Search Documents

By T G. Callcott

Australian coking coals are either class 434<tlj534<2l, at Port Kembla, or 634<3> at Newcastle. The former yield good blast-furnace cokes; the latter yield poor ones. However, increases in conventional strength indices, by methods applicable with normal coking ovens, seem unlikely to be economically attractive. Characterization of the coals has enabled an "economic" blend to be developed in the Newcastle area, and this has affected mining, preparation and handling operations. Coking studies have led to a specification for the making of strong coke, especially from the high-volatile Newcastle coals. Continuous coking studies, developed from the efforts to make very strong coke, have taken two directions. Firstly, coking thin layers of coal on strands; secondly, coking, in various types of vessels, compacts of coals with or with-out the inclusion of non-coking coals, iron ores or other inert materials. Gas, "sand" and hot metal coking have been tested for use in compact coking. Particular attention has been paid to pellets of coal and ore. The probable industrial problems in adopting any of the ideas are presently being examined.

Jan 1, 1963

By J. E. Moyle

The costs of labour and electric power are of prime concern to almost all industrial enterprises, and various methods of reducing their impact on production costs are constantly being developed. Automation is one of these schemes, and has received a good deal of attention in the past few years. In the mining industry, compressed air is almost universally used, and its cost is significant. Although the compressor machinery now in use has achieved a high degree of development, the hazard of explosion and fire still exists in these systems. There is thus considerable resistance in some quarters to suggestions that such installations can be safely and successfully automated. The Milliken power plant consists of two 30,000 lb. /hr. fully equipped high-pressure boilers, four H.P. air compressors, a steam turbine for stand-by power, and several L.P. compressors and vacuum pumps. With the installation of automatic and protective equipment in the machinery section, the shift force has been reduced from three to two men.

Jan 1, 1963

By C. A. Ingram

The Cigar Lake ore body is a high-grade uranium deposit situated within water-saturated sandstone. In order to extract the uranium ore remotely, ensuring minimal radiation dose to workers, and also to access the ore from stable ground, the Jet Boring System (JBS) was developed. This method of mining involves drilling a pilot hole up through a frozen ore body and utilizing a high-powered water jet to mine out cavities. During the mining process an ultrasonic sensor will be used to provide feedback to the operator, who is located beneath the ore body, as to the dimensions of the cavity. However, more precise data is required to determine final shape, volume, and location of the cavity for mine planning purposes. Selecting a device that will provide sufficient range data in the challenging environment will be vital to optimizing the mining process. Major issues include fog build up and flying debris during mining, and an environment that is wet, dark, and cold A test cavity has been designed and constructed at the Saskatchewan Research Council (SRC) so that a study comparing three different technologies, as prospective candidates for the survey system, can be conducted. The devices being evaluated include a Senix ultrasonic sensor, an MDL Cavity Auto-Scanning Laser System (C-ALS), and a MESA Time of Flight (ToF) camera. The ultrasonic sensor is known to provide range data in foggy conditions but has low accuracy. The C-ALS has been developed for surveying remote cavities but is expensive and does not provide reliable data in fog. The ToF camera provides a high volume of data in a short time period, with potential to provide accurate information in extreme conditions, but has not been tested in a mine cavity application. Iterative closest point (ICP) registration is applied in an attempt to create a 3D point cloud from the scan data and to also compute rotation and translation of the ToF camera. This paper presents an overview of the challenges involved in conducting a survey within a JBS mined cavity, the analysis used to determine the suitability of each device, and the data collected from the test cavity.

Aug 1, 2013

By S. Koppalkar

ABSTRACT: The development and evolution of the gravity recoverable gold (GrG) test procedure at McGill university is reviewed in this paper. Since the late 1980s, the research group led by the late Professor André Robert Laplante at McGill university has undertaken fundamental studies and applied research of the Knelson concentrator to develop a sustainable method of estimating GrG. Historically, a concept of “free gold” was used, and it was de?ned as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, the practical use of amalgamation has declined. around 1994, a methodology using a 3-in Knelson concentrator to measure gravity recoverable gold was established at McGill university. as a result of more than 10 years of improvement and optimization, this technique has become a standard method of evaluating GrG for gold ores, gold plant streams and platinum group metals. By 2006, about 200 GrG tests were carried out at McGill universityon ores from all over the world. recently, a modi?ed version of the GrG test (a simpli?ed test) was developed to provide a quick and rough estimate of the GrG in a sample; this simpli?ed test has theadvantage of reduced mass, processing time and cost. to recognize and honour the contributions madeby the late Professor Laplante towards the establishment of a standard test procedure for assessing gravity recovery potential, the authors propose that the GrG test be named after Laplante.

Jan 1, 2010

By I. Paredes, R. Díaz, H. Henao

Smelting of copper concentrate generates a significant amount of dusts which are collected in electrostatic precipitators. This material, which is a complex oxide of Cu, Fe, S, As, Sb, Bi and others, is difficult to recirculate into the smelting process due to the reported high concentration of arsenic. However, the dust also has concentration of copper above 10wt %, aside from reported contents of silver corresponding as much as 25wt% of the total inventories of this element in the smelters. Thus, it is of economic and environmental interest the development of a process able to reduce the concentration of arsenic in the dust and produce a material suitable to be recirculated into the smelting process. The present experimental work shows the results of a process of dust sulfidization-oxidition able to remove more than 65wt% of the arsenic present. INTRODUCTION Copper sulfide deposits worldwide exhibit increasing concentrations of arsenic. One case of interest would be the copper ores from the northern zone of Chile, which report high concentrations of enargite (Cu3AsS4) (Revista química, 2015) (Latinominería, 2014). The obtained concentrate from this ore is treated in a Fluidized Bed Roaster, producing calcines with low concentration of arsenic (<0.5 wt% As). This material is suitable to be treated in a Flash Furnace. At the roasting process, the arsenic is volatilized and then precipitated as fine particles of complex oxides. Most of this particulate material is removed from the gas stream through a device called Electrostatic Precipitator (Minería chilena, 2014). The experimental results reported in the literature indicate that arsenic present in these particulate materials (or dusts) cannot be eliminated in oxidizing atmospheres (air) or with inert gases (N2) in a Fluidized Bed Roaster even at temperatures as high as 700°C. There is also information that even the recovery of valuable metals from the dust is difficult through hydrometallurgical processes (private communication). This is how in some foundries these dusts are considered environmental liabilities. Regarding the decomposition of enargite (Cu3AsS4) in neutral atmosphere, it is reported in the literature (Padilla, 2001) that the main chemical reactions are:

Jan 1, 2019

The Environmental Excellence in Exploration (E3) project is driven by the recognition that the minerals industry can only maintain its long term viability by ensuring its continued access to lands to explore for, and develop, new mines. Widespread implementation of sound environmental management practices by the exploration community and improved education and understanding of that by stakeholders will help substantially in accomplishing this, and E3 is designed to meet these needs. Exploration crews are now viewed as ambassadors for the global mining community. Their performance in managing the environmental aspects of an exploration program can demonstrate a commitment on the part of the international mining sector to environmentally responsible exploration and mining. We have all observed that failure to behave responsibly can alienate local residents, encourage anti-mining NGOs and jeopardize development. As the saying goes, ?you don?t get a second chance to make a first impression?, and we want to make a favourable first impression. The E3 project is focused on creating an electronic manual, the e-manual, which will provide rapid access to the most up-to-date information on environmental management practices for minerals exploration globally. The e-manual will reflect current thinking and practices in environmental management. It will be richly illustrated with actual examples that reflect the realities of exploration. It will strive to identify the key environmental issues and concerns that apply to most exploration projects, and identify other sources of relevant information useful to field practice. It is our belief that E3, or something very like it, is central to ensuring that the industry survives the current challenges to its viability. E3 will be a cornerstone of the mining industry?s drive to sustainability simply stated, if we are not permitted to explore for mines, there will be none of them at some point in the relatively near future.

May 1, 2002

By G. Wang, L. R. Moore, Y. Xiong, A. Gorken

"Mining is a very water intensive industry. As such, the industry has become dependent on applying alternate sources in efforts to minimize the impact on the locally available fresh water. Sources such as recycled water, sea water, and even acid mine drainage have been applied at some limited applications, while other mines may not even have the option of fresh water available in their region. However, the different sources of water will have varying concentrations and types of soluble salts and suspended solids, which can lead to dramatic differences in mineral processing when comparing these types of waters. Water quality is known to affect bubble generation and strength, mineral surface charge, and even reagent coordination properties. This paper focuses on the exploration of how water quality and soluble salts affect the flotation of iron and titanium containing minerals from feldspar, and the design of flotation collectors for optimal performance in this water.INTRODUCTIONFeldspar is defined as a tectosilicate mineral with the generic structure of MAlxSixO8, where M represents the cation (Celik, 2001). Feldspar is most often found naturally occurring with quartz, iron containing minerals (i.e mica), and titanium containing minerals (i.e. rutile). The alumina component of feldspar is of interest to glass making, while the alkali metal component is of interest to ceramics (Vidyadhar, 2002). In glass making, the alumina is known to improve product hardness, durability, and resistance to chemical corrosion. In ceramics, the alkalis act as a flux; a flux lowers the melting temperature of the mineral mixture, and assists in connecting the other components present in ceramics. Quartz is stated as having a negative effect on the melting point of the feldspar. Although quartz is typically not removed during the feldspar applications in the glass industry, it needs to be reduced for the ceramics industry. Iron and titanium based minerals are known to have negative effects on color and quality of the products in both glass and ceramics. Thus, these “contaminants” must be reduced to a certain product specification via feldspar beneficiation (Table 1)."

Jan 1, 2016

By A. Hasselbring

Sub-Level stoping was used in this country at least as early as 1912, at the Magpie mine in Michipicoten. The fundamental principles of the system are the same wherever it is used, but modifications have been adopted in the Michigan iron mines and in several Canadian mines. It is a system whereby a suitable body of ore may be developed quickly and worked cheaply, with a low initial expense, and by miners of quite ordinary ability. The basic method, described in the following pages, may be modified to meet conditions where one or more factors are not in accord with normal sub-level stoping requirements. In suitable ground, sub-level stoping is probably the most satisfactory method yet devised for underground hard-rock mining. It is so simple, straightforward, and safe that no special training of a crew is necessary. Any miner capable of drifting and raising can carry on the work necessary for sub-level stoping after the shaft has been sunk. The method is suitable, however, only for reasonably wide ore-bodies, the minimum width of ore to which it can be economically applied being somewhere in the neighbour-hood of thirty feet. The development programme is simple. Assuming, for purposes of illuslustration, an ideal ore-body, two thousand feet long, dipping nearly vertical, and varying in width from forty to a hundred feet, this programme would be as follows. The shaft should be sunk on the footwall side about sixty feet outside of the ore-body and near its centre. Levels are then established at suitable intervals, usually 125 feet. On each level, a cross-cut is run to the ore-body, and there a main-haulage drift is driven in either direction to the end of the ore. Cross-cuts are then run at 25-foot intervals, so that ore-chutes can be spaced about 25 feet centre to centre each way. It is not necessary that these cross-cuts be extended to the walls of the ore-body, if the position of the walls is known; they are extended just far enough to make room for the correct location of the chutes.

Jan 1, 1934

By E. W. Lucht

THE term "high pressure", as used in industry today, is applied rather loosely. Generally, it refers to pressures that are higher than those encountered in most industrial processes although no definite limits are normally stated. For the purpose of this talk I should like to set rather arbitrary limits to the term "high pressure", and in ab-solute figures this would be the range from 1000 psi to perhaps 40,000 or 50,000 p.s.i. The scope of high pressure technology is very broad, and it would take more time than we have avail-able here today to cover fully even one aspect of the field. Therefore, I should like to discuss just some of the techniques used and problems en-countered in high pressure operations. Research work into the high pressure region dates back about 150 years, but it was not until 1910 that the first commercial application of high pressure technology was made in the production of ammonia.

Jan 1, 1962

By J. S. Kirkaldy, W. J. Slater, G. R. Mason

Activation analysis for copper and manganese in 10 mg samples machined from aluminum-base diffusion couples has been used in the study of ternary diffusion in the Al-Cu-Mn system. The accuracy, economy and convenience of the method are considered to be very competitive with other methods for analysis of such small samples. Neutron-activated aluminum-zinc alloys in the range from 10 per cent to 100 per cent zinc have been equilibrated with a known volume and the vapors subsequently condensed and collected. The vapor pressures relative to pure zinc (the thermodynamic activities) have been determined at 550°C' by recording the relative count of /'-rays from zn65 in the collected samples. The method is a sensitive one, although subject to serious obstacles to experimental accuracy.

Jan 1, 1961

By G. Rong, W. Du

Stability of some potential unstable blocks in the left bank slope of Baihetan hydropower station is evaluated in this paper using the three-dimensional (3D) limit equilibrium method. The Baihetan hydropower station is in the downstream of Jinshajiang River, China. The geological condition in the river valley is complex, and many large discontinuities are detected in the slope of the two banks. As a result, much attention should be paid to the stability of the slope in the feasibility study stage. Because the left bank slope is an oblique consequent one, we mainly focus on the slope stability analysis in the left bank. Comprehensive geological exploration is conducted in the studied area and the detected discontinuities are well researched. By building a 3D geological model of the left bank slope, three potential unstable blocks which are close to the dam site are detected. An irregular wedge analysis method is then used to calculate safety factors of the three blocks under three conditions, which are natural condition, rainfall condition, and seismic condition, respectively. It is found that the safety factors of the block 1# and the block 2# are quite low when compared to the suggested values. Extra care must be exercised when excavating the slope near the block 1# and the block 2#. A preliminary reinforcement is also suggested.

Jan 1, 2015

By D. Emadi

The ASTM B108 Mould and a Modified Mould were used to cast test bars under a variety of conditions: mould and pouring temperatures, mould coating and tilt. Mechanical properties were determined in the as-cast and heat-treated conditions. The ASTM Mould is less sensitive to casting variables. Enlarging the gating system and adding additional gates to the ASTM mould can improve properties in the tilt position. The reproducibility of properties in as-cast and T6 heat treated bars was investigated.

Jan 1, 2004

By Heather Budney

Objectives 1. Evaluate the effectiveness of ON?s EA processes using criteria from the EA and policy sciences literature. 2. Recommend improvements to the EA processes and draw lessons from the ON case for the consideration of other jurisdictions. Evaluation Process 1. Chose criteria ? 14 primary criteria (Wood 2003) ? Subcriteria from Wood (2003) and Lasswell (1971) 2. Gathered information ? 6 key informant interviews ? Published literature, policies, legislation 3. Assessed criteria and formed Recommendations

May 1, 2008

By Sejong Kim, Younghoon Moon, Youngseon Lee, Eunyoo Yoon, Yonghyun Song

"Mg alloy has a high specific strength, however, their thickness reduction was limited on most parts because of their poor stiffness. Since the modulus of rigidity is an intrinsic property, improvement of modulus of rigidity to the enhancement of stiffness is impossible. Therefore, the modification of shape and structure is available method to enhance the stiffness of real part fabricated by Mg alloy sheet. There are many thin walled parts which are located in outer section of electromagnetic system.Poor stiffness is often shown on wide surface area part with steel sheet, which has also high modulus of rigidity. In these cases, various groove patterns are used to increase the stiffness of part. However, some different methods have to be used when general groove pattern can’t be used. So, we would like to propose some new method to high stiffness on thin walled precision forging of Al or Mg alloys.An effect of proposed method on stiffness enhancement can be confirmed by fabrication of prototypes as well as structure and forming analysis based on FEM."

Jan 1, 2015

By Brendan Parker, Tyron Rees, Steven Hart, Abba Manesh, Ian Mcgaffin

"In September 2009, Newmont began the commissioning of a 3 stage crushing and milling circuit at its Boddington Gold Operation in Western Australia. The Boddington ore has been recognized as one of the hardest and most abrasive ores treated to date and this played a pivotal role in the selection of crushing and HPGR technology for this operation as opposed to the more conventional SABC circuit.This paper will examine the scale up from laboratory to pilot plant and full scale operation of the crushing circuit. There have been many challenges to overcome in the first 18 months of operation; however, the HPGRs have in general met design expectations and performance is expected to improve further with ongoing design changes"

Jan 1, 2012

By Jeremy Breker

Cameco aligns its social and environmental responsibilities with its vision, mission and values. Environmental Leadership is established as a corporate objective that emphasizes the triple-bottom-line and a systematic approach to understanding environmental, social and economic issues, risks and opportunities. These are ingrained in the project culture, systems and processes and used to influence solutions derived by the project teams to achieve Cameco&apos;s objectives. This paper traces the organizational objectives from the early stages of a project through to implementation and turn over to Operations. A case study is used to demonstrate how an asset is influenced by Cameco?s strategy.

Aug 1, 2010

By A. M. Bell

General Summary THIS paper attempts to describe in a preliminary and general manner the nature of certain copper discoveries now being developed by Gaspe Copper Mines, Limited, in Holland township, in the interior of the Gaspe peninsula. Some copper mineralization appears to have been known here at the time of the earliest French explorations, was rediscovered in 1921, and has been under intermittent development by Noranda Mines since 1938. In the last two years discoveries have enhanced the picture so that the deposit now promises to develop into one of the important Canadian copper producers. As ideas are constantly changing with continuing development, any picture given now is very partial and tentative and must be subject to future revision. The nature of these copper occurrences differs from others known in eastern America. In many respects they have unique features but they are most closely akin to some copper deposits found away from the intrusive rocks in the porphyry copper districts of the western United States. The most important orebodies are replacement deposits in a limestone horizon in which the ore gangue is converted to skarn. These lie at considerable distances from any known intrusive but seem to have been derived from a buried stock of granite that intrudes the sedimentary rocks of Lower Devonian age. This intrusive has produced alteration effects in the overlying rocks that may afford a key to locating other ore areas in the Peninsula.

Jan 1, 1951

By G. E. Rowan

"DURING the dark ages, the cherished dream of chemists was to find a process for converting base metal into gold. Many a wealthy-but-gullible patron lost a fortune in the search. Men who work with metals today are a bit more realistic. I haven't heard of a metallurgist who expects to develop any one alloy that will resist all corrosive media. In the field of stain-less steels, there are about forty different types of alloys that are used where corrosion is a •problem.A stainless product is ordinarily selected because it offers one or more of the following qualities:(1) Resistance to corrosion (2) Resistance to oxidation at high temperatures (3) Good mechanical properties at room temperature (4) Good mechanical properties at high or low temperature (5) Attractive appearance (6) Ease of maintenanceToday we are interested in discussing the stainless steel family of alloys because of their .ability to resist corrosion. We• will not try to explain the Theory of Corrosion. Let us assume that, when surface potential and oxide formations are properly controlled, iron will resist attack in various chemi.cal solutions. The addition of alloying elements to iron does this for stainless steels. The principal stainless alloys used by various Canadian industries are listed in the accompanying Table."

Jan 1, 1959

By S. Amid, D. Fisk

"Wireless technologies are permeating the mining and metals industry and enabling a myriad of benefits. With standards such as IEEE 802.11 for wireless devices and ISA100.11a for wireless field instruments protecting their investments, customers look to benefit from the cost and flexibility offered by wireless devices. Using wireless field instruments, plants are eliminating the costs associated with wired system by 50 to 70% and using these savings to install more field instruments, which, when used smartly, enables them to optimize their processes efficiency and equipment reliability. Wireless also empowers a mobile workforce by allowing them to have access to key process and maintenance data directly from the field. This paper describes how wireless can help operations and maintenance personnel to be more effective. Three case studies, illustrating how the mining and metals industry is taking advantage of the technology today, are presented:1.,Optimisation of the water recovery process using wireless2.,Field operations improvement with wireless handhelds3.,Improving fleet maintenance through wireless mobile equipment management"

Jan 1, 2011

By G. Bimpilas, G. N. Anastassakis

"Today, one of the most intense problems in mineral processing systems is referred to the treatment of fine (–100 µm), and even smaller size, particles. Fine mineral particles possess specific properties (small mass, high specific surface area, and high surface energy per unit area) that render their separation inefficient with conventional methods (physical, physicochemical) and equipment. As a result, it is not feasible to obtain a concentrate both of high grade and recovery in mineral value and a considerable amount of mineral fine particles is lost to the tailings. As evidence, we could cite numerous examples from industrial practice with considerable loss of mineral values to the tailings because of the fine particles size, e.g. phosphate, tungsten, tin, etc.The objective of the current paper is to investigate the possibility to separate magnetic gangue minerals and rocks (serpentine, ilmenite, and olivine) from magnesite by co-agglomerating all the gangue components and subsequent magnetic separation of the agglomerates.To meet the target, hydrophobic agglomeration tests were initially carried out on single minerals to define the favorable conditions for selective hydrophobic co-agglomeration of the gangue minerals. In this respect, the effect of the following factors was examined: pH, collector dose, conditioning time, and settling time of the agglomerates. Among the combinations examined, the most favorable proved that with amine in the basic pH region. The use of non-polar oil proved beneficial. The preliminary results were confirmed by tests on mineral mixtures. The application of magnetic separation resulted in the removal of gangue minerals and the recovery of magnesite concentrates of commercial grade (magnesite content 95% approximately) and high yield.The current paper contributes to the development of mineral processing, since it successfully copes with a very important problem of mineral processing, such as the efficient separation of fine particles."

Jan 1, 2016