Search Documents

By Tatsuya Oki

Tantalum capacitors can be found mounted on printed circuit boards of domestic appliances such as personal computers. These capacitors contain a considerable quantity of expensive metal tantalum and can be detached and liberated from printed circuit boards by impact breakers. In this study, the size and density distribution of the liberated electronic devices were investigated. Then, tantalum capacitors were recovered from other electronic devices using size separation and pneumatic gravity concentration methods. More than 70% of Newton's separation efficiency was obtained for tantalum capacitors. High Newton's separation efficiency could be also obtained for other types of electronic devices such as chip resistors.

Jan 1, 2011

By V. S. Sastri, M. Elboujdaïni

"Corrosion rates of silicon brasses, highzinc yellow brass, low-zinc yellow brass, leadedtin bronze and silicon bronzes in both permanent-mold and sand-cast conditions were determined in soft water of pH 3, 5 and 8, and hard water of pH 8 at 70°C by electrochemical polarization technique. The alloys in permanent- mold condition showed greater corrosion resistance than sand-cast condition. Corrosion rates obtained from weight loss measurements showed no observable trend of a difference between permanent-mold and sand-cast alloys.The corrosion rates decreased with increasing pH of the medium. Silicon bronze and silicon brass showed high corrosion resistance while leaded-tin bronze showed the least resistance. Addition of small amounts of aluminum improved the corrosion resistance of silicon bronzes and silicon brasses. Alloys in permanent- mold condition showed greater resistance to dezincification than sand-cast alloys when average pit depth parameter is considered."

Jan 1, 1997

By D. V. Dorling, J. T. Bowker, J. A. Gianetto

Over the last few years, interest in the development and construction of large diameter, high pressure pipelines from the Mackenzie Delta in northern Canada and Alaska's North Slope has steadily increased as a result of the projected decline in recoverable natural gas from existing reserves in western Canada. The success of such enormous pipeline projects, which will require utilization of a strain-based design approach, is largely based on successful application of high strength line pipe steels, such as X80 and X100. To fully realize the economic benefits of high strength steels, welding processes and procedures must be developed to ensure that the requirements for high strength and good low temperature toughness are confidently obtainable in field girth welds used in the construction of such pipelines. This study aims to provide a better understanding of the factors that control weld metal strength and toughness for a series of mechanized X100 girth welds produced using a range of narrow-gap gas-metal arc welding procedures. The attainment of high yield strength (> 810 MPa) is considered to be an important target to ensure overmatching strength relative to the longitudinal property distribution of X100 line pipe steel. Some factors that have been considered in this evaluation include influences of gas-metal arc welding process variants (single and multi-wire) and changes in welding procedure specifications, including joint preparation. Key components of this work relate to the reliable measurement of weld metal strength variation through-thickness and as a function of position around the circumference of a given girth weld.

Jan 1, 2005

By D. Pawelus, J. Butra, R. Debkowski, M. Szpak

Impact of horizontal stresses on stability of underground workings in mines is a very important issue in underground mining. Identification of the initial state of stress in the rock-mass should be one of the main actions taken into account while designing and carrying out the mining activity in underground mines. The paper presents the tests on three dimensional stress pattern in Polish copper mines, owned by KGHM Polska Miedz S.A. Group, carried out in 2012. The research program covered 7 measuring stands in two mines; their average depth was about 1000 m. The main aim was to identify the values and directions of horizontal stresses in order to optimize the extraction and to improve the safety. The overcoring method with the use of CSIRO HI type probe was applied. The paper also describes the measuring technique which was developed for the purpose of specific mining and geological conditions of KGHM mines, taking into consideration the natural hazards encountered there as well as technical and operational capabilities with regard to drilling equipment. The experience gained during the underground measurements and the issue of making such measurements in underground copper mines in Poland are presented in the paper. The stress patterns obtained during the underground measurements are of application importance for the process of designing the spacing of mine workings and improving their stability and mine support selection.

Jan 1, 2015

By B. P. Verma, K. N. Sinha, N. M. Raju, B. Singh

The paper describes a new method of grouting bolts developed at the Central Mining Research Station at Dhanbad in India. This method makes use of wire-mesh sleeve instead of the expensive metal tube to insert the cement mortar into the drill hole. The field trials confirmed that the method is cheap and an effective system of support.

Jan 1, 1972

By M. I. Kalashnikova, Y. M. Shneerson, M. V. Keskinova

Interaction between mattes having various compositions and solutions with a wide range of free acid and non-ferrous metals concentration have been studied in terms of chemistry, mechanism and kinetics. The solution acidity and oxidizers to reducers ratio in the matte-solution-gas phase system have been demonstrated to be the major factors determining the process behaviour. It was found that the types of copper and nickel secondary sulphides resulted from nonferrous metals precipitation from solution, depend on of the solution and initial matte composition. Based on these studies, technologies of matte leaching and nonferrous metal precipitation in the form of rich sulphide concentrates are developed.

Jan 1, 2004

By D. H. Stonehouse

"ALTHOUGH final statistics are not yet available concerning Nova Scotia' s mineral production for 1958, it is estimated that the value will be slightly lower than that of 1957. In making this statement it is but fair to say that one year ago a reduction in mineral value was also forecast (for 1957 as compared with 1956) and final figures from the Dominion Bureau of Statistics ($68,058,743) indicated, instead, an increase of $2,000,000 over 1956. However, 1958 did bring problems to the industry which would indicate a drop in production value. The estimates figure for 1958 is $64,000,000. COAL Coal production came from 28 mines, 5 less than were operating since 1957. There were 5,269,896 tons of coal produced by 1,978,512 man-days' labour, for a tons per man-shift of 2.66 (0.05 higher than during 1957) or an increase of 1.9 per cent over the 1957 all-time high for this Province. This record has been established as a result of concentrated efforts to mechanize the coal mines of the Province, and it is hoped that it will be bettered during 1959. Collieries which showed some production for 1957 and none for 1958 were the McGregor at Stellarton, the Franklin at Sydney Mines, the MacLellan, the Rose bank No. 2 and the Rose bank No. 3 at Inverness."

Jan 1, 1959

By O. W. Borgeson, D. K. Honsberger, R. T. Bell

The Scully Mine, situated in the Labrador Trough near the Quebec-Labrador boundary, is one of the world's largest continuous ore deposits. This paper outlines the sequence of the mining operations from the planning stages to the delivery of the ore to the crusher at an average rate of 50,000 tons per day, 7 days per week. The principal equipment required to maintain this production rate includes four 12.\1.1-inch rotary drills, seven 8-cu.-yd electric shovels and a fleet of large haulage trucks. Particular attention is given to grade control, programmed by computer, drilling and blasting techniques and operational aspects inherent with open-pit mining in Canada's North.

Jan 1, 1969

By L. Dubourg, H. Habibi, D. Rasmussen

The combination of laser welding with Gas Metal Arc Welding (GMA W) forms the hybrid laser-OMA W welding. This process is an attractive tool with a high potential in welding lightweight structures, especially for aluminum alloys. For five years, this technology has increasingly attracted interest in both, industry (aeronautics, automobile, metal industries producing large structures) and academia (universities and research centers). Hybrid laser-OMA W welding process is generally accepted for its robustness, efficiency and flexibility. Coupling of a deep-penetrating laser beam with the heat and molten metal feeding of GMA W significantly expands the original welding application range of lasers. Its main advantages compared to the two individual components are deep and stable weld penetration, gap-bridging ability improvement, low distortion and easy filler metal addition. Hybrid welding allows a much wider groove tolerance compared to laser welding, especially for aluminum welding. Moreover, the reduction in distortion decreases the post-welding rectification needed and makes the assembly easier. In addition, if metallurgical factors are critical, the weld composition can be balanced with filler metal, decreasing the hot cracking susceptibility of some aluminum alloys. The combination of these two welding processes can also improve the weld bead shape quality (including the elimination of undercut), possibly reduce the porosity and increase the welding speed. This article reviews the recent works about the laser-OMA W hybrid welding of aluminum alloys. After a brief presentation on the interaction mechanisms between a laser beam and an electric arc, the paper depicts the typical welding parameters and experimental methods along with their characteristics.

Jan 1, 2006

By Tony Szwilski

Using Unity 3D as a collaborative multi-user virtual on-line environment, an interactive virtual underground mine platform (IVUMP) is being developed to provide on-line access to mine safety preparedness training with a focus on mine emergency response exercises (MEREs). Communication and information flow among MERE participants and their actions can be monitored, recorded and evaluated. A mine ventilation simulation utility VFIRE is being incorporated to enhance the realism and interactive nature of the ?in-world? exercises as well as extend its functionality to include training in real-time ventilation and fire control.

Aug 1, 2013

By A. Allaire, J. Torrealba-Vargas, R. Welyhorsky

Early testwork was carried out to select the plant process design criteria and flowsheet selection. Additional testwork was carried out during the feasibility study to support the optimization of the plant design criteria. The test results showed that the recovery of gold was not very sensitive to grind size in the range of 75 to 105 microns. An additional result was that the presence of lead nitrate did not improve the kinetics of gold leaching. This conclusion was supported by the low content of sulphides in the ore. It was also found that the presence of lead nitrate increased copper dissolution, producing the potential for an increase of copper reporting to electrowinning, which is detrimental to the overall gold recovery process. The use of oxygen in leaching was investigated to increase leach kinetics. The results of leaching tests to compare using oxygen instead of air indicated that, due to the improved leach time, it was possible to reduce the number of leaching tanks from twenty four (24) to twenty (20).

Jan 1, 2011

By A. V. Tarasov

There are still a number of copper smelters in the world using the roasting and smelting process flow diagram for treating sulphide raw materials. The technical, economic and environmental performance indicators of such operations are inferior to the respective indicators of advanced processes. First of all with respect to copper and sulphur recovery: 95% and 75% as compared with 98% and over 90%, respectively. Based on the studies of the single-stage smelting process to produce white metal and blister copper conducted during recent years an analysis of the feasibility of roastingsmelting technology improvement was carried out in the Gintsvetmet Institute to substantially increase the copper and sulphur recoveries. On the basis of this analysis, it was proposed to modernize the technology and equipment within the framework of the existing process flow-sheet. The proposed modernization implies an increase in the roasting temperature; higher desulphurization degree in the process of roasting; a number of modifications in the roaster design depending on the particular conditions of a given operation; addition of lime flux to the feed charge to roasting; and transition to combined calcium-silicate smelting slags. The metallurgical and energy computations made have indicated that the proposed modifications of the technology will improve the copper and sulphur recovery up to 98% and 90%, respectively. The required capital investments have been estimated using as an example a particular copper smelter, the payback period determined taking into consideration additional output, fuel saving and a reduction in fines for sulphur emissions. For comparison, the capital cost of a smelter modernization is given for change-over to basically new autogenous Ausmelt, Outokumpu and V anyukov smelting technologies.

Jan 1, 2007

By L. J. Cabri

A gold sample assaying 11.4 g Ault was selected for this study. Approximately 99% of the gold in this sample occurs as discrete gold minerals; the balance occurring as invisible gold in pyrite (determined by SIMS analysis). The sample was coarsely ground and sieved, yielding -38, 17, 22 and 22 wt.% in the -400+160 um, -160+80 um, -80+40 µm and -40 µm size fractions. Assays of the size fractions gave a gold distribution of -32, 20, 21, and 27% respectively. Processing with the hydroseparator (model HS-02) gave two tailings products and one concentrate from each size fraction. Assays of the concentrate from each size fraction gave gold recoveries of -7, 7, 24, 19%, respectively. Polished sections were prepared from each hydroseparation product and studied by image analysis to automatically search for gold minerals. Calculations were done using the surface area of the grains of gold minerals found on the polished sections.

Jan 1, 2005

By H. C. Gunnings, C. O. Swanson

"The Sullivan mine; at Kimberley in southeastern British Columbia; is the largest silver-lead-zinc mine in the Empire and one of the largest in the world.The original discovery was made in 1892 by four prospectors. Until 1899, when the branch line of the Canadian Pacific railway from Cranbrook to Kimberley was completed, little work was done on the property. In 1900, systematic development was started, and during the next 3 years 5,000 tons of ore was shipped to the smelters at Nelson and Trail. By 1903, some 300,000 tons of ore was developed, and a smelter was started at Marysville, about 5 miles from the mine. However, this smelter closed down in 1907 because of metallurgical difficulties after treating 75,000 tons, and the property came under the control of the American Smelting and Refining Company. An option on the property was taken in 1909 by the Consolidated Mining and Smelting Company of Canada, who exercised their option in the following year. During the next 5 years by selective mining and sorting 188,000 tons of high-grade ore was produced and shipped to Trail. This tonnage came from the upper levels, about 4,600 to 4,800 feet in elevation. At the same time, deep drilling down to the 3,900-foot level showed the presence of an immense body of complex ore. In 1915, the main adit-the 3,900-foot level-was started, and by 1919 this had been driven a distance of 2 miles to develop the ore above this level. Meanwhile, progress was being made in overcoming the milling problems. An interesting account of this work was written by the staff ( 4). In 1923, the first unit of the present concentrator was erected, with a capacity of 2,500 tons a day, and thereafter the rate of production increased rapidly. In 1934 it was around 8,000 tons a day, and to date a total of about 30,000,000 tons of ore has been sent to the mill. In recent years, a considerable part of the production has come from levels between the 3,900-and 3,350-foot, which were opened by an internal incline shaft started in, 1930. In 1942, tin was added to the products separated at the concentrator."

Jan 1, 1954

By E. E. Mueser

As Mr. Lundberg has already ably covered the theory of various methods of electrical prospecting, I shall confine my remarks to a consideration of the features which must obtain in an electrical prospecting method in order that it may be useful from a practical standpoint. These remarks I shall make with particular reference to the Elbof method. The successful application of all these methods rests, in the first place, upon the possibility of correlating theory, or empirically established facts, with the field data. Their practical usefulness, however, requires that the technique of making the field observations, and the procedure itself, be such that the method may be applied to large areas, under normal average conditions. The method, therefore, should not involve excessive preliminary labour costs to prepare the ground for actual prospecting work, nor should the prospecting work itself be so slow that its cost, when applied to extensive areas, becomes prohibitive. Moreover, it should be possible to apply the method even under difficult terrain conditions, such as rough topography and dense vegetation. It may be said of most of the methods referred to in the preceding paper, that, while they are interesting and theoretically sound, they fail to meet such practical requirements as I have outlined.

Jan 1, 1926

By J. Kempken, R. Hagmann, C. -P. Reip, W. Hennig

The CSP technology symbolizes a highly productive process for the cost-effective production of steel grades with a range of sophisticated properties comprising both the inner quality of hot strip, its surface formation as well as the relating technological characteristics. Thanks to extensive development work undertaken during the last 15 years, the range of steel grades that can be produced was continuously expanded and the process technology optimized. The present paper describes the ongoing development work concerning the production of higher-strength, microalloyed pipe steels. The resulting hot strip, due to the associated thickness and the potential pipe diameters, is particularly suited for being processed to HFI-welded pipes. Based both on ferrite-pearlite as well as very fine-grained, ferrite-bainite hot-strip microstructures, strength levels of up to grade API X80 can be realized. It can be demonstrated that hot strip produced in a CSP plant has very good toughness values at temperatures down to -60°C and can even make application with required sour-gas resistance possible.

Jan 1, 2005

By A. Mitura

The paper presents the initial investigation of possible energetic applications of chosen wastes from groups: 06, 03, 05 and 01, including coal slimes being secondary product of hard coal processing. These categories of wastes are catalogued according to the polish law, where 06 ? wastes from production, preparation, purchasing and application of products of non-organic chemistry; 03 ? wastes from wood processing and from plates and furniture, celluloid mass, paper and card board production; 13 ? oil wastes and wastes from liquid fuels; 01 ? wastes produced by searching, extracting, physical and chemical processing of ores and other mineral raw materials. The change of combustion heat value was evaluated in produced energetic mixtures containing these types of wastes together with the change of their individual components. All combinations of ingredients were taken into consideration giving 256 various mixtures, from which 36 were selected to investigation. This allowed the performance of statistical factor analysis. For such prepared materials the application of regressive method was proposed in purpose of calculating combustion heat value and then the comparison of empirically determined and theoretically calculated heat values was performed. The change of regressive coefficients can be determined by the nature of Hess law (eq. 1) what was investigated and the attempt of its explication and validation was done.

Aug 1, 2013

By A. D. Dalvi

Economics, Resources, Environment and Technology are the major driving forces in the base metals industry. However, these factors are intertwined and together will propel the industry in the future. The demand for metals has grown with economic expansion, between 2 to 4 % p.a. The current growth cycle has been driven by economic expansion in China where the demand for base metals has risen from - 7 % of the world demand in the 90's to - 25 % of world demand today, and rising. Base metals are commodities and their demand and price are cyclical. Historically metal prices have declined in constant dollars, forcing the industry to reduce costs, increase productivity and increase the scale of operation for economies of scale. Due to resource depletion and capacity expansion the industry is driven to expand its reserve and resource base. However, in the case of sulphide deposits of copper and nickel it appears to be a losing battle. For nickel the laterites represent a vast source at this time. Their development requires development of new technologies to make these resources economic. Emission reduction is being increasingly mandated in most jurisdictions with all governments enacting progressively more stringent regulations. The industry has been responding with technological innovation. With the Kyoto protocol there is a push to reduce energy intensity in metal production. Technological innovation is driven by all the other factors and is leading to novel ways of doing exploration, mining and processing, that would maximize resource delineation and utilization, reduce costs, increase productivity, reduce energy consumption, maximize asset utilization and reduce environmental affects. Development of alternative technologies such as Pressure Acid Leach of laterite for nickel, bio-leaching, heap leaching, SX-EW etc are being adopted to achieve the aims of the industry.

Jan 1, 2005

By Y. Chengxian

Many factors about the HIC (hydrogen-induced cracking) resistance of pipelines are discussed in this paper. The main factors that influence the ability of HIC are environmental and material factors. The chemical compositions, non-metal inclusions and microstructure are discussed in detail, while a group of tests on HIC resistance are done according to varying C, S, Mn and P contents in pipeline steels, different experiment time and different strength to the coupon. It is concluded that decreasing the amount of C and S can obtain good HIC resistance; the test time has an effect on the different microstructure of X70; microstructure is the most sensitive factor for the initiation processes of HIC.

Jan 1, 2005

By Les Philips

National Institute for Safety and Health?s (NIOSH, USA) Office of Mine Safety and Mine Safety and Health (OMSHR) has definitions for: -Proximity Detection as detection of personnel, vehicles and other objects near a machine using some type of sensor technology -Proximity Warning (aka Collision Warning) as detection of personnel, vehicles and other objects near a machine resulting in alarms that ?Warn the operator only ?Warn the operator and nearby personnel (two-way) -Collision Avoidance as the processing of sensor information resulting in control signals or actions that alter machine status/movement to avoid a collision by ?Computer control ?Human control

May 1, 2013