Search Documents

By T. Negeri, M. Boisclair

"A hybrid process consisting of flotation and magnetic separation has been developed to concentrate multi-phase rare earth minerals associated with a carbonatite ore that contains a significant amount of niobium. Fine grinding to a d80 of <65 microns was required to obtain acceptable separation of 92% of the contained total rare earth oxide (TREO) and niobium in half the feed mass. Whereas it was possible to obtain 85% of TREO in 28% of the feed mass through staged cleaning, it was demonstrated that at least 87% and 85% recoveries of TREO and Nb respectively could be achieved in 16% of the feed if the rougher-scavenger concentrates were calcined, quenched, reground to <25 µm and then magnetically upgraded. The paper discusses the overall concept of the flowsheet and the experimental strategies that led to this progress. INTRODUCTIONOut of the approximately 250 minerals known to contain rare earth elements (REEs), only about 60 of them contain REEs in significant amounts. Over 95% of the world’s rare earth oxides (REOs) are believed to occur in the form of three minerals (Pradip & Fuerstenau, 1991) namely bastnaesite (Ce,La,Y)CO3F, monazite (Ce,La,Nd,Th)PO4 and xenotime Y(PO)4. An estimated 51.4% of global REO resources are hosted by carbonatite deposits with the same three minerals as major constituents (Weng et. al., 2015). Any one of the REEs or commonly all of them can be found in these minerals (Ravnaas, 2010). As the demand for critical REEs increases due to the ever increasing applications in advanced technologies, many deposits containing other forms of REE minerals will have to be developed. REE minerals are extensively dispersed and intergrown with several oxides, silicates, carbonates, and phosphate minerals. Consequently it is possible to liberate them only at fine grinding and is thus difficult to separate and produce high grade rare earth mineral concentrates. Most of these minerals contain other important elements such as tantalum (Ta), niobium (Nb), uranium (U), and thorium (Th) in varied quantities. REE minerals in the same ore may exist as carbonates, fluorocarbonates, niobates, silicates, phosphates etc. in association with gangue minerals belonging to different mineralogical groups."

Jan 1, 2016

By A. Boeing

Rock-breaker automation and remote operation improves the safety and efficiency of mining operations. This article presents an overview of the Rocklogic rock-breaker automation system architecture that provides collision avoidance, automated parking, and remote operation functionality. The system consists of a distributed computer control system that interfaces with sensors attached to the rock-breaker, the rock-breaker hydraulics, and the site infrastructure. We present results of an automated Transmin rockbreaker installed in a production environment at an underground Australian mine site. The system has been in production use for over 900 days during which there have been no reported collisions, and 100% adoption of the remote operation technology. As a result, Rocklogic has significantly improved the safety of rock-breaking operations and reduced the rock-breaking cycle time, thereby improving the sites overall throughput.

Aug 1, 2013

By T. Bednarski, T. McCallum, L. Moya, L. Nsenga, B. Mbao

The accumulation of solids in solvent extraction (SX) circuits can cause problems with the physical and economic performance of the operation. These solids are responsible for the formation of crud, a solid stabilized emulsion containing organic, aqueous, air, and fine solid particles. The build-up of crud in SX settlers can limit SX operation throughput, require plant downtime, lead to higher organic losses, or result in higher aqueous in organic entrainment (all of which can have a significant, negative economic impact). Current practices for crud management are typically reactive. Crud is physically removed after it has been allowed to build to excessive levels in the circuit and processed mechanically using centrifuges or filtration. A new proactive solution has been developed to prevent crud formation and build-up. Low ppm dosage of an additive, ACORGA® CR60, into the pregnant leach solution (PLS) has resulted in reduced crud formation in pilot and commercial scale for a variety of PLS streams. This paper will review results from operations in North America and Africa, covering heap leach, concentrate leach, and agitated leach feeds. INTRODUCTION Crud formation and build-up in solvent extraction (SX) circuits has been a long time topic discussed and claimed to be crucial to the whole hydrometallurgical process (Liu, et al, 2006). Crud formation is present in all SX systems be it copper, uranium, zinc, etc., and Ritcey (1980) defined crud as a stabilized emulsion containing organic, aqueous, and fine solid particles. The ore type and feed composition is a major determining factor of crud formation and typically contains Si, Al, Fe, P, and sulfates (Ritcey, 1980). It typically builds at the interface between the organic and aqueous, but can also be observed as floating crud on the surface of the settler, or bottom crud, which is common to find in circuits treating agitated leach feeds such as in Africa. As crud formation has been unavoidable, many of the current crud management techniques are reactive, allowing crud to form and build in SX circuits. Once it does, it is removed and treated via different mechanical techniques, typically through some type of filtration or three-phase centrifuge, to remove the solids and recover the organic phase trapped within the emulsion (Ritcey, 1980). Automated pumping systems have also been designed and are frequently used in North American operations. The time and capital required to react to crud formation can be an overwhelming aspect to SX operation.

Jan 1, 2019

By E. Asselin

Electrochemical polarization experiments were conducted on alloy 625 in ammonia solution between 25 and 225°C and the results were compared with those of an oxygen solubility model. Results confirm that corrosion is under oxygen control, Normalized corrosion rates are determined based on the rate of oxygen diffusion to the corroding surface, and the corrosion rate at 200°C (-9.7 µA.cm-2) is roughly 24 times higher than the corrosion rate at 25°C (0.4 nA,cm-2), An oxygen-solubility model for Supercritical Water Oxidation (SCWO) conditions was generated using the Redlich¬Kwong-Soave (RKS) equation of state, Results of the model confirm many of the experimental observations from SCWO reactors which suggest that corrosion is at a maximum at temperatures just short of the critical point, The RKS/oxygen diffusion model predicts that the corrosion rate at 365° C is ?85 times higher than the corrosion rate at 25&apos; C. Given that a normalized corrosion rate is obtained, this type of model could be useful for selection of SCWO reactor materials.

Jan 1, 2005

By Hong Zhong, Shuai Wang, Fangxu Li, Guangyi Liu

"The flotation performances and adsorption mechanisms of a-hydroxyoctyl phosphinic acid (HPA) to malachite, cassiterite and wolframite were investigated by micro-flotation tests and X-ray photoelectron spectroscopy (XPS) analyses. The micro-flotation results indicated that compared with styrene phosphonic acid (SPA), diphosphonic acid (DPA), benzohydroxamic acid (BHA) and salicylhydroxamic acid (SHA), HPA exhibited excellent collecting power to the three oxide ores. In addition, HPA showed superior selectivity against hematite, tourmaline, feldspar and quartz. The results of XPS analysis demonstrated that HPA reacts with active species (M) on metal oxide by formation of P-O-M or P-M bonds.INTRODUCTIONIn mineral processing, flotation has been the main process for separation and recovery of valuable minerals from complex ores (Mei, 2013; Zhou, 2014). One of the key requirements in flotation process is to increase selectively the surface hydrophobicity of the targeted minerals by surfactant (known as collector in flotation) adsorption so that these mineral particles can preferably attach air bubbles in a slurry or pulp (Bai, 2004; Hankins, 2004). To anchor a solid surface selectively, special functional group are designed to adjust the interaction between the surfactant and the active sites of solid surfaces (Wu, 2006; Huang, 2014).Organic phosphorous compounds have strong affinity toward metals or metal oxides because they form more stable metal complexes than metal carboxylates (Pazik, 2001; Zheng, 1998). In mineral engineering, phosphorous compounds have been exploited as metal extractants and flotation collectors (Alguacil, 2002; Sun, 2008). Ni (2012) and Zhang (1998) introduced diphosphonic acid (DPA) as an effective collector for flotation of fersmite and niobite. Liu (1999) found styryl phosphonic acid (SPA) was a superior collector for flotation recovery of finely disseminated rutile ores. Gruner and Bilsing (1992) thought SPA was one of the best collectors for flotation recovery of cassiterite which could obtain a high-grade concentrates of more than 40% with high recovery values. Bulatovic (1999) investigated the flotation performances of phosphoric acid ester (PAE) to perovskite, ilmenite and rutile and found that PAE was an impactful collector for selective flotation of titanium minerals from complex ores in the presence of petroleum sulfate. However, a-hydroxyoctyl phosphinic acid (HPA) as a flotation collector for recovery of titanium ores were hardly reported in the previous literatures."

Jan 1, 2016

By G. M. Ritcey, S. H. Lucas

"On the north shore of the St. Lawrence River, in Quebec, are located orebodies of low-grade titaniferous magnetite. The Quebec Mining Exploration Company (SOQUEM), who have an interest in the deposits, believed that beneficiation of the could generate sufficient revenue to defray the mining costs and the costs of transporting the ore to a steel production facility. A joint research project of SOQUEM and CANMET investigated alkaline roasting of a magnetic concentrate, followed by leaching of the calcine and separation and recovery of Cr and V by solvent extraction. Aluminum was recovered by precipitation.The present paper describes the roast-leach bench-scale and pilot-plant work leading to the development of the optimum conditions f or the integrated process.A plant flowsheet was developed for the treatment of 5 x 106 tons of magnetic concentrate per annum. Estimates of capital and operating costs were made.Based on a recovery of approximately 90% V, 85% Cr and 75% AI, the total hydrometallurgical plant fixed capital costs, including mining, concentration and shipping, are estimated at $1.021 x 109; the operating costs are estimated at $131.92/ton concentrate. Annual revenue from the Na2CrO4.H2O, V2O5 and A12O3 produced is calculated to be $421 x 106.IntroductionThe Quebec Mining Exploration Company (SOQUEM) acquired in 1968 an interest in four titaniferous magnetite orebodies located in Eastern Quebec. 85 miles north of Mingan on the north shore of the St. Lawrence River. The Mingan deposit, with an estimated tonnage of one billion tons, has a reported average grade of 43% Fe, 6.3% Ti , 1.60% Cr, 0.19% V and 6.1% Al with minor amounts of nickel. SOQUEM, on the basis of previous bench-scale data, believed that the recovery of chromium, vanadium and alumina by alkaline roasting would generate sufficient revenue to defray the mining costs and the costs of transporting the ore to a steel production facility on the coast. One of the approaches selected by SOQUEM for beneficiation of the ore consisted of a combination of magnetic concentration followed by alkaline roasting of the calcine."

Jan 1, 1980

By J. B. Kwon

For improvement in the productivity of tall building projects, table formwork is one of the main methods that have been adopted for slab formwork. Because the table formwork method is an equipment-oriented construction method, the type of lifting equipment and method of operation considerably affects the productivity and cost of the table formwork. It is also important to make an equipment input plan for completing the table formwork within the time given, according to the structural construction cycle. For performing the table formwork, a tower crane or an independent lifting system, and shifting trolleys, are required. However, if an inefficient equipment input plan is made, exorbitant cost may be incurred. Therefore, the purpose of this study is to analyze the productivity of a table formwork, considering the type and number of lifting equipment and the number of trolleys inputted, and to suggest quantitative data for making a cost-efficient equipment input plan within the construction duration given. It is expected that the results of this research will be utilized as a basis for cost-efficient equipment input planning.

Aug 1, 2013

On the recent trip from Vancouver to Calgary with the President, Mr. C. C. Huston, and yourself, I had the opportunity of outlining a plan based on the following: Among the aims of the Institute are, obviously, the fostering of the confraternity of those engaged in the technical and management fields of the mining and petroleum industries. This may be achieved in a number of ways, of which, to me, the interchange of ideas and experience between different parts of Canada and different sections and divisions of the Institute appears to be one of the most important. I think you and the membership as a whole are, and have been, well aware of this. The annual tour of the President .and Secretary, particularly their visits to Branches, shows this to be true. The interchange of ideas through the medium of the BULLETIN also illustrates the point; indeed, most Institute activities are directed along these lines. I am convinced that much more could be accomplished if it became financially possible to do so. Many able and fine men are, I think, willing and anxious to give their time and energy to furthering these phases of Institute activity, but it is unfair to expect them to assume as well the financial obligations involved. Specifically, I would suggest that the following could be done if sufficient funds were available:

Jan 1, 1952

By Michael J. Rosko

Methods have been developed for processing and analyzing reflected solar radiation data obtained by Landsat 5 Thematic Mapper multispectral scanner. Spatial resolution for the Landsat series satellites is 30 meters per side per pixel. Materials on the Earth?s surface absorb or reflect different parts of the electromagnetic spectrum depending on their physical and chemical properties and, therefore, typically have characteristic spectral ?signatures?. Using these signatures, environmental parameters such as surface water and vegetation may be identified and analyzed. Principal advantages of the satellite image method for environmental monitoring include: a relatively long historic period beginning in 1985 for which information is available, the reliable numerical basis for the results, and the ability to assemble a historic environmental baseline and provide on-going monitoring for large or remote areas where standard monitoring methods may not be practical. However, because the long-term continued operation of Landsat 5 is problematic due to the age of the equipment, QuickBird and IKONOS satellite images were processed to determine if the two systems are sufficiently similar in their results to allow continuing monitoring using QuickBird data. The QuickBird satellite was launched in 2001 and collects the same visible and near infrared spectral bandwidths as Landsat 5, allowing for equivalent process algorithms for QuickBird, IKONOS, and Landsat 5 data. Spatial resolution for the QuickBird images is 2.4 meter per side, allowing for more detailed characterization of the land surface; spatial resolution for the IKONOS images is 4 meter per side. Because of several differences between the satellite systems, including degradation of the Landsat 5 sensor, it is necessary to calibrate QuickBird and IKONOS results to the Landsat results to verify similarity. Recent images from the satellite systems have been processed and results have been compared to determine the validity of comparing Landsat 5 and QuickBird/IKONOS images so that these newer data can be used reliably in the future instead of Landsat 5 data. Results from this comparison are presented in this paper and suggest that analyses for vegetation using the two satellite systems are comparable, and that little calibration is required. Results from comparison of surface water results from the two systems are less comparable and is currently being investigated by the authors.

Oct 1, 2009

By H. Ishimoto

It always has been a serious issue to improve safety in mine sites, demolition work sites, and civil engineering work sites. Especially, collision accidents caused by construction equipment damage not only the productivity of operations but also the health and life of workers in those work sites. To solve this problem, a variety of worker auto-detection means are developed so far, but they have not still become widely used in actual worksites. There have been two controversial points in the prior methods. One is that they were not enough in respect of the detection accuracy and certainty, and the other one is that the information of the detection results was not comprehensible to the operator of equipment. In this paper, the functional requirements of the obstacle detection system in earth moving work site is redefined at first, and then, it is proposed to apply a stereo vision to the obstacle detection system for an excavator. The system consists of horizontally arrayed two digital cameras with low distortion lens, an image processing controller, and a monitor for an operator in the cab. Stereo vision calculates the depth image from images of two cameras and detects the presence of obstacles, its distance, direction, and dimensions. Sensed obstacles are informed to the operator in the monitor image. Preliminary experiments are conducted with a stereo vision system mounted on a real equipment in a demonstration site. The result shows that two controversial points of the conventional technologies are improved, and that the applicability of this system is validated.

Aug 1, 2013

By Nehad Elsafty

It is always necessary to expand existing buildings, so that they could meet the growing societal needs. Compared with demolishing them and then constructing new ones, the expansion of existing buildings could not only reduce project cost, but also save the use of energy and raw materials in projects. Therefore, it is widely adopted in most under-developed countries. However, the expansion of existing buildings is not an easy task. It has been involved with a lot of issues in defining the scope of work, planning landscape, managing construction activities, etc. This paper investigates the potential challenges in expanding existing buildings. The project of expanding the Al-Agoza Hospital, one of the biggest and oldest hospitals in Cairo, Egypt, is selected as a case study. In the case study, the project documents have been carefully reviewed. The project engineers and the health-care professionals working in the hospital have been interviewed. This way, the point of views from the owner, the architect/engineer, and the contractor have been taken into account. Several lessons are learned through the discussion with these people. The results from this paper are expected to provide pieces of useful advice and suggestion for the expansion of existing buildings in the future.

Aug 1, 2013

By Yin Wang, Lin Li, Zhongwei Bi, Like Wei, Wen Li, Shaogang Li, Bin Zhang, Hongjie Li

Presently,Many long-wall fully-mechanized faces in shallow depth coal seams are below room and pillar goaf in Shendong mining area. When the working face is advanced out of concentrated coal pillar in upper room and pillar goaf, strong strata behaviors often cause support crushing accident. Aiming at a support crushing accident which happened in Shigetai coal mine of Shenhua group in Shendong mining area, this paper analyses the stress transfer process while mining out of concentrated coal pillar by numerical simulation software FLAC3D. According to the feature, simplifying the roof of upper room and pillar goaf as supporting-beam structure explains mechanism of large area collapse in room and pillar goaf roof. Based on the feature of supporting-beam structure, deep-hole blasting concentrated coal pillar technology is proposed to control the strong strata behaviors in Shigetai coal mine. The blasting control effect is confirmed through characteristics of strata behaviors, growth circumstance of ground crack and multi-point extensometer monitoring results. By using control technology, Shigetai coal mine has been successfully avoided support crushing accident.

Jan 1, 2015

By P. Leo

Al-Mg-Si alloys are widely used as medium-strength structural materials; extrusion is the most common processing route. In the present hot deformation investigation of a 6060 alloy, the microstructure of the alloy has been analyzed in the as-cast state, after homogenization heat treatment and after hot deformation by tensile tests in the range 400-490°C and 10-4 to 10-2s-1 on both as cast and homogenized alloys. After deformation the microstructure of the as-cast alloy exhibited cavitation. The flow curves at the lowest test temperature T show a gradual softening after a stress peak, being more evident for the alloy deformed in the homogenized state in association with a high yield stress; at higher T a plateau is attained which is lower as T rises and strain rates decrease. For each fixed T, the ductility decreases as strain rate increases for the homogenized alloy whereas, for the as cast alloy, it rises with strain rate. Constitutive analysis gives Q = 240kJ1mol for the homogenized alloy in agreement with published values; this indicates a more rapid strength decline with rising T than Al, suitable for good hot workability along with the lack of cavitation.

Jan 1, 2011

By M. E. Holter

"Five main lignite seams occur in the Tertiary Ravenscrag Formation in the Eastevan area, at depths of 100 feet or less. They are named, in ascending order: the Boundary, Estevan, Souris, Roche Percee and Short Creek seams. A total sequence of approximately 250 feet is represented by the coal beds and interstratified clays, silts and sands. Strata dip to the southeast at 25 feet per mile or less and trike northeast. Large areas underlain by coal seams at shallow depths are delineated. Reserve calculations are dependent on detailed information on seam thicknesses and feasible stripmining depths. The stratigraphically higher seams are thinner on the average than lower seams and this, together with the increase in elastic size fractions in higher strata, suggests a retreat of a Tertiary marine margin to the south during the closing depositional history of coal seams and associated strata."

Jan 1, 1972

By Timo Heikkinen

We have read, with great interest, Mr. Crocker&apos;s article on "Recent Trends in Autogenous Grinding," published in the October issue of The Canadian Mining and Metallurgical Bulletin. Referring to our paper, "Two-Stage Autogenous Grinding Investigations at Outokumpu," we can now report that last August we changed to this method at the Keretti concentrator. Prior to the conversion, the Keretti plant (see flow-sheet, Figure 1) had two primary rod mills, 6 ft. in diameter and 12ft. in length, in open circuit, followed by four secondary 9-by 12-ft. pebble grate mills in closed circuit with rake classifiers. Last summer, wl1en the Since August, grinding has been successfully carried out autogenously in two stages, with two mills being employed in the primary stage and four in the secondary. The size of the pebbles in the secondary mills is about the same as earlier -l V: i to 3 inches (Figures 4 and 5). Also, we generally prefer two-stage grinding to single-stage grinding because, in the former,

Jan 1, 1964

By S. Kelebek, E. Yalcin

This paper reports bulk flotation characteristics of a pyritic gold ore sample from the Barry District, Quebec using isopropyl and amyl xanthates. The ore sample was highly floatable with particles showing tendencies for self-aggregation that was most apparent in the first stage of flotation. A possible reason for this is discussed. The gold concentrate grade-recovery performance with respect to the particle size is presented for the rougher-scavengers as well as for the cleaners. The effects of copper sulphate as an activator, fuel oil and NaSH as a sulphidising agent are discussed along with the recovery by size behaviour.

Jan 1, 2011

By B. Grinbaum, A. Mazuelos, F. Carranza, N. Iglesias, M. Avila, J. L. Lozano, G. Perez, R. Romero, M. \/aliente

Following a failure of a tailings pond darn at a mine in Andalusia, Spain, a huge effluent stream, that contained about 1 g/1 Zn and significant amounts of ferrous, ferric, calcium, copper, aluminium and manganese cations has to be treated, to prevent pollution of a nature reserve. EGMASA, as the regional government environmental agency, suggested to improve the current depuration process by recovery of the Zn from the effluent. A solvent extraction (SX) followed by electrowinning (EW) was proposed and developed to remove zinc.. A pre-treatment stage consisting in bio-oxidation of ferrous iron by using a bacterial process followed by an alkaline precipitation was employed because iron in the effluent is incompatible with both the SX and the EW processes. The SX process was developed successfully at the laboratory scale and verified in a pilot plant on-site, using two Bateman Pulsed Columns for extraction and stripping of zinc. The results were satisfactory obtaining a recovery of 90% of Zn. The process was suitable for industrial application.

Jan 1, 2008

By A. R. Farkoosh, K. Korgiopoulos, McGill University, O. Rodop, L. A. Villegas Armenta

"New generation of Al-Mg-Si alloys with thermally stable dispersoids that prevent recrystallization and grain growth during hot deformation are currently used in automotive components requiring good formability. Alloy chemistry controls the phase formation especially age-hardening precipitates, dispersoids, and primary intermetallic which have pronounced effect on grain structure, strength and formability. In this work, thermodynamic calculations have been used to predict the effects of varying levels of Si (0.5-1.5wt%), Mg (0.5-1.5wt%) and Mn (0.1-2.5wt%) on phase selection. Thermodynamic calculations have been performed in equilibrium and non-equilibrium conditions via the FactSage™ software using the FTlite database. Selected compositions have been cast, heat treated, extruded and characterized through scanning electron microscopy with energy dispersive spectroscopy and electron channeling contrast imaging techniques. The calculations showed that at the hot deformation temperature of ~540 oC, exceeding certain Mg and Si levels would lead to retained *-Mg2Si intermetallics and Si particles at the grain boundaries in addition to a-Al-(Mn,Fe)-Si. It was found that retained *-Mg2Si phase which adversely affects formability can be avoided for Si+2Mg levels lower than 2.3wt%. FactSage calculations also showed that increasing Mn from 0.5wt% to 1wt% leads to an increase in the amount of dispersoids (from 1wt% to 2wt%) that can potentially slow down recrystallization and grain growth during hot deformation and improve formability. Calculations at room temperature also show that for an alloy with 0.7wt% Mg, excess Si beyond 0.7 wt% promotes the precipitation of Si clusters in the Al matrix that accelerate natural age-hardening. Results were confirmed by experimental investigation.INTRODUCTIONAluminum alloy 6082 (Al-Mg-Si) is used in the automotive industry because of its high strength, and good weldability (I. J. Polmear, 2006). The alloy is age-hardenable through the precipitation of ß-Mg2Si and its precursors, and the recrystallization is usually inhibited by Mn- and Cr-containing dispersoids formed through high temperature heat treatments (I. Polmear & Couper, 1988). However, it is known that minor changes in alloy chemistry (Mg/Si ratio) can have significant influences on the ductility and formability of these alloys by altering phase selection and the resultant microstructure (Gupta, Lloyd, & Court, 2001; McQueen & Celliers, 1997; Zajac, Hutchinson, Johansson, & Gullman, 1994). For automotive applications where wrought alloys (usually extrusions) are cold-formed to produce suspension components, the chemistry of the alloys and the extruded structure are of crucial importance as they determine the formability at room temperature (Asensio-Lozano, Suárez-Peña, & Vander Voort, 2014). In this study, thermodynamic calculations along with experimental investigations were carried out on the Al-Mg-Si system to understand their phase formation and precipitation hardening as a function of alloy composition."

Jan 1, 2016

By M. B. Greyver

The results of laboratory tests on iron precipitation from non-decopperized nickel anolyte are discussed. The parameters (pH, oxygen consumption and stirring speed) for iron precipitation from the anolyte, using the oxygen in the air, were determined. In the experiments conducted under optimized conditions, the residual concentration of iron in the anolyte after precipitation was 0.7-2.7 mg/L, and the copper and nickel losses to the solid phase were 0.05-0.07% and 0.05-0.16%, respectively. The filtration ability of the iron slurry obtained was 2 to 5 times higher as compared to that after chlorine oxidation and oxyhydrolysis. The leaching of the non-ferrous metals from the iron cake made using the separate nickel anolyte purification process was possible by dissolution in sulphuric acid. It was established that after cobalt precipitation from the copper- and iron-depleted anolyte, the precipitates obtained had lower ratios of Fe:Co and Ni:Co.

Jan 1, 2006

By G. Kipouros, M. Dadvand, A. Dadvand

"A novel methodology was developed to obtain a 3D porous layer with a high aspect ratio of porosity on a titanium electrode. The porous structure allowed more active material such as hydrous ruthenium oxide to be accommodated during the fabrication of the supercapacitor, resulting in an exceptionally high capacitance per surface area. The electrode demonstrated a remarkably high capacitance of 4,800 mF/cm2. The porous layer was composed of functionalized nanoparticles of TiO2 organized in a perfect 3D hexagonal close-packed array that resulted in a highly porous 3D structure. The layer was used as a template to electrolessly deposit a thin layer of silver prior to the electrodeposition of active material. KEYWORDS Capacitance, Porous, Ruthenium, Silver, Supercapacitor, Titanium RÉSUMÉ Une méthodologie innovante a été mise au point afin d’obtenir une couche poreuse tridimensionnelle (3D) affichant un rapport d’aspect élevé en termes de porosité sur une électrode en titane. La structure poreuse permet d’utiliser une matière plus active telle que l’oxyde de ruthénium hydraté durant la fabrication du supercondensateur, ce qui se traduit par une capacité exceptionnellement élevée par surface active. L’électrode affichait une capacité remarquablement élevée de 4 800 mF/cm2. La couche poreuse était composée de nanoparticules fonctionnalisées de dioxyde de titane (TiO2) organisées dans un arrangement regroupé parfaitement hexagonal en 3D, qui a engendré une structure en 3D hautement poreuse. Cette couche a servi de modèle pour le dépôt autocatalytique d’une fine couche d’argent avant l’électrodéposition de la matière active. MOTS CLÉS argent, capacité, poreux, ruthénium, supercondensateur, titaneINTRODUCTION There is a growing demand for integrating compact energy storage elements into electronic circuits due to the miniaturization of electronic circuits, sensors, and actuators, and the increasing importance of portable and wear-able devices incorporating more advanced electronic technologies that operate in controlled or uncontrolled environments to gather, process, store, and communicate information (Deng, Ji, Chen, & Banks, 2011; Beidaghi & Wang, 2012; Chen, Ramachandran, Mani, & Saraswathi, 2014). The manufacturing of compact energy storage elements needs to be compatible with the electronic circuit microfabrication processes. Recently, interest in integrating miniaturized supercapacitors into electronic circuits has increased due to their high charge–discharge rate and long operating life; however, ultra-high power miniaturized supercapacitors suffer from low energy density, hence requiring significant enhancement in their energy density for various applications (Deng et al., 2011; Beidaghi & Wang, 2012; Chen et al., 2014)."

Jan 1, 2019