Search Documents

By M. S. Moats, C. M. Campbell

Samples of a high impurity (90.05 wt. % Cu, 4076 ppm Pb, 1939 ppm As and 635 ppm Bi) commercial copper anode were characterized and then electrorefined in a laboratory scale cell. Anode inclusions were examined using backscatter mode scanning electron microscopy and energy dispersive spectroscopy. Hundreds of inclusions were measured for size, morphology and composition. Commonly found inclusions were copper oxide (Cu2O), complex oxides (Cu-Pb-Bi-As-O) and copper selenides/tellurides. The weight percent of lead and arsenic increased with increasing inclusion size up to 4- 5 microns. During electrorefining, starter sheet ductility was negatively impacted by thiourea addition. The importance of arsenic (V) concentration on the electrolyte concentration of bismuth was observed. INTRODUCTION Copper electrorefining is a commercial process used to produce the majority of the world’s refined copper. During this process, impure copper anodes are dissolved electrolytically, and high purity copper is deposited on cathodes. As the anodes dissolve, the impurities either accumulate in the electrolyte or report to solids that form on anodes surfaces or at the bottom of the refining cell. These solids are called slimes. Slimes contain precious metals and are collected for further processing. Slimes are also an important outlet for problem impurities such as lead, antimony and bismuth. The electrorefining process is operated in such a way to encourage the deportment of these elements to the slimes. Impurities in copper anodes have been studied extensively by Chen and Dutrizac (1990, 1993 and 2005). The most common impurities found in modern copper anodes include: Ag, As, Au, Bi, Fe, Ni, O, Pb, Sb, Se, Sn and Te. Impure copper anodes are produced by pyrometallurgical methods and have purities ranging from 97.7–99.7% Cu (Moats et al., 2019). The composition ranges of commercial copper anodes from the 2019 worldwide tankhouse survey are given in Table 1. The concentrations of anode impurities vary widely dependent on the source material and prior processing steps. Based on the work of Chen and Dutrizac, both gold and silver are predominantly found in solid solution within the copper grains while a minor amount of Ag can be found in Cu2(Se/Te) inclusions. Nickel is entirely soluble within the copper grains up to anode compositions of 2500–3000 ppm Ni; above which NiO and kupferglimmer phases are formed (Chen & Dutrizac, 1990). As, Bi, Pb and Sb are found in solid solution within copper and within oxide inclusions typically found along grain boundaries. Oxides are formed due to the presence of 0.13-0.18 wt. % O (Chen & Dutrizac, 1990). This is because during solidification of the cast anodes, impurities are enriched in the liquid phase as the copper grains nucleate and grow. The inclusions form from the last liquid to freeze, which is typically along grain boundaries (Wenzl & Filzwieser, 2007; Wenzl, Filzwieser, Mori & Pesl, 2008).

Jan 1, 2019

By Ryan W. Siggelkow

Mines today use various methods of mining to extract ore. Because of the dangerous nature of many of these processes, remotely controlled LHD machines are being used to extract the ore from the draw point. The remote control system, although being made safer all the time, has remained virtually unchanged for many years. The basic functionality is an operator switching the machine to remote control, getting out of the cab, walking up a stand, operating remotely, returning to the cab, switching to manual, driving manually, switching to remote, and switching to manual. It seems repetitive, and time consuming, does it not? Networking, convergence, video, voice, and data infrastructures, and other technologies are growing by leaps and bounds in virtually every industry and region, except for mining. From the comfort of the living room couch, a Canadian can play hockey online with full voice conversations over the Internet with someone in Russia in real time. Yet, a mine superintendent must jump through hoops to have a private conversation with the front line supervisor underground. "Is Joe around anywhere?" If Joe hears the message, he will respond. If not, who knows? Maybe he's hurt. Maybe he's not. Where is Joe? Nobody really knows, and that is scary. Today, surface knows that the workers disappeared into the cage at 7:00 a.m. They also know that the workers will probably and hopefully return at 3:00 p.m. Is there not a better way to handle this? With such a complex industry, it seems as if, for the most part, the introduction of new technology into mining has either been overlooked or has been met with some resistance. It is time to step back, look at the process, and see how it can be improved. Key areas of focus will be safety, productivity, dependability, and cost-effectiveness.

Oct 1, 2010

By G. M. Brownell

A DEPOSIT of hematite occurs on Black island, lake Winnipeg, at a point known locally as Red Rock, on the south shore of the island directly across from Clements point. The mail boat from the Canadian Pacific Railway terminus at Riverton, crossing the lake to Manigotogan twice weekly, passes near Red Rock and provides a convenient means of transportation to this part of Black island (Figure 1). HISTORICAL The occurrence of hematite on Black island has been known for a long time. Dowling's report of 1898 states(1): "An iron-ore deposit on the south side has been known' for many years, and on Jeffrey's map of 1762, showing Canada and northern part of Louisiana, Iron island is shown a short distance south of the narrows, evidently the same as the Black island of today".

Jan 1, 1945

By Kan Xing

This paper introduces common detrimental consequences to the environment from mining in the Beijing West Mining Area. For example, ongoing mining operations can cause the following environmental deterioration: rock burst, roof rises, roof falls and inrush (Pit dash for ward water). Post-closure, after minerals resources are exhausted, the following environmental issues may remain: landslides (collapse, and mud-rock flow), dropping or exhausted water tables, water pollution, desertification and soil erosion, water accumulation, Slay endanger, ground subsidence, and causal factors in seismic activity. This paper analyzes this wide range of environmental consequences of mining, and offers a theoretical foundation to underpin a corresponding management scheme.

Aug 1, 2013

By N. Shi, T. G. Joseph

ABSTRACTA series of algorithms were developed to perform geometric and kinematic analyses of cable shovel dipper-ground interactions for a given set of mining face conditions. The routines examine and analyze (a) the position of the dipper in relation to the shovel; (b) the dipper in relation to the face conditions; (c) the dipper position in relation to possible interference or collision with crawler tracks during digging cycles; and (d) kinematic and geometric considerations with respect to any point on the dip-per as it conducts a duty cycle. In all cases, field measurement verifcation provided good agreement(within 4% variance).

Jan 1, 2011

By R. H. McCorkell

"Sample drops were evaporated on Lexan disks on which fission tracks were etched and counted after neutron irradiation. [U] = 0.01 ppb could be measured. This method is rapid, cheap, simple and accurate when sufficient control and checking is possible, but several types of error were encountered in its use, the natures and sources of which were investigated but not always determined. The most troublesome were ""annealing"" processes which sometimes altered the fission tracks so that they were not fully revealed, or acquired varying appearances, after etching. Several different annealing processes seemed to exist and seemed to be produced by alteration of the Lexan surface by dissolved components in the solutions and, perhaps, by radiation and local heating during neutron irradiation. The appearances of the etched tracks varied with the natures of the droplet solutions even when annealing appeared to be absent, and for this reason, standards are best prepared by additions of known amounts of U to sample solutions. Contamination of sample droplets by U-containing dust from the air is best avoided by preparing the disks away from areas where other U-analysis is being carried out.IntroductionFission tracks are regions of radiation dam age produced in solids by the fission of atoms such as 235U. They can be enlarged to sizes visible through optical microscopes by etching surfaces through which they pass with solvents in which the solids are slightly soluble. A sample to be analyzed for U may be placed against a film of a solid of negligible uranium concentration (the track detector) and irradiated with thermal neutrons in a nuclear reactor to fission 235U. The track detector is then etched and the number of tracks per unit area, ?, which is proportional to the uranium concentration of the sample, c, and the neutron do se, n, is found by counting through a microscope. Uranium in solutions ha s been measured by evaporating drops on track detectors, irradiating, etching and determining the number of tracks per drop, T(2,3,4,5). Extensive test s of this method are reported here."

Jan 1, 1983

By E. Norton

"Even though the subject of this panel discussion is dust control, rather than dwell on the design aspects of dust collection systems which are well documented in numerous publications, :it was considered more pertinent to the present economics of mining to examine the energy costs involved.At the present time, the facts of shrinking fossil fuel reserves and spiralling fuel costs are being constantly brought to our attention. Industry is being motivated to consider the possibilities of incorporating heat recovery systems in areas where they prove to be economical. Unfortunately, it is not a simple exercise to determine if the installation and operation of heat recovery equipment is feasible and economical. Each process involving heat recovery potential must be thoroughly studied in all aspects.In a paper presented at the 1975 Annual General Meeting of the Canadian Institute of Mining and Metallurgy in Toronto, Ontario, entitled ""The Influence of Energy Conservation on Concentrator Design"", it was stated that the largest single energy consumer in winter is space heating with the largest portion of this supplied to crushing and screening plants. (1) Within the scope of this panel discussion we will study, as one example, a crushing and screening plant using natural gas heat in the province of British Columbia and we will explore the feasibility and economics of installing air-to-air heat recovery equipment."

Jan 1, 1976

By Kenta Kusunose, Dadang Sundana, Ahmad Munib Fikry, Yosuke Unno

PT Smelting has operated the Mitsubishi Process in which feed materials are charged into the S- furnace through top lances using a pneumatic conveying system comprising 6 feeding tanks (S-Feeding Tanks). Each S-Feeding Tank was designed as a batch machine and had been operated in a batch mode so that feed materials are conveyed 70% of the operating time (conveying time). An S-Feeding Tank was revamped in August 2016 in order to attempt to achieve 100% conveying time during operation, aiming to reduce the furnace draft fluctuations and melt temperature fluctuations leading to reduced copper losses to slag and refractory wear on the sidewall in the melt zone. After two-year operation with some adjustments and modifications, it was concluded that the new system works as expected. During scheduled major shutdown in November 2018, the same modification was applied to all other 5 feeding tanks as the first one, while several modifications other than the S-Feeding system were also conducted for the purpose of expanding the capacity of the smelter. INTRODUCTION PT. Smelting (PTS) Gresik Copper Smelter and Refinery is located 30 kilometers north of the city of Surabaya, East Java major port. PT Smelting equity partners are Mitsubishi Materials with 60.5%, PT. Freeport Indonesia with 25%, Mitsubishi Corporation RtM Japan Ltd. with 9.5% and JX Nippon Mining and Metals corporation with 5.0%. PTS was established in February 1996 and started commercial operation of the Mitsubishi Process in 1999. The Mitsubishi Process is a unique technology which connects 3 stationary furnaces, namely the Smelting furnace (S-furnace), Slag-Cleaning furnace (CL-furnace) and Converting furnace (C-furnace) by covered launders. These features result in savings in manpower and energy, and make the process more environmentally friendly since there is no ladle transfer of melt. Figure 1 illustrates the outline of the Mitsubishi Process.

Jan 1, 2019

By B. R. Conard

Occupational epidemiology of the nickel-producing industry has found that inhalation exposures to certain nickel-containing substances are linked to respiratory cancers and to nonmalignant respiratory endpoints. Establishing such a linkage, however, is complicated by the fact that some diseases occur long after exposure to a causal agent (i.e., some diseases have long latencies). Furthermore, most chemical agents (especially nickel substances) vary significantly in their toxicological properties and their concentrations in workplace air have varied over processing history. Because of these complications, it is critical to understand historical exposures to specific nickel substances. To assist in this effort, the author focuses on the history of smelting and its related processes at Vale Canada’s (Inco’s) Ontario operations in the first half of the 20th century.

Jan 1, 2012

By L. I. Kiss, S. Perron, D. Toulouse, S. Poncsák, A. Perron

Bubbles play an important role in many industrial processes. In a Hall-Heroult cell, used for aluminum production, bubbles contribute to induce flow in the cell. The induced flow is important for the thermal balance of the cell as well as for the distribution and dissolution of the alumina. The existence of the bubble layer does not have advantages only. It increases the voltage of the cell and causes deformation along the cryolite-molten aluminum interface. The role of the anode inclination in the behaviour of the bubble layer as well as in the hydrodynamics of the bath is not clearly understood. In this work, the effect of the anode inclination angle on the bubble driven flow is studied in an industrial scale air-water model. The inclination angle is varied up to 5° from the horizontal. The instantaneous flow field is captured by Particle Image Velocimetry (PIV) system. The mean velocity fields were calculated by ensembleaveraging the instantaneous velocity fields measured at different time. The existence of the counter-flow in the interpolar space and the vortex in the side channel has been confirmed. Furthermore it has been observed that the effect of anode slope on the velocity field is weak.

Jan 1, 2006

By E. Heikkinen, J. Suikkanen, T. Siren, J. Valli, M. Hakala

Diametrically faced borehole breakout observations are a fairly good indication of magnitude of the secondary stresses acting perpendicular to the borehole. In cases of low in situ stresses, where borehole breakouts are not observed naturally, it is possible to increase the prevailing stress state around the borehole by increasing the rock temperature. When the temperature is increased sufficiently, thermally induced borehole breakouts will occur. By implementing the temperature increase in boreholes located at excavated tunnels, it is also possible to study the effect of the near-field stresses caused by the excavation. The near-field stress state changes as a function of borehole depth, thus increasing the information available from experiment. To study the feasibility of this proposed low cost method, a Borehole Thermal Spalling (BTS) experiment was executed in ONKALO Underground Rock Characterization Facility, in Western Finland in 2014. The first borehole pilot test with the method was conducted in ONKALO at the POSE niche in already at May 2010, with the second pilot test following in August 2010 at Äspö HRL. The major objective of the experiments was to define the trend of the maximum in situ stress component, while also providing knowledge of the in situ spalling strength of the ONKALO rock mass. The stress state in ONKALO is nearly isotropic in horizontal layer, causing problems for the use of more traditional stress measurement methods. With boreholes heated over long interval, the weakest rock parts are observed to fail, thus providing statistical confidence. For these reasons, continuous test sections have an advantage in ONKALO, compared to spatially limited stress measurement methods such as overcoring and hydraulic fracturing. The BTS experiment is conducted in 9 meter deep vertical boreholes located at the POSE niche, situated -345 m depth below the ground surface. The boreholes used within the BTS experiment are located in migmatitic granite, in an experiment area where the surrounding stress state and the rock strength are fairly well known. The prior knowledge of the stresses is favourable for the experiment, as it requires careful planning and iterations to determine the appropriate heating power domain. Too low heating power will not be sufficient to cause borehole breakout, while too high heating power causes breakout in all directions thus making determination of stress direction hard or impossible. The initial state of the borehole and induced borehole breakouts will be monitored using acoustic televiewer logging (ABI) and optical borehole logging (OBI) imaging techniques. Fracture mechanics modelling is used in planning of the experiment, also in back-analysis to link the observed breakout angle to stress state. Both the pilot test in 2010 and BTS test in 2014 resulted in similar borehole breakout direction. The results are in line with so called EDZ & VT1 stress interpretation, revealed the maximum horizontal component bearing the magnitude of 21.5 MPa, with the trend of 166°.

Jan 1, 2015

By M. Sukhram

This paper presents a technique to determine the direction of velocity in liquid aluminum (Al) by measuring the temperature distribution within a cylindrical rod while it is inserted into the flow. The heating pattern of the rod is a result of the interaction of the thermal fields of the rod with the liquid Al. This interaction freezes aluminum onto the cylinder in a characteristic pattern and as a result the temperature response within the rod also follows a distinctive heating pattern. Monitoring the temperature within the cylindrical rod as a function of spatial and temporal coordinates, the direction of velocity can be inferred. Experimental research work involving liquid Al was conducted at the University of Toronto using the Revolving Liquid Metal Tank (RLMT). The RLMT is a resistance furnace which can hold up to 50kg of liquid Al. In this RLMT tangential velocities up to 0.35m1s can be generated. Experimental data for different superheat and magnitude of velocity demonstrate that the sensor records different heating patterns under different fluid flow conditions. Using the transient temperature information, the direction of velocity of the molten Al flow field can be detected.

Jan 1, 2011

By V. G. Papangelakis, G. A. Moldoveanu

"One of the major commercially viable secondary sources of rare earths elements (REE) are the ion-adsorption ores, containing 0.05-0.3 wt% rare earth oxides physically adsorbed on the surface of clay minerals formed during weathering of lanthanide-rich rocks. Although ion-adsorption deposits are substantially lower grade than other types of rare earth sources, this is offset by the easier mining and processing costs and the low content of radioactive elements. The conventional extraction route involves ion exchange leaching with monovalent cation solutions (usually ammonium sulphate) under ambient conditions; during the process, the lanthanides are desorbed and transferred into solution, being replaced by the exchange cation. While ammonium ions are known to perform best, there is increased environmental motivation to investigate alternative lixiviants in order to minimize ammonium sulphate impact via reducing its use without considerable loss in rare earth recovery.The objective of the present research was to screen various cations salts (alkaline and alkalineearth metals present as sulphates, chlorides and acetates, respectively) in order to comparatively evaluate lanthanide desorption levels and provide a theoretical base of the observed behaviour. The overall aim is to gain a better understanding of how both cation and anion may affect the overall REE recovery from ores in order to provide alternative processing routes. The distinct exchange capabilities of cations were explained in terms of differences in cation hydration enthalpy within the same group, i.e. Cs+ > NH4 + > K+ > Na+ > Li+ and Ba2+ > Ca2+ > Mg2+. For the same cation, it was determined that REE extraction efficiency follows the order sulphate > acetate > chloride, based on dissimilarities in constants of formation values. Various process implications scenarios will be described based on using mixed cations and anion matrices."

Jan 1, 2016

By A. C. Hatton

Doped SrCoO3.8 was found to be a promising material for use as a cathode component in intermediate temperature SOFCs. In this work, strontium cobaltite ceramics doped with 10 mol% to 90 mol% samarium were synthesized using the glycine nitrate process in order to study the electrical conductivity and thermal expansion at temperatures of up to 800°C. As-synthesized powders were deagglomerated, pressed and sintered at temperatures ranging from 1100-1250°C. The effect of temperature and composition on electrical conductivity and thermal expansion are presented and discussed.

Jan 1, 2005

By G. Marchand, R. H. Hay, E. C. Pearson

"AbstractA polishing .technique is described together with two anodic etching methods for aluminum and its alloys. Some of the optical and structural characteristics of the film formed by •these etching methods are discussed and it is shown to what degree these properties of the film are related to the crystallographic orientation of the metallic substrate. Applications to the study of recrystallization and twinning phenomena and to the study of plastic deformation, banding, and texture estimation are discussed. Micrographs are shown .to illustrate the manner in which the technique is particularly well suited to the study of such phenomena.IntroductionThe physical metallurgist is constantly faced with the problem of polishing and etching of metallic sections. Mechanical polishing is tedious, time consuming, and not applicable whenever a surface entirely free from plastic deformation is required. Etchants are generally required to reveal the grain structure in order to determine its size, shape, and regularity, or to bring up constituents. In the case of aluminum, the .most common etchant to reveal grains is a mixture of three acids: HC1, HN03, and HF. This etchant is fairly satisfactory on certain alloys and for certain metallurgical conditions but in general fails to give a good definition of the grain on castings, on highly alloyed products, and whenever the grain is smaller than 100 microns in diameter. Besides size and shape, a grain, or crystal, has an orientation and may be endowed with several types of imperfections."

Jan 1, 1952

By C. Blawert

In spite of various corrosion studies on HPDC AZ91, there is no clear indication which microstructure gives the best corrosion performance. The skin with its fine microstructure is sometimes reported to have the best corrosion resistance, but there is no clear definition of the skin. If the skin is the outermost part of the casting and nothing is removed from it, then it is contaminated and the corrosion resistance is low. If the outermost skin is removed (about 25 µm) then a better corrosion resistance can be obtained. However this does not automatically mean that there is no other region in the bulk of the casting which could have a similar or even better corrosion resistance. Indeed, the corrosion measurements including potentiodynamic polarization and long term electrochemical impedance spectroscopy (EIS) revealed a lower corrosion resistance of the original as-cast skin about 100 pm thick. The thickness of this region is more or less independent from the thickness of the casting section. The surface region is free from any dendritic grain growth which influences the amount and distribution of the 13-phase and therefore the distribution of the most important alloying element Al. This could explain the different corrosion behavior. Further reason can be found in the enrichment of some impurities such as Fe in the near surface.

Jan 1, 2006

By G. Deschenes

"This literature survey discusses the recovery of gold from thiourea solutions. An overview of techniques used and general comments on the basic cyanidation methods are presented. The chemistry and mechanisms of cementation, activated carbon, resins, electrowinning, solvent extraction and pressure reduction are examined. Conclusions and recommendations give orientation for future research and development activities in this field.RésuméCette revue littéraire traite de la récupération de I ‘or des solutions de thiourée. Elle fait un survol de I ‘ensemble des techniques utilisées tout en introduisant des commentaires généraux sur la méthode classique qu'est la cyanuration. La cémentation, Ie charbon active, les résines, l'électroextraction, I ‘extraction par solvant et la réduction sous pression sont les méthodes analysées tout en considérant leur caractère chimique respectif ainsi que les mécanismes qui y sont rattaches. Des conclusions sont tirées et différentes recommandations sont suggérées pour orienter la recherche dans ce domaine."

Jan 1, 1986

By W. A. Jones

"The Ross mine, a subsidiary operation of Hollinger Consolidated Gold Mines, Limited, is near the north end of lot 1, con. II, Hislop tp., Ontario. The property comprises the north half of lot 1, con. II, and the south onethird of lot 1, con. III. It is readily reached by a good motor road from the village of Ramore, 7 1/2 miles to the southeast on the Ontario Northland railway. The mine is being developed to a depth of 1,500 feet, and the current daily production rate is approximately 300 tons. From the inception of operations in March 1935 until December 31, 1945, 692,000 tons of ore, with a total value of $5,762,685, was milled . The silver to gold ratio of 1.48 to 1 is unusually high for Ontario gold mines.TYPE OF 0REBODIES AND MINERALIZATIONThe orebodies consist of lens-shaped and pipe-like stringer lodes and tabular vein zones composed of parallel quartz stringers. The host rocks are steeply inclined eruptive breccias and tuffs, striking N.70°W., intruded by very small stocks of red syenite. The orebodies appear to be spatially related to an intricate system of fault planes. Hydrothermal alteration is widespread and is not zonally related to individual quartz stringers. The wall-rocks contain abundant fine-grained pyrite, but gold is confined to the quartz stringers.RELATIONSHIP TO REGIONAL STRUCTURELack of outcrops has prevented the detailed mapping of the Keewatin complex in the vicinity of the Ross mine with the degree of success that has been achieved in the Porcupine area.A northwesterly trending belt of slates and greywackes, bounded by faults, forms the central part of a broad anticlinal arch about 3 1/2 miles north of the Ross shaft. Lava flows forming the south flank of the structure face south toward the mine. If the sediments are to be tentatively correlated with the large areas of Keewatin slates and greywackes of the Porcupine area, it must be assumed that they are younger than the lava flows and that they have been down-faulted."

Jan 1, 1954

By Jason Berenyi

Presentation Overview ? What is Potash? ? Where are the potash deposits? ? Current potash mines ? production, capacity and planned upgrades ? Saskatchewan Saskatchewan?s Potash Production Potential s ? Current Status of Potash Exploration ? Increasing Demand for Potash ? Saskatchewan global role

May 1, 2009

By Mohammad Reza Khalesi, Ruhollah Rezazadeh, Mohsen Izadi Yazdan Abadi, Mahmoud Abdollahy

"The rotary vacuum drum filter (RVDF) is widely used for dewatering in mining industrial. In general, different parameters have influence in the solid-liquid separation such as: solid percent, level of vacuum, particle size distribution, filter cloth and chemical additives. These parameters can influence on some variables such as cake moisture, throughput and filter cloth life time. The aim of this study is to propose some chemical additives to improve the rate of filtration and decrease cake moisture of Gol-E Gohar iron ore concentrate by using laboratory scale bottom feed vacuum filter and suggest a filter cloth with long life time (more than 400 hours). Effect of particle size distribution on filtration investigated in large scale by measuring the thickness of cake and cake moisture.Increasing molecular weight of anionic flocculant lead to increases throughput but cake moisture increases too; While the filter aid increases throughput and decreases cake moisture simultaneously; the combination of them show different behavior. TSS and filter cloth life time have directly relation with material and type of filter cloth weave. Depending to type of feed, two polyester and polypropylene filter cloth are suggested. More over twill and satin weave have the best results. To prove the laboratory results some industrial tests performed in Gol-E Gohar hematite iron ore concentrate plant.INTRODUCTION“The process of grinding and classification involves the use of large quantities of water. The separation of solids from liquids is usually achieved by gravity sedimentation in thickeners. For fine particles this is a slow process. In general, 75–80% of the water can be separated and removed by thickeners. For further water removal, filters are used where in excess of 90% of the water can be removed” (Gupta, 2006).“Many types of filters are available, which are broadly classified here as vacuum, pressure, precoat and depth filters. Each classification contains a number of sub-processes. A category of filter that uses vacuum induced driving forces and semipermeable media to facilitate the separation of solids from suspension. While pressure differences across the filter are limited to less than 85 KPa (usually 75 KPa), most units are capable of processing a wide range of feed materials in a continuous manner” (Rushton, 2008)."

Jan 1, 2016