Search Documents

By W. W. Muir

"The Baker Mine used a 100-ton per day conventional cyanide leach mill located in northern British Columbia. A production decision was made in early 1980 and the mill was on fine in April 1981.Ore reserves had been estimated at 100,000 Ions averaging 0.9 oz gold per ton and 18 oz silver per ton . Mineralization consists of electrum (Au/Ag) and acanthite (Ag2S).This paper will review plant design and focus on some problems associated with start-up and early operation with the intention of assisting other mine operators by indicating potential problem areas.IntroductionThis paper will discuss operating strategies employed at Baker which improved over-all mill performance. Also included are some ideas which could be steps toward a more efficient operation in a similar setting.Actual dore production by mine life was 37,606 oz gold and 742,117 oz silver.Figure 1 illustrates the relative stability attained over the mine life. Metal recoveries for gold and silver were 92% and 85% respectively.Safety at Baker was of prime importance because of its remote location. Baker received the Mine Safety Association ""Small Mines Award "" in two of its three operating years. At shutdown in late 1983 the mill had operated for over 850 days without a lost-time accident."

Jan 1, 1985

By Alf Hartling

"Most of the Paleozoic section of the Williston Basin is a thick accumulation of numerous carbonate to evaporite, shallowing upward, cyclic sequences. These sediments were deposited in broad epeiric seas, and the deposition of the evaporite facies marked the final stage of each cycle. Many of the sequences display a pervasive replacement dolomite in the uppermost portion of the carbonate units. This secondary dolomitization is, at least in part, an early diagenetic event, synchronous with evaporite deposition.The inception of evaporite precipitation resulted in the seepage of a dense, Mg-rich brine into the underlying sediment. The heavy brine moved down the gentle regional dip displacing the more normal marine interstitial pore fluid and dotomitized the primary calcitic sediments en route. The supply of Mg-ions decreased away from the source, and correspondingly, the degree of dolomitization decreased and larger crystals formed because of slower nucleation at fewer sites.The seepage refluxion of dolomitizing brines gave rise to the frequently observed textural variation of cryptocrys talline, impervious dolomite grading into a finely sucrosic, permeable dolomite down-dip. This diagenetic facies change provides the critical up-dip barrier for potential hydrocarbon reservoirs. The lateral pool boundaries are controlled by either structural relief or a similar diagenetic facies change. The reservoirs are capped by the tight evaporites.Hydrocarbon production is attained from diagenetic traps in the Mississippian Oungre Zone and the Ordovician Red River 'C' Zone . Reservoir creation and the pooling mechanism are the result of dolomitization by the seepage refluxion of dense, Mg-rich brines beneath restricted, hypersaline lagoons. When formulating an exploration/ exploitation program for these oil prone horizons, it is essential to understand the complete geological history in order to establish where the reservoirs will be found and to define the areal extent of each accumulation."

Jan 1, 1984

By L. S. Jen

Canadian copper, nickel, zinc, lead and molybdenum mines are characterized by the mining of ores from which more than one metal is recovered. During the 1980s, approximately 15% of the gold, 25% of the zinc, 30% of the copper, 55% of the molybdenum, 80% of the silver and 90% of the lead produced from Canadian mines were produced as co-products and by-products of base metal mining operations. This trend is not expected to change significantly in the near future. The presence of co-products and by-products affects the level of production and the level of revenue from base metal mines in several ways: (I) in general, production of one base metal cannot be expanded or cut back without affecting the amount of production of another metal;(2) the commercial success of certain base metal mining operations depends on the substantial bonus revenues from co-products and by-products; (3) the quality and economic viability of many ore deposits are significantly improved by the presence of co-products and by-products; and (4) while coproduction is critical to the survival of some mines, bonus revenue from by-products can also be life saving to others during economic downturns. For these reasons, deposits with significant co-product or by-product values are likely to continue to be significant targets for exploration and for acquisition.

Jan 1, 1992

By M. Phylli Bray

"Concurrent with the continuing demise of many Canadian mining towns is the rise of a new method of providing remote mine sites with a workforce. This is the Long Distance Commute (LDC) which uses commuter labour and requires no permanent settlements to support the mine operation. It provides a flexible and cost effective method of operation to the industry and relieves both governments and industry of the expense of building and maintaining mining towns. However, little attention has been paid to the effect on workers or their families of the LDC work schedule whereby workers spend a fixed number of days at the site followed by a fixed number of days at home. Off-shore oil rig experience would indicate that negative social impacts may be expected. Research leading to an understanding of the problems involved seems to be indicated. One innovative suggestion has been to use already established but dying mining towns as workforce pick-up points for new LDC operations further north.BackgroundUntil recently, mine towns were considered as a necessary component of mine development. This was a natural symbiosis resulting from the need to provide workforce accommodation close to isolated mine sites. The early mine communities in Canada were often just a huddle of shacks around a head frame. Gradually mining companies began to provide housing which varied from basic duplexes and quads in grid pattern layout to professionally planned and designed towns, either model company towns or the more recent suburbs-in-the-bush, the so-called ""instant towns"" of the postWorld War II era of resource development. The improvement in accommodation reflected the need to attract a stable workforce as mine operations became more sophisticated. City amenities were expected and offered in these mine towns as a way of encouraging a permanent community of mining families. Indeed in towns like Manitouwdage, Schefferville, and others, it was not unusual to find a significant percentage of two- and three-generation families apparently providing the permanent mining communities so desired by mine operators."

Jan 1, 1991

By Paul Stothart

Agenda 1)Key Political and Policy Issues 2)Relevance to the Mining Sector ?All parties vying to be the greenest ?Regulation, indoor air, health issues combined into Clean Air Act ?International carbon markets ?Kyoto Protocol ?legal force ?Spawning clean energy technologies? ?Effectiveness of present approaches?

May 1, 2007

By E. Topuz, C. Duan

"INTRODUCTIONOperations research (OR) applications have experienced a substantial growth within the mining industry during the last three decades. The purpose of this paper is to present a summary of the results of a comprehensive survey of the application of various OR techniques to the major mining activities. It is hoped. through this sur vey , that the most widely used OR approaches, the important areas of application, and future trends have been identified.This survey included more than 500 articles published in this field in English since the late 1950s. Most of the relevant literature was found in mining publications, but, in terms of quality and originality, important applications were also found in literature not related to the mining industry. The sources constituted periodicals, proceedings research reports, and a few books. A listing of selected publications from which three or more articles reviewed in this survey appear is given at the end. Operations Research MethodologiesOperations research is concerned with optimal decision making in, and modeling of, deterministic and probabilistic systems that originate in real-life situation s. One basic feature of the OR methodologies is the attempt to optimize certain design parameters, subject to a set of constraints. This distinction has been employed in the survey as a guideline for selection of the techniques covered under the title "" OR methodologies"". The methodologies thus encountered in the literature are listed below. In a few cases, simulation has not been considered because it is not an optimization method per se."

Jan 1, 1989

By François Charette

High stress conditions in underground mines push the performance envelope of support systems to their limit. In weak rock masses these conditions lead to large deformation and breakdown of the rock material, while stress release events in hard rock mines can lead to sudden and usually violent rock and support failure. In typical support systems, a combination of different reinforcement and support mechanisms provide the required convergence control and retainment. These systems usually involve a multi-pass support installation. The advantages of a single pass support system are investigated and several bolting combinations are compared. Criteria for design are reviewed and new criteria are proposed to include cost and effectiveness in commonly used engineering approaches. Field observation and testing is used to illustrate the difference between the proposed approach and more conventional systems.

Nov 1, 2011

By Å. Partapuoli, M. Henriksson, P. Wikström, J. Worth, G. Adolfsson

The control of AG mills fed by ores with harder and softer components can be challenging due to the sensitivity of the mill to the ratio of hard to soft components. The mills at LKAB’s iron ore operations are generally well controlled, but there are periods when the throughput falls off dramatically, due to a loss of mill filling. As the ore is upgraded in the sorting plant through magnetic separation prior to milling, this presents an opportunity to manipulate the feed blend in advance. In order to assess this opportunity, a fullscale mill charge was dumped and assayed by size to quantify the build-up of competent waste in the mills. This was supplemented by pilot and locked-cycle laboratory tests at a wide range of feed blends in order to facilitate the development of an appropriate multi-component AG mill model. This paper reports the experimental campaign requirements and methodologies, as well as the major outcomes from analysis and modelling exercises using the industrial, pilot and laboratory multi-component data.

Jan 1, 2012

By W. Andrew Falls

Although we have yet to reach the midway point in the decade, the copper concentrate market has already witnessed some of the most volatile swings in history, moving from record high treatment and refining charges in 1991-92 to historic lows, in real terms, during the past year. What has been the cause for such volatility? By and large the swings can be attributed to factors of supply and demand in the "custom" copper concentrate market. For example, two relatively recent events which had a major impact on the supply-demand balance were the shutdown of the Bougainville copper mine in Papua New Guinea in 1989 due to rebel insurgency and the startup of the La Escondida mine in Chile in 1992. The first event, threw a balanced to slightly surplus concentrate market into a substantial deficit, forcing treatment terms down as smelters, caught short by the loss of concentrate supplies scrambled to cover their positions. The second event, brought over 300,000 mt per year of new copper in concentrate to the market, more than reversing the losses from the Bougainville shutdown. In combination with other additions to mine capacity via new mines or expansions, the custom concentrate market moved into a huge oversupply in 1991-92 and many mines found themselves unable to place uncommitted tonnage. But even this event was quickly overcome by the use of underutilized capacity at non-traditional buyers, such as those in the C.I.S., Zambia, or those which were not traditionally buyers of custom materials. All of this has happened in the space of five short years, a mere snapshot in the history of the market. I'll return to these points a little further on, but first I would like to review the fundamentals which govern the copper concentrate market.

Jan 1, 1995

By Yi-xin Zhoa

The characteristics of coal bumps are analyzed based on the microseismic data from No.8935 workface in Xinzhouyao coal mine, Datong Mining Group. The geology of this workface is characterized by the thick sandstone roof and coal seam, both with relative higher stiffness and strength. In order to investigate the mechanism and precursors of coal bumps occurred in No.8935 workface, the locations of microseismic, the relationship of microseismic energy and frequency and the spectrum of microseismic signals are analyzed. The result shows that the coal bumps in No.8935 workface were mainly induced by the seismic caused by roof failure. The coal pillar near the goaf is more easily to bump. The statistics results indicate that the coal bumps were mainly occurred in the gate road near the pillar, less than 50m ahead of mining face and located in the hard roof adjacent with coal seam. Moreover, the frequency, energy, b-value and frequency spectrogram of microseismic events were found to decrease before coal bumps. It was found that the frequencies of the microseismic events before coal bumps mainly concentrate upon 5~60Hz. The sudden decreasing of frequency and increasing of amplitude of microseismic events can be regarded as a precursor of coal bumps.

Aug 1, 2013

By Claude Bazin, François Robichaud

The control of the operation of a semi autogenous grinding mill is mainly based on power and bearing pressure measurements. Image based sensors can provide on-line measurements of the size distribution of the ore feeding a SAG mill allowing the control of this variable that impacts the operation of this equipment. This paper investigates the potential of using the information from such type of sensor to maintain a SAG mill feed target size distribution by manipulating the speed of the ore extractors below an ore stockpile. A PID and adaptive predictive controller for the size distribution are studied using a simulator for a stockpile and the equipments used for ore withdrawing from the pile. The proposed controller is found to give a good performance while remaining easy to tune.

Jan 1, 2014

By V. S. Gischig, G. Preisig

Hydraulic stimulation of deep reservoirs is an essential procedure for developing engineered/enhanced geothermal systems (EGS), but also in other Geo-energy contexts. The goal is enhancing permeability to such a degree that fluid flow rates within the reservoir are sufficiently high for an economically productive reservoir. Two fracture stimulation mechanisms are distinguished that may occur concurrently during the hydraulic treatment: 1) During hydro-fracturing (HF) new tensile fractures are propagated from the borehole by means of a fluid pressure overcoming the minimal principle stress d3 plus the tensile strength T0 of intact rock. In case of a pre-existing fracture oriented normal to d 3 , the fracture can be opened by exceeding d 3 only. Fluid injection is performed via small packed intervals for creating a stack of hydraulic fractures. 2) During hydro-shearing (HS), over-pressure induces slip along pre-existing fractures that are favourably oriented in the stress field for reactivation in shear. Such stimulation is usually performed in a large packed interval or in an open borehole. Which mechanism occurs predominantly during stimulation depends on the rock mass structure and in-situ stress field, but also on the orientation of discontinuities intersecting the open-hole section and thus being pressurized. Both mechanisms also differ in how they affect fracture permeability. While permeability gained by HS is mostly irreversible due to rearrangement of asperity contacts accompanied with shear dilation, permeability enhanced during HF reduces nearly reversible after pressurization unless proppant is used to ensure permanent apertures. In this contribution, we critically discuss the pros and cons of both mechanisms regarding efficiency of enhancing permeability and the associated hazard of induced earthquakes based on literature review and numerical modelling. We review literature that reports on how much permeability required for productive EGS reservoirs and how much permanent permeability can be gained by stimulation. We also compile information regarding the degree of seismicity induced during HFor HS-dominated stimulation procedures, together with conceptual studies that reveal characteristics of seismicity associated with the two mechanisms. Many observations and models indicate that HF may have a higher tendency of being aseismic, while felt seismic events are usually associated with HS. Further, we present a hydro-mechanically coupled fracture flow model that investigates, if and to what degree the stimulation strategy can be designed such that one of the two mechanisms is evoked and dominates over the other. It shows that HS may dominate in presence of larger persistent fractures nearly optimallyoriented in the stress field, even if HF is attempted in short packed intervals. The model further demonstrates that stress transfer during HS promotes the development of permeability across an anisotropic layer of the stimulated rock instead of a large volume. Hence, the study sheds light onto the feasibility of creating productive EGS reservoirs in crystalline rock at several kilometres depths.

Jan 1, 2015

By N. Tassé

Les substrats organiques sont à la base des biofiltres utilisant la réduction des sulfates pour générer de l&apos;alcalinité et diminuer la concentration des métaux dans des effluents contaminés. Afin de tester l&apos;efficacité de résidus forestiers utilisés dans de tels contextes, cinq types d&apos;écorce de nature et d&apos;âge variables ont été placés dans des contenants hermétiques et mis en présence d&apos;une solution synthétique de drainage minier acide. Le pH, l&apos;alcalinité et les concentrations de Fe2+ et SO4 2- ont été mesurés à intervalles réguliers pendant 70 jours. L&apos;importance d&apos;un éventuel neutralisant minéral et du type de souches de bactéries sulfato-réductrices pour l&apos;initiation et l&apos;évolution des réactions d&apos;oxydo-réduction ont été évalués en utilisant de la dolomite ainsi que des inocula de sédiments portuaires réducteurs et de boues d&apos;usine d&apos;épuration. Une augmentation de pH et des diminutions de Fe2+ et SO4 2- ont été notées dans tous les réacteurs. En l&apos;absence de dolomite, le pH augmentait de 1.6 à 5-6, Fe2+ diminuait de 400 à moins de 5-100 mg/L, et SO4 2- diminuait de 2500 à 750-1250 mg/L. Les échantillons inoculés avec des sédiments s&apos;avéraient légèrement plus performants que ceux avec boues. En présence de dolomite, le pH atteignait 6.5-7.0, et Fe2+ et SO4 2- tombaient à <5 et 20-40 mg/L, respectivement. Le degré de réactivité des résidus forestiers n&apos;était pas une simple fonction inverse de leur âge. Les échantillons ayant le mieux réagi, bien que parmi les plus vieux testés (années 1980), étaient ceux contenant une proportion significative d&apos;écorces de feuillus et peu de bran de scie. Les échantillons avec des proportions élevées d&apos;écorce de conifères ou de bran de scie étaient associés à des taux de réduction moindre. Nonobstant l&apos;amélioration rapide des conditions obtenue avec la dolomite, grâce à une neutralisation initiale plus prompte, il s&apos;avère que le type de résidus forestiers éventuellement utilisé dans une barrière réactive est de première importance pour l&apos;efficacité des mécanismes de réduction. Un système basé sur l&apos;utilisation de résidus forestiers devrait utiliser des écorces (plutôt que du bois) provenant de feuillus (plutôt que de conifères).

Nov 1, 2002

By R. Shamsodini, A. Poor Zaeif Doost, H. Haji Amin Shirazi, M. R. Garmsiri

"With columns being installed in rougher section at Miduk Copper Complex, the rougher feed mainly reports to rougher-scavenger cells. To evaluate the efficiency of regrinding circuit, we conducted flotation experiments on samples of the feed and the products of the regrinding circuit. The grade difference of these products at 85% recovery was considered as the efficiency index. Results show that, with weight recovery of the rougher-scavengers the efficiency of the circuit increases. Exclusion of the rougher-scavenger concentrate from the feed to the regrinding circuit, resulted in an increase in the efficiency index from 10.12 to 17.6%.INTRODUCTIONThe flotation circuit at Miduk Copper Complex consists of five flotation columns as roughers and ten mechanical cells as rougher-scavengers. According to design criteria, 75% of the final product was expected to be produced by the rougher columns, while most of the feed consisting of liberated valuable particles is introduced into rougher-scavengers. To liberate locked particles, the rougher-scavengers concentrate is introduced into the regrinding circuit (see Figure 1 below). The regrind mill is in reversed closed circuit with a secondary hydrocyclones cluster, and the cyclone overflow is introduced into three parallel cleaner columns. Cleaners concentrate reports to concentrate thickener and the column tailings is introduced into six mechanical cleaner-scavenger cells. The cleaner-scavengers concentrate reports to the regrind circuit(Figure 1)."

Jan 1, 2012

"This paper describes an alternative method of vehicle control which uses a micro-processor to control the field current and armature voltage concurrently. The field tests carried out and the conclusions drawn from the basis of the paper.IntroductionIt is generally accepted that the main obstacle to a greater use of electric vehicles is the relatively poor range and performance when compared to alternatives such as diesel and petrol-engine vehicles. Much effort has been applied to the problem of increasing the energy storage density of batteries and considerable improvements are now being reported.Improvements in the efficient use of the stored energy, although unlikely to achieve the necessary increase in range and performance for a widespread acceptance of electric vehicles, can nevertheless make a useful contribution. Because the improvement in efficiency is achieved by a reduction in losses, it follows that the temperature rise in drive-train components is reduced. These advantages, coupled with the increasing cost of energy, make improvements in the efficient use of the stored energy desirable, if not absolutely necessary. To achieve this with the large and rapidly varying loads encountered during the operational use of a vehicle will require a more flexible system of control than that provided by the current limit. This paper describes an alternative method of control which uses a micro-processor to control the field current and armature voltage concurrently.The value of these parameters is selected to supply the power demand at the motor shaft, with the minimum losses in electrical transmission, thus increasing the efficiency with which the stored energy is used."

Jan 1, 1982

By J. H. Archibald

"In mines employing cut-and-fill stoping (sand fill), ore passes are built as mining progresses upward. These ore pass raises are generally made from timber and form a vertical ""chimney"", like a very tall log cabin. Traditionally the chimney, or raise, is square in shape and is constructed from square timbers with stepped ends as shown in Figure I. The timbered raise is thus surrounded by sandfill on its outside, leaving the centre open for passing ore down through it. Each layer consists of four timbers and rests flush on the layer below. The corners are frequently pinned or spiked.Under certain conditions in sandfilled stopes large horizontal loads may be transmined to the raise cribbing timbers, or the ""chimney&apos;s"" walls. In deep mines, where rock bursts are a problem, it can be shown that one of the conditions for rockbursts to occur is that the burst zone be stiffer and weaker than the surrounding rock(l). This allows a strain energy build-Up in the rock surrounding the burst zone, and the rate of release of this strain energy is known to be related directly to the over-all strength and stiffness of the rock in the burst zone. In stopes that are sandfilled, attempts are, therefore, usually made to increase the strength of the sandfill by the addition of large-sized waste rock and Portland cement. These measures usually achieve the desired strength of the sandfill and, consequently, the severity and frequency of rockbursts can be reduced.Problems may arise when the now chunky sandfill transmits high loads to the raise cribbing along with relatively large move- merits. This leads to heavily stressed and strained cribbing timbers the Coeur d&apos;Alene district in Idaho, raise cribbing failures are common. A typical mode of cribbing failure is shown in Figure 2. One learns in statics that a structure shaped like the crib in Figure I is inherently unstable , at least from a structural standpoint. The crib has pivoted, in Figure 2, into a rhombi c shape and supports very little load. Soon the four-foot square raise cribbing made from 5 in. by 5 in. timbers will no longer pass ore."

Jan 1, 1991

By Sylvie Poirier

This paper focuses on new developments regarding thermal rock fragmentation applications. The technology consists in a strong burner powered by diesel fuel and air. The thermal reaction, which is created, allows for the enlargement of 125-mm to 450-mm holes by breaking the rock in a spalling effect. It has been used for over 30 years in Russian open pit mining. Following an agreement between Dynamitage T.C.G. Inc. and the owner of the technology, major improvements have been brought to this technology, allowing for the fabrication of a prototype suitable for the Canadian industry. In Russia and Ukraine, thermal rock fragmentation is actually used to drill large diameter holes in surface mining. Upon having acquired a better knowledge of this technology, it seems that it presents a great potential for selective mining in narrow-vein operations, for either surface or underground mining. Rocmec International Inc., a subsidiary of Dynamitage T.C.G. Inc., and Natural Resources Canada are technical partners in the evaluation of the operational parameters and environmental aspects, such as gas, heat, dust and fog emissions. Furthermore, Canada Economic Development is a financial partner in this project. This paper presents the technology and its history. It also reports on the changes brought to the equipment to adapt it to North American environments. A summary of the tests realized since 1995 is provided, along with the main conclusions obtained. The anticipated applications for the use of this technology in both surface and underground environments are described, such as open pit mining, bulk sampling and narrow-vein ore extraction. An estimate showing a comparison between the thermal fragmentation mining concept and the long-hole mining method is presented and, finally, the future developments planned are listed.

May 1, 2002

By Robert D. Brown

"The Conservative Government &apos;s budget proposals brought forward on December 11, 1979 have been withdrawn, but they are far from dead. On the contrary, a number of those budget proposals, especially the ones which would close loopholes and result in other technical changes being made to the Income Tax Act, should be considered to be alive and well.It is not unreasonable to expect the next government, of whatever political persuasion, to reintroduce many of these technical changes in the next federal budget. For that reason, last December&apos;s budget may have offered an interesting preview of what the mining industry and other taxpayers can expect in 1980. It is quite possible that some of these changes may be effective as of the original dates announced in the withdrawn budget proposals.This month, ""Tax Notes"" reviews the main pro visions of Mr. Crosbie&apos;s December, 1979 budget, with a primary focus on the changes that would have affected the resource sector.It must be emphasized that all of the budget proposals discussed herein have been withdrawn, that none of them are law and that any actual changes in our tax rules will have to be dealt with by the new Parliament that will be assembled following the February 18 election. December 1979budget withdrawnThe federal budget proposals brought forward by Finance Minister John Crosbie on December II, 1979 were withdrawn as a result of the defeat of the Conservative Government on a motion of non-confidence in the House of Commons on December 13. However, it appears quite possible that at least some of the proposals may be introduced into Parliament at a future date, possibly with retroactive effect.In a press release issued by the Department of Finance, Finance Minister John Crosbie stated that if the Conservative Government is returned to power, it will reintroduce all of the measures contained in his December II budget.Mr. Crosbie stated that all of the income tax measures contained in the budget would be reintroduced, effective on the dates indicated in the Notice of Ways and Means Motion tabled on December II. Some of the more important measures in December II budget, and their effective dates as indicated in the Notice of Ways and Means Motion, are discussed below.The December budget had also introduced or increased excise taxes or duties on gasoline, wines, cosmetics and photofinishing. If the Conservative party is re-elected, these measures will be reintroduced with prospective effect (i.e . effective as of new dates to be announced in the new budget)."

Jan 1, 1980

By M. Hozayen, E. S. Radwan, P. A. Nawrocki, A. Jebbouri

"A major geomechanical study was conducted for one of the UAE onshore oil fields with the purpose of studying reservoir rock properties and stress distribution, based on which a 3D coupled reservoir geomechanical model was built. This model was later used for wellbore stability analysis and for analyzing the effect of fractures on future reservoir production performance, including fracture deformation and permeability evolution occurring due to reservoir depletion and resulting changes in local stress field. The subject of this study was a complex fractured Upper Cretaceous carbonate reservoir characterized by high degree of heterogeneity, both vertically and laterally. Wellbore instability related drilling problems were encountered while drilling the wells in this field. The problems were mainly in drilling the horizontal wells, including breakouts and mud losses. Experimental results of laboratory tests are summarized in this paper whereas wellbore stability analysis and formulation of a 3D geomechanical model that was built for that purpose is summarized in a sister paper (Part II).A suite of tests reported includes tensile strength, uniaxial and triaxial compression and permeability under stress at simulated reservoir conditions. All tested rocks have been grouped into twelve test units and reservoir geology, rock types and challenges related to designing a viable sampling and testing program for a big reservoir are discussed first followed by sample selection criteria and details of the testing program. All test units showed brittle behavior at zero confinement and some samples showed similar behavior at low confining stresses. With confining stress increase, the behavior gradually turned to plastic but some samples showed features of ductile behavior even at low confinement.Obtained experimental data have been summarized in the form of strength criteria and correlations. The Mohr-Coulomb strength equations were obtained for each test unit and also for the averaged values. It was noticed that triaxial compressive strength (TCS) increases with decreasing porosity or increasing density but their influence on TCS is getting smaller with confining pressure increase. Good correlation of porosity and density with Young’s modulus, Poisson’s ratio, unconfined compressive strength (UCS), friction angle, cohesion and tensile strength has been noticed and there was an increasing trend between the confining pressure and TCS. Rock type (mud or grain supported) was not influencing the TCS as much as porosity and density and the two lithologies encountered affected TCS approximately in the same way. These results and correlations are summarized and explained in this paper. They were further used in the numerical modelling part (Part II) of this paper, Hozayen et al. (2015). It is also concluded that rock lithology is not a decisive factor and mechanical properties of tested rocks should be rather considered dependent on porosity and permeability. This helped greatly in reducing the number of tests that had to be performed."

Jan 1, 2015

By Stephen C. Tadolini

"The use of a torque wrench to establish the amount of actual load developed on an expansion anchor bofting system dates back to work completed in the early 1950s. The advent of ultrasonic measurement systems and hydraulic torque wrenches has made it possible for the U.S. Bureau of Mines to perform torque-tension measurements in the laboratory and the field much more accurately. The results indicate that the amount of initial boft preload may be overestimated by amounts in excess of 45% of the expected load using torque wrenches. This inaccuracy is primarily due to the friction that occurs between the bearing plate and the head of the boft. These parameters become extremely important when the support system is being used to prevent joint members from slipping relative to each other or when the boft acts as a heavy spring to clamp two or more sections together. Methods to overcome the frictional losses are presented in conjunction with a laboratory method to determine the actual torque-tension ratios for expansion anchor and combination bolting systems.IntroductionMechanically anchored roof bolts have been widely used in the mining industry since their introduction in 1947. Estimates made in 1989 indicate that out of 85 million fixtures, approximately 49 million bolting fixtures still use applied tension to complete the reinforcement necessary to maintain stable openings. Nearly 85 million bolts are used yearly. The most widely used bolt is the resin-anchored headed rebar, followed by standard mechanical roof bolts, specialty bolts (mechanically anchored, resin enhanced fixtures) , and combination bolts . Po st-tensioned resin rebars, combination systems, and friction stabilizers make up the remaining 10% of the units used (Fig. I).For mechanical, combination, and tension rebar bolts, the bolt tension is the primary means of reinforcing the roof, but in many cases, because of poor installation procedures, the bolts are ineffective. Mine operators recognize the importance of proper installation procedures. Long-term bolt tension measurements are required in the Code of Federal Regulations (CFR)In each bolting cycle, the actual torque or tension of the first tensioned bolt installed with each drill head shall be measured immediately after it is installed. Thereafter, for each drill head used, at least one roof bolt out of every four installed shall be measured for actual torque or tension. If the actual torque or tension of any roof bolts measured is not within the range specified in the roof control plan, corrective action shall be taken."

Jan 1, 1991