Search Documents

By Lev Filippov, Saeed Farrokhpay

"Flotation process has had less success to recover nickel from laterite ores. Nickel in laterite ores is often finely disseminated in various minerals in very fine size. Therefore, fine grinding should be used to liberate nickel containing particles. Particles resulted from fine grinding are often very fine, and recovery of such particles is generally low using conventional flotation methods. One option to overcome this problem is enhancing the particle-bubble interaction by increasing the particle size and forming flocs. Selective flocculation of fine particle can be therefore the key to enhance the flotation performance of low grade laterite ores.INTRODUCTIONThe majority of the world’s nickel resources occur as laterite ores which are complex, low grade and expensive to treat using conventional smelting and high temperature and/or high pressure autoclave methods (Xu et al., 2013). While about 70% of the nickel resources are contained in laterites, only 40% of the world’s nickel production comes from these ores. Researchers have tried to improve the nickel laterite flotation recovery by using a number of feed preparation techniques. For example, in a study on a laterite ore sample from Australia, flotation tests on a narrow sized fraction of 38-75 µm resulted in only a small increase in the nickel content, from 1.0% to 1.4% (Quast et al., 2015a). In fact, no physical separation technique (including flotation) has been able to dramatically upgrade nickel in laterite ores (Quast et al., 2015b). Thus the challenge of processing low grade nickel laterite ores still exists. This paper aims to explore the possibility of applying selective aggregation in pre-concentrating of valuable minerals in nickel laterite ores."

Jan 1, 2016

By D. G. Sediako

Chemical composition and the casting/rolling production routes determine the cost and properties of the wrought material. For example, the coarse-grained structure frequently associated with DC casting requires complex rolling schedules to refine the grain size. Hot forming (rolling/forging/extrusion) results in a strong crystallographic texture, which is responsible for the tension-compression strength asymmetry frequently exhibited by magnesium alloys. Understanding the influence of alloy composition on texture evolution during forming provides useful practical information to optimize industrial hot-forming technologies for magnesium alloys. In this study, a series of Mg-based alloys containing varying combinations of Al, Rare Earths, Zn, Ca, and Sr were subjected to identical casting and extrusion processes in order to isolate the effects of alloy composition on texture evolution. Textures were measured by neutron diffraction at the NRC Canadian Neutron Beam Centre. The ability of neutrons to penetrate deeply into materials allowed information to be retrieved from all regions of the bulk specimens without destructive and time-consuming sectioning operations, thereby providing true bulk texture data. {1010} , (0002), {1011}, and {1012} pole figures were generated for all of the as-processed alloys, from which Orientation Density Functions were obtained. The were then used to reconstruct the pole figures and to extract semi-quantitative texture data showing how the (0002) and {1010} planes align themselves with respect to the extrusion axis. It was found that varying the concentration of aluminum (3-4 wt%) and Rare Earths (2-3 wt%) in AE alloys had a weak effect on texture development. All of the alloys showed similar magnesium extrusion textures, in which the (0002) poles align themselves preferentially with the extrusion axis. The substitution of Sr for Rare Earths also did not have a significant impact on texture development. On the other hand, while the presence of small amounts of Zn and Rare Earths did not have a strong effect on texture development, alloys with higher concentrations of these alloying additions (in combination) showed an enhanced tendency for the {1010} poles to align themselves with the extrusion axis. The addition of Ca also enhanced the alignment of the {1010} poles with the extrusion axis. These textures can complicate further processing and introduce a significant anisotropy that could influence creep properties.

Jan 1, 2007

By N. Fukatsu

The recent development of galvanic cell-type hydrogen sensor for molten copper was outlined. The principle of the sensing mechanism, the fundamental structure of the sensor, and its performance as a process control device are discussed based on experimental work undertaken by the authors. Besides sensors based on usual perovskite-type proton conducting oxide, those using magnesium-doped alpha alumina, which was recently known as a proton conductor, were investigated and the results at the laboratory scale are reported. Considering the excellent sensitivity at high temperature and the stability to the disturbance from the attendant oxygen activity, magnesium-doped alpha alumina was regarded to be a superior material for the sensors used for such purposes.

Jan 1, 2007

By C. Mills, A. O. Burt

"The paper examines the role of gravity concentration in both an historical context and within the modern mineral processing industry. It discusses the principles of the process on both a theoretical and practical level. The importance of more mineralogy and its effect on the choice of the wide range of equipment available is discussed. The paper concludes with a discussion on the relative merits of gravity concentration with other forms of processing.IntroductionIt is an unfortunate, albeit popular, misconception among otherwise enlightened engineers in the mineral processing industry that gravity concentration was a process developed in the dark ages, perfected in the middle ages, and abandoned in the modern ages.Gravity concentration was developed in the dark ages - long indeed before that. Agricolau: cited examples of gravity concentration, crude examples admittedly, being practiced over 3000 years ago. However, gravity concentration is not dead. Far from it. As recently as 1978 it was reported that the total mineral tonnage treated by this process in the United States was greater than that processed by flotation. Coal represents the bulk of the or e treated by gravity separation in the U.S.A., with iron ore representing a major portion of the balance."

Jan 1, 1985

By J. Desroches, J. Burghardt, B. Lecampion, A. P. Bunger

"We present detailed comparisons between theoretical predictions and experiments for the initiation of radial hydraulic fractures transverse to a wellbore. Most of these experiments provide a measure of the time evolution of pressure, length, opening and flux entering the fracture during the test. We compare all these measurements simultaneously to our theoretical predictions, thoroughly testing hydraulic fracture initiation theory, which is shown to be predictive. These comparisons notably emphasize the difference between the initiation pressure (the wellbore pressure for which the fracture initiates) and the breakdown pressure (a misnomer which simply corresponds to the maximum pressure recorded during the test). INTRODUCTION In this paper, we will compare hydraulic fracturing laboratory experiments performed in different tight materials (PMMA, cement, shale) with the predictions from a numerical solution of the governing equations of hydraulic fracture mechanics (e.g. Geerstma & de Klerk, 1969; Detournay & Peirce, 2014). We focus on transverse radial hydraulic fractures initiating from a radial notch at the wellbore wall (see Figure 1). In particular, we will clarify the difference between the initiation pressure (the wellbore pressure at which the fracture initiates) and the breakdown pressure (a misnomer which simply corresponds to the maximum pressure recorded during a test, usually carried out at constant pump rate). This difference stems from the strong viscous effects at play during wellbore pressurization, fracture initiation and early propagation (i.e. fluid entrance in the newly created fracture). It has been observed on a number of experiments (e.g. Weijers, 1995; Zhao et al., 1996) and has a strong practical application, first because the maximum pressure is the most obvious value to report and second because that maximum value is necessary to specify injection systems."

Jan 1, 2015

By Lastram Rolando, Larry J. Hulbert, Louis J. Cabri, J. H. Gille Laflamme, John L. Campbell, Soey H. Sib, Chris G. Ryan

"The mineralogy of samples from the Wellgreen Cu-Ni-Pt-Pd deposit, Yukon Territory, is complex and the metals of interest are contained within fine-grained minerals which vary in size and mineral associations from sample to sample.The major Ni carriers are pentlandite and violarite; the major Cu carrier is chalcopyrite. About 700/0 of the major Ni carriers and 78% of the major Cu qurier will be liberated at a grind of 80% -U,.7 ,an (-500 mesh) for typical low-grade gabbro (West zone, sample No.1). For typical ""clinopyroxenite"" (West zone, sample No.2) and typical ""clinopyroxene-rich peridotite"" (East zone, sample No.3) the liberation would be 71% and 65% for Ni, 74% and 60% for Cu, respectively. Fine grinding, however, cannot liberate the Ni contained in silicates and pyrrhotite, estimated to total 24.5% for typical low-grade gabbro (West zone, sample No. I), 15% for typical ""clinopyroxenite"" (West zone, sample No.2), and 12% for typical ""clinopyroxene-rich peridotite"" (East zone, sample No.3).The principal Pt carrier (sperrylite) varies considerably in grain-size between samples and fine grinding, required to liberate the major Ni and Cu carriers, may be counterproductive in samples where sperrylite is relatively coarse-grained, as some would then be unrecovered (e.g. sample No. 1). In addition, sperrylite in samples No.2 and No.3 is closely associated with magnetite. Palladium occurs in diverse ways. It occurs in the form of several Pd minerals (e.g. sudburyite, testibiopalladite, merenskyite), as a replacement for Ni in several tellurides, antimonides and tellurantimonides (e.g. melonite), or as very low concentrations in pentlandite (up to 34 ppm), chalcopyrite (up to 9 ppm), and pyrrhotite (up to 5.6 ppm). Palladium minerals and Pd-bearing minerals are strongly associated with chalcopyrite in sample No. 1 and will thus report to a Cu concentrate.However, 22% of the total Pd is in solid solution in pentlandite in this sample and will thus report to the Ni concentrate. In samples No.2 and No.3, less Pd occurs in solid solution in pentlandite, and the PGM are distributed mainly among pentlandite, chalcopyrite, and magnetite in sample No. 2, and among pentlandite, pyrrhotite, chalcopyrite, and magnetite in sample No.3. Therefore, the feasibility of magnetic concentration should be investigated for samples like No. 2 and No.3, in order to improve Pt and Pd recoveries. Rhodium was found to occur as rare hollingworthite, in sparse cobaltite (up to 2.7%) and, as low concentrations in chalcopyrite (to 10 ppm) and pentlandite (to 12 ppm) by proton microprobe. Iridium occurs in hollingworthite (up to 7.8%) and very rarely as the native metal or in an undefined Re-Ir-Qs..Ru alloy. Ruthenium was determined by proton microprobe analyses to occur in pentlandite (up to 13 ppm) and chalcopyrite (up to 10 ppm), in addition to rare laurite and Re alloy."

Jan 1, 1993

By R. P. van Hille, A. W. van Zyl

The BIOX® culture, aiding liberation of arsenopyrite/pyrite occluded gold, is inhibited by thiocyanate (SCN > 1 mg/L); precluding the recycling of tailings water up-stream of the bioleaching circuit. The activated sludge tailings effluent remediation (ASTERTM) process is a biological process that was developed to facilitate water recovery and treat waste water on-site (to achieve a SCN concentration < 1 mg/L) to be recycled or disposed of. The aim of this study was to investigate the effects of changing temperature and SCN loading on the SCN degradation ability of the mixed microbial population clue to seasonal temperature changes and fluctuations of SCN concentration in the waste water.

Jan 1, 2011

By A. Otsuki

"This paper discusses the primary collector adsorption onto a sulphide mineral in mixed collector systems to understand its adsorption mechanism. UV-vis measurements were performed to identify the primary collector concentration adsorbed on pyrite, and the adsorption kinetics under different conditions were compared to distinguish their difference between single and mixed collector systems. Small amount of secondary collector addition prior to the primary collector addition significantly improved the adsorption kinetics of primary one. The result was explained by the combination of two previously proposed mechanisms (i.e., different adsorption site mechanism and multi-layer product mechanism). This study showed UV-vis measurement as an effective tool to study mixed collector adsorption behaviour.INTRODUCTIONCollectors are surfactants composed of heteropolar molecules with a non-polar and a polar group (Lotter & Bradshaw, 2010). In a froth flotation process, the function of collector is to improve the hydrophobicity of target minerals and selectively float them with the aid of gas bubbles. Because of the chemical or physical attraction between the polar group and the mineral surfaces sites, collector molecules adsorb on the particle surface with the non-polar group assigned towards the bulk solution (i.e., water), thus the mineral particle surface becomes hydrophobic (Wills & Napier-Munn, 2006).Thiol collectors are major collectors widely used in sulphide mineral flotation. Potassium amyl xanthate (PAX), dithiocarbamate (DTC), dithiophosphate (DTP), mecaptobenzothiazole (MBT) are some common thiol collectors. Previous studies reported that some mixed collectors systems enhanced the flotation performance (e.g., Bradshaw, 1997; Bradshaw et al., 1998; Rao & Forssberg, 1997). Thiol collector mixtures are often used in the flotation of sulphide ores, and discussed with the synergistic benefits (Bradshaw et al., 1998) which include lowering the total collector dosage requirements, improving the sulphide recovery and the rate of flotation as well as the improving the froth characteristics. The current paper mainly considered the mixture between two thiol collectors (PAX and DTC, considered as a weaker and selective collector, and stronger and less selective collector, respectively (Bradshaw, 1997)) to further understand their adsorption mechanism that should assist in improving the flotation performance of refractory gold ore."

Jan 1, 2016

By F. Hassani, D. O’Donnell, M. Momayez, P. Guevremont

Shotcrete is a practical and economical support system in many Canadian underground mines. Although shotcrete technology has gained acceptance in the mining industry, there are some problems that have emerged with respect to quality assessment and thickness measurement of the liner. This paper presents recent tests performed with miniature seismic reflection technology (MSR) developed and patented at McGill University primarily for thickness measurement of this heterogeneous liner. MSR is also capable of providing information regarding the quality of shotcrete in terms of its mechanical properties such as modulus of elasticity and Poisson’s ratio. Work was performed on site in an underground mine in Ontario, Canada. This paper also presents the results from laboratory tests performed on fiber-reinforced and non-reinforced shotcrete panels that were used to assess the P-wave velocity in both materials. The results of these tests were used in a second site investigation. The NDT thickness measurements showed good agreement with direct thickness measurement such as coring. In addition, the MSR technology has the advantage of being more accurate and more affordable compared to other non-destructive testing (NDT) systems in the market.

Jan 1, 2002

By G. Sedelnikova, D. Kim, N. Ibragimova

"The object of this study was three samples of sulfide old tailings, which were obtained after Cu- Zn ores processing. Fine metal dissemination in sulfides as well as fine mineral intergrowth determine the refractory nature of material and low metal extraction using simple methods: gravitation 1-6%, flotation 32-48%, cyanidation 10-37%, and cause the need to use sulfide bio-oxidation to liberate gold and to recover it by heap leaching. The gold is the main valuable metal in the tailings with content 1-1.5 g/t. Heap bio-oxidation with mesophilic and moderately thermophilic bacteria was used for pre-treatment of tailings before gold heap leaching from bio-oxidation solid residues. The tailings have a low permeability < 0.3-1.2 m/day, which is caused by migration of fine particles, decreases recovery rates, and is poorly suited to heap bacterial leaching. Therefore, preliminary gold sulfide tailings with permeability < 0.3 m/day were pelletized using copper containing flotation tailings of converter slags and calcium oxide. The most gold extraction was obtained for pelletized tailings. The base metals (copper and zinc) were precipitated from bacterial solutions. Experiments have demonstrated effective bio-oxidation of all third gold sulfide tailings samples and enough high gold extraction 60-82%.INTRODUCTIONIn Russia, as everywhere, there is a trend toward deterioration in the quality of mineral resources, including non-ferrous and precious metals, manifested in lower grade and higher complexity of ores. The proportion of refractory ores is increasing, characterized by fine dissemination of metals in sulfides, intergrowth, and poor liberation of minerals during concentration, resulting in loss of base and precious metals to flotation tailings.Over the operation period, huge reserves (hundreds of million tons) of ore processing waste have been accumulated at mining and concentration operations. Because of the imperfections of the previously used ore concentration technologies, the content of precious and base metals in flotation tailings is comparable with the grades of the ores being currently processed. Therefore, old tailings can be viewed as an additional reserve of non-ferrous and precious metals. The works (DEN, 1997; Lyman, Johnson, & Guerney, 2000) demonstrate that, tailings containing sulfides (sulfur, copper, zinc, and other metals) are a potential environmental hazard since they produce acid drainage water containing toxic components. Processing those tailings would require designing an effective technology for recovering useful components and protecting the environment."

Jan 1, 2016

By E. Burdukova

Long-chain primary amines are utilized as collectors in potash ore flotation. Krafft temperature of long-chain amines in brine is about 100 °C, and this makes such amines practically insoluble in brine at room temperature. When dodecylamine, melted at 70 °C and dispersed in hydrochloric acid (or acetic acid) aqueous solution, is added to a KCl-NaCl saturated brine at room temperature, the amine precipitates. The experimental results demonstrate that the precipitating amine hydrochloride particles are selectively abstracted by KCl particles, but not by NaCl particles.

Jan 1, 2009

Gold recovery from refractory ores can be very difficult and complicated depending on the causes of the refractoriness. Typically, a fine wind and/or the oxidation of the gold-bearing sulfide minerals are required to liberate gold from the host rock matrix. Mineral separation techniques, particularly surface¬wettability based separation (i.e., flotation) and magnetic separation, can be used to pre-concentrate the gold and sulfide minerals, or to remove mineral species that are harmful either to the oxidation of the gold-bearing sulfides or to the cyanidation following the oxidation. In this paper, several processes are described, including oil-agglomeration flotation recovery of fine-grained gold and sulfide, reverse flotation of carbonate minerals prior to pressure or bio oxidation, reverse flotation of elemental sulfur after pressure or bio oxidation but prior to cyanide leaching, and magnetic concentration of gold-bearing iron oxides. The integration of these techniques with gold hydrometallurgical processes may make the economic recovery of gold from an otherwise uneconomic refractory ore possible.

Jan 1, 2011

By Imre Gombköto, Barnabás Csoke

"Raw material management means not only mining and processing of primary raw materials like ores, but means also collecting and processing secondary sources of raw materials. Recycling is one of the most developing field of raw material management in Europe, and its solutions are derived from mineral processing roots and principals. Complexity and challenges of the field of recycling results innovative solutions of material processing- Since European Union identified 20 raw materials as critical (CRM) due to lack of primary sources within the border of the EU, recycling become more recognised as source of different raw materials. WEEE is the waste streams contains many of the critical elements and along them at least 15 different species of plastics of which recycling is delayed by a lack of effective separation technique. Most paper deals with separation methods based on different specific gravity, triboelectric charge or surface properties of plastic species. Plastics however have differences of thermal properties and thermoplastics, duroplasts and elastomers can be recognised. The experiments described in the paper aimed to determine thermo adhesive behaviour of plastic species often identified in WEEE streams for separation purposes. According to the results, some plastic types as PS, PP. PC or PVC and PET pairs are possible to easily separate from each other, however different additives are changing thermo adhesive properties of most of the plastics that makes industrial process difficult to develop. Along thermo adhesive behaviour, combination of physical interaction can be used to enhance separation selectivity.INTRODUCTIONPlastics has a relatively long term of history as a light, multi-functional material in construction, packaging, automotive industry and electric and electronic products. There are a numerous types of plastic species can be used for various applications therefore they amount are growing from year to year. This quantity however become part of the waste stream and while metal recycling has been done for decades due to its economic value - cheap plastic parts are less desirable as secondary products. In 2013 an annual 5% of plastic production growth has been estimated with a base data of 265 million tonnes at 2010 (Guiqing & Zhenming, 2013). Since landfill requirements are increasing while—especially in Europe where actual regulations are trying to deflect waste from landfills - landfill capacities are decreasing, costs are become more and more expensive, Applications like energy production based on plastics as a fuel or recycling are some of the options can be applied. Direct incineration of plastics are applied at many plants - in most cases where waste consist of dangerous substances are incinerated because plastics high calorific value helps correct average mixture composition enable operators reaching high enough temperature for combined power and heat generation while most of substances—like PAH, PCB or dioxins—are destroyed. Another path is using low temperature reductive cracking due to pyrolysis process, however the chance having higher concentrate of carcinogen substances in the products are higher since it applies around 400°C during the process."

Jan 1, 2016

By William H. Emling

With profitability pressures in heavy industry increasing, many producers are turning to predictive maintenance as a means of harvesting untapped value from their production assets. Corporations are losing their maintenance and processing core competencies through attrition. As capital budgets are being trimmed, manufacturers are consolidating operating units into fewer, more profitable routes. Maintenance functions, however, typically receive low priority when investment is made, since many companies consider maintenance costs as ?overhead?. Condition-based monitoring, integrated to Level I and Level II process inputs, is seen as the most cost-effective solution to the implementation of predictive maintenance strategies. This paper will review the evolution of preventive and predictive maintenance programs, highlighting examples of successful application of integrated condition monitoring.

May 1, 2001

By J. D. McFarlane, V. Robinson

"The paper begins with a brief account of the naturarly occurring resources of gypsum and anhydrite and a discussion of their relative value and utility as sources of sulphur. The fundamental chemistry of recovering sul-phur values from calcium sulphate is discussed. (a) Thermal decomposition -discussed as impracticable; (b) Reduction to calcium sulphide; (i) Total Reduction-The chemistry is outlined and the Dorr-Oliver and Bureau of Mines processes mentioned. The Elcor process is mentioned and certain deductions made from available information.(ii) Partial Reduction-This is stated as the basis of the only proven process, namely ""The Cement -Sulphuric Acid Process."" The possibility of recovering lime is mentioned as an aside, but dismissed for lack of commercial application. The history of the cement -sulphuric acid process is covered briefly and a list of plants in commercial operation included. A brief elementary account of the basic chemistry of cement production is followed by a discussion on raw materials and fuels. A short account of the flow scheme of a typical plant, with notes on the operating peculiarities, precedes an account of product quality. The latest developments which enable by-product gypsum to be used as a raw material are discussed, with an indication of how the flow scheme is modified. A statement of feasible plant capacities is followed by requirements of raw materials, services, labour, etc., and finally some indication is given of capital costs."

Jan 1, 1969

By Jan Drzymala, Przemyslaw B. Kowalczuk

"Flotation is possible when the forces operating between a bubble and the attached particle are properly balanced. There are many forces operating in the bubble-particle aggregate. The magnitude, location and direction of the forces depend on the type of process. The simplest arrangement in flotation is when a spherical bubble is attached to a spherical particle and both are immersed in water. In such a system there are four essential forces which shape the stability of the bubble-particle aggregate. They are excess pressure and interfacial solid/liquid, solid/gas and liquid/gas forces. A proper analysis and balance of the size, location and direction of these four principal forces lead to a general equation delineating the stability of the spherical particle–attached bubble system. Specific cross sections of the system and solution of the general equation lead to different relationships including the Young formula as well as the well-known geometrical relation between contact angle, particle and bubble radiuses. The arrangement of forces in the proposed graphical representation of the Young law is different from that presently used in literature for a bubble attached to an unmovable solid particle. Many real solid/liquid/gas systems are more complex due to the presence of additional forces which change the regular curvature of the liquid/gas interface leading to advancing and receding contact angles.INTRODUCTIONThere are numerous papers (Athukorallage, Aulisa, Iyer & Zhang, 2015; Chau, Bruckard, Koh & Nguyen, 2009; Drzymala, 1994; Lubarda, 2012; Pellicer, Manzanares & Mafe, 1995; Wang, Cui, Zhou, Xu, Sun, & Zhu, 2014; Young, 1804) and books (Davies & Rideal, 1963; Defay & Prigogine, 1966; Lee, 2013; Lyklema, 2000) dealing with the solid/liquid/gas system. Many of them concern the three involved phases having the shape of a sphere or spherical cap and the formed contact angle. The contact angle is usually measured through the liquid phase and can be either smaller or greater than 90o. The essential part of these publications is a graphical representation of the system with the Young equation shown as a result of balance of only three forces that is the excess Gibbs (or Helmholz) free energy per unit area of the three involved interfaces (Davies & Rideal, 1963; Defay & Prigogine, 1966; Israelachvili, 1985) (Figs. 1a-c). The Young equation, when the gravity force/buoyancy is neglected, is:"

Jan 1, 2016

By J. A. Finch, M. Mimezami, M. S. Hashemi A.

The adsorption of magnesium and calcium ions on sphalerite and pyrite is discussed. These ions are common in process water and often considered be detrimental in sulphide flotation. The study attempts to characterize the adsorption mechanism, which has been less studied than the oxide system. Generally for oxides metal ion uptake occurs when cations are hydrolyzed. Our findings reveal that magnesium and calcium adsorb on sulphides at pH below hydrolysis, but adsorption is not chemical. At higher pH, charge reversal occurs that does correspond to presence of hydrolysis products. Advances

Jan 1, 2009

By Z. Trojanová

The deformation behaviour of ternary magnesium alloys AJ (Mg-Al-Sr) and AX (Mg-Al-Ca) were investigated in tension as well as compression tests. The samples were deformed at temperatures between 20 and 300 °C and at an initial strain rate of the order 10-4 s 1. The flow stress decreases with increasing temperature. The macroscopic work hardening rate decreases with increasing flow stress and temperature. The stress and temperature dependence of the work hardening rate is a result of the hardening and softening processes. Stress relaxation experiments were performed in order to reveal features of the thermally activated dislocation motion. Internal and effective stress components of the applied stress were estimated. A decrease in the internal stress was observed at elevated temperatures, which indicates recovery process (-es). A more detailed analysis of the estimated values of the activation volume and activation energy helped to interpret the thermally activated processes during plastic deformation. It is concluded that the deformation behaviour of the alloys depends on the activity of non-basal slip that is strongly influenced by temperature.

Jan 1, 2007

By Pingyang Zhang, Caichu Xia, Shuwei Zhou, Yu Zhou, Yongsheng Hu

A lined rock cavern (LRC) is an alternative container for compressed air energy storage (CAES) to store high-pressure air that is later used to produce electricity. A critical requirement of CAES in LRCs is that the inner seal should provide adequate sealing capacity to prevent air leakage from LRCs. In many studies, rubber sheets are applied to build the inner seal. However, air leakage through rubber seals has not been given much attention and rubber seals are usually assumed to be absolutely airtight. Given that rubber is permeable especially under high air pressure, such as in CAES, air therefore leaks through rubber seals during CAES operations. In this study, a numerical analysis was conducted based on the permeation equation of polymers and the governing equations of thermodynamics of CAES caverns to analyze the characteristics of air leakage from CAES caverns through rubber seals. A planned CAES plant in China was considered as a case study. Results show that air leakage rate increases with increasing cavern temperature and pressure during air injection and decreases as cavern temperature and pressure decline during air withdrawal. However, in total, the daily air leakage percentage is in the order of magnitude of 10-3% in a typical operation cycle, which is much smaller than the critical value of 1%. Under a common range of realistic operations conditions, the daily air leakage percentage is still of the order of 10-3%. Therefore, rubber seals can be used to prevent air leakage in LRCs for CAES. However, the experience of Japanese pilot cavern indicates that the specifications for the on-site vulcanization jointing and installation methods of rubber seals still need improvement.

Jan 1, 2015

By A. -I. Abenhaim, I. Sasu, C. Perron, I. Mantegh, S. Larose

Manufacturing long shafts, such as those used in turbine engines, normally involves with drilling inside them in order to take the excessive mass out. Concentricity between the shaft axis and that of the drilled hole is very crucial as it impacts the mass distribution around the axis of rotation. It is important that the shaft mass be well balanced around the central axis in order to minimise the centrifugal forces on the bearings and supporting structure as well as any unwanted vibrations. The eccentricity problem, mostly in long shafts, comes due to machining limitations. It is difficult in long shafts to maintain the concentricity tolerances while drilling inside the shaft. In this work, we address the problem of correcting this eccentricity problem, i.e., when the axis of the inside hole deviates from the central axis. The presented work is based on a threepoint bending method and investigates its effect on the residual stresses and plasticity regions induced on the shaft. A full finite element model is presented that can used to design the solution parameters (bending load, location, etc.) and predict the effect. Limited experimental results are also presented to validate the finite element modelling.

Jan 1, 2006