal, earth, grain, limestone, wood chips, fertilizer components such as potash and many others. Along with the new technology development and enhanced industrial automation requirements, belt conveyor instrumentation has also been modernized to improve conveyor availability and performance. Traditionally, belt conveyors are equipped with emergency pull cord switches to shut the conveyor down, misalignment switches to signal the belt offline condition, speed sensors to detect the belt slippage, and level switches to prevent material plugging in the discharge chute. Belt rip detectors are also normally provided for long belt conveyors. As a rule, equipment condition monitoring is not automated at most operating facilities, but is performed manually by maintenance staff via time-based surveillance. The new generation of condition monitoring instrumentation and control equipment can be successfully utilized to design a reliable, cost-effective, and centralized monitoring system, capable of monitoring a wide variety of mechanical equipment. The implementation of the condition monitoring automated system can provide continual monitoring of the plant equipment to ensure safe operation of the equipment to its required capacity. Any abnormal behavior of the motors, gear reducers and pulleys can be analyzed, alarmed, and recorded immediately, so problems can be detected and resolved before critical components failure. Therefore, the current trend is to provide the belt conveyors with condition monitoring system in addition to the traditional instrumentation, where temperature probes and vibration sensors can be installed on motors, gear reducers and all pulleys. Another innovative development is a three-in-one type belt rip detector which combines laser, tray and cord type detection together to ensure a prompt belt tear indication. The purpose of this paper is to present the latest development of belt conveyor instrumentation and introduce the application of newly developed instruments.

Nov 1, 2011

By M. Boodman, E. Gertner

"At first glance, the activities related to mining and mineral exploration appear to be local or domestic, rather than international, in nature. Minerals, as corporeal or tangible property, form an integral part of the land in which they are found until extracted and exploited commercially. Even in the latter phase, the tangible nature of minerals gives the impression that the law governing the commercialization of minerals is the law of their situs at any given time. The nature of minerals appears to negate the international aspect of mineral enterprises.The fundamental flaw in the above analysis is its focus upon the nature of minerals, rather than the role of persons in mineral enterprises. The high costs of mineral exploration and commercialization invariably require the involvement of international consortiums or joint ventures. Governments may not have access to the funds necessary to exploit the mineral resources that they control. Local or domestic enterprises may not have sufficient expertise for mineral exploration. Further, markets for various types of minerals are far from localized or static. For these and other reasons, the tangible and localized nature of minerals belies the fundamentally international nature of mineral exploration and commercialization."

Jan 1, 2004

By J. E. Zajic, E. A. Sullivan, T. R. Jack

"The release of vanadium, iron, nickel and titanium from the cokes produced in the upgrading of Alberta oil sands bitumen has been assessed for simple chemical leaching processes. Flexicoker coke (Exxon Engineering and Research) has been found to be quite amenable to the recovery of vanadium as well as nickel, iron and some titanium by these techniques, whereas fluid coker coke (Syncrude) and delayed coker coke (Great Canadian Oil Sands) are relatively intractable under the mild conditions employed. The factors affecting the extent of vanadium release are discussed in terms of the surface area accessible, the wettability of the material, and the chemical and physical composition of the coke particles in each case.A novel biologically assisted heap leaching procedure for f1exicoker coke is also described, based on the growth of the chemolithotrophic bacteria, Thiobacillus thiooxidans A TCC 8085, on elemental sulphur added to the coke."

Jan 1, 1980

By François Robert

The rate of new mineral discoveries in Canada has been declining in the last two decades. In response to the challenge and to stagnating investments in mining-related R&D, twenty Industry partners, supported by PDAC and Natural Resources Canada, established in 2010 the Exploration Innovation Consortium (EIC). This Consortium seeks to promote the discovery of new resources in Canada through coordination and sponsorship of industry-focused innovative and collaborative research and technology development, as well as training and education in mineral exploration. The two main themes of the integrated R&D program focus on exploration targeting in Deep and Mature Environments and in Remote and Covered Terranes.

May 1, 2011

By Xiaoqiong Wang, Daobing Wang, Fanbao Meng, Jianbo Wang, Hongkui Ge

"Shale gas has become an important unconventional oil and gas resources. Its effective development relies on comprehensive and accurate understanding of shale gas reservoirs. Rock mechanical properties is one of the important components of reservoir evaluation. Two adjacent black shale samples, which are cored from the depth of 1145 meters in Chongqing, southwest China, are subjected to acoustic emission(AE) test under uniaxial stress and compared with coarse grained granite. The results of synchronous AE, stress-strain and ultrasonic velocity experiments show that shale has weak anisotropy. Compared with granite sample, two shale samples are similar, but their strength, velocity and brittleness are quite different, indicating that shale has strong microscopic heterogeneity. TOC, XRD, SEM microstructure analysis show that total organic content, mineral composition and natural fractures are the main impacting factors for mechanical heterogeneity. INTRODUCTIONShale gas is a typical low-grade marginal resource, which is characterized by ultra-low matrix permeability and small single well control volume. In order to enable commerical development, complex hydraulic-fracture networks must be created in the shale to allow gas to escape from the micro/nano-pores and natural fractures where it is trapped in the rock (C. Clark et al.,2013; Ge et al., 2013). The development of shale gas requires accurate evaluation methodologies to evaluate shale reservoir properties and predict production. (Jarvie et al., 2007). Rock mechanical properties are an important part of the reservoir evaluation. It is significant for efficient drilling, completion and hydraulic fracturing to understand mechanical behavior of shale gas play (John, 2011; Wei, 2013).Rock mechanical properties mainly include heterogeneity, anisotropy, brittleness and acoustic emission activity (Lockner et al., 1992; Jerome et al., 2009; He et al., 2010; Liang et al., 2012). Shale mechanical properties are evaluated from laboratory tests following a complex workflow that covers tasks from sampling to testing (Md. Aminul Islam et al., 2013). It is common to include various experimental methods such as stress-strain curves, ultrasonic velocity and acoustic emission when evaluating the mechanical properties (Rao et al., 2006). Because of the presence of organic-rich matter, mineral composition orientation and natural fractures, shale tends to have strong anisotropy and heterogeneity (Deng et al., 2004; Wang et al., 2013; Hathon et al., 2013)."

Jan 1, 2015

By C. Bernier

This paper deals with three major problems associated with mining operations during the winter. These are the maintenance of the cooling systems of diesel engines, the high incidence of hydraulic dump failures on packaging machines, and the build-up of frozen fines on wet-ore conveyor belts.

Jan 1, 1966

By Jean Vavrek

What is CIM?s role on a planet-wide scale? That question has been coming back to the forefront of many discussions regularly in the months since we came on board as Executive Director and Vice-President International. CIM, by its name and by the nature of its history and make up, has mainly been a Canadian entity. It has been created by an act of Canadian Parliament and it is set up to work within the Canadian federal and provincial framework.

Feb 1, 2004

For the last few years, a new and innovative technique has been successfully used to determine refractory and castable thickness in various metallurgical vessels. The acousto ultrasonic-echo (AU-E) technique uses stress waves to detect metal penetration and delaminations within refractory linings. In addition, it is capable of measuring the thickness of refractory layers and build-up material. The inspection and measurements can be carried out while the furnace is in full operation. The present paper discusses the principles of the AU-E technique, and its advantages and limitations. A number of case studies are presented to demonstrate various capabilities of this new Non-Destructive Testing (NDT) technique.

Jan 1, 2005

By I. A. Tinto

"Labrador City is located in the southwestern portion of Newfoundland-Labrador, approximately 965 kilometers north-east of Montreal. The mine and beneficiation complex of the Iron Ore Company of Canada, known as the Carol Project, is situated 535 metres above sea level in a climatic region characterized by cold winters and short, cool summers.HistoryThe Iron Ore Company of Canada commenced work in the area in 19 4 9' however, it was not until 1958 that the decision was made to proceed with mining operations. The ore body consists of Specular Hematite (Fe203) and Magnetite (Fe304) with small quantities of Limonite and Geothite. The average grade of the ore bodies is 39% iron.The mining facilities, crushing plant, and concentrator were in operation by the early part of 1962. In the summer of 1961, a decision was made to build a pelletizing plant adjacent to the concentrator. This plant was designed, erected and placed in operation during 1962 and the first half of 1963. Since the completion of the pelletizing plant, additional expansions to both the pellet plant and concentrator have taken place in 1967 and 1973. Today, the Carol Project has the capacity to produce 20 million tonnes of concentrate from which 10.5 million tonnes of pellets can be produced.The period 1980-85 spans a period of energy crisis, world-wide recession, and a consequent re-structuring of the North American steel industry as it struggles to survive in an arena of excess world steel making capacity, government subsidized industries, and the increasing competition from overseas and from developing countries.The media headlines over the past few years echo the woes of the industry and the strategy plans for survival of the fittest. Today's buzz words are foreign competition, steel import quotas, joint ventures, employee participation, work rules, quality, productivity, and state of the art technology."

Jan 1, 1986

By Ray Mason, Damien Label, Howard Bernier, Kevin McDermott, Kevin Coombs

"GeneralWabush Mines is an unincorporated joint venture of seven steel companies and Pickands Mather & Co. The mining and concentrating facilities are located in southwestern Labrador and the pelletizing and shiploading facilities are at Pointe Noire, 200 miles south, near the town of Sept-lies.The operation is based on a 5 ½ sq. mi. specular hematite deposit with a reserve of 375 million tons of concentrate. Annual production capacity is rated at 6 million tons of pellets per year. The final upgrading process utilizes high-tension separation of silica following wet autogenous grinding, spiral gravity separation and fluo-solids drying. The concentrate is railed in closed cars to Pointe Noire. The concentrate is reground dry and pelletized on Dravo Lurgi travelling grate machines to produce an oxide pellet with 65.5% Fe, 3.0% Si02, 1.95% Mn and 93.5% Tumble Index.HistoryPlant operations commenced in 1965 with a concentrator capacity of 5.3 million tons per year and a pelletizing capacity of 4.8 million tons per year. The original facilities for classifying the crude ore into fine and coarse fractions for storage purposes before reblending as autogenous mill feed were found to be unnecessary and were by-passed after plant startup. Capacity of the operation was increased to 6.0 million tons of pellets per year in 1968. This increased capacity required the installation of an additional160 cleaner spirals in the ore dressing plant, a new 5000 hp ball mill, three balling circuits and increased cooling air capacity in the pellet plant.In 1970, the regrind circuit in the pellet plant was converted to dry grinding and a significant reduction in grinding media consumption and maintenance costs was realized. A ninth grinding mill of 5000 hp capacity was installed to compensate for the reduced capacity in going from wet to dry grinding."

Jan 1, 2000

By J. A. Vallejos

Re-entry protocols are a tactical approach for controlling risk after blasts or large events in seismically active mines. Based on the results of a survey on 18 seismically active mines, mostly in Ontario, current re-entry practices are summarized. Over half of the mines in Ontario use event decay rate analysis as their primary re-entry decision making parameter. We study in detail the applicability of the Omori?s law as an equation for describing the event decay rate for more than 250 mining-induced aftershock sequences in seven different environments. Practical guidelines for the use of the Omori equation as a re-entry criterion are proposed.

May 1, 2009