Search Documents

By B. S. Prosser, K. G. Wallace, A. Akansobe

"This paper describes a ventilation project at the Wassa gold mine in Ghana. Golden Star (Wassa) (GSWL), a subsidiary of Golden Star Resources, owns and operates the mine. Golden Star holds a 90% interest in GSWL, while the Ghanaian Government holds the remaining 10% ownership, earning a 5% royalty on the gross revenue of GSWL’s gold production. Construction of the underground mine began in mid-2015 and pre-commercial production started in June 2016. Commercial production from the underground mine was achieved in January 2017. This paper describes the ventilation studies performed to support the initial development and production at the mine. The initial ventilation design included four, parallel surface exhaust fans. Future designs will include booster fans, new primary fans, and additional connections to surface. The paper describes the long-term ventilation planning goals and expectations as the mine achieves a production of 4,000 tpd with truck haulage to surface.INTRODUCTIONThe Wassa Gold Mine is located in the southern portion of the Ashanti Greenstone Gold Belt in Ghana, northwest of Tarkwa as shown in Figure 1. The mine has been in production as an open pit since 1998, with some minor disruptions, but the surface minable reserves have become exhausted and the mine started a transition to an underground operation in 2015. The underground mine was initially developed with twin decline accesses extending from the base of the open pit to the mining areas. The mining method selected was sub-level open stoping with cemented rock backfill. The original production level for the mine was 2,500 tpd with ore and waste transported by trucks hauling in the ramps to surface. In 2017 the production goal was set to increase to approximately 4,000 tpd. This resulted in an increase in the truck haulage fleet in addition to a significant increase in ventilation requirements. This paper describes the ventilation upgrades at the mine as it transitioned from a surface to an underground operation and the adjustments the ventilation system needed to make in order to accommodate a significant increase in production"

Jan 1, 2019

By B. C. Legg, G. L. Tiley

"Many of the ore bodies presently being developed are in remote locations and are, or will be, served by electrical power supply systems of limited capacity.The largest single components of the electrical systems of an underground mine are usually the production hoist drives; the power demands of these drives vary continuously throughout each hoisting cycle.Before 1970mine hoists were driven by either wound rotor induction motors or DC motors in conjunction with motor generator sets.Static Power conversion equipment now costs less to purchase and install and is claimed to be more efficient than motor generator sets. On the debit side, however, it can adversely affect the hoist motors, it operates at relatively low power factors, and it produces harmonic currents.This pa per discusses the effects of static equipment on both DC motors and AC power systems, and evaluates the relative consumption of the three classes of drives."

Jan 1, 1993

By E. L. Martheleur

A general expression for the electric power generated or consumed in a direct-current circuit is obtained by multiplying the reading of a suitable voltmeter connected across the terminals by the reading of an ammeter connected in the circuit. by the reading of an ammeter connected in the circuit. When alternating currents are considered, the product of the volts and amperes as obtained for direct currents does not generally represent the true energy involved; it is greater than this true energy and should be multiplied by a certain factor which may have any value between zero and unity, according to the conditions of the circuit. This factor is called the power-factor of the system, and expresses the ratio of the true energy over the apparent energy. For a three-phase system the expression of the apparent energy is [\/ 3 x E x I; ] while the expression of the true energy, that is, energy suitable for mechanical work, is [v? 3 x E x I x cos A.] The total current of a circuit corresponds to the reading of an ammeter connected in the circuit; it is the resultant of two currents. The first of these is in phase with the voltage, and is that portion which really produces mechanical work; the second is always in quadrature with the voltage, that is it may lead or lag the voltage by 90° according to the condition of the circuit. This second current does not produce any sensible work, and for this reason is sometimes called wattless current or reactive current.

Jan 1, 1924

By R. S. Douglas

Introduction The mine at Copper Mountain of the Granby Consolidated Mining, Smelting and Power Company was one of the pioneers in the use of blast-hole diamond drilling for ore breakage. This method of mining has now been brought to a high degree of perfection. The system in use has?been described in a previously published paper which has become an important part of the literature o the blast-hole drilling method. At the time of the establishment of the system at Copper Mountain, standardized loading and drilling procedures were set up. These procedures were based partly on the results of experiment and partly upon the judgment of men experienced in breaking rock in the mine. The success of the method has been proof of their adequacy. With the progress of scoping in the mine, the diamond drill method of breaking was applied to other ore blocks where different conditions obtained. It was found necessary to make adjustments in the standard procedures to get the best results under the new conditions. The following paper attempts to express, in terms of mathematics, the relations of the variable factors. Until recently, estimations of drilling required were based upon the tonnage to be broken and the proposed rate of explosive loading. A revised method of estimating is outlined below which is direct and which involves no unrelated variable factors.

Jan 1, 1947

By A. R. Farkoosh

Al-Si based alloys have been recently used by automotive industry for highly stressed engine applications. Due to severe working conditions of the engine parts, existing alloys hardly endure high pressures at high temperatures. This necessitates alloy modifications to enhance the elevated temperature performance. In this study, the effects of trace nickel additions on the microstructural and mechanical properties of A356+0.5Cu alloy have been investigated at different aging conditions. Electron probe microanalysis (EPMA), scanning electron microscopy (SEM) and X-ray diffraction (XRD) are used to study the microstructural changes. Aging curves have been obtained by hardness measurement. It was seen that the presence of additional nickel introduced many complex intermetallic phases within the microstructure which led to improved high temperature mechanical and aging response.

Jan 1, 2011

By Simon Houlding

"Part 1 (CIM Bulletin, August 1991) of this article identified the limitations of the traditional modelling methods and demonstrated the approximations and errors introduced by their application to complex mining situations. The objective of Part 2 is to describe the evolution of new, proven technology which eliminates these deficiencies and provides precise and practical alternatives. These promote the use of realistic geological and mining shapes and eliminate altogether the rectangular approximations of traditional methods. Limitations of the Traditional MethodsThe limitations of the traditional modelling method s (viz. simple block modelling, gridded modelling and their more recent variations) were discussed in detail in Part I . These methods are all based on the use of rectangular discretization to represent the boundaries and volumes of ore deposits and mining excavations. As a result they are unsuited to the representation of nonrectangular geological complexities such as folding, faulting and irregular surfaces . They are equally unsuited to the representation of realistic excavation limits, particularly in the case of underground mining.Recently these methods, with limited variations in technique, have been applied to increasingly more complex geological and mining situations. The resulting potentials for error and conflict within the modelling pro cess were demon strated in Part I . The effects can be summarized as follows:• volume and boundary approximations introduced by therepresentation of irregular three-dimensional boundaries andvolumes by rectangular modelling elements ; • geostatistical errors and conflicts caused by neglect of the relationships between grade estimates and the geometric/ spatial aspects of irregular volumes and associated observations (samples), including an inability to produce precise estimates with meaningful confidence limits;• a compounding of these effects by using rectangular element sizes other than the geostatistical optimum, and by using differentelement sizes within a model; and• general inefficiencies introduced throughout the modelling pro cess by the requirement to represent geology, grade distribution and excavation limits with a singular modelling method and model."

Jan 1, 1991

By M. P. Brameld, R. H. McCorkell

"Overburden covering bedrock uranium deposits was sampled to depths of 29 m and Rn concentrations measured at the same depths. Total-alpha activities, V concentrations and Rn emanation (J) of the samples were measured. The U-flux into the overburden was greater in the past: oxidation and dissolution has since removed most U, leaving decay products which indicate the presence of U deposits when U itself does not. Distributions of U and decay products and their ratios to each other reflect U-migration and degrees of U-removal. Rn distribution in overburden is related to the J of overburden samples and the presence and movement of groundwater. Simple, rapid methods of total-alpha and J measurement are described.IntroductionThe overburden drilling apparatus developed by Bondar-Clegg and Company makes possible sampling and radon measurement in overburden from the surface down to about 50 metres. This apparatus was used here to study the diffusion of uranium and its decay products from ore deposits into over lying overburden at the N deposit of the Amok Ltd. property (Cluff Lake, Saskatchewan) and on the Imperial Minerals Ltd. property at Gooderham, Ontario. These ores are enclosed in bedrock; the overburdens were deposited by glaciers or streams. The migration of uranium and its decay products in such situations and the factors which affect it have been little studied in the past, as readily usable techniques for mapping it in three dimensions have not been available. The results reported here are somewhat sketchy and preliminary, but they indicate the value of the methods used and some of the patterns to be expected. Surface and subsurface sampling and measurements were carried out on 3-line grids crossing known zones of mineralization. The lines were 60 metres apart at Gooderham and 40 metres apart at Cluff Lake."

Jan 1, 1982

By K. Esmaieli

The Synthetic Rock Mass (SRM) approach has the potential to capture the mechanical behavior of large rock samples. In order for the method to be used with confidence it is necessary to gain a good understanding of the factors that influences its analysis. This paper reports on a series of numerical experiments, based on field data from a large underground mine, to investigate the influence of intact rock mass strength of a constructed (SRM). A jointed rock mass defined by three fracture sets was simulated by a Discrete Fracture Network (DFN) model. The generated fracture network was subsequently embedded into six different intact rock samples, simulated by a bonded particle model in PFC3D, generating six SRM samples. Each intact rock sample was 7 m × 7 m × 14 m and assigned different mechanical properties. The first intact rock sample was assigned a uniaxial compressive strength of 205 MPa and an elastic modulus of 104 GPa with the UCS and elastic modulus values of the other samples downgraded by 10% until the weakest sample had a UCS value of 121 MPa and an elastic modulus value of 61 GPa. All SRM samples were loaded under uniaxial compression to obtain the complete stress strain curve. It was observed that the compressive strength of the rock mass samples decreased by 10% following the same trend as the rock material strength. However, the elastic modulus of the rock mass samples decreased non-linearly with reduction of the elastic modulus of the rock material. The Poisson's ratio of rock mass samples does not change with decrease of rock material properties. For the post-peak behaviour the results show that both the brittleness index and the residual strength of rock mass samples decreased as the rock material properties degrades.

Aug 1, 2013

By W. G. Hatch

Introduction Classified equipment originally installed in 1923 in the Britannia mill consisted of eighteen Model C Dorr Simplex classifiers, each in closed circuit with a pebble-mill. These machines were only three feet wide and of light construction, so that their raking capacities were necessarily limited, the maximum being about 20 tons per hour for each classifier. On conversion from pebble-mills to ball-mills, in 1924, attempts to increase circulating loads with higher rake speeds resulted only in overflowing a coarser product to the flotation cells. The elevator type of classifier was developed locally in 1935 and during that year two units, each having a sand carrying capacity of from 30 to 40 tons per hour, were installed. With such loads, a material increase in the grinding capacities of the ball-mills was noticed, and, after further development work on the elevator classifier, fifteen of the small Dorr classifiers were replaced by units of this type, capable of handling approximately 75 tons of sand per hour, with later alterations increasing this capacity to well over 100 tons per hour. In the meantime, the three remaining ball-mills had been placed in circuit with Dorr FX classifiers, one of which was six feet wide and the others five feet wide. Impartial and exhaustive tests conducted on the Dorr FX versus the elevator classifier showed the average results on these machines at Britannia to be substantially the same. A large amount of testing was carried on to determine the effect of circulating load on the output of the grinding units. This work indicated a rapid increase in the grinding rate as the ball-mill feed increased up to about 60 tons per hour, after which a relatively slow increase took place up to 100 tons per hour. No benefits were derived from higher circulating loads. A 300 to 500 per cent circulating load, depending on the nature of the ore treated, is considered to be within the economical range for the grinding of Britannia ores.

Jan 1, 1946

By Zhan Zhang, Hiromi Nagaumi, Zhen Li

"Recently, the remarkable strengthening effect of ??-Al(Mn, Fe) Si dispersoids at both ambient temperature and elevated temperature were found by several researches. A large amount of dispersoids can be formed by applying special heat treatments and within a suitable range of chemical composition of AA3xxx alloys. In the present work, the influences of Cr addition on the mechanical properties and microstructures of the Al-Mn-Mg-Si alloys were investigated. The mechanical properties at ambient and elevated temperatures were evaluated by micro-hardness and yield strength. Moreover, the microstructures in as-cast and heat-treated conditions were quantitatively analyzed by optical and electron microscopes. Results revealed that Cr also had effect on the number density and volume fraction of dispersoids. Micro-hardness and yield strength at ambient temperature increased with the increasing content of Cr, and the Cr addition increased the yield strength at elevated temperature as well. Moreover, the creep resistance at 300°C improved dramatically with the increasing content of Cr.INTRODUCTION Traditionally, AA3xxx aluminum alloys were widely used in packaging, automobile and architecture industries, because of its good formability, excellent corrosion resistance and weldability. And AA3xxx alloys were considered as non-heat-treatable alloys. However, the strengthening effect of dispersoids in AA3xxx alloys was discovered recently (Li & Arnberg, 2003;Li, Muggerud, Olsen, & Furu, 2012; Li, Zhang, & Chen, 2016; Liu & Chen, 2015).Alarge amount of dispersoids could precipitate by a proper heat treatment.In order to further improve AA3xxxalloys, the composition of the alloys should be optimized. A few previous studies were reported to investigate the influence of compositions on AA3xxx alloys. Adding Mn element could enhance the precipitation of ??-Al(Mn, Fe)Si dispersoids and improve the yield strength(Muggerud, Mørtsell, Li, & Holmestad, 2013), as long as the concentration of Mn was under the solid solution limit. Fe decreased the solubility of Mn and accelerated the precipitation rate of ??-Al(Mn, Fe)Sidispersoids(Li & Arnberg, 2003), the yield strength and creep resistance at elevated temperature could increase with an optimized content of Fe(Liu & Chen, 2016). Mg element would affect the nucleation process of ??-Al(Mn, Fe)Sidispersoids by forming metastable Mg2Si(Hirasawa, 1975; Li, Zhang, & Chen, 2017a; Lodgaard & Ryum, 2000), metastable Mg2Si precipitated during heating process and promoted the precipitation of ??-Al(Mn, Fe)Sidispersoids, moreover, Mg provided solid solution strength for AA3004 alloys(Li et al., 2016). Si increased the volume fractionof ??-Al(Mn, Fe)Sidispersoids(Muggerud et al., 2013)and decreased the size of ??-Al(Mn, Fe)Sidispersoids(Li, Zhang, & Chen, 2017b). With the addition of Mo, the size of dispersoids became finer with a higher volume fraction, the volume percentage of dispersoid free zones was reduced. Elevated temperature yield strength and creep resistance improved due to Mo addition (Liu, Ma, & Chen, 2017).However, the effect of Crelements on microstructure and mechanical properties of AA3xxx alloys were rarely reported."

Jan 1, 2018

By D. S. Conochie

The world is poised for rapid growth in consumption as large, less developed economies acquire greater wealth. It might be expected that there would be a corresponding growth in waste generation, but this might not necessarily be the case. The metallurgical industry has an excellent record of process development which has allowed it to provide a high tonnage supply of low cost, high quality metals. Environmental challenges have been faced and indeed the recycling of scrap iron through the electric arc furnace has made a massive contribution to cleaning up obsolete structures and equipment of past generations. Issues in waste generation and processing still remain, and the expectation for cleaner processing and environmental performance continues to rise. The waste impact of key process developments of the last century and the recent developments in metallurgical waste processing in Canada will be outlined. The potential to use state of the art design tools to produce the next generation of zero waste processes will then be explored.

Jan 1, 2004

By Scott Hean

"Environment and the economy are interwoven irrevocably. They need to be publicly discussed, and discussed often so that new approaches can be understood and developed - approaches which are complimentary, not confrontational.Discussion on the environment is timely, from the perspective of mining engineers and developers, from that of bankers and from their shared perspective as people concerned with enhancing the quality of life, the environment and the economy.This paper will touch on how what is called the ""environmental economy "" that has evolved has become entangled with regulatory and financial issues in a way that is dangerous for all of us. It will also look at some of the promising possibilities that a world-wide and continuing concern for the environment holds out for us.For many decades, British Columbia has provided some of the key examples of the intertwining of environmental and economic issues, and, very importantly, providing the people prepared to do something about them.Canada's first environment minister, the late Jack Davis, came from British Columbia. He led this country's delegation to the Stockholm Environment Conference in 1972, a conference that laid the groundwork of principles necessary to establish some international certainty as to the legal liability for causing trans-national environmental damage.Another British Columbian who was also a national environment minister, John Fraser - now the Speaker of the House of Commons - was one of the first to dramatize the importance of acid rain and force it into the international public arena.Some 20 years ago, British Columbians made Vancouver and their province one of the major centres of opposition to the Alaska Pipeline and Tanker System - with some justification, it now seems.That a British Columbian , then MP David Anderson, was given legal recognition to sue in a United States' court against a system that was either in U.S. territory or international waters was an important precedent in, and of, itself in terms of environmental law. That old controversy is now a very current case study - in terms of dealing with the question of liability.-"

Jan 1, 1991

By S. Masambi, S. M. Bradshaw, C. Dorfling

The presence of iron in base metal leach solutions complicates nickel and copper recovery processes. Leach solutions are commonly purified by precipitating iron as hematite, jarosite or goethite. Fast oxidation of ferrous to ferric is an important step to remove iron by precipitation at low pH values. This study reviews the ferrous oxidation mechanism and reaction rates in chloride media using molecular oxygen. This work contributes to the development of a better understanding of iron precipitation processing steps, which continues to be an important matter in hydrometallurgy. The specific objectives were to investigate (1) the effect of key process variables (acid concentration, copper concentration, and temperature) on the rate and extent of ferrous oxidation by dissolved oxygen and (2) the oxidation mechanism by varying chloride and hydrogen ion concentrations separately. Batch oxidation tests were performed using synthetic chloride solutions containing 45 g/L Fe and 3 g/L Ni at 50 and 80°C, dissolved Cu concentrations (0.3 to 3 g/L) and HCl concentrations (2 to 4.6 M). Regression analysis indicated that the significance of the effect of different variables on the extent of oxidation achieved after five hours decreased in the following order: HCl concentration > Cu concentration > temperature. Increasing the HCl concentration from 4 M to 4.6 M caused the degree of oxidation achieved after two hours to increase from 58.3% to 98.1%. The catalytic effect of dissolved copper on ferrous oxidation was more significant at low acid concentrations. Experimental data suggest that rapid oxidation of ferrous is possible at high HCl concentrations for two main reasons. First, the formation of ferrous chloride complexes allows ferrous oxidation to proceed without the formation of superoxide as an intermediate product (the rate limiting step in dilute acid solutions). Second, the formation of ferric chloride complexes stabilises the oxidation product.

Jan 1, 2016

By J. H. Schloen

"One of the most important phases in Canada's relatively rapid development of its metal mining and refining industries was launched in 1928 when the directors of Noranda Mines Limited decided to establish an electrolytic copper refinery ""somewhere in Eastern Canada”. Noranda's president, J.Y. Murdoch, had already evolved the company's ""mine to market"" policy and was determined to prove the economic feasibility of refining Noranda copper in Canada. The time appeared to be ripe as buoyant business conditions continued into 1929. In addition, proven ore reserves at the Horne Mine in northwest Quebec had virtually tripled and the price of copper had reached a healthy 15 cents per pound. Letters Patent incorporating the company bearing the date February 6, 1929 had been granted by the Secretary of State in accordance with an application that specified a capital structure of $2 million divided into 20 000 shares with a value of $100 each. Noranda assumed 70% of the original investment in the proposed refinery, while the Nicholas Copper Company of New York (which later became Phelps Dodge Corporation) and British Metal Corporation Ltd. of London, England, each were responsible for 15%. Nicholas Copper Company agreed to supply the design and to supervise the construction of the refinery and British Metal Corporation would act as sales agent and market the refinery's products."

Jan 1, 1999

By Z. Y. Liu

A local additional potential model (LAPM) was developed to illustrate the role of strain rate in stress corrosion cracking (SCC) of pipelines. According to LAPM, both density and mobility of the local active spots on the steel surface, i.e., dislocation emergence points, increase linearly with strain rate. Generation of such active spots introduces an additional negative potential locally, affecting the electrochemical reaction and, consequently, the susceptibility of the steel to SCC. Electrochemical corrosion measurements, slow strain rate tests and electrochemical hydrogen permeation test were combined to demonstrate the validity of LAPM to illustrate pipeline SCC in an acidic soil solution. It is found that a maximum of the SCC susceptibility occurs at strain rate of 10-6 s1, which is associated with an enhanced hydrogen evolution due to the local additional potential (LAP) effect.

Jan 1, 2010

By Madaah Hosseini H. R., P. Abachi, S. Miraghaei

In this study, the effects of milling time, chemical composition and heat treatment on microstructure and magnetic properties of nanocrystalline Fe-Si (6.5-25 at.% Si) alloys prepared by mechanical alloying have been investigated. The results show that increasing the milling time or the Si content, decreases the lattice parameter and increases the internal microstrain. The prepared powders mainly consist of micron-sized particles with an average grain size of less than 20 nm. The specific saturation magnetization values are slightly less than those of single crystal or conventional Fe-Si alloys and decrease as Si content increases. The coercive force values of the nanocrystalline as-milled powders are much higher than those of corresponding Fe-Si bulk alloys with a minimum at 13.5 at.% Si. The values of coercive force decreased after annealing but it seams that the residual strain developed during milling is not the major contributing factor to the higher values of coercive force in the mechanically alloyed powders and nanocrystals behave as single-domain particles without exchange interaction between them.

Jan 1, 2006

"Projections of demand for Alberta coal indicate a quadrupling of current production rates to some 70 million tonnes/year by the end of the century. About half of this output-comprised of subbituminous coal-will be required within the province, primarily for generation of electric energy. The remainder-roughly 70 per cent high-volatile bituminous (hvb) steam coal and 30 per cent medium- or low-volatile bituminous (mvb/lvb) metallurgical coal-will be exported, principally to Pacific Rim and Western European countries. Direct employment in mining and coal processing is projected to increase from the present ca. 3000 to at least 12,000 persons.This paper presents separate forecasts for subbituminous, hvb and mvb/lvb coal production in the period 1982-2000; notes a number of possible developments that could substantially modify these forecasts; and briefly discusses attendant infrastructure requirements. Attention is drawn to potential shortages of qualified manpower and to threatening inadequacies of transportation facilities.IntroductionDespite the dislocations triggered by the 1973 'oil crisis', energy budgets of Western industrial countries are mostly still in the very early stages of the anticipated transition to greater reliance on coal. Shift s to coal are still more often only talked about than being implemented; and the public policies which are essential for timely development of facilities for producing, transporting and using coal are in many instances not yet even broadly formulated, let alone enunciated.In these circumstances, long-range projections of coal demand and supply-even if restricted to internal requirements- are subject to greater uncertainties than usually afflict such forecasts.On the demand side of the equation, these uncertainties arise ultimately from linkages between a need for coal and the availability and pricing of OPEC oil. The current surplus of oil on world markets, which has recently forced substantial reductions of posted prices, is undoubtedly a transient phenomenon that is unlikely to have any long-term impact."

Jan 1, 1982

By P. K. Kaiser, S. Maloney, S. Yazici

"This paper focusses on the strength or capacity of cable bolts and introduces a new perspective for cable bolt design by demonstrating that mining-induced stress changes may affect cables in a detrimental manner. The concept underlying a novel cable bolt pull-out resistanceor bond capacity model is described and its practical significance is demonstrated by application to a simple two dimensional scenario of a fall-of-ground.A number of practical implications emerging from the application of this model are discussed to provide guidance to ground control personnel jar improving cable bolt support systems in mining applications. These include cable layout optimization, use of cable pre-reinforcements, assessment of embedment length requirements, need for plated cables (or straps), use of bird-caged cables (or buttons), and grout quality issues.IntroductionDuring the last decade, cable bolting has become a standard support technique in mining for handling wide spans, reinforcing are passes, preventing or reducing dilution of ore in marginally stable stopes, and for many other rock support need s.In its infancy, many deficiencies in cable bolt supports resulted from improper installation techniques and, in particular, grout quality control problems and the use of empty breather tubes (Goris, 1990). The development of special grout pumps and fail proof placement procedures (Oliver, 1992; Bourchier and O'Flaherty, 1992) have eliminated many of these early problems. Nevertheless, there are still situations where cables seem to lose their capacity during mining, and in these cases the cables do not provide the expected and needed ground support. In some instances, cables perform extremely well, whereas in others the same support layout and quality of support installation seem to be insufficient, allowing falls-of-ground or progressive cavings to occur."

Jan 1, 1992

By Barry J. Morash

The over-all slope angle of between 55 and 60 degrees at the Adams Mine necessitates control blasting on the final pit walls. The control blasting techniques used are pre-shearing and buffer blasting. Pre-shearing with 2'I2-inch holes on 5-foot centers is used in areas where jointing and rock type are not conducive to smooth stable walls. Buffer blasting with 12'/4-inch holes is used in areas where the rock is competent. Control blasting adds to the operating costs, but can result in substantial savings in increased slope angle and reduced stripping.

Jan 1, 1978

By David A. Fawcett

"This paper presents a summary compilation of current Canadian coal research projects in the areas of exploration, mining and preparation. The compilation forms the basis for a review of present operations and technology, and of current research efforts. General research areas, requirements and priorities are suggested along with a discussion on achieving the research goals in terms of funds, facilities and staff. The current level of research funding in these areas is assessed. IntroductionCanada's coal production is expected to undergo major expansion over the next two decades in response to domestic demands on coal for electrical power generation, industrial uses and conversion to synthetic .fuels, and in response to export demands for both thermal and metallurgical coal s. Surface mining will continue to dominate, but underground mining will contribute an increasing proportion to total production.In Canada, coal research, particularly in the areas of exploration, mining and preparation (E, M & P), has been limited. Increased impetus has recently been given to this research with expansion of CANMET's activities and with the establishment of the Coal Mining Research Centre (CMRC). University researchers are branching into coal research; strata mechanics and preparation are popular in mining-related fields.With the increase in number of organizations and individuals involved in coal research, a means of keeping abreast of the ongoing work is necessary. An annual summary of the status of and developments in current research assists in providing this information. The CMRC prepared such a summary for Canadian coal E, M & P research in 1979 and it received favourable response, justifying the effort. A 1980compilation has been prepared and pro vides the basis for this paper; it is presented with a brief discussion on background, format and content.The compilation forms a basis for an examination of the current status of Canadian technology in E, M & P and of the ongoing research in each area. General research requirements are reviewed and programs and tasks are suggested, followed by a discussion of research goals in term s of priorities and achievement. An assessment is made of the level of research funding in Canada, with comparisons drawn from the United States, the United Kingdom and Australia."

Jan 1, 1980