Search Documents

By A. Hashempour, D. Javani

"Selection of an optimal bit is a critical issue in drilling engineering. Specific energy (SE) and Cost per Foot (CPF) are the most common methods for evaluation of bit efficiency and optimal bit selection. The major shortfall of both methods is that they do not directly account for geological and geomechanical parameters of formations being drilling. In this paper, results of using the two foregoing methods are compared using Formation Drillability (FD) method, which directly accounts for geological and geomechanical parameters of a formation. This method combines various geological and geomechanical parameters and yields a dimensionless parameter indicating the formation drilling hardness (drillability). Results of this study show that the amount of energy, cost and time spent for drilling a unit volume / length of an identical formation may vary in different wells. This is due to the fact that geological and geomechanical characteristics of a formation may vary among wells and even within short intervals of a single well. Therefore, an optimal bit may not be appropriately selected, if drilling and economical parameters are the only factors considered and the formation geological and geomechanical specifications are ignored.INTRODUCTIONMany authors such as Bilgesu, Al-Rashidi, Aminian, and Ameri (2000) and Clegg (2006) conducted research in the evaluation of bit performance and optimum bit selection. Almost all of them tried to establish a good relationship based on geomechanical parameters. Primary examples are the research done by Ubaldi (1999), Macini, Magagni, Da Dalt, and Valente (2007)."

Jan 1, 2015

By R. Browner, J. Collard, D. Ibana

The extraction of cobalt from synthetic pressure acid leach solutions of nickel laterite ores by the direct solvent extraction route using ESPLIM is reported. It first explored the use of gaseous ammonia as pH modifier and then the variables that affect the dispersion of the aqueous phase in the organic phase such as ionic strength, viscosity of the phases, initial droplet size, etc. were explored so that phase hold-up and thus extraction can be effectively controlled. The results show that the technique allows better control of phase dispersion circumventing one of the main weaknesses of conventional solvent extraction.

Jan 1, 2005

By S. D. Botts, F. Cantuarias

"The Antamina project, owned by BHP Billiton Plc, Mitsubishi Corporation, Noranda Inc., and Teck Cominco Ltd., is a $2.3 billion copper/ zinc project, located in the Ancash Department of Peru. The project consists of an open pit mine, a 70 000 ton per day concentrator, a 302 km long concentrate pipeline, port facilities, a new access road, power line, and town site. The project is designed to produce up to 1.5 Mtpy of copper and zinc concentrates over a 23 year project life, and will be the third largest producer of zinc and the seventh largest producer of copper in the world.This mega project is the largest mining investment in the country and, during its construction stage, was the most important construction project worldwide. On May 28, 2001, Antamina commenced testing operations and four months later, it reached commercial production. Antamina was officially inaugurated on November 14, 2001 by Peruvian president Alejandro Toledo.The construction stage of the project generated 8000 direct jobs, with a peak of 10 000 employees, and 30 000 indirect jobs. The permanent workforce consists of approximately 1650 employees, the vast majority of which are Peruvian Nationals, around 30% of whom came from the region where the deposit is located. Approximately 5600 indirect jobs were generated from the project. Independent sources state that Antamina increased the Peruvian mining exports by 30% (mining exports constitute 50% of Peru’s total exports) and Peruvian GDP by 1% in its first year of full operation in 2002.Since winning the privatization bid for the project in 1996, the company has implemented an approach to community development and environmental protection based on sustainable development principals. Throughout the development of the project, a number of initiatives have been undertaken to ensure full involvement of the local populations in community development activities and the company’s environmental program.Due to its size, difficult logistics, cultural considerations and financial aspects, the project has faced a number of unique challenges in the area of environmental protection and management of community interaction. Antamina has been innovative in its approach to these issues and, as a result, has set new standards in Peru for environmental and community management and sustainable development."

Jan 1, 2003

By W. Hrynewich

"The Central Canada Potash facility, a division of Noranda Metal Industries Limited, is located 3 kilometres south of the junction of Highways 16 and 2, about 75 kilometres south-east of Saskatoon, Saskatchewan. The site occupies 26~ hectares of land and includes well-equipped machine and electrical _shops, a 325,000-tonne muriate storage and reclaim warehouse, a stores warehouse, processing plant (mill), two mine shafts (one for production, the other for servicing and personnel transport), as well as a two track product loading complex. Access to the site is by road and railway (CN and CP Rail). Suppliers of operating and maintenance use both means of transportation, whereas muriate shipments are entirely by railway.Currently five continuous mining machines - one a Goodman 526 borer and four Marietta 911-A units produce some 10,500 tonnes of ore per operating day. A smaller Voest-Alpine Af.1-100 boom type miner is used for floor cutting which was previously done by a production unit. In order to maintain safe, competent ground conditions only 35 percent of the total ore is extracted. At this rate mine reserves are deemed adequate for about 100 years. The plant has operated since August 1969 and has a current practical annual capacity of 1,270,000 tonnes of muriate. As of June 30, 1981, some 11.9 million tonnes of muriate had been produced from 31.4 million tonnes of ore. Of the total muriate, 6.1 million tonnes was granular, 4.8 million was coarse, and 1.0 million was standard. No standard product has been made since August 1978."

Jan 1, 1982

By F. M. Waldie

THE 2,538-foot belt conveyor recently installed underground at the Sullivan mine hoists ore from the 3,350-foot level to the 3,900-foot or main haulage level, a vertical distance of 680 feet. The design and planning of development work, under the direction of Mr. R. H. Stewart, Consulting Engineer, was begun in the spring of 1941. Development work was started in July of that year from the 3,350-foot level, and headings were started on the 3,650-foot and 3,900-foot levels later in the same year. It was the intention at that time to keep three headings going on development work necessary for the installation of the system: two on the conveyor incline, and one on the 3,900-foot level. This programme was modified in 1942 when there was some doubt whether the material for construction could be obtained. This problem of supply was eventually solved and the development work was pushed to completion in December, 1943. Construction was started in December, 1943, "'under the supervision of Mr. G. H. McKay, Superintendent of Construction and? Maintenance, and was completed in November, 1944.

Jan 1, 1945

By C. T. Bischoff

Introduction Air conditioning is a term which has come into common use only during our generation. By definition, it means the positive and accurate control of temperature, humidity, movement, purity, and component constituents of the atmosphere within an enclosure. Claiming such results for Noranda's ventilation system, or for that of any other large mine, at present would be an idle boast. However, we are working toward that end with considerable success. Modern underground ventilation at Noranda dates back about six years. The later development of air conditioning is in its fourth season, but still in the experimental stage. Various ingenious methods have been devised to cool mines which, because of climatic or geological conditions or depth, are excessively warm. A few installations have been made to warm intake air during the winter months where this is necessary. However, the method currently in use at Noranda is unique in that it accomplishes both ends by one process. This method utilizes the freezing and melting of ice to equalize year-round temperatures. Mining Methods While a discussion of mining methods at Noranda is not proposed in this paper, a brief summary may be in order. The Horne mine of Noranda Mines, Limited, has been developed by six shafts, four of which are now active. The most recent, an internal shaft, extends to 6,000 feet below surface, but all of the ore mined to date has come from above the 3,000-foot level. Figure 1 shows a model of principal ore bodies. The area mined is relatively small in plan, considering its vertical extent and the tonnage per vertical foot. Most of the ore lies within an ellipse about 600 by 1,000 feet. While this has certain advantages, the mining of such massive orebodies has presented many problems.

Jan 1, 1947

By P. Bousquet

Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian mining industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage phenomenon. AMD occurs when sulphide minerals (e.g., pyrite) contained in rock are exposed to air and water and subsequently oxidize to produce low pH water. This acid effluent has the potential to mobilize any heavy metals contained in the rock. Coating the sulphide minerals with silicates is a new promising technology to reduce AMD. Pyrite is treated with a solution containing H2O2, sodium silicate and a buffering agent. H2O2 oxidizes a small part of pyrite producing ferric iron (Fe3+) ions. These ions subsequently react with the silicate ions to produce ferric hydroxide-silica that precipitates on the pyrite surface producing a passive coating. This silicate coating can protect the grains of pyrite from oxidation. This paper presents a series of experiments that confirm that silicate coating can considerably reduce AMD.

Jan 1, 2002

By Nick Vayenas, Ming Cai, Hongbin Zhang Lorrie Fava, Enrique Acuña

"A hybrid methodology is proposed to improve the accuracy of Diesel Particulate Matter (DPM) concentrations simulated in a ventilation network model by using Computational Fluid Dynamics (CFD). DPM, as a primary concern for underground hard-rock mines, has been studied in two dominant numerical models, ventilation network solvers and computational fluid dynamics. Ventilation network solvers are efficient, but they are not able to provide three-dimensional DPM concentration contours and only accept area-average DPM data as input. CFD simulations are time-consuming, but generating DPM concentration results with high accuracy. Besides, both monitoring points and planes can be created in a CFD model, which can take both point data and area-average DPM data as input. The hybrid methodology is intended to combine the advantages of the two by using the CFD results to update the network model results at key locations. A field study was conducted in a dead-end heading in an underground gold mine in the United States. Real-time DPM monitors were used to collect data. A CFD model and a network model were built for the experiment area. The CFD model was calibrated to the experimental data. In the study presented here, results from a calibrated CFD model are converted to equivalent diesel emission rates in the ventilation network model at a shared outlet. The hybrid methodology is used to provide better input for the network model. INTRODUCTION Mine ventilation system is one of the most important parts for an underground mine. It not only provides fresh air to the personnel but also helps clear the contaminants generated from the diesel-powered equipment. For most underground metal and non-metal mines, diesel particulate matter is the main contaminant. It is also the focus of this paper."

Jan 1, 2019

By B. T. Lu, J. L. Luo, T. Yu, C. W. Chen

In this paper, the synergism in erosion-corrosion process occurring in oil sand wastewater transportation caused by the interaction of mechanical and electrochemical factors was experimentally investigated. The erosion-corrosion tests were conducted with A1045 steel in synthetic slurries comprising tap water and silica sand. The material loss due to corrosion-enhanced erosion was assessed with the chemo-mechanical model developed by the authors recently. The results indicate that the material loss produced by corrosion-enhanced erosion at the open circuit potential can be formulated as a linear function of logarithm of corrosion current density. The wastage caused by the erosion-enhanced corrosion was analyzed based on the concept of non-equilibrium thermodynamics. The material loss induced by the erosion-enhanced corrosion is approximately a linear function of overall erosion rate measured in synthetic slurries, indicating that erosion-enhanced corrosion could be reduced by adopting surface strengthening techniques to improve the resistance to the plastic deformation in surface layer.

Jan 1, 2004

By D. Milne, G. Snell

"A new method to predict stope hangingwall failure in underground excavations is proposed. This method compares movement rate for stope hangingwalls, determined from changes in strain or deformation, with changing opening geometry. This geometry is represented by the effective radius factor (ERF), a measure of relative distance to supporting abutments from an opening surface point. This strain-ERF (SERF) approach is applied to an instrumentation program for Brunswick mine near Bathurst, New Brunswick. The SERF method for this case study predicted failure at an ERF of 13.9 m and hangingwall failure actually occurred at an approximate ERF of 12.4 m.RÉSUMÉ Cet article propose une nouvelle méthode permettant de prévoir la rupture de l’éponte supérieure des chambres d’abattage dans les excavations souterraines. Cette méthode compare la vitesse de mouvement des épontes supérieures des chambres d’abattage, déterminée à partir des changements aux niveaux des contraintes ou de la déformation, à la géométrie variable de l’ouverture au jour. Cette géométrie est représentée par le facteur du rayon effectif (ERF, de l’anglais Effective Radius Factor), une mesure de la distance relative jusqu’aux appuis latéraux de soutènement à partir d’un point de la surface d’ouverture au jour. Cette approche contraintes-ERF (SERF, de l’anglais strain-ERF) est appliquée à un programme d’instrumentation pour la mine Brunswick située près de Bathurst, dans le Nouveau-Brunswick. Pour cette étude de cas, la méthode SERF prévoyait une rupture à un ERF de 13,9 mètres (m); la rupture de l’éponte supérieure s’est effectivement produite à un ERF d’environ 12,4 m.INTRODUCTIONUnderground stope design can be improved with the installation of field instrumentation. The most commonly used instrumentation for monitoring rock mass behaviour around open stopes is extensometers. The y-axis of Figure 1 represents how the changing rate of movement, measured using either displacement- or stress-type instruments, can be observed over time. The magnitude of movement measured by extensometers can give an approximation of the load on installed support (Milne, Pakalnis, & Lunder, 1996) and a changing rate of movement can indicate approaching instability."

Jan 1, 2018

By S. C. Robinson

"IntroductionALTHOUGH most uranium deposits of the Canadian Shield lie along its western and southern margins, those of the Lake Athabasca region extend easterly along the north shore of the lake and beyond to Charlebois lake. The western end of this belt of deposits, in the vicinity of Goldfields, is 80 miles from the Palaeozoic contact, and its eastern end, at Charlebois lake, is 240 miles from the nearest Palaeozoic rocks.Deposits in this belt may be grouped in four districts, which are, from west to east:(1) The Goldfields district, an area approximately 20 miles square, centred on Beaverlodge lake and extending eastward from St. Joseph's point to Moose channel.(2) A small area in the vicinity of Sucker bay, which is about l0 miles east of Fond du Lac.(3) An area including Middle lake to the northwest shore of Black lake at the Nisto mine.(4) A fairly large area extending northward from the eastern end of Black lake, through Charlebois lake to Spreckley lake.HistoryThe region has stimulated interest in mining circles since the reconnaissance survey of J. B. Tyrrell of the Geological Survey of Canada in l893, who reported concentrations of iron along the north shore of lake Athabasca. The deposits were staked and re-staked up to the early 'twenties' but are too lean to form ore."

Jan 1, 1952

By A. Glover

As the demand for natural gas as a prime global energy source continues to grow, the search for new sources of the fuel spreads into geographical areas that are more remote from the marketplace. Along with this comes the need for longer and ever more efficient pipelines. This requirement for higher value in natural gas transportation is satisfied to a large extent through the application of high strength technology and innovative design approaches that support increased design and operating pressures. This paper reviews the latest accomplishments and successes in these technologies for use in gas transmission. It also explores some of the technologies which are targeted for the future to allow the industry to achieve even higher benchmarks in reliability and cost-effectiveness. The central element in the theme of high strength technology for gas pipelines is that of high strength steel. From tensile strengths of Grade 359 a few decades ago, more and more operators are now specifying Grade 550 linepipe for their large diameter projects. As well, Grade 690 steel is operating successfully in limited transmission applications and Grade 825 has recently been installed. With the introduction of the latest high strength pipe comes the need for high strength fittings. The industry's first Grade 550 fittings were recently specified and installed on a project with Grade 825 line pipe. High strength materials can only be implemented successfully if compatible design and construction processes are in place. The latest developments in strain- and reliability based design will be described as well as the corresponding advancements in welding and inspection technology.

Jan 1, 2005

By Beatrice Pierre, Juan Carrasco

Altonorte began as a concentrate roasting operation in 1988 under the name of Refimet. In 1993, a copper smelter was built with a design capacity of 203,000 tonnes per annum of concentrate. Since 2001, many technological advances have been made in Altonorte, where the biggest Noranda Reactor in the world is installed being the first Noranda Reactor reaching above one million tonnes of copper concentrates processed per annum. In 2013, Altonorte was acquired by Glencore. Recently due to various new environmental regulations in Chile, Altonorte has evolved to new standards of operation in order to reach the vision of becoming a World Class Smelter. This paper describes the path followed to improve safety, environmental performance, process capacity, reliability, and productivity. The foundation for the growth and success in Altonorte is our People. Employee engagement and branding of our cultural journey is what allows Altonorte to face the future with the certainty of becoming a World Class Smelter. INTRODUCTION Altonorte is located in Antofagasta, the mining capital in the north of Chile and is the last smelter built in Chile practically completed with second hand equipment. The biggest technological change in Altonorte occurred during the phase 3 expansion in 2003, where the old Reverberatory furnace was shut down and replaced by the biggest Noranda Reactor installed in the world. The vessel measures 5.3 m × 26m. ºAdditionally, this project contemplated a new rotary dryer, three (3) new Peirce Smith converters, new anode furnaces and a new Acid plant. The nominal capacity was to treat 816.000 tons of new concentrate per year. In 2008, a new expansion phase was implemented where a new double absorption acid plant replaced the oldest acid plant. Bottlenecks such as blowing capacity and oxygen availability were solved installing a new air blower and a new contract was negotiated with our oxygen supplier to increase oxygen availability up to 683 tpd. This improvement defined the current nominal capacity of 1.100.000 ton of new concentrate per year. Current process description All concentrates are received by trucks directly from domestic mines or from the Antofagasta international port in cases of imported concentrates; the concentrate warehouse has a capacity of 25 kt where the blend is prepared to feed the smelter.

Jan 1, 2019

By N. Erarslan, M. Ghamgosar

With the increased use of mechanized rock excavation, there have been developed internationally a number of methods to assess the abrasivity of rock materials. These methods range from determination of abrasive and hard mineral content using petrographic thin section analysis to weight loss or rate of wear flat development on specified test pieces. The Cerchar abrasivity index (CAI) test has been widely accepted for the assessment of rock abrasiveness and is determined as the abrasion of a steel pin after scratching over the freshly-broken or saw-cut surface of a rock. Two types of testing devices are in use today: (i) the original ‘Cerchar apparatus’, and (ii) the ‘West apparatus’, which was adopted herein. The CAI is calculated from the measured diameter of the resulting wear flat on the steel pin after 10mm scratching. This test has been considered to provide a reliable indication of rock abrasiveness for isotropic rocks. However, a great amount of rocks in natureis anisotropic. Phyllite is an anisotropic and foliated metamorphic rock and various types of phyllite specimens were tested in this research. Although phyllite is a type of rock primarily composed of quartz and the expected CAI value can be high, mechanical cutting of this rock should not be very problematic compared with igneous rocks have same CAI value. As phyllite is a foliated metamorphic rock, most of the specimens split into sheets through the quartz seam by the tip during scratching normal to the axis of quartz seams. Hence, viability assessment of Cerchar abrasivity test and F-Schimazek index values for the anisotropic rocks is investigated in this research.

Jan 1, 2015

By W. T. Robson

ONE of the problems encountered in any mine is the effect of increasing pressure manifested by increasing depth. Although the depth at which excessive pressure assumes serious proportion, and the manner in which it appears in underground workings, are influenced by a variety of factors, nevertheless the difficulty is present in all mines and its gravity increases with increasing depth. In the Kirkland Lake camp, as far back as seven years ago, mining had proceeded to depths sufficient to result in the formation of pressure great enough to cause violent disruption of masses of rock. It is proposed in this paper to deal with the effect of pressure caused by mining as observed at Lake Shore Mines, and to describe some of the methods which have been adopted to counteract it. There are many contributing factors in a study of the problem, and results vary widely in individual mines and in different localities. One feature common to all, however, is that there is ground subsidence, evidenced either by a gradual settling accompanied by crushing and shearing of the ore and wall-rocks, or the disruption of the ground surrounding the periphery of an excavation may take place suddenly, attended by more or less violent shattering of the rocks. Such violent failure of a mass of rock has been designated by the term rock-burst. The history of rock-bursts extends over a great number of years. They have occurred in some form or other in practically ali places where mining operations, at all but very shallow depths, have been carried out. Since the theoretical aspects of the subject have been dealt 'with at great length by capable and experienced writers (1), the present paper will give only a brief résumé of the theories propounded by those engaged in deep mining operations in various parts of the world.

Jan 1, 1940

By William Winsor, Harold L. Snyder

"AbstractShould oil and gas be proven in commercial quantities on the Labrador Shelf, current technology is not adequate for production operations in this severe environment, which includes yearly invasion of pack ice and icebergs. The fishery of this section of the North Atlantic is a vital resource to which a major oil spill or blow-out would impose an intolerable burden, This means that production systems must be designed and built to be fail-safe.The experiences of mining in Bell Island and Cape Breton have shown that it is possible to operate beneath the ocean floor, and this technology may hold the key for safe, reliable and economic production, This paper attempts to define particular problems and outline possible solutions.IntroductionOUR DISCUSSION is subject to the assumption that large hydrocarbon reservoirs will be discovered in the sedimentary basin of the Labrador continental margin. The petroleum industry has not attempted to operate in a harsher area. The Labrador coastline is exposed to North Atlantic storms and icebergs year’round, Arctic pack ice occurs up to six months of each year. However, there is no doubt that, if sufficient hydrocarbon potential is outlined, development will proceed."

Jan 1, 1977

By J. E. Hawley

This paper constitutes a report from the Committee on Geological Research to the Geology Division of the Institute. Two years have elapsed since a formal report was made containing several resolutions aimed at assisting geological research, a review of research equipment available, a summary of research projects suggested for consideration, and a list of research then in progress (see July, 1947, Bulletin, pp. 351-370). At this time we may note what action has been taken on the various resotions and suggestions of the Committee, indicate the more important accomplishments of independent investigators, and present a summary of the rather imposing volume and variety of research currently being carried on throughout the country. I.-Committee Resolutions and Suggestions 1.-A National Advisory Committee on Research in the Geological Sciences The original resolution adopted on the setting up of this Committee was approved with despatch by Council and was forwarded to the Minister of Mines and Resources. Due to a reorganization in the Department and possibly other reasons, no action on this important matter has yet been taken, but we are assured that some time this year such a Committee will be established by the Department of Mines and Resources. Unquestionably, it will give a fresh impetus to research in the geological sciences. When the noteworthy progress made by the research committees on Geophysics and on Soil and Snow Mechanics, established by the National Research Council, is considered, it is indeed regrettable that the Department of Mines and Resources has not acted more decisively in this matter.

Jan 1, 1949

By Antonio Segatori, Bjørn Holmedal, Kai Zhang, Trond Aukrust, Knut Marthinsen

"The visual appearance and mechanical properties of aluminium alloy extrusions are strongly dependent on the microstructure and texture of the extruded profiles, where the desired microstructure and texture may depend on the specific applications. In the present work, the evolution of deformation, as well as recrystallization textures during extrusion of AA6xxx aluminium alloys, have been experimentally and numerically investigated. Extrusion trials were performed in a laboratory extrusion set-up, which enabled immediate water-quenching of the profiles at the exit of the die, and thus the possibility to capture the deformation texture prior to post-extrusion recrystallization. The textures and their through-thickness variations were experimentally measured by the electron back-scatter diffraction technique (EBSD, and the deformation textures numerically modelled by coupling FEM flow simulations and crystal plasticity (CP) simulations. Different CP models as well as different choices of model parameters were employed and evaluated for texture predictions. With an appropriate choice of crystal plasticity model and model parameters, the deformation texture can mainly be predicted, although the accurate intensities are hard to reproduce. The corresponding recrystallization textures, either generated through spontaneous recrystallization of the extruded profiles or through post-extrusion annealing, are far more challenging to reproduce with available recrystallization models.INTRODUCTION Extrusion is a widely applied thermal-mechanical process to produce aluminium profiles. The properties of the profiles, for example mechanical, fatigue, fracture, corrosion as well surface appearance, are strongly dependent on the underlying microstructure and texture, and the requirements with respect to these aspects may vary with applications (Ralston et al., 2010; Dumoulin et al., 2012; Donati et al., 2013). Moreover, it is often a challenge to produce extrusions with a consistent and homogenous grain structure and texture along as well as through the cross section of the profiles. It is thus vital to understand and be able to predict (model) how different microstructures and textures are formed and how they evolve during and after extrusion, as basis for controlling the final appearance and properties of extruded profiles."

Jan 1, 2018

By H. R. Stockford

"A pyroxenite-carbonatite complex containing extensive pyrochlore mineralization was discovered during January, 1966, within an exploratory license area held by Consolidated Morrison Explorations Limited. Located 32 miles south of Moosonee, Ontario, the deposit was found under 100 feet of glacial till and Paleozoic sedimentary cover using airborne and ground magnetometer surveys. Exploratory and detailed drilling, totalling 47,625 feet in 85 holes, was completed in outlining the deposit to a maximum depth of 900 feet. Pyrochlore reserves are estimated at 62,000,000 tons averaging 0.52 per cent Cb,05 to a depth of 825 feet. Included in this tonnage is a high-grade section containing 10,000 tons per vertical foot grading 0.82 per cent Cb20 5• The deposit is still open at depth and the intrusive complex has by no means been fully explored.The columbium (niobium) mineralization occurs in a lineated calcite-dolomite host rock which has been intruded along a fault zone within a northeast-trending granulite belt. Potassium-argon dating indicates an age of 1655 million years.Preliminary studies suggest that the complex was intruded in a series of pulses in the form of a partially crystallized mush. The James Bay intrusive is unusual in that it is linear in form and contains only two main rock types - p•yroxenite and carbonatite. Nepheline-bearing syenites and associated rocks are notably absent. Moreover, the pyrochlore is essentially non-radioactive and free from many of the impurities generally associated with other pyrochlores. A test shaft to investigate soil conditions and to provide a 250-ton bulk sample was completed during 1968. Subsequent pilot-plant operations indicate that good quality pyrochlore concelttrates can be produced from this deposit."

Jan 1, 1972

By H. P. Dibbs

An account is given of the application of neutron activation analysis to the rapid, non-destructive determination of copper in minerals, using a 14-MeV neutron source. Elements that interfere in the determination of copper by this method are given, together with the errors in the estimation of copper that result from the presence of varying amounts of these elements. The possible use of a compact "sealed-tube" 14-MeV neutron generator for the field assay of copper in minerals is discussed.

Jan 1, 1970